Engineering Commons^™

Computer Simulation Of Three-Dimensional Mechanical Assemblies: Part I - General Formulation, Yong Fang, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In Part I of this paper, a dynamic modeling system for the simulation of three-dimensional mechanical assemblies is presented. With this simulation tool, a designer can interactively create an assembly of mechanical components ready for dynamic analysis. The modeling system presented in this paper include» the derivation of the equations of motion of spatial multi-body systems, and the formulation of the equations to model the associated collision detection and collision responses. Part II of this paper is to introduce the geometry modeling and computer simulation of 3D systems.

A Study Of Fatigue Failure In Superalloys Using Positron Annihilation, D. Hoeckelman, Hollis P. Leighly

Materials Science and Engineering Faculty Research & Creative Works

This study shows there are significant changes occurring in the open volume defect concentration during fatigue cycling as measured by the S parameter. These changes are dependent upon the stress ratio, R = σmin/σmax, the maximum stress, σmax, and the number of fatigue cycles. The decline in the S parameter is due to the elimination of the residual vacancies. This decline is followed by an increase due to the generation of dislocations and the formation of small microcracks. This is followed by a decline in the S parameter due to growth of the microcracks ultimately leading to failure. Copyright © …

Defect Structure Of Y1-Ycaymno3 And La1-Ycaymno3. Ii. Oxidation-Reduction Behavior, J. W. Stevenson, M. M. Nasrallah, Harlan U. Anderson, Don M. Sparlin

Materials Science and Engineering Faculty Research & Creative Works

Electrical conductivity, Seebeck coefficient, and thermogravimetric behavior of compositions in the systems Y_1-yCa_yMnO₃ and Y_1-yCa_yMnO₃ were studied as functions of temperature and ambient oxygen activity in order to determine the mechanism of electrical transport and defect structure. Compositions in Y_1-yCa_yMnO₃ exhibited very slight oxygen activity-dependent behavior as the ambient oxygen activity was reduced. A defect model which includes the thermally excited disproportionation of Mn³⁺ into Mn²⁺ and Mn⁴⁺ pairs was applied to the oxygen-activity-dependent data for La_0.80Ca_0.20MnO_{3 …}

Solid-State Science And Technology: Synthesis And Characterization Of (Ceo2)0.8(Smo1.5)0.2 Thin Films From Polymeric Precursors, C. C. Chen, Harlan U. Anderson, M. M. Nasrallah

Materials Science and Engineering Faculty Research & Creative Works

(CeO₂)_0.8(CSO) has been suggested for solid oxide fuel cell (SOFC) applications, because of its higher electrical conductivity and chemical stability, compared to other ceria-based materials. However, CSO is difficult to densify under conditions compatible with other SOFC components. A thin film synthesis technique has been developed for the fabrication of dense CSO films from precursor solutions at relatively low temperatures. Dense, smooth, and homogeneous films were obtained on Pt, single-crystal Si, and La_0.6Sr_0.4Co_0.2Fe_0.8O₃ (LSCF) substrates by spin-coating a polymeric precursor and subsequent heat-treatment. Crystallization of the film …

The Influence Of Matrix Microstructure, G. M. Vyletel, J. E. Allison, David C. Van Aken

Materials Science and Engineering Faculty Research & Creative Works

The low-cycle and high-cycle fatigue behavior and cyclic response of naturally aged and artificially aged 2219/TiC/15p and unreinforced 2219 Al were investigated utilizing plastic strain-controlled and stress-controlled testing. The cyclic response of both the reinforced and un-reinforced materials was similar for all plastic strain amplitudes tested except that the saturation stress level for the composite was always greater than that of the unreinforced material. The cyclic response of the naturally aged materials exhibited cyclic hardening and, in some cases, cyclic softening, while the cyclic response for the artificially aged materials showed no evidence of either cyclic hardening or softening. The …

Test 1501/3: Same Argon 60 Vdt/Agco Allis 5660 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1497/3: Same Argon 50 Vdt/Agco Allis 5650 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

A Magnetic Suspension System With A Large Angular Range, Colin P. Britcher, Mehran Ghofrani

