Engineering Commons^™

Analysis Of A Passive Flow Control Device Via Flow Visualization Techniques, Cheryl R. Graham, Shi (Peter) Huang

Aerospace Engineering

This report details an experiment done to verify the effectiveness of a passive flow control system on a two-dimensional bluff body, blunt trailing edge model in controlling wake dimension and Karman vortex sheds. An earlier experiment by Park, et.al.[1] performed analysis via wind tunnel pressure testing and computerized model to determine the ideal proportions of such a tab design and identify the flow properties responsible for the potential drag reduction. To obtain visual verification of the existence of these concepts, a bluff body model proportionally identical to the one used by Park, et.al., was designed and tested in a water …

Interplanetary Gravity Assisted Trajectory Optimizer (Igato), Jason Bryan

Aerospace Engineering

Interplanetary space travel is an extremely complicated endeavor that is severely limited by our current technological advancements. The amount of energy required to transport a spacecraft from one planet to the next, or even further, is extraordinary and in some cases is even impossible given our current propulsive capabilities. Due to these complications, the search for other means of exchanging energy became imperative to future space exploration missions. One particularly powerful method that was discovered, and the most commonly used one, is referred to as planetary gravity assist. In order to plan out multiple gravity assist trajectories, complex and robust …

Autonomous Control Of The Cal Poly Motion Flight Simulator, Andrew M. Anderson

Aerospace Engineering

An autonomous controller for the Cal Poly Motion Flight Simulator was developed such that the simulated Van’s RV-7 flies a standard light aircraft traffic pattern without any human pilot input. First, an autopilot was developed in Simulink to control the aircraft’s altitude, airspeed, and heading independent of each other. The performance of the autopilot has been tested to perform with a response sufficient for precise navigation. A C++ s- function was written as a mission controller that followed a pre-programmed path around a known airport. The aircraft performs a standard left 45 degree entry into the traffic pattern, lands on …

Analysis Of F-104c World's Altitude Record Flight, William J. Day

Aerospace Engineering

No abstract provided.

Design, Fabrication, And Testing Of An Automotive Turbocharger-Based Gas Turbine Engine, John Kyle Thoma, Daniel Shehan, Benjamin Naravage, Jacob Melvin

Aerospace Engineering

A fully-functioning, self-sustaining gas turbine engine was designed and built. The engine was constructed around a Holset HE351 VGT automobile turbocharger, containing compressor and turbine assemblies on a common shaft. Other components of the engine were either purchased or designed and fabricated in-house. During initial testing of the completed engine, the turbocharger, however, was found to have extensive damage to the internal oil seals, and so the project could not be completed as planned. Instead, the combustor design and fabrication was completed for stand-alone testing. The combustion chamber was designed so that the flame tube could be easily changed out …

Alterations Of The Cal Poly Supersonic Wind Tunnel To Increase Accuracy And Prove The Absence Of Shockwaves, Garrett A. Lovell, Hector A. Gonzalez

Aerospace Engineering

The calibration and improvement of the Cal Poly supersonic wind tunnel was performed in order to create a fully functional facility for supersonic testing. While investigating possible shocks present in the wind tunnel, it was discovered that the real concern was not the tunnel but the measurement systems. Both measurement systems, pitot tube and Schlieren, were evaluated and were found to be deficient. The pitot system had so much play in it that it bent backward every time the tunnel was run invalidating the results, and giving false shock data. The Schlieren system was missing one vital component to make …

Cal Poly Flight Test Platform For Instrument Development, Kyle Schaller, Ian Muceus, Aaron Ells

Aerospace Engineering

This report summarizes a six month effort to conceptually design, develop, and build an unmanned aerial vehicle to test a boundary layer data system (BLDS) developed by Dr. Russell Westphal and his team of mechanical engineering senior design students. The project is funded by Edwards Air Force Base and the United States Air Force Research Laboratory. During the first Cal Poly quarter of project work, January 4, 2010 to March 18, 2010, the team completed a conceptual and preliminary design. During the second quarter, March 18, 2010 to June 12, 2010, the team completed the construction and initial flight test …

Improved Computational And Experimental Validation Using Different Turbulence Models, Jay Marcos, David D. Marshall

Aerospace Engineering

This paper will explore the methods and techniques necessary to perform a more accurate CFD validation of experimental results. The methods and techniques used will be validated against experimental wind tunnel data of a 2D high lift airfoil with a 3D engine performed by Georgia Tech Research Institute. Preliminary results showed that computational methods over predict the lift and drag coefficient, while still showing very similar trends in CL and CD. To further improve the preliminary results and the predictive capabilities, different turbulence models will be investigated. Results of this validation will assist in determining the appropriate turbulence models, boundary …

