Engineering Commons^™

Elementary And Middle School Science Lesson Plan: Solid, Liquid, Gas, What Is It?, Getaway Special Team 2010

Education and Outreach

No abstract provided.

Uncertainty Quantification Integrated To Cfd Modeling Of Synthetic Jet Actuators, Srikanth Adya, Daoru Frank Han, Serhat Hosder

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Point-Collocation Non-intrusive Polynomial Chaos (NIPC) method has been applied to a stochastic synthetic jet actuator problem used as one of the test cases in the CFDVAL2004 workshop to demonstrate the integration of computationally efficient uncertainty quantification to the high-fidelity CFD modeling of synthetic jet actuators. The test case included the simulation of an actuator generating a synthetic jet issued into quiescent air. The Point-Collocation NIPC method is used to quantify the uncertainty in the long-time averaged u and v-velocities at several locations in the flow field due to the uniformly distributed uncertainty introduced in the amplitude and frequency of …

Parameter Estimation Of Fundamental Technical Aircraft Information Applied To Aircraft Performance, Michael Vallone

Master's Theses

Inverse problems can be applied to aircraft in many areas. One of the disciplines within the aerospace industry with the most openly published data is in the area of aircraft performance. Many aircraft manufacturers publish performance claims, flight manuals and Standard Aircraft Characteristics (SAC) charts without any mention of the more fundamental technical information of the drag and engine data. With accurate tools, generalized aircraft models and a few curve-fitting techniques, it is possible to evaluate vehicle performance and estimate the drag, thrust and fuel consumption (TSFC) with some accuracy. This thesis is intended to research the use of aircraft …

An Investigation Of Damage Arrestment Devices Application With Fastener/Hole Interaction, Richard Vincent S. Balatbat

Master's Theses

This thesis presents a parametric study on the effects of how damage arrestment devices application interacts with a fastener in a composite sandwich panel. The primary objective of the damage arrestment device was to prevent the failure of the composite face sheet, such as crack propagation, around the hole/fastener joint. The damage arrestment devices are made of composite strips that are inserted under the face sheet to increase the overall structural strength of the panel and to prevent the propagation of failure along the hole. This was supposed to be a quicker and stronger alternative to potted inserts for composite …

Stochastic Optimal Control In Nonlinear Systems, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Stochastic control is an important area of research in engineering systems that undergo disturbances. Controlling individual states in such systems is critical. The present investigation is concerned with the application of the stochastic optimal control strategy developed by To (2010) and its implementation as well as providing computed results of linear and nonlinear systems under stationary and nonstationary random excitations. In the strategy the feedback matrix is designed based on the achievement of the objectives for individual states in the system through the application of the Lyapunov equation for the system. Each diagonal element in the gain or associated gain …

"Pull-In" Of A Pre-Stressed Thin Film By An Electrostatic Potential: A 1-D Rectangular Bridge And A 2-D Circular Diaphragm, Gang Duan, Kai Tak Wan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A one-dimensional (1-D) rectangular pre-stressed thin film clamped at two opposite ends is actuated by an electrostatic voltage applied to a pad directly underneath. the pre-stress is allowed to be either tensile or compressive in nature. at a critical applied voltage, the film becomes unstable and makes direct contact with the pad, leading to "pull-in". an elastic model is constructed to account for the phenomenon over ranges of film pad gap and residual stress. the results compare favorably with finite element analysis (FEA) in literature and experimental data and possess distinct advantages over other available closed-form solutions. the model is …

Development Of A Small And Inexpensive Terrain Avoidance System For An Unmanned Aerial Vehicle Via Potential Function Guidance Algorithm, Shane Alan Wallace

Master's Theses

Despite the first unmanned aerial vehicle (UAV) mission being flown on Aug 22 1849 to bomb Venice UAVs have only recently began to modernize into sophisticated tools beyond simple aerial vehicles. With an increasing number of potential applications, such as cargo delivery, communications, search and rescue, law enforcement, and homeland security, the need for appropriate UAV technology advancement also arose. Here, the development of a low-cost collision avoidance system is described. Hardware was tested and selected based on predetermined constraints and goals. Additionally, a variety of potential functions were explored and assessed at their effectiveness in preventing a collision of …

Morehead State University Space Science Center: A Vision For The Future, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Professor Bob Twiggs titled "Morehead State University Space Science Center: A Vision for the Future" from August 30, 2010.

