Engineering Commons^™

3d Microwave Tomography Using The Soft Prior Regularization Technique: Evaluation In Anatomically-Realistic Mri-Derived Numerical Breast Phantoms, Amir H. Golnabi, Paul M. Meaney, Shireen D. Geimer, Keith D. Paulsen

Department of Mathematics Faculty Scholarship and Creative Works

Objective: Fusion of magnetic resonance imaging (MRI) breast images with microwave tomography is accomplished through a soft prior technique, which incorporates spatial information (from MRI), i.e. accurate boundary location of different regions of interest, into the regularization process of the microwave image reconstruction algorithm. Methods: Numerical experiments were completed on a set of 3D breast geometries derived from MR breast data with different parenchymal densities, as well as a simulated tumor to evaluate performance over a range of breast shapes, sizes and property distributions. Results: When the soft prior regularization technique was applied, both permittivity and conductivity relative root mean …

Fabrication And Characterization Of Centrifugally Spun Poly(Acrylic Acid) Nanofibers, David De La Garza, Francisco De Santiago, Luis Materon, Mircea Chipara, Mataz Alcoutlabi

Mechanical Engineering Faculty Publications

The production of poly(acrylic acid) (PAA) nanofibers by the centrifugal spinning of PAA solutions in water is reported. The effect of the spinneret rotational speed and concentration of PAA solutions on the diameter of nanofibers and on their quality (assessed by the absence of beads) is discussed. The main physical properties of PAA such as glass-transition temperature (Tg) are studied in detail and compared to the feature of the as-received homopolymer. It is shown that the glass-transition temperature of the bulk PAA and PAA nanofibers (as measured by differential scanning calorimetry) depends on the heating rate according …

A Sine-Summation Algorithm For The Prediction Of Ship Deck Motion, Christian R. Bolander, Douglas F. Hunsaker

Mechanical and Aerospace Engineering Student Publications and Presentations

Landing a fixed-wing aircraft on a moving aircraft carrier is a risky and inefficient process. Having an accurate prediction of ship deck motion decreases the risk posed to both the pilot and the aircraft and increases the efficiency of landing maneuvers. The present work proposes the use of a sine-summation algorithm to predict future ship motion. The algorithm decomposes recorded ship acceleration data into its characteristic harmonic parameters using a fast Fourier transform. The harmonic parameters are then used in a summation of sine waves to create a fit for the acceleration data, which is projected into future time intervals …

Assessment Of Post-Wildfire Debris Flow Occurrence Using Classifier Tree, Priscilla Addison, Thomas Oommen, Qiuying Sha

Michigan Tech Publications, Part 1

Besides the dangers of an actively burning wildfire, a plethora of other hazardous consequences can occur afterwards. Debris flows are among the most hazardous of these, being known to cause fatalities and extensive damage to infrastructure. Although debris flows are not exclusive to fire affected areas, a wildfire can increase a location’s susceptibility by stripping its protective covers like vegetation and introducing destabilizing factors such as ash filling soil pores to increase runoff potential. Due to the associated dangers, researchers are developing statistical models to isolate susceptible locations. Existing models predominantly employ the logistic regression algorithm; however, previous studies have …

Hybrid Optical Integrator Based On Silicon-On-Insulator Platform, Taewon Huh

Graduate Theses - Physics and Optical Engineering

A hybrid optical integrator is a recirculating loop that performs oversampling typically for analog input, using the cross-gain modulation (XGM) in a semiconductor optical amplifier (SOA). The modulated input signal changes the gain of the loop through XGM and thus modifies the loop accumulation. This thesis presents hybrid optical integrator for an all-optical analog-to-digital converter based on a silicon photonics platform. The device consists of silicon waveguides of dimension 220 × 500 nm (thick × width) and approximately 5 m optical loop length including fiber length, input and output grating couplers for 1550 nm signal, directional couplers, and external components …

Usu Professor Receives Alumni Award From Virginia Tech | College Of Engineering, Utah State University

College of Engineering News

Utah State University’s Marc Maguire received the Outstanding Young Alumni Award from The Charles E. Via, Jr. Department of Civil and Environmental Engineering at Virginia Tech. Maguire is an assistant professor of civil and environmental engineering.

