Engineering Commons^™

Growth Of Saprophytic And Pathogenic Leptospira: Evaluation Of Medium, Temperature, Inoculum, And Cost, Mary A. Finn, Ronald H. Jones

Biomedical Engineering and Sciences Faculty Publications

Of four media tested, a tissue culture medium supplemented with a bovine serum albumin oleic acid complex provided the best leptospiral growth and cost efficiency.

Darcom Regulation 10-5, Organization And Functions, Us Army Foreign Science And Technology Center, 13 July 1976, Robert Bolin , Depositor

United States Department of Defense Military Intelligence

This is an official document outlining the mission and functions of the Army Foreign Science and Technology Center.

(1) This regulation was included in the Foreign Science the Technology (FSTC) “Unit History, FY 63 to FY 77” dated 1977.

(2) The regulation superceded Army Material Command Regulation 10-5, 11 February 1972.

(3) For a while the Army Materiel Command (AMC) was known as Department of Army Materiel Development & Readiness Command (DARCOM). This was, apparently, a case of changing our name to serve you better. Eventually good sense prevailed and the name reverted to the Army Materiel Command (AMC).

(4) …

An Examination Of The Adaptive Random Search Technique, M. W. Heuckroth, J. L. Gaddy, L. D. Gaines

Chemical and Biochemical Engineering Faculty Research & Creative Works

Random search procedures have recently been successfully applied to the optimization of a variety of chemical engineering problems, including optimization of chemical processes by flow sheet simulation. These procedures represent the independent variables as random variables described by probability distributions. The adaptive random search procedure centers the distribution for each variable about the best search point found and examines this region for a better point. Thus, this technique has the ability of continuously moving the search region toward the optimum, which is particularly advantageous in following constraints. This study examines the efficiency of the adaptive random search technique as applied …

Mass Transfer In Dispersed And Continous Phases For Creeping Flow Of Fluid Spheres Through Power Law Fluids, Türker Gürkan, Robert M. Wellek

Chemical and Biochemical Engineering Faculty Research & Creative Works

The diffusion equation was numerically solved by an implicit finite-difference method for the purpose of calculating the continuous phase Sherwood number, Sh, for mass transfer from an internally circulating Newtonian droplet traveling through a non-Newtonian power-law-type continuous phase in the creeping flow regime. The Mohan stream functions were used in the calculations in order to approximate the velocity profile inside and outside the droplet. The calculated Sh is presented as a function of the Peclet number, Pe, power-law index, n, and a viscosity ratio parameter, X. Sh increases as n decreases in the pseudoplastic region. The dependence of Sh on …

Generalized Correlations For Molecular Weight And Concentration Dependence Of Zero-Shear Viscosity Of High Polymer Solutions., J. L. Zakin, R. Wu, H. Luh, Kenneth G. Mayhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Results of a study are presented which show that two correlations of viscosity-concentration data are useful representations for data over wide ranges of mol. wt and up to at least moderately high concentrations for both good and fair solvents. Low mol. wt polymer solutions (below the critical entanglement mol. wt M//c) generally have higher viscosities than predicted by the correlations. One correlation is eta //s//p/c left bracket eta right bracket versus k prime left bracket eta right bracket c, where eta //s//p is specific viscosity, c is polymer concentration, left bracket eta right bracket is intrinsic viscosity, and k prime …

Predicting Natural Frequencies Of A Hydrodynamically Lubricated Journal Bearing With Constant Oil Supply Pressure, D. C. Edwards, N. Khorzad, Charles L. Edwards

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The analytical and experimental investigations reported here deal with the natural frequencies and system behavior of a full journal bearing subjected to a small sinusoidal load superimposed on a large unidirectional static load. The analysis, verified by experimentation, shows that the bearing can be regarded as two independent second-order systems acting perpendicular to each other. The variable coefficients of the equations of motion cause the bearing to behave as an underdamped system for low values of static eccentricity ratio to, and as an overdamped system for intermediate values of to. The bearing tends to be unstable above a particular to. …

Void-Strengthening In Aluminum And Its Nature, P. G. Manusmare, Hollis P. Leighly

Materials Science and Engineering Faculty Research & Creative Works

Temperature and strain rate dependence of yield strength were used to analyze the nature of aluminum strengthened by the formation of voids. Aluminum rods 99.999% pure were quenched and heat treated to form voids with an approximate density of 1013-1014 voids/cm3. Voids in selected samples were observed by electron microscopy. The yield strength of the void strengthened samples was measured at various temperatures from 77 to 593 K and at two strain rates, 3.33 x 10-2/s and 1.67 x 10-3/s. Tests at room temperature and at 77 K were made at various strain rates. The similarity of Coulomb's approach to …

The Martensite Transformation, Manfred Wuttig, Tetsuro Suzuki

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

A Suboptimal Control Law To Improve The Transient Stability Of Power Systems, Aditya Kumar, Earl F. Richards

Materials Science and Engineering Faculty Research & Creative Works

The application of optimal control theory to damp the electromechanical oscillations associated with the transient conditions in power systems has been given little attention. A suboptimal control law which minimizes the sum of the performance indices of the two linear systems given by a piecewise linear model of a power system improves the transient stability better than the usual "optimal" control law obtained from a linearized model. Further, the suboptimal control law presented in this paper assures stability of the system for all disturbances resulting in rotor oscillations of magnitudes less than a preselected limit. Copyright © 1976 by The …

A High-Accident Spot-Improvement Program, Kenneth R. Agent, John A. Deacon, Robert C. Deen

Kentucky Transportation Center Research Report

As a result of an extensive before-and-after accident study, the high-accident location, spot-improvement program in Kentucky, although not a costly program, was found to have significantly decreased the number of motor vehicle accidents. Favorable benefit-cost ratios indicated that the cost of the program has represented a good investment in comparison with the resultant savings in accident costs. The spot-improvement program had little effect on average accident severity as measured by a severity index. Detailed analysis of available accident data showed that, for studies of the type reported, the 12-month period immediately prior to the date of identification of a high-accident …

A Closed-Form Solution For The Radiosity At The Edge Of A Rectangular Cavity, Alfred L. Crosbie

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

User Oriented Systems Analysis For Regional Municipal Water Supply Planning, Paul E. Pugner, Trevor C. Hughes

Reports

No abstract provided.