Analysis Of Curvature Effects On Boundary Layer Separation And Turbulence Model Accuracy For Circulation Control Applications, Daniel Wilde

Aerospace Engineering

This set of analyses involves flow separation in high curvature regions with special attention to circulation control implementations. Blown flaps of various shapes designed by Rory Golden for use on the AMELIA, or Advanced Model for Extreme Lift and Improved Aeroacoustics, short takeoff vehicle have exhibited flow separation at locations where flap curvature changes. Investigating this problem, its causes, and potential solutions, I have concluded that the separation is equally a function of the flow simulation turbulence model used, and the geometry of the flap itself. Using Gambit version 11.0.1 for grid generation and Fluent version 6.3.26 for CFD calculations, …

Hybrid Rocket Motor, Zach Arena, Alexander Athougies, Alden Rodulfo

Aerospace Engineering

This project involves the re-design, manufacturing, and testing of the Cal Poly Space System’s 4th iteration of an M-class 98mm hybrid rocket motor. This motor utilizes hydroxyl-terminated polybutadiene as fuel with liquid nitrous oxide as the oxidizer. Modeling and analysis was conducted on a 12 port self-impinging swirl injector and fuel manufacturing to improve performance. Several hot and cold flow tests were conducted to validate the analysis and predict performance values. Test results included two test fires resulting in an average of 212 lbf of thrust for 6 seconds with an Isp of 160 seconds and an average thrust of …

Ground Support Equipment For Northrop Grumman Massive Heat Transfer Experiment, Michael A. Manuel, Christopher J. Sparber, Greg A. Trent

Aerospace Engineering

California Polytechnic State University students designed, built, and certified ground support equipment for the Northrop Grumman Massive Heat Transfer Experiment. The Cal Poly design team built the 10000, 20000, and 30000 assemblies to meet Northrop Grumman requirements. The requirements included interface limitations, design load factors, delivery, and testing specifications. The design process consists of requirements generation, conceptual design, preliminary design, design reviews, manufacturing, and certification. The hardware was successfully completed and is used at the Johnson Space and Kennedy Space Center.

Senior Project: Global Position Determination From Observed Relative Position Of Celestial Bodies, Michael Holmes

Aerospace Engineering

A method was developed to determine the latitude and longitude of an observer based on the observed position of the Moon and several other celestial bodies. The basic principal developed dealt with the proximity of the Moon. Its relative displacement from calculated values was measured using photography by comparison with stars near the Moon. Photographs were taken from a location in San Luis Obispo at Longitude 120°35.9' and Latitude 35°13.3'. The analysis method has determined the location of the observer to a Longitude of 117°43.8'. An additional method located the observer to 36°38.7'N Latitude and 114°47.6'W Longitude.

Conceptual Aircraft Hinge Moment Measurement System, Erin M. Hambrick, Nicole M. Thomason

Aerospace Engineering

The Conceptual Aircraft Hinge Moment Measurement System (CAHMMS) was designed, prototyped, and validated to improve hinge moment estimates early in the design process. Validation was performed by integrating CAHMMS with a test wing and conducting wind tunnel tests to compare the expected theoretical, historical, and Computational Fluid Dynamics (CFD) predictions to the experimental results. As CAHMMS is an external measurement system, interference effects at the connection points were investigated. Further studies were undertaken to verify the CFD predictions with the experimental hinge moment measurements. Hinge moment results from the experimental data and the theoretical data closely correlated with less than …

Rv-7 N675cp Lean Versus Rich Fuel Mixture Aircraft Performance, Edward Spenser Burgos, William Beaman Howe

Aerospace Engineering

The purpose of this experiment was to compare the effects of flying with lean mixture versus rich mixture on aircraft performance. This was done by taking data in the RV-7 N675CP aircraft, RV-7A base aircraft that was built by students at California Polytechnic State University of San Luis Obispo. The RV-7 N675CP contains a Lycoming O-360-A 180 HP engine and fully automated flight data acquisition system. Test flight data indicates the aircraft consumes less fuel, has greater engine exhaust gas temperature (EGT), and possibly increases airspeed with a lean fuel mixture.

