Engineering Commons^™

Applicant's Guide To Traffic Impact Studies, Soumya Sekhar Dey, Jon D. Fricker

JTRP Technical Reports

No abstract provided.

Detection And Location Of Pipe Damage By Artificial-Neural-Netprocessed Moire Error Maps, Barry G. Grossman, Frank S. Gonzalez, Joel H. Blatt, Scott Christian Cahall

Electrical Engineering and Computer Science Faculty Publications

A novel automated inspection technique to recognize, locate, and quantify damage is developed. This technique is based on two already existing technologies: video moire metrology and artificial neural networks. Contour maps generated by video moire techniques provide an accurate description of surface structure that can then be automated by means of neutral networks. Artificial neural networks offer an attractive solution to the automated interpretation problem because they can generalize from the learned samples and provide an intelligent response for similar patterns having missing or noisy data. Two dimensional video moire images of pipes with dents of different depths, at several …

Light-Emitting Diodes From Partially Conjugated Poly(P-Phenylene Vinylene), C. Zhang, David Braun, A. J. Heeger

Electrical Engineering

We report the effect of conversion conditions on the device characteristics of poly(p-phenylene vinylene) (PPV) light-emitting diodes. Both electroluminescence and photoluminescence intensities decrease with increasing degree of conversion. Partial conjugation enhances the electroluminescence intensity and gives an efficiency (with Ca as electron-injecting contact) as high as 0.75% photons per electron, about two orders of magnitude more efficient than from similar devices prepared from fully converted PPV. The results of constant current stress measurements suggest that the partially conjugated PPV diode is relatively stable at room temperature.

Effects Of Crosstalk On Fidelity In Page-Oriented Volume Holographic Optical Data Storage, Gregory P. Nordin, P. Asthana

Faculty Publications

Using numerical simulation, we quantitatively examine the effects of cross talk on the recall fidelity of stored binary data in a page-oriented volume holographic memory system. We discuss the trade-off between the signal-to-noise ratio of the reconstructed bits and the optical throughput of the system (i.e., the fraction of the incident beam that is diffracted to the detector plane). We show that significant gains in the signal-to-noise ratio can be achieved with modest decreases in optical throughput in the region where the highest throughput occurs. The magnitude of this trade-off is influenced by both beam degeneracy and coherent recording cross …

Inhibition Of Surface-Related Electrical Breakdown Of Long P+-I-N+ Silicon Structures, F. E. Peterkin, P. F. Williams, B. J. Hankla, L. L. Buresh, S. A. Woodward

P. F. (Paul Frazer) Williams Publications

Semiconductors such as silicon and GaAs appear attractive for use in high voltage devices because of their high bulk dielectric strength. Typically, however, such devices fail at a voltage well below that expected due to a poorly understood, surface-related breakdown process. In this letter we present empirical results which show that such breakdown of long silicon p⁺-i-n⁺ devices can be inhibited by the application of weak visible or near-infrared illumination. These results suggest a technique for avoiding surface flashover in practical high voltage devices, and provide information about the physical mechanisms responsible for initiating …

Measurement Of The Nonsteady Flow Field In The Opening Of A Resonating Cavity Excited By Grazing Flow, Hans R. Graf, William W. Durgin

Office of the Provost Scholarship

Flow past the opening of a cavity can excite acoustic resonance. The periodic velocity field in the region of the cavity opening has been measured for various flow conditions and the vorticity distribution has been computed from the measured data using numerical differentiation. The results indicate that the shear layer rolls up into discreet vortices, which travel across the cavity opening. Two resonances were found. The first is characterized by a single vortex being present and results in the greatest amplitude. The second is characterized by the presence of two vortices which excite a distinct but lesser amplitude resonance. As …