Mechanical & Aerospace Engineering Faculty Publications

In order to explore and develop technology required for the magnetic suspension of objects over large ranges of orientation, a small-scale laboratory system, the large-angle magnetic suspension test fixture (LAMSTF) has been constructed at NASA Langley Research Center. This apparatus falls into the category of large-gap, actively stabilized magnetic levitation systems. The hardware comprises five conventional electromagnets in a circular arrangement, each driven from a separate bipolar power amplifier. Electromagnet currents are commanded by a digital control system, implemented on a microcomputer, which in turn derives the position and attitude of the suspended element from an infrared optical system. The …

Glow-Discharge Enhanced Permeation Of Oxygen Through Silver, D. Wu, R. A. Outlaw, Robert L. Ash

Mechanical & Aerospace Engineering Faculty Publications

The permeation of oxygen through Ag0.05Zr over the temperature range of 300-650°C under glow-discharge conditions has been studied and compared to the permeation of thermally dissociated molecular oxygen. A low-energy dc glow-discharge in O₂ has been employed which produced approximately 10% atoms. The permeation rate during the glow discharge was found to be much higher (a factor of ∼10) than without the glow discharge. The small fraction of oxygen atoms generated appears to dominate the permeation because of much higher solution probabilities. Below 500°C, the activation energy for the permeation with glow discharge was found to be 15.5 kcal/mol …

Test 1664: John Deere 7600 Powerquad Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Nebraska Summary: S298 Agco Allis 5650, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1667: John Deere 7700 Powershift Diesel 19-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1669: John Deere 7800 Powershift Diesel 19-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1670: John Deere 8570 Powersync Diesel 12 And 24 Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1671: John Deere 8770 Powersync Diesel 12 And 24 Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Computer Simulation Of Three-Dimensional Mechanical Assemblies: Part Ii - Computer Simulation, T. C. Chou, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Computer simulation of the kinematic and dynamic behaviors of mechanical assemblies has become a very important tool in design and manufacturing, because the designer can foresee how a product is going to perform before the product is actually fabricated. However, up to now, the most current simulation modules are based on analysis from another kinematic or dynamic module by specifying the mating conditions between components, and then displaying the motion on the screen. This computer simulation actually performs similarly to a movie and can only provide visual checking. The drawback of this simulation approach is that designers are forced to …

Procase: A Prototype Of Intelligent Case-Based Process Planning System With Simulation Environment, Hao Yang, Wen F. Lu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An intelligent case-based process planning system with interactive graphic simulation environment, PROCASE, is developed lo demonstrate an integrated methodology of case-based process planning system. In PROCASE, both the mechanical part features and the machining operations are represented with a frame-based scheme. PROCASE contains a retriever, a modifier, a simulator and a repairer. It distinguishes itself from traditional rule-based process planning systems by representing the process planning knowledge through previous process planning cases instead of production rules. It therefore can overcome some problems in the traditional rule-based expert systems. PROCASE currently resides in IRIS Indigo workstation. With a user-friendly graphic environment, …

Second Law Analysis Of Active Magnetic Regenerative Hydrogen Liquefiers, L. Zhang, S. A. Sherif, T. N. Veziroglu, John W. Sheffield

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Recent published work in the area of magnetic refrigeration reports on its potential for greater efficiency and high reliability. This paper presents an exergy analysis of a three-stage active magnetic regenerative (AMR) hydrogen liquefier which cools a hydrogen gas stream at 77 K and 1 atm to hydrogen liquid at 20 K. Ortho - para conversion of hydrogen is accomplished in a heat exchanger employing a 10 atm helium fluid that cycles in the refrigerator. The performance of the system is described in terms of the cooling capacity and exergy losses as functions of the magnetic material type, magnetic bed …

Observations On Higher-Order Beam Theory, A. Bhimaraddi, K. Chandrashekhara

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A parabolic shear-deformation beam theory assuming a higher-order variation for axial displacement has been recently presented. In this theory, the axial displacement variation can be selected so that it results in a suitable admissible transverse shear-strain variation across the depth of the beam. This paper examines several transverse shear-strain variations that can go with the aforementioned higher-order theory. Apart from the usual simple parabolic variation, six other shear-strain variations are considered: the sinusoidal variation, cubic, quartic, quintic, and sixth-order polynomials. All these variations for transverse shear-strain satisfy the requirement that the shear strain be zero at the extreme fibers (z …

Nebraska Summary: S171 Massey Ferguson 3075, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S145 Case-Ih 5250, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S144 Case-Ih 5240, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S142 Case-Ih 5220, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Asking Questions To Minimize Errors, Nader H. Bshouty, Sally A. Goldman, Thomas R. Hancock, Sleiman Matar