Analytic Treatment Of Vortex States In Cylindrical Superconductors In Applied Axial Magnetic Field, Andrei Ludu, J. Van Deun, M. V, Milosevic, A. Cuyt, F. M. Peeters

Publications

We solve the linear Ginzburg–Landau GL equation in the presence of a uniform magnetic field with cylindrical symmetry and we find analytic expressions for the eigenfunctions in terms of the confluent hypergeometric functions. The discrete spectrum results from an implicit equation associated to the boundary conditions and it is resolved in analytic form using the continued fractions formalism. We study the dependence of the spectrum and the eigenfunctions on the sample size and the surface conditions for solid and hollow cylindrical superconductors. Finally, the solutions of the nonlinear GL formalism are constructed as expansions in the linear GL eigenfunction basis …

Long-Range Pollution Transport During The Milagro-2006 Campaign: A Case Study Of A Major Mexico City Outflow Event Using Free-Floating Altitude-Controlled Balloons, P. B. Voss, R. A. Zaveri, F. M. Flocke, H. Mao, T. P. Hartley, P. Deamicis, I. Deonandan, G. Contreras-Jiménez, O. Martínez-Antonio, M. Figueroa Estrada, D. Greenberg, T. L. Campos, A. J. Weinheimer, D. J. Knapp, D. D. Montzka, J. D. Crounse, P. O. Wennberg, E. Apel, S. Madronich, B. De Foy

Engineering: Faculty Publications

One of the major objectives of the Megacities Initiative: Local And Global Research Observations (MILAGRO-2006) campaign was to investigate the long-range transport of polluted Mexico City Metropolitan Area (MCMA) outflow and determine its downwind impacts on air quality and climate. Six research aircraft, including the National Center for Atmospheric Research (NCAR) C-130, made extensive chemical, aerosol, and radiation measurements above MCMA and more than 1000 km downwind in order to characterize the evolution of the outflow as it aged and dispersed over the Mesa Alta, Sierra Madre Oriental, Coastal Plain, and Gulf of Mexico. As part of this effort, free-floating …

Development Of Measurement Methods For Application To A Wind Tunnel Test Of An Advanced Transport Model, Robert S. Ehrmann

Master's Theses

California Polytechnic State University, San Luis Obispo is currently working towards developing a Computational Fluid Dynamics (CFD) database for future code validation efforts. Cal Poly will complete a wind tunnel test on the Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA) in the National Full-Scale Aerodynamics Complex (NFAC) 40 foot by 80 foot wind tunnel at NASA Ames Research Center in the summer of 2011. The development of two measurement techniques is discussed in this work, both with the objective of making measurements on AMELIA for CFD validation.

First, the work on the application of the Fringe-Imaging Skin Friction …

Picasso Interface For Horizon Simulation Framework, Brian E. Kirkpatrick

Master's Theses

The Horizon Simulation Framework, or HSF, is a modeling and simulation framework compiled from C/C++ source code into a command line program. Picasso is an interface designed to control the input files to Horizon by providing visual tools to create and manipulate the XML files used to define an HSF system of assets, their environment, and other simulation parameters. Picasso also supports the visualization of Horizon output in several different forms, and import mechanics from online space object catalogues.