Acuta Enews May 1993, Vol. 22, No. 5

ACUTA Newsletters

In This Issue

Call for Nominations page 2

President's Message page 3

MHEC $aves with Virtual Private Network page 4

Board of Directors Meeting page 5

Tireed Dues page 5

Toll Fraud Takes Aim page 6

Infrastructure page 7

Toll Fraud Checklist page 8

Will My Cellular Phone Fry My Brain? page 9

Executive Director's Message page 11

Analysis Of Laser Pulse Chirping In Mode-Locked Vertical-Cavity Surface-Emitting Lasers, Wenbin Jiang, Dennis J. Derickson, John E. Bowers

Electrical Engineering

Mode-locked vertical cavity lasers have a large cross-sectional area and consequently a large saturation energy and large peak powers. The authors analyze excess optical bandwidth generation in these lasers and find that self-phase modulation due to optical pumping and gain saturation is the dominant factor in inducing laser pulse chirping. The large magnitude of the chirp makes intracavity prism-pair compensation difficult. Adjustment of the cavity length has a major impact on the pulse chirping, as observed experimentally. Proper adjustment can result in a large linear frequency chirp which can be compensated using external pulse compression techniques

Reaction Kinetics Analysis Of Urethane Polymerization To Gelation, B Liu, Hossein Noureddini, J S. Dorsey, Delmar C. Timm

Papers in Molecular Chemistry

A chemical reaction analysis of a thermosetting, urethane resin formulated from a triol and a diisocyanate is reported. Population density distributions of oligomeric molecules, monomer concentration, the cumulative molar concentration of intramolecular bonds, the resin's average molecular weights, and extent of reaction were determined as a function of time. Rate expressions for intermolecular reactions were first order with respect to the concentration of each reactant and were proportional to the functionality of their respective chemical moieties. Rate expressions for intramolecular reactions were first order with respect to the concentration of the reactant and were proportional to the functionality of the …

St. Joseph School Area Neighborhood Housing Project Revitalization Study, Kentucky Library Research Collections

Research Collections

No abstract provided.

Weigh Station Bypassing, Herbert F. Southgate, Joseph D. Crabtree, Jerry G. Pigman, Nikiforos Stamatiadis

Kentucky Transportation Center Research Report

A Study was initiated in May of 1990 to investigate the problem of trucks bypassing or avoiding weigh/enforcement stations in Kentucky. A literature review identified two major studies (Wisconsin and Florida) on the subject, both of which are summarized in this report. In addition, a 1989, limited-scope study of truck bypassing of weigh stations in Kentucky was reviewed and summarized.

The primary data collection effort for this study took place in the fall of 1990, centered around the Simpson County enforcement station on Interstate-55. Three potential bypass routes were identified. Automatic vehicle classification (AVC) and weight-in-motion (WIM) equipment was installed …

Stress Evaluation Of Welded Steel Bridges On Coal-Haul Routes, Theodore Hopwood Ii, Keith J. Hogan, Christopher M. Oberst

Kentucky Transportation Center Research Report

This report describes the procedure developed and being employed to determine and assess live-load stresses in structural members of welded steel bridges on extended· weight coal haul routes. Those bridges are routinely subjected to loads from coal trucks in excess of those permitted on other routes. Those elevated loads may result in high stresses in bridge members. Of principal concern are certain weld details on steel bridges that are susceptible to fatigue cracking when subject to high live-load stresses. Seventeen welded steel bridges on extended-weight coal haul routes have been identified for investigation under this study.

The study test procedure …

Protective Construction With Reinforced Earth, Christopher Y. Tuan

Civil Engineering Faculty Proceedings & Presentations

The objective of this research is to develop a simple analytical method that characterizes plane shock wave propagation through reinforced earth and the dynamic interaction with modular retaining wall panels. The shock wave was initiated as a velocity boundary condition. The exact solution was obtained by the Laplace transform method. A step-by-step design procedure based on the "limit state" concept is proposed. Because of the impulsive nature of ground shock. the maximum response of the wall panel and reinforced soil system depends mainly on the capacity and rate of energy absorption and dissipation of the system. Therefore, the connection between …

Spontaneous Coherent Pulsations In Standing-Wave Laser Oscillators: Stability Criteria For Homogeneous Broadening, Pitak Chenkosol, Lee W. Casperson