2014 - Public Update For Drought Response, Groundwater Basins, With Potential Water Shortages And Gaps In Monitoring

Miscellaneous Documents and Reports

A groundwater report as required by Governor's January 17, 2014 Emergency Drought Proclamation (Order Action Number 11) requiring that DWR describe basins with potential water shortages and gaps in groundwater monitoring. Preparing the report entailed compiling and evaluating all available data, including information presented in California Water Plan Update 2013.

Data was compiled and analyzed from the California Statewide Groundwater Elevation Monitoring (CAS GEM) Program, the Water Data Library (WDL) groundwater level database, the draft Bulletin 160 California Water Plan Update 2013, and from well completion reports (driller'S logs) submitted to DWR. The focus of this update was to analyze …

2013 - Discussion Draft - Groundwater Workplan Concept Paper

Miscellaneous Documents and Reports

California work plan that aligns groundwater protection efforts, the ongoing actions of other entities with groundwater management responsibilities, and potential actions that the Water Boards. Effective groundwater management is necessary to ensure groundwater quality and quantity is maintained at sustainable levels that support beneficial uses of water over the long-term.

Injectable, Magnetically Orienting Electrospun Fiber Conduits For Neuron Guidance, Christopher D.L. Johnson, Debmalya Ganguly, Jonathan M. Zuidema, Thomas J. Cardinal, Alexis M. Ziemba, Kathryn R. Kearns, Simon M. Mccarthy, Deanna M. Thompson, Ganpati Ramanath, Diana A. Borca-Tasciuc, Silvio Dutz, Ryan J. Gilbert

Chemical and Biochemical Engineering Faculty Research & Creative Works

Magnetic electro spun fibers are of interest for minimally invasive biomaterial applications that also strive to provide cell guidance. Magnetic electro spun fibers can be injected and then magnetically positioned in situ, and the aligned fiber scaffolds provide consistent topographical guidance to cells. In this study, magnetically responsive aligned poly-l-lactic acid electro spun fiber scaffolds were developed and tested for neural applications. Incorporating oleic acid-coated iron oxide nanoparticles significantly increased neurite outgrowth, reduced the fiber alignment, and increased the surface nano topography of the electro spun fibers. After verifying neuron viability on two-dimensional scaffolds, the system was tested as an …

Structural Transformations During Periodic Deformation Of Low-Porosity Amorphous Materials, Nikolai V. Priezjev, Maxim A. Makeev

Mechanical and Materials Engineering Faculty Publications

Atomistic simulations are employed to study structural evolution of pore ensembles in binary glasses under periodic shear deformation with varied amplitude. The consideration is given to porous systems in the limit of low porosity. The initial ensembles of pores are comprised of multiple pores with small sizes, which are approximately normally distributed. As periodic loading proceeds, the ensembles evolve into configurations with a few large-scale pores and significantly reduced number of small pores. These structural changes are reflected in the skewed shapes of the pore-size distribution functions and the appearance of a distinct peak at large length scales after hundreds …

Failure Mode Identification Of Masonry Infilled Rc Frames, Rabab Allouzi, Ayhan Irfanoglu

Emirates Journal for Engineering Research

This paper presents a new method to identify the ultimate failure mode of reinforced concrete (RC) frames due to the presence of masonry infill walls. The proposed method is based on simple geometry, reinforcement ratios and material properties of the elements involved in the frame-wall assembly. A simple engineering tool, expressed in terms of infill wall-to-RC frame stiffness and strength ratios, is developed to estimate whether the ultimate failure mode that would evolve during strong earthquake ground shaking in the infilled RC frame is brittle or ductile. The brittle failure mode, that is, shear failure in columns, should be avoided …

2014 - State Of The Salinas River Groundwater Basin Report, Executive Summary

Miscellaneous Monterey and San Luis Obispo County Documents and Reports

An examination of the state of the Salinas River Groundwater Basin (Basin) was conducted in the last half of 2014 as part of the larger Basin Investigation. This Executive Summary of the State of the Basin Report addresses the ramifications of prolonged drought by considering likely changes in groundwater head elevations, groundwater storage, and seawater intrusion in the event that the current drought continues. In addition, some steps are presented that could be taken to help alleviate the consequences of further depleting groundwater storage.