Implementation Of A Conrad Probe On A Boundary Layer Measurement System, Charles Rocky Ulk

Master's Theses

This thesis presents the design, calibration, and performance evaluation of a type of two-hole pressure probe anemometer known as a Conrad probe, as well as its subsequent implementation on an autonomous, compact boundary layer measurement device and its first application for subsonic in-flight measurements of a swept wing boundary layer. Calibration of the Conrad probe was accomplished using two calibration functions and a non-nulling method for resolving in-plane flow velocity direction and magnitude over a range of ±30 degrees. This approach to calibration and application offered the advantages of rapid data acquisition with lower energy consumption than alternative methods for …

Kalman Filtering With State Constraints: A Survey Of Linear And Nonlinear Algorithms, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

The Kalman filter is the minimum-variance state estimator for linear dynamic systems with Gaussian noise. Even if the noise is non-Gaussian, the Kalman filter is the best linear estimator. For nonlinear systems it is not possible, in general, to derive the optimal state estimator in closed form, but various modifications of the Kalman filter can be used to estimate the state. These modifications include the extended Kalman filter, the unscented Kalman filter, and the particle filter. Although the Kalman filter and its modifications are powerful tools for state estimation, we might have information about a system that the Kalman filter …

Three-Body Abrasion Testing Using Lunar Dust Simulants To Evaluate Surface System Materials, Ryan L. Kobrick, Kenneth G. Budinski, Kenneth W. Street Jr., David M. Klaus

Publications

Numerous unexpected operational issues relating to the abrasive nature of lunar dust, such as scratched visors and spacesuit pressure seal leaks, were encountered during the Apollo missions. To avoid reoccurrence of these unexpected detrimental equipment problems on future missions to the Moon, a series of two- and three-body abrasion tests were developed and conducted in order to begin rigorously characterizing the effect of lunar dust abrasiveness on candidate surface system materials. Two-body scratch tests were initially performed to examine fundamental interactions of a single particle on a flat surface. These simple and robust tests were used to establish standardized measurement …

Investigations Of Femtosecond-Nanosecond Dual-Beam Laser Ablation Of Dielectrics, Cheng Hsiang Lin, Zheng Hua Rao, Lan Jiang, Wu Jung Tsai, Ping Han Wu, Chih Wei Chien, Shean Jen Chen, Hai Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We have conducted experimental investigations for the micromachining of dielectrics (fused silica) using an integrated femtosecond (is) and nanosecond (ns) dual-beam laser system at different time delays between the fs and ns pulses. We found that the maximum ablation enhancement occurs when the fs pulse is shot near the peak of the ns pulse envelope. Enhancements up to 13.4 times in ablation depth and 50.7 times in the amount of material removal were obtained, as compared to fs laser ablation alone. the fs pulse increases the free electron density and changes the optical properties of fused silica to have metallic …

Extension To Multiple Species Of A Two-Equation Turbulence Model For High Speed Flows, Martin Horvath

Master's Theses - Daytona Beach

The Wilcox (2006) k-co turbulence model has been extended to multiple species and implemented in a CFD code for high speed flows using the Steger-Warming flux-vector splitting scheme. The model was chosen because compressibility corrections are not required, nor are viscous damping factors or wall functions to produce the law of the wall, and it has previously been validated for approximately one hundred test cases ranging from incompressible to hypersonic flow regimes. Initial validation cases using first-order accuracy have been performed, including a Mach 2.5 flow past a backward-facing step and a Mach 2.85 flow into a 24° compression corner. …

Uncertainty Quantification Integrated To The Cfd Modeling Of Synthetic Jet Actuators, Srikanth Adya, Daoru Frank Han, Serhat Hosder

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Point Collocation Non-Intrusive Polynomial Chaos (NIPC) method has been applied to two stochastic synthetic jet actuator problems used as test cases in the CFDVAL2004 workshop to demonstrate the integration of computationally efficient uncertainty quantification to the high-fidelity CFD modeling of synthetic jet actuators. In Case1 where the synthetic jet is issued into quiescent air, the NIPC method is used to quantify the uncertainty in the long-time averaged u and v-velocities at several locations in the flow field, due to the uniformly distributed uncertainty introduced in the amplitude and frequency of the oscillation of the piezo-electric membrane. Fifth order NIPC …