Electrical and Computer Engineering Faculty Publications and Presentations

The stability criteria for single-mode standing-wave laser oscillators in the homogeneously broadened limit are reported, and two types of criteria are distinguished. The first type (type 1) corresponds to the minimum value of the threshold parameter for which an infinitesimal perturbation away from steady state grows into an oscillatory solution. A second type (type 2) corresponds to the minimum value of threshold parameter for which large-amplitude oscillations do not decay to the steady-state solution. Undamped pulsations in single-mode homogeneously broadened standing-wave laser oscillators are found to occur at a much higher excitation level than in ring-laser oscillators with homogeneous broadening. …

The Application Of Neural Networks To Optimal Robot Trajectory Planning, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

Interpolation of minimum jerk robot joint trajectories through an arbitrary number of knots is realized using a hardwired neural network. Minimum jerk joint trajectories are desirable for their similarity to human joint movements and their amenability to accurate tracking. The resultant trajectories are numerical rather than analytic functions of time. This application formulates the interpolation problem as a constrained quadratic minimization problem over a continuous joint angle domain and a discrete time domain. Time is discretized according to the robot controller rate. The neuron outputs define the joint angles (one neuron for each discrete value of time) and the Lagrange …

Suboptimal Robot Joint Interpolation Within User-Specified Knot Tolerances, Daniel J. Simon, Can Isik

Electrical and Computer Engineering Faculty Publications

Approximation of a desired robot path can be accomplished by interpolating a curve through a sequence of joint-space knots. A smooth interpolated trajectory can be realized by using trigonometric splines. But, sometimes the joint trajectory is not required to exactly pass through the given knots. The knots may rather be centers of tolerances near which the trajectory is required to pass. In this article, we optimize trigonometric splines through a given set of knots subject to user-specified knot tolerances. The contribution of this article is the straightforward way in which intermediate constraints (i.e., knot angles) are incorporated into the parameter …

Practical Optimization Modeling For Contaminant Plume Management, Richard C. Peralta, Alaa H. Aly

Civil and Environmental Engineering Faculty Publications

Simulation/optimization (S/0) models can be used to greatly speed the process of computing desirable groundwater pumping strategies for plume management. They make the process of computing optimal strategies fairly straightforward and can help minimize the labor and cost of groundwater contaminant clean-up.

Laboratory Study On Properties Of Rubber-Soils, Imtiaz Ahmed

JTRP Technical Reports

The waste tire problem in the United States is of great magnitude and has far reaching environmental and economic implications. This study investigates the feasibility of using tire chips, alone and mixed with soils, as lightweight material in highway embankments . The report contains: synthesis of all available information and results from laboratory testing of tire chips, rubber-Ottawa sand, and rubber-Crosby till. It is found that rubber-sand with chip/mix ratios of 33% or less exhibits excellent engineering properties: easy to compact; low dry density; low compressibility; high strength; and excellent drainage characteristics. On the whole, the rubber-Crosby till mixes do …

Resolution Enhancement Of Spaceborne Scatterometer Data, David G. Long, Perry J. Hardin, Peter T. Whiting

Faculty Publications

A method for generating enhanced resolution radar images of the Earth's surface using spaceborne scatterometry is presented. The technique is based on an image reconstruction technique that takes advantage of the spatial overlap in scatterometer measurements made at different times to provide enhanced imaging resolution. The reconstruction algorithm is described, and the technique is demonstrated using both simulated and actual Seasat-A Scatterometer (SASS) measurements. The technique can also be used with ERS-1 scatterometer data. The SASS-derived images, which have approximately 4-km resolution, illustrate the resolution enhancement capability of the technique, which permits utilization of both historic and contemporary scatterometer data …

Ua66/3/3 Acm/Upe Awards Banquet, Association For Computing Machinery, Upsilon Pi Epsilon

Student Organizations

ACM/UPE awards and initiation banquet program.