Optimizing 3d Printed Prosthetic Hand And Simulator, Stephen Estelle

LMU Theses and Dissertations

The purpose of this study is to examine the position and use of an upper extremity prosthetic simulator on non-amputees. To see how a 3D printed prosthetic simulator can be optimized to serve the user correctly and accurately. In addition, this study examines the improvement of the Hosmer 5X Prosthetic Hook with the addition of newly designed trusses on to the prosthetic, as well as utilizing a new manufacturing method known as 3D printing. These topics are important because there is no standardized prosthetic simulator for schools and research facilities to use. Off the shelf prosthetic simulator cost upwards of …

Application Of Virtual Reality In Rehabilitation Of Special Populations, Tingting Liu, Liu Zhen, Ping'an Qian, Rongrong Xuan, Wang Jin, Yanjie Chai

Journal of System Simulation

Abstract: With the continuous development of urbanization and the trend of population aging, the number of people who need physical and mental rehabilitation continues to increase. Using information technology to assist the rehabilitation process has the important practical significance. The existing studies about the application of virtual reality (VR) technology in the rehabilitation, psychological problems and children with autism for stroke are reviewed. A framework for the intelligent rehabilitation system is proposed. Virtual agent, the technology of somatosensory and voice recognition are advised to be used. Based on the proposed framework, a prototype rehabilitation game for autism and an upper …

A Review Of Rare Event Simulation, Liping Wang, Wenhui Fan

Journal of System Simulation

Abstract: Rare-event has a great significance for its lower probability of occurrence and greater harmfulness, the traditional Monte Carlo method is difficult to analyze it effectively. Rare-event simulation technique which is developed quickly and applied in many areas can sample the rare-event effectively with variance reduction methods and can estimate the occurrence probability of rare-event. The research status of rare-event simulation technique is summarized firstly; the principles, problems and progress of the main methods are analyzed and concluded secondly; after that the application fields of the technique are elaborated and summarized; the future development tendency of rare event simulation technique …

Integrated Modeling For Time Delay Stability Analysis In Gcps, Jianbo Jiang, Li Peng, Aimin Miao, Cao Min, Songhai Zhang, Tan Lei, Kerun Li

Journal of System Simulation

Abstract: According to the separation problems of physical and cyber modeling in time delay stability analysis for grid cyber-physical system (GCPS), an integrated modeling method is presented and proved by single machine infinite bus system (SMIBS). The time delay and stability of GCPS are analyzed and discussed, and the physical and cyber models of SMIBS are established respectively. The dynamic linking library by EA and VS based on information model (CIM) are generated, and the united simulation platform is achieved by MATLAB. The results of the simulation show that the unified structure of information flow …

Parameter Estimation Of Lfmcw Signals Based On Improved Sm Method, Jiang Li, Junni Zhou, Runling Yang, Liu Li

Journal of System Simulation

Abstract: The parameter estimation of linear frequency modulation continuous wave (LFMCW) signal is a research hotspot in electronic reconnaissance systems. In this paper, the time frequency distribution feature of LFMCW signals is studied first. Based on the improved S-method (SM), an algorithm for parameter estimation of LFMCW signals is proposed. It uses short-time Fourier transform (STFT) to calculate the SM with adaptive window width, which can suppress the crossterm interferences and improve the time-frequency resolution. Theoretical analysis and simulation experiment results demonstrate the validity of the proposed algorithm under low SNR.