Scan Loss Pattern Synthesis For Adaptive Array Ground Stations, William C. Barott, Mary Ann Ingram, Paul G. Steffes

Publications

We present several techniques for maximizing the contact time between low Earth orbiting satellites (LEOs) and a ground station (GS). The GS comprises an adaptive array of electronically steered space-fed lenses (SFLs). Each SFL is manufactured as a low-cost printed circuit with the result that it exhibits scanning loss. By differently orienting the boresights of the SFLs in the adaptive array, the SFL's scanning losses can be made to optimally complement the path loss of the LEO, thereby reducing the cost of the GS while maximizing the download capacity of the satellite link. The optimization, implemented with a genetic algorithm …

Repeating Ground Track Design For Low Earth Orbit Satellite, Gurkan Gurdal

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, conditions and design requirements for a repeating ground track for a low Earth orbit satellite have been examined and several repeating ground tracks have been designed for a single area on the Earth. In order to construct and validate desired orbital results, the study has two phases which also help to investigate repeating ground track conditions: the fist one is the design phase, and second one is the simulation phase. The common objective of all the case studies is to present a closed ground track on the target by using the design parameters. In order to design …

Analytic Construction Of Periodic Orbits In The Restricted Three-Body Problem, Mohammed A. Ghazy

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation explores the analytical solution properties surrounding a nominal periodic orbit in two different planes, the plane of motion of the two primaries and a plane perpendicular to the line joining the two primaries, in the circular restricted three-body problem. Assuming motion can be maintained in the plane and motion of the third body is circular, Jacobi's integral equation can be analytically integrated, yielding a closed-form expression for the period and path expressed with elliptic integral and elliptic function theory. In this case, the third body traverses a circular path with nonuniform speed. In a strict sense, the in-plane …

The Effect Of Systematic Error In Forced Oscillation Wind Tunnel Test Apparatuses On Determining Nonlinear Unsteady Aerodynamic Stability Derivatives, Brianne Y. Williams

Mechanical & Aerospace Engineering Theses & Dissertations

One of the basic problems of flight dynamics is the formulation of aerodynamic forces and moments acting on an aircraft in arbitrary motion. Classically conventional stability derivatives are used for the representation of aerodynamic loads in the aircraft equations of motion. However, for modern aircraft with highly nonlinear and unsteady aerodynamic characteristics undergoing maneuvers at high angle of attack and/or angular rates the conventional stability derivative model is no longer valid. Attempts to formulate aerodynamic model equations with unsteady terms are based on several different wind tunnel techniques: for example, captive, wind tunnel single degree-of-freedom, and wind tunnel free-flying techniques. …

Validating Module Heuristics On Large Scale Products, Rachel Day, Robert B. Stone, Katie Grantham Lough

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Decreasing time and costs is a major objective in many businesses today. Including modularity in the early design phases can effectively decrease time spent on and costs associated with a project. the task of identifying modules within a product early in the design process (when decisions are less expensive) is made less daunting by using the techniques of functional modeling and module heuristics. This paper discusses the results of the initial efforts to verify the module heuristics on large products (products with functional models consisting of more than 30 sub-functions) since the module heuristics were originally developed on small products. …

Functioncad: A Functional Modeling Application Based On The Function Design Framework, Robert L. Nagel, Kenneth L. Perry, Robert B. Stone, Daniel A. Mcadams

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a functional modeling application, Function CAD, based on integrated functional and process modeling within the Function Design Framework. Function CAD provides for mixed, hierarchical models of environment, process and function with relationships represented via flows of material, energy and signal. This paper discusses the technical details of the Function CAD software including its two major components: (1) the library, libFCAD, for handling the internal representation of the model and (2) the GUI for user-Based model manipulation and visualization. the application of Function CAD within a computational, function- based conceptual design process is discussed along with the plugin …