Matlab® Gui Visualization Of Classical Orbital Elements, Nancy Teresa Cabrera

Aerospace Engineering

The classical orbital elements of an orbit are eccentricity, angular momentum, inclination, right ascension of ascending node, true anomaly, and argument of perigee. These six parameters define an orbit. Using MATLAB® to model a satellite orbiting Earth in three dimensions, a graphical user interface was created to allow a user to manipulate the orbital elements to desired quantities. In doing so, each parameter’s impact on the orbit is visually displayed. This furthers the understanding of how the parameters are linked to the orbit. When the interface is first opened, the default circular orbit has a range of 20,000 kilometers, an …

Valveless Pulsejet Engine, Cory William Kerr, James Robert Reynolds

Aerospace Engineering

The goal of this project is to build a valveless pulsejet based on the Lady Anne model, known as the Focused Wave Engine VIII Twin Stack. This project has two main goals. The first goal is to design and build the valveless pulsejet. This includes machine work on stainless steel to build the engine, as well as modifying copper tubes to serve as a fuel injection system. The second goal is to build a test stand that allows for accurate data collection of the total thrust being produced by the engine and acts as a fuel injection and ignition system. …

Design, Fabrication, Structural Testing, And Numerical Analysis Of A Small Scale Composite Wing, Jacob David Gaunt, Juan Carlos Flores, Vincent Andrew Perry

Aerospace Engineering

A small scale composite wing based on a design found on an experimental aircraft was designed, constructed, and tested dynamically and statically. The wing was constructed similarly to an experimental aircraft wing. The performed static test was intended to produce pure bending. Strain gages were used to measure strains on the wing structure. The strains were converted to stresses to aid in analysis. The static test results suggested that the wing was actually under torsion. Four structural modes were found from the static test. A finite element analysis model was made to compare experimental results to numerical analytical results. The …

Modified Sequential Kriging Optimization For Multidisciplinary Complex Product Simulation, Wang Hao, Wang Shaoping, Mileta M. Tomovic

Engineering Technology Faculty Publications

Directing to the high cost of computer simulation optimization problem, Kriging surrogate model is widely used to decrease the computation time. Since the sequential Kriging optimization is time consuming, this article extends the expected improvement and put forwards a modified sequential Kriging optimization (MSKO). This method changes the twice optimization problem into once by adding more than one point at the same time. Before re-fitting the Kriging model, the new sample points are verified to ensure that they do not overlap the previous one and the distance between two sample points is not too small. This article presents the double …

Measurement Of Refractive Index Change Of Optical Fiber Core Induced By Femtosecond Laser Scanning, Y. Han, T. Wei, Hai-Lung Tsai, Hai Xiao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We report a new method to measure the refractive index change in optical fiber core induced by femtosecond (fs) laser exposure. An in-line Fabry-Perot interferometer, serving as the measurement platform, is constructed on a commercial single-mode optical fiber by onestep femtosecond (fs) laser fabrication. A positive refractive index change is observed and measured accurately as the laser pulse energy surpasses the ablation threshold.

Observations Of Temporal Group Delays In Slow-Light Multiple Coupled Photonic Crystal Cavities, S. Kocaman, Xiaodong Yang, J. F. Mcmillan, M. B. Yu, D. L. Kwong, C. W. Wong

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We demonstrate temporal group delays in coherently coupled high- Q multicavity photonic crystals, in an all-optical analog to electromagnetically induced transparency. We report deterministic control of the group delay up to 4x the single cavity lifetime in our room-temperature chip. Supported by three-dimensional numerical simulations and theoretical analyses, our multipump beam approach enables control of the multicavity resonances and intercavity phase, in both single and double transparency peaks. The standing-wave wavelength-scale photon localization allows direct scalability for chip-scale optical pulse trapping and coupled-cavity quantum electrodynamics.

Uav Pirates And Silentrack Integration, Travis Dean, Hushnak Singh, Ashley Wager, Matthew (Matt) Woolridge

Electrical Engineering

The integration of the UAV pirating system with the SilenTrack video tracking system will allow the combined system to automatically identify and track a suspicious air vehicle visually as well as identify and decode the RF control signal. Once a threat has been identified, the system will execute an algorithm to associate each control channel with the corresponding flight control surface. Once the control channels have been decoded the user can use a hand held radio controller to maneuver the drone which is now under their command.

Applied System Identification For A Four Wheel Reaction Wheel Platform, Seth F. Silva

Master's Theses

Applied System Identification for a Four Wheel Reaction Wheel Platform

By

Seth Franklyn Silva

At the California Polytechnic State University, San Luis Obispo there is a four-wheel reaction wheel pyramidal simulator platform supported by an air-bearing. This simulator has the current capability to measure the wheel speeds and angular velocity of the platform, and with these measurements, the system identification process was used to obtain the mass properties of this simulator. A handling algorithm was developed to allow wireless data acquisition and command to the spacecraft simulator from a “ground” computer allowing the simulator to be free of induced torques …