Research On Method Of Battlefield Situation Representation Based On Multiplex Information Cell, Xiying Huang, Dinghai Zhao, Shao Wei

Journal of System Simulation

Abstract: We adopt the grid-space method to represent the battlefield as discrete cell model. And we construct the multiplex information cell (MIC) using the situation-meta’s information such as position, states collection, indexed by position. The positions of MICs correspond to the battlefield’s positions. Both of them can be represented as stack or data array. This method gives a way to build the whole mapping relationship between data structure which the computer can understand and the battle factors such as position and state of situation-meta. When the position or state of the situation-meta changes, the computer can redraw the view according …

Towards The Automatic Evolution Of Workload Models In Large-Scale Astronomical Data Management, Huajin Wang, Wan Meng, Han Rui, Ren Wei, Haiming Zhang, Jianhui Li

Journal of System Simulation

Abstract: The benchmark's guiding role in system selection/optimization requires its workload model has the ability to: Run on various systems of the target application scenario (be portable); Reflect the typical tasks' characteristics and data access patterns (be representative). The emerging systems and tasks in large-scale astronomical data management field have led workload models constructed by existing methods to be prone to lose portability and representativeness. An automatic evolutionary workload modeling method has been proposed: Abstract operations are used to keep the workload model’s portability; Automatic workload log analytics are used to keep the workload model’s representativeness. The feasibility of this …

Analysis Of Lane Changing Conflict Based On Tta In Expressway Weaving Area, Wang Bao, Linjie Gao, Zhicai Juan

Journal of System Simulation

Abstract: The study of lane changing behavior in expressway weaving area is of great significance to the analysis of the traffic flow conflict and driving behavior characteristics. In this paper, a lane changing conflict model was established and trajectory extraction software was used to extract and calculate TTA (time to avoidance) and TTC (time to collision). We got 336 TTAs and 233 TTCs and 4 grades of the lane changing conflict level were built by using statistical method. We came up with the proposed lane changing speed and some traffic management strategies. The study will help to …

Direct Parameter Identification Method For Steam Turbine And Its Governing System, Jingliang Zhong, Xiaolong Gou, Tongtian Deng

Journal of System Simulation

Abstract: Since most of the traditional parameter identification methods used in the steam turbine and its governing system have the shortages of poor fitness, complicated identification process and long period, a novel identification method based on least square theory, called direct identification method, is proposed in this paper. Parameter to be identified can be obtained quickly and accurately through direct identification method if the identification process is transferred to solve nonlinear equation which represents the minimal error between simulated data and measured data. The identification results show that during identification process the proposed method has high identification efficiency, accurate identification …

Research On Conceptual Model For Trainer Embedded Training System, Jierong Tian, Zhang Li, Han Liang, Cunhu Shi

Journal of System Simulation

Abstract: Embedded training is an effective way to solve the problem of pilot tactical training, and represents a new technique trend in military training. Aiming at the requirements of trainer embedded training, the visual conceptual model that includes case model, static model and dynamic model for trainer embedded training system is constructed by unified modeling language (UML). Based on the conceptual model and the trainer characteristics, with the consideration of the reality and the future development, the structure model of embedded training system is designed referring to foreign architecture of embedded training system. The bus communication of embedded training …

Damage Simulation Of A Certain Type Of Armored Equipment Based On Finite Element Analysis, Junqing Huang, Tuan Wang, Guanghui Li, Fan Rui

Journal of System Simulation

Abstract: Based on the finite element numerical simulation method, the damage simulation of a certain type of armored equipment was studied. The numerical simulation model of ammo power was established. Based on 3D modeling technology, the vulnerability model of the armored equipment in the component level with high-resolution was established. The spatial relation model of projectile and target was established based on the interaction analysis of projectile and target. According to the characteristic of ammo damage element, combined with the damage criterion of armored equipment component, the damage condition of the component and the damage grade of the armored equipment …

Analysis And Optimization For Combat Capability Based On Sequential Simulation Experiment, Chenyan Kong, Zhu Jing, Jiao Song, Shaojie Mao

Journal of System Simulation

Abstract: To deal with the optimization of combat capability, the sequential simulation experiment method was proposed. The simulation evaluation method with precision constraint was used to control the simulation running times. The sensitivity analysis experiment was carried out to identify the important factors affecting the combat capability. The relation model between the important factors and combat capability was constructed via regression analysis experiment. To get the combat capability improvement as large as possible with the price as small as possible, the optimization was used. In the application example, the air-defense combat capability was improved by the method.