Prediction Of The Transport Properties Of A Polyatomic Gas, Zhi Liang, Hai-Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An Ab Initio Molecular Potential Model is Employed in This Paper to Show its Excellent Predictability for the Transport Properties of a Polyatomic Gas from Molecular Dynamics Simulations. a Quantum Mechanical Treatment of Molecular Vibrational Energies is Included in the Green and Kubo Integral Formulas for the Calculation of the Thermal Conductivity by the Metropolis Monte Carlo Method. using CO2 Gas as an Example, the Fluid Transport Properties in the Temperature Range of 300-1000 K Are Calculated Without using Any Experimental Data. the Accuracy of the Calculated Transport Properties is Significantly Improved by the Present Model, Especially for the Thermal …

A Natural Language To Component Term Methodology: Towards A Form Based Concept Generation Tool, Matt Robert Bohm, Robert B. Stone

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Over the last few decades design researchers have put forward theories and proposed methodologies that increase the chance that a design team will reliably arrive at the optimal solution to a given design problem. Studies, however, bear out that theories and methodologies alone will not guarantee an optimal or even good design solution. Instead, a breadth of knowledge across multiple engineering domains and the time and tools to thoroughly evaluate the design space are as important as any prescriptive design method. This work presents one of the underlying engineering technologies needed to leverage artificial intelligence approaches to thoroughly search the …

An Integrity Framework For Image-Based Navigation Systems, Craig D. Larson

Theses and Dissertations

This work first examines fundamental differences between measurement models established for GPS and those of proposed image-based navigation systems. In contrast to single value per satellite GPS pseudorange measurements, image measurements are inherently angle-based and represent pixel coordinate pairs for each mapped target. Thus, in the image-based case, special consideration must be given to the units of the transformations between the states and measurements, and also to the fact that multiple rows of the observation matrix relate to particular error states. An algorithm is developed to instantiate a framework for image-based integrity analogous to that of GPS RAIM. The algorithm …

A Photogrammetry-Based Hybrid System For Dynamic Tracking And Measurement, Daniel P. Magree

Theses and Dissertations

Noncontact measurements of lightweight flexible aerospace structures present several challenges. Objects are usually mounted on a test stand because current noncontact measurement techniques require that the net motion of the object be zero. However, it is often desirable to take measurements of the object under operational conditions, and in the case of miniature aerial vehicles (MAVs) and deploying space structures, the test article will undergo significant translational motion. This thesis describes a hybrid noncontact measurement system which will enable measurement of structural kinematics of an object freely moving about a volume. By using a real-time videogrammetry system, a set of …

Velocity Plume Profiles For Hall Thrusters Using Laser Diagnostic, Daniel B. Lee

Theses and Dissertations

This research built a non-intrusive laser diagnostic tool using Laser Induced Fluorescence (LIF) and absorption techniques to measure the velocity and density plume profiles of low powered Hall thrusters. This tool was then applied to a Busek 200W Hall thruster to validate the performance against previous research on the same thruster. A laser frequency sweep through 834.72 nm produced LIF signals for ionized xenon –collected at 541.9 nm – in the thruster plume and absorption data outside the plume at a neutral transition at 834.68 nm. The absorption data provided a baseline reference to calculate the axial and radially velocity …

Matlab Structural Analysis Code For String Wing Box Structure, Sean Brown

Aerospace Engineering

This report outlines the method used for analysis of a wing box structure for the experimental “stringy” wing structure often used in light RC aircraft. This code is able to find the displacement of each joint, and the stress and forces in each member of the truss structure. It also has the features of load and structure visualization, Kevlar string removal, user-defined point and distributed loading functions, and user-defined failure criteria function. This method and resulting code is meant for use in the support of the Human Powered Helicopter project being undertaken by the Aerospace and Mechanical Engineering Department at …