Non-Explosive Actuator Simulator, Bryan Costanza

Aerospace Engineering

The CubeSat group at California Polytechnic State University, San Luis Obispo discovered the need for a new piece of ground test equipment. Previous testing of the non-explosive actuator has been very expensive and is not repeatable; two undesirable traits. The analysis of the fuse as well as the design and test of the simulator concept and final article is discussed. The simulator has already seen real use and its entire build and operation cost is much less than the cost of one test of the actual hardware. Performance of the simulator based on burn time and reset time is acceptable …

Cubesat Developers' Workshop 2010, Tracy Owens, Ryan Race

Communication Studies

This project is the narrative component of the 7th Annual CubeSat Developers' Workshop 2010 planning process. It reviews the steps and team dynamics over the seven months spent coordinating the conference for the Aerospace Department. It was the first time that students from the Communcation Studies Department were brought in to help with the event, and the gap between the College of Liberal Arts and the College of Engineering was bridged.

Blended Wing Body Form Factor Code And Model Center Integration, Simone (Simo) Alberti

Aerospace Engineering

This senior project investigated a method of calculating the form factor of an arbitrarily shaped wing, such as a blended wing body, from its pressure coefficient distribution. A Matlab script was coded and integrated into an existing Model Center tool for blended wing bodies. Model Center allows a VSP model to be analyzed with PMARC, a panel code, to determine the pressure distribution over a wing. The Matlab code can then calculate the form factor and critical Mach number. It was found that the code can accurately model simple planar wings, validated against empirical equations, and is robust for blended …

A Design-Build-Test-Fly Project Involving Modeling, Manufacturing, And Testing, Scott Post, Shankar Seetharaman, Sree Abimannan

Publications

This paper describes a junior-level semester-long class project for students in Fluid Mechanics courses. The goals of the project are to introduce students to engineering design, project management, and to incorporate material from other courses in engineering graphics, numerical methods, instrumentation and measurements, and manufacturing processes in a single project. The project focuses on airfoil design using computational tools, and the main emphasis lies on verification of results obtained from computational methods with experimentally measured values. Students will use the airfoil shape they select to make wings to go on a model foam glider. The final part of the project …

Analytic Confusion Matrix Bounds For Fault Detection And Isolation Using A Sum-Of-Squared-Residuals Approach, Daniel J. Simon, Donald L. Simon

Electrical and Computer Engineering Faculty Publications

Given a system which can fail in 1 of n different ways, a fault detection and isolation (FDI) algorithm uses sensor data to determine which fault is the most likely to have occurred. The effectiveness of an FDI algorithm can be quantified by a confusion matrix, also called a diagnosis probability matrix, which indicates the probability that each fault is isolated given that each fault has occurred. Confusion matrices are often generated with simulation data, particularly for complex systems. In this paper, we perform FDI using sum-of-squared residuals (SSRs). We assume that the sensor residuals are s-independent and Gaussian, which …

Development Of A Meshless Method To Solve Compressible Potential Flows, Alejandro Ramos

Master's Theses

The utility of computational fluid dynamics (CFD) for solving problems of engineering interest has experienced rapid growth due to the improvements in both memory capacity and processing speed of computers. While the capability now exists for the solution of the Navier-Stokes equations about complex and complete aircraft configurations, the bottleneck within the process is the time consuming task of properly generating a mesh that can accurately solve the governing partial differential equations (PDEs). This thesis explored two numerical techniques that attempt to circumvent the difficulty associated with the meshing process by solving a simplified form of the continuity equation within …

A Three Dimensional Vortex Particle-Panel Code For Modeling Propeller-Airframe Interaction, Jacob S. Calabretta

Master's Theses

Analysis of the aerodynamic effects of a propeller flowfield on bodies downstream of the propeller is a complex task. These interaction effects can have serious repercussions for many aspects of the vehicle, including drag changes resulting in larger power requirements, stability changes resulting in adjustments to stabilizer sizing, and lift changes requiring wing planform adjustments.

Historically it has been difficult to accurately account for these effects at any stage during the design process. More recently methods using Euler solvers have been developed that capture interference effects well, although they don't provide an ideal tool for early stages of aircraft design, …

Numerical Examination Of Flow Field Characteristics And Fabri Choking Of 2d Supersonic Ejectors, Brett G. Morham

Master's Theses

An automated computer simulation of the two-dimensional planar Cal Poly Supersonic Ejector test rig is developed. The purpose of the simulation is to identify the operating conditions which produce the saturated, Fabri choke and Fabri block aerodynamic flow patterns. The effect of primary to secondary stagnation pressure ratio on the efficiency of the ejector operation is measured using the entrainment ratio which is the secondary to primary mass flow ratio.

The primary flow of the ejector is supersonic and the secondary (entrained) stream enters the ejector at various velocities at or below Mach 1. The primary and secondary streams are …