Modeling And Simulation For Automobile Connecting Rod Production Line Based On System Dynamics, Li Han, Wenhui Fan, Feng Yuan, Mengni Zhu, Shengxiao Zhang

Journal of System Simulation

Abstract: In the production line system, it is of much significance to assign operation to workstations in order to balance the manufacturing workload and increase productivity under the given constraint conditions. Based on System Dynamics theory, this paper builds a simulation model of a connecting rod production line in an automobile component company. With this model, the paper analyses the balancing rate and influential factors. Then some preliminary optimization is made to improve the production line performance.

Modeling And Simulation Of Connecting Rod Production Line, Yuanyuan Yan, Wenhui Fan, Feng Yuan

Journal of System Simulation

Abstract: Discrete event system simulation method is widely applied to solve various problems, and line balancing problem is also one of them. In this paper, we use discrete event system simulation method to solve line balancing problem. Connecting rod production line is modeled by using DES. A production line model is built and simulated in AnyLogic, the bottleneck process and the problems to be optimized are analyzed. A small program in MATLAB is used to optimize the production line, and find the optimal solution. Simulate again.

Design Of Simulation Platform For Space Operation Mission, Yuan Jing, Jianpin Yuan, Mingming Wang, Wang Fei, Zhang Chi

Journal of System Simulation

Abstract: The design of simulation platform for space mission operations is investigated. The platform has the advantages of high generality and extensibility, being easy to build up new task. FMI (Functional Mockup Interface) standard is adopted to achieve integration of multisource models, and Python scripts are used to realize the task schedule. Unity3D is adopted to implement the visual display system which could display space manipulation process with high fidelity 3D virtual scenes. Configuration tool is developed to map the 3D objects in visual scene with simulation physical variables for complex space control mechanism, which greatly improves the …

Restrain Boundary Effect Of Emd Based On Least Square Fitting, Zhenpeng He, Zhiqi Zhu, Haichao Xie, Yawen Wang, Zongqiang Li, He Rui, Chaoping Du, Jinlan Li

Journal of System Simulation

Abstract: To improve the accuracy of mechanical fault diagnosis, it’s meaningful to do research on the boundary effect of EMD. In this article, least squares linear method is applied to extend local extremum points at the end of a data series, which judges that whether the maximum value is within the wave fluctuation range of the original signal maximum points, whether the minimum value is within the wave fluctuation range of the original signal minimum points. It compares the extended extreme points and endpoint values, so the best signal endpoint is obtained. By calculating the value of similarity coefficient and …

Simulation Research On Post-Earthquake Road Network Repair Schedule Under Dynamic Traffic Flows, Shuanglin Li, Bin Zheng

Journal of System Simulation

Abstract: It is critical to repair the road network immediately to improve the emergency efficiency after earthquake. A mathematics model for post-earthquake road network repair scheduling under dynamic traffic flows (PRNRSDTF) is created and a hybrid genetic algorithm is provided to maximum the cumulative utilities. Finally, in the context of Wenchuan earthquake, a numerical example is abstract from Jingyang district of Deyang City to verify the reliability and validity of the proposed model and algorithm. The normal road network repair scheduling model without considering dynamical traffic flows is taken as a comparison. The results show that the PRNRSDTF model …

Simulated Analysis Of Temporal Robustness For Composite Service, Hengzhou Ye, Taoshen Li, Yunhui Guan

Journal of System Simulation

Abstract: The execution time of a service may fluctuate due to the variety of network, CPU, disk I/O and workloads, which will affect the makespan of the composite service. It is crucial to study the probability distribution and influencing factors of the real makespan to guarantee the performance of the composite service. This paper adopts directed acyclic graph (DAG) to describe the composite service. Also, with the goal of evaluating the variety degree of the makespan, we propose a temporal robustness metric for composition services. Through the rigorous analysis, we can find the boundary of this metric. By the analysis …