All Computer Science and Engineering Research

A number of efficient learning algorithms achieve exact identification of an unknown function from some clas using membership and equivalence queries. Using a standard transformation such algorithms can easily be converted to on-line learning algorithms that use membership queries. Under such a transformation the number of equivalence queries made by the query algorithm directly corresponds to the number of mistakes made by the on-line algorithm. In this paper we consider several of the natural classes known to be learnable in this setting, and investigate the minimum number of equivalence queries with accompanying counterexamples (or equivalently the minimum number of mistakes …

Direct Measurements Of The Transport Of Nonequilibrium Electrons In Gold Films With Different Crystal Structures, T. Juhasz, H. E. Elsayed-Ali, G. O. Smith, C. Suárez, W. E. Bron

Electrical & Computer Engineering Faculty Publications

The transport of femtosecond-laser-excited nonequilibrium electrons across polycrystalline and single-crystalline gold films has been investigated through time-of-flight measurements. The thicknesses of the films range from 25 to 400 nm. Ballistic electrons as well as electrons interacting with other electrons and/or with the lattice have been observed. The ballistic component dominates the transport in the thinner films, whereas the interactive transport mechanism is dominant at the upper end of the thickness range. A slower effective velocity of the interactive component is observed in the polycrystalline samples, and is assumed to arise from the presence of grain boundaries. The reflection coefficient of …

Large Capacity Missile Carrier (Cmx), C. N. Calvano, J. M. Berner, J. M. Bradley, K. A. Tosiello, D. T. Hooker, C. F. Merrill

Engineering Management & Systems Engineering Faculty Publications

A systems engineering approach to the development of a radically different kind of surface combatant ship is presented, followed by a preliminary design of the ship shown by the analysis to be most effective. The requirement for the project was the development of a ship which would provide a major increase in the missile firepower of a battlegroup. The study conducts an analysis of four warfare scenarios and evaluates the effectiveness of replacing some Aegis ships with the missile carrier (CMX) and examines the relative utility of varying missile loads for the CMX. An alternative is chosen for further development …

Embankment Widening And Grade Raising On Soft Foundation Soils, Phase 2, Scott Ludlow, Wai-Fah Chen, Philippe L. Bourdeau, C. W. Lovell

JTRP Technical Reports

No abstract provided.

Mathematical Modeling Of The Formation Of Calcareous Deposits On Cathodically Protected Steel In Seawater, J. F. Yan, T. V. Nguyen, Ralph E. White, R. B. Griffin

Faculty Publications

A first principle mathematical model of the formation of calcareous deposits on a cathodically protected steel rotatingdisk electrode in seawater is presented. The model includes equations which transport phenomena, electrochemical reactions,precipitation reactions, and a homogeneous reaction involved in the formation of calcareous deposits on an electrodesurface. Predicted concentration profiles show that a high concentration of OH^– ions on the electrode surface leads to the formation of calcareous deposits. The calcareous deposits contain mostly CaCO₃, but the initial deposits are predicted to contain more Mg(OH)₂ than CaCO₃. The predicted calcareous deposits on the electrode surface …

Parametric Studies Of The Formation Of Calcareous Deposits On Cathodically Protected Steel In Seawater, J. F. Yan, Ralph E. White, R. B. Griffin

Faculty Publications

A first principle mathematical model has been used to study the effects of ocean environment and cathodic protection on the formation of calcareous deposits and their ability to reduce the cathodic current density. These parameters include applied potential, rotation speed, temperature, salinity, and depth. The results showed the applied potential strongly influences the formation of calcareous deposits and their ability to reduce the cathodic current density. Among the environmental factors, rotation speed has the most influence on the cathodic current density. Salinity slightly influences the cathodic current density over the range of interest. Temperature is much more influential than salinity …

A Water And Heat Management Model For Proton-Exchange-Membrane Fuel Cells, Trung V. Nguyen, Ralph E. White

Faculty Publications

Proper water and heat management are essential for obtaining high-power-density performance at high energy efficiency for proton-exchange-membrane fuel cells. A water and heat management model was developed and used to investigate the effectiveness of various humidification designs. The model accounts for water transport across the membrane by electro-osmosis and diffusion, heat transfer from the solid phase to the gas phase and latent heat associated with water evaporation and condensation in the flow channels. Results from the model showed that at high current densities (> 1 A/cm²) ohmic loss in the membrane accounts for a large fraction of the …