An Economic Appraisal Of Reuse Concepts In Regional Water Supply Planning, Rangesan Narayanan, Bartell C. Jensen, A. Bruce Bishop, Kenneth S. Lyon

Reports

Using a conceptual model of a water supply firm, the necessary conditions for production and market efficiency are derived when renovated wastewater is considered as a potential water resource. The nature and extent of the supply augmentation due to recycled reuse is demonstrated using classical optimization techniques. Three stages of short-run supply corresponding to no recycling, partial recycled reuse and complete recycling of all reclaimable water are identified through appropriate Lagrangian Multipliers as well as graphical techniques. A mathematical programming model is structured to determine the optimal water resource allocation and pricing policy for Salt Lake County. By maximizing the …

Management Of The Great Salt Lake: A Research Plan And Strategy, Craig T. Jones, Calvin G. Clyde, J. Paul Riley

Reports

The primary purposes of this report are to indicate the following two research items in connection with the management of the water resource system of the Great Salt Lake:\ 1. Research needs and priorities. 2. A research coordination strategy. Research needs are identified by the report in terms of (1) various management, or use, categories (such as lake industries), and (2) the need to understand the physical characteristics of the lake system itself. The research needs are identified in each category as information (including data) or understanding gaps, in cases where there seems to be sufficient information, a research need …

Capability Of Integer Programming Algorithms In Solving Water Resource Planning Problems, Trevor C. Hughes, William J. Grenney, A. Bruce Bishop, Calvin G. Clyde, Rangesan Narayanan, Paul E. Pugner

Reports

The feasibility of optimizing large regional water resource planning problems by means of integer programming algorithms is analyzed. Two types of integer programming models are developed: (1) A water supply model including 23 separate but geographically related community systems; and (2) a river basin water quality model including 15 point sources of wastewater, 4 types of pollutants, 6 surveillance points, and 7 alternative treatment processes. The water supply model was structured as a mixed integer problem (some continuous variables included) while the water quality model was an all integer problem. Four integer programming algorithms were tested on the sample problems …

Bsam: Basin Simulation Assessment Model Documentation And User Manual, Utah Water Research Laboratory

Reports

No abstract provided.

Disposal Alternatives For Intermittent Sand Filter Scrapings Utilization And Sand Recovery, Jerry T. Elliott, Daniel S. Filip, James H. Reynolds

Reports

A three phase study is used to develop disposal alternatives and cost analysis for algae laden sand scrapings removed from intermittent sand filters used to polish wastewater lagoon effluent. Phase I, Irrigation Technique, explores the feasibility of supplying sufficient water to sand scrapings to leach out entrapped material. Details of removal with amount of water applied are presented. Phase II, Soil Application, tests with lysimeters soil response to application of the algae laden sand material. Physical and chemical parameters are not markedly altered where algae laden sand is applied to the soil surface. Phase III, Plant Bioassays, grew tall fescue …

Evaluation Of The Addition Of Granular Media Filtration To Wastewater Treatment Plants To Meet New Standards, Madhusudan M. Dawda, M. L. Davidson, E. J. Middlebrooks

Reports

A dual media filtration study was carried out at the central Weber Wastewater Treatment Plant in Ogden, Utah, to evaluate its feasibility as a tertiary treatment to meet new effluent quality standards. A review of the literature indicated that dual media filters were more efficient than conventional single media sand filters because of the “in depth” filtration achieved by dual media filters. An experimental filter was operated at four different hydraulic loading rates, ranging from 3 to 6 gpm/ft 2 (122.10 to 244.20 1/min/m2), to evaluate its effects on effluent quality. Hydraulic loading rate was shown not to affect suspended …

Colorado River Basin Modeling Studies: Proceedings Of A Seminar Held At Utah State University Logan , Utah July 16-18, 1975, Calvin G. Clyde, Donna H. Falkenborg, J. Paul Riley

Reports

Preface: Computer modeling is an important and valuable tool for water resources planning and management. In recent years many different modeling approaches and techniques have been developed. Some have been applied in the Colorado River Basin. A brief and incomplete search showed over fifty reports on modeling in the Colorado River Basin alone. The main motivation for this Seminar was the indication that (1) much duplication of effort is occuring among Colorado River modeling studies due to lack of information and (2) much of the knowledge now available on modeling is not being effectively applied to real problems. The overall …

Test 1204: Ford 2600 Diesel 6-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1201: Ford 5600 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1202: Ford 4100 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1209: Case1410 Manual ( David Brown 1410 Synchromesh) Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1208: Ford 3600 Gasoline 6-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1214: Massey-Ferguson Mf 230 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1212: White Field Boss 2-70 Diesel (Also White Farm Equipment 2-70 Diesel) 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1217: Ford 6600 And 6700 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1219: Deutz D 6206 Diesel (Also Deutz-Fahr D 6207 Diesel) 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1216: International 4568 And 4586 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1220: Deutz D 6806 And D 6807 Diesel (Also Deutz-Fahr D 6807 Diesel) 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …