Engineering Commons^™

Analysis And Modeling Of An Airport Departure Process, Joseph E. Hebert

Theses and Dissertations

This study analyzes departure delays at a major airport using probability models to represent this non-homogeneous process. The models developed in this study expand on the Markovian models presently used by employing the method of stages to represent some of the model processes. This technique improves the user's ability to achieve a close fit for the service time probability distribution while maintaining the advantages of the Markovian model. The three types of models developed and compared all assume a Markovian system entry process. The first model uses an exponential distribution to model the service process. The second uses an Erlang …

Multipoint Quadratic Approximation For Numerical Optimization, Michael A. Blaylock

Theses and Dissertations

A quadratic approximation for nonlinear functions is developed in order to realize computational savings in solving numerical optimization problems. Function and gradient information accumulated from multiple design points during the iteration history is used in estimating the Hessian matrix. The approximate Hessian matrix is the available for a second order Taylor series approximation to the functions of interest. Several truss and frame models will be used to demonstrate the effectiveness of the new Multipoint Quadratic Approximation (MQA) in solving structural optimization problems.

Fuzzy Logic In Restructurable Flight Control Systems, S. N. Balakrishnan, H. S. Ho

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this paper, a fuzzy logic controller (FLC) is proposed for restructurable flight control systems. The role of the FLC is to stabilize the aircraft upon a fault occurrence. The FLC derives pitch/roll/yaw controls from a generic knowledge base characterized by 49 if-then rules. A linearized model representative of a modern jet fighter provides the basis for the numerical simulation. Simulated faults include various degrees of surface loss at the right stabilator, combined with reduced ailerons and rudder control power. The FLC accomplishes the stabilization task under test conditions without any knowledge of the system parameters. The numerical results demonstrate …

Intercomparison Between Commercial Condensation Nucleus Counters And An Alternating Temperature Gradient Cloud Chamber, Darryl J. Alofs, C. K. Lutrus, Donald E. Hagen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Three Commercial CNC Counters (TSI Models 3010, 3022A, and 3025A) Are Compared with an Alternating Temperature Gradient Cloud Chamber (ALGR). Electrically Size Classified Aerosols of Sodium Chloride and Silver Are Used. Diffusional Losses within the ALGR Are Much Larger Than for the TSI Instruments: Therefore the ALGR Concentrations Are Corrected for Internal Diffusional Losses, But the TSI Instruments Are Not. the Particle Size Range Tested is 4–90 Nm. for Sodium Chloride, the TSI Concentrations Agreed Fairly Well with the Corrected ALGR at Larger Sizes, and Were Below the Corrected ALGR at Smaller Sizes. the Electrical Aerosol Classifier (EAC) Setting at …

On A Method For Obtaining Approximate Solutions To Sturm-Liouville Problems, Serge Abrate

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A method presented recently to find approximate solutions to a Sturm-Liouville problem is shown to be a special case of a classical weighted residual method. The choice of approximation functions and convergence of the method are also examined. © 1995 American Mathematical Society.

Thermal Contact Conductance Of Ceramic Substrate Junctions, K. C. Chung, H. K. Benson, John W. Sheffield

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Adaptive Critic Based Neural Networks For Control (Low Order System Applications), S. N. Balakrishnan, Victor Biega

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Dynamic programming is an exact method of determining optimal control for a discretized system. Unfortunately, for nonlinear systems the computations necessary with this method become prohibitive. This study investigates the use of adaptive neural networks that utilize dynamic programming methodology to develop near optimal control laws. First, a one dimensional infinite horizon problem is examined. Problems involving cost functions with final state constraints are considered for one dimensional linear and nonlinear systems. A two dimensional linear problem is also investigated. In addition to these examples, an example of the corrective capabilities of critics is shown. Synthesis of the networks in …

Hamiltonian Based Adaptive Critics For Aircraft Control, S. N. Balakrishnan, Jie Shen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Aircraft designs are becoming more complex in order to either operate more efficiently as in the commercial sector or to push the performance envelopes as in the military sector. An interesting outcome of this scenario is that `control'' has come to play an important role in helping realize these objectives. Increasingly, control is becoming an integral part of an aircraft design rather than an afterthought. More effective and efficient control of an aircraft is certain to lead to improved performance at a lower cost

On The Use Of Students For Developing Engineering Laboratories, Bopaya Bidanda, Richard E. Billo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper describes a unique and innovative approach that solved the dual problem of starting up a new engineering instructional laboratory in a timely manner, and for teaching engineering students advanced skills in Automatic Data Collection. Students enrolled in a special pilot course were used to develop and startup an Automatic Data Collection laboratory. These students were assigned individual Automatic Data Collection technologies of interest and given total responsibility for the successful startup of the laboratory. The organization and structure of the course modeled the typical team oriented project development efforts in industry. Feedback from students showed the course to …

System Modeling And Control Of Smart Structures, Frank J. Kern, Leslie Robert Koval, K. Chandrashekhara, Vittal S. Rao

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents multidisciplinary research and curriculum efforts at the University of Missouri-Rolla in the smart structures area. The primary objective of our project is to integrate research results with curriculum development for the benefit of students in electrical, and mechanical and aerospace engineering and engineering mechanics. The approach to the accomplishment of curriculum objectives is the development of a two-course sequence in the smart structures area with an integrated laboratory. The research portion of the project addresses structural identification and robust control methods for smart structures. A brief summary of the research results and a description of curriculum development …

Static And Dynamic Characteristics Of Spot Welded Sheet Metal Beams, K. Pal, Don L. Cronin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Although widely employed as structural components in the auto industry, spot welded sheet metal beams manifest static and dynamic behavior that is not well characterized. For the present study, sample beams of three representative cross-sections—hat, box and box with partition—were fabricated of sheet steel. The spacing between the spot welds that hold these sections together was varied from 25.4 mm (1 in.) to 203.2 mm (8 in.) using a 25.4 mm (1 in.) increment. The beams were subjected to static bending and static torsion tests, and bending and torsional stiffnesses were determined as functions of spot weld spacing. The beams …

Improved Finite Element Modeling Of The Turbofan Engine Inlet Radiation Problem, I. Danda Roy, Walter Eversman

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Improvements have been made in the finite element model of the acoustic radiated field from a turbofan engine inlet in the presence of a mean flow. The problem of acoustic radiation from a turbofan engine inlet is difficult to model numerically because of the large domain and high frequencies involved. A numerical model with conventional finite elements in the near field and wave envelope elements in the far field has been constructed. By employing an irrotational mean flow assumption, both the mean flow and the acoustic perturbation problem have been posed in an axisymmetric formulation in terms of the velocity …

Vibration Of Point-Supported Rectangular Composite Plates, Serge Abrate

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A general approach is presented to study the free vibrations of rectangular symmetrically laminated composite plates with point supports by using the Rayleigh-Ritz method and the Lagrange multiplier technique for enforcing the zero displacement constraints at the support locations. Polynomial approximation functions are used, and the constitutive relationships are written in terms of four lamination parameters. With these lamination parameters, the number of design variables is reduced to a minimum, which is useful for design optimization purposes, while all symmetric lay-ups are considered. This paper illustrates how the lamination parameters can be used for optimal design of vibrating plates. Results …

A New Neural Architecture For Homing Missile Guidance, S. N. Balakrishnan, Victor Biega

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We present a new neural architecture which imbeds dynamic programming solutions to solve optimal target-intercept problems. They provide feedback guidance solutions, which are optimal with any initial conditions and time-to-go, for a 2D scenario. The method discussed in this study determines an optimal control law for a system by successively adapting two networks - an action and a critic network. This method determines the control law for an entire range of initial conditions; it simultaneously determines and adapts the neural networks to the optimal control policy for both linear and nonlinear systems. In addition, it is important to know that …

Flow Diagnostics, Chemically Reacting Turbulent Flow Modeling And Turbulent Mixing : A Summary Of Project Studies In Combustion, Bahman Ghorashi

Scholarship Collection

No abstract provided.

A Nonlinear Dynamic Method For Supporting Large-Scale Decision-Making In Uncertain Environments, Wayne Woodhams

Engineering Management & Systems Engineering Theses & Dissertations

This research developed a methodology for supporting decision making by reducing uncertainty in decision environments which are too large, dynamic and complex to be treated by traditional quantitative and simulation techniques. These environments are complex because of the free choice associated with human involvement, and the existence of a large number of interrelated factors which influence the outcomes of the decision process. They are dynamic because the ground rules affecting those interrelationships are constantly changing. Uncertainty cannot be treated probabilistically, since identification of a full set of outcomes and factors of influence is not possible.

The venue for the investigation …

Towards A More Hands-On, Design-Oriented Course On Mechanisms, Burford Furman

Faculty Research, Scholarly, and Creative Activity

No abstract provided.

Compressible Turbulence Measurements In A Supersonic Flow With Adverse Pressure Gradient, Jon W. Dotter

Theses and Dissertations

Mean flow and compressible turbulence measurements have been obtained upstream and within a shock boundary interaction and a compression ramp in Mach 3 flow. Compressible turbulence models have met with little success in the accurate prediction of high-speed flows involving complicated shock boundary interactions and adverse pressure gradients because of a crucial lack of experimental data. Data were collected using conventional Pitot and cone static probes, single overheat cross-wire anemometry, multiple overheat cross-wire anemometry, and flow visualization techniques. Direct measurements of the total Reynolds shear stress were obtained using a turbulence transformation. Results indicate that compressibility effects, as evidenced by …

Investigation Into The Behavior Of Geometrically Nonlinear Composite Arches, John C. Bailey

Theses and Dissertations

This research modifies the existing finite element formulation of a potential energy based large deformation and moderate rotation theory. Hermitian shape functions replace the existing linear bending angle interpolations. Negligible differences between the two formulations indicate the underlying kinematics limit the accuracy, not the finite element interpolations. Using the new program, numerous nonlinear arch geometries are modeled to investigate the effects of arc length and thickness variations. Local and global snapping phenomena are captured as well as through the thickness shear driven nonlinearities.

Flight Control Design Using Mixed H2/Μ Optimization, Douglas D. Decker

Theses and Dissertations

This thesis examines the use of the mixed H2-Microns optimal control synthesis method in the design of a flight control system for the lateral-directional axes of the F-16 Variable Stability In-Flight Simulator Test Aircraft (VISTA). The method is designed to minimize the H2 norm (two-norm) for a given value of microns. This should provide adequate noise and disturbance rejection while maintaining robustness against several types of uncertainties in the system. This thesis finds that, for this problem, the two-norm is not an accurate representation of the outputs of interest. When the two-norm is broken up into its constituent parts an …

Effects Of Blowing Ratio On Heat Transfer To The Throat Region Of A Porous-Walled Nozzle, Joseph L. Lenertz

Theses and Dissertations

This experiment analyzed the effects of blowing ratio on heat transfer to the throat region of a porous-walled nozzle, using the AFIT low speed shock tube. Heat flux data were taken from both sides of a two-dimensional Mach 2.0 Re-m=5.2x10⁷ nozzle using thin film resistance thermometers. One side was transpiration-cooled by secondary air injection through a sintered wall, while the other side served as a control. Control results were validated using empirical relations, and cooled side results showed up to a 14% reduction in heat transfer coefficient at blowing ratios of only 0.51%. The linear nature of cooling effectiveness …

Investigation Of Boundary Layer And Performance Effects Of Transpiration Cooling Through A Porous Plate In A Rocket Nozzle, David N. Keener

Theses and Dissertations

This study used a range of low blowing ratios with air through an area of porous material in a Mach 2.0 nozzle to quantity the change in boundary layer thickness as a function of blowing ratio. Also, exit and wall Mach number profiles at each blowing ratio were collected to characterize performance losses as a result of blowing. Performance in terms of specific impulse was also studied