Evaluation Of Us Seismic Code Provisions For Asymmetric-Plan Systems, Rakesh K. Goel, Anil K. Chopra

Civil and Environmental Engineering

The effects of plan asymmetry on the earthquake response of code-designed, one-story systems are identified with the objective of evaluating how well these effects are represented by torsional provisions in US building codes. The earthquake-induced deformations and ductility demands on resisting elements of asymmetric-plan systems, are compared with their values if the system plan were symmetric. The presented results demonstrate that the design eccentricity in US building codes should be modified in order to achieve the desirable goal of similar ductility demands on asymmetric-plan and symmetric-plan systems. The design eccentricity should be defined differently depending on the design value of …

A Study Of The Manufacturing Costs Of Grille And Side Screens On John Deere Tractors, John M. Beierschmitt

Graduate Research Papers

The problem discussed in this paper was the development of a process for the manufacture of a new, low cost, quality grille screen that previously had been made on conventional tooling, and now can not be made with the conventional process or tooling. The research comparison in this paper was done to show the financial advantage of this type of tooling.

An Examination Of The Labor Time Of A Robot Weld Cell, Chris S. Conrad

Graduate Research Papers

The purpose of this study was to determine the labor time differential, if any, of a robot weld cell as compared to manual welding methods. Also, the variability of labor time differential between part numbers was to be examined.

The results of the study was intended to assist future investment decision makers in maximizing the return on capital expenditures. It was proposed that the labor time differential determined by this study be applied to the future labor and overhead rates in determining the return on investment for a robotic weld cell purchase. The variability of labor time differential between part …

Introduction To Electrical Engineering And The Art Of Problem Solving: Volume I, P. Frazer Williams

P. F. (Paul Frazer) Williams Publications

These notes were written to accompany a two-semester introductory course in Electrical Engineering. The primary goal of the course is to introduce you to the art of technical problem solving. Conventional Electrical Engineering curricula, in favorable cases at least, produce engineers who are reasonably adept at operating many of the tools important to the field, such as mathematics and circuit analysis. Often, however, these engineers lack skill in choosing which tools to use and in designing a plan of attack to solve problems which are new to them, even though they have all the information and skills needed to fabricate …

Introduction To Electrical Engineering And The Art Of Problem Solving: Volume Ii, P. Frazer Williams

P. F. (Paul Frazer) Williams Publications

These notes were written to accompany a two-semester introductory course in Electrical Engineering. The primary goal of the course is to introduce you to the art of technical problem solving. Conventional Electrical Engineering curricula, in favorable cases at least, produce engineers who are reasonably adept at operating many of the tools important to the field, such as mathematics and circuit analysis. Often, however, these engineers lack skill in choosing which tools to use and in designing a plan of attack to solve problems which are new to them, even though they have all the information and skills needed to fabricate …

Minutes Tractor Test And Power Museum April 14th, 1993, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

Use of tractor test building for museum.

Fred Chase Preliminary Outline For Tractor Test Museum, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

No abstract provided.

Acuta Enews April 1993, Vol. 22, No. 4

ACUTA Newsletters

In This Issue

TQM at Univeristy of Kansas page 2

President's Message page 3

Kent State Meets ADA Requirements page 4

Remembering Dorothy Heinecke page 7

Toll Fraud & Telabuse page 8

NATA Addresses E911 Issue page 9

Executive Director's Message page 11

Electrostatic Positioning Of Droplets In Turbulent Flows (Lstm 375/Te/93), Nihad E. Daidzic, Adrian Melling

Aviation Department Publications

Report LSTM 375/TE/93, Lehrstuhl fuer Stroemungsmechanik Universitaet Erlangen-Nuernberg Cauerstr. 4, 8520 Erlangen Germany.

A Technical Paper On Automated Pouring And The Selection Process Used By One North American Foundry, R. Stanley Weaver

Graduate Research Papers

This report on automated pouring focuses on the selection process used by one North American iron foundry. The problem facing this facility and any operation wishing to implement this technology lies in the number of variables which must be addressed in their quest for a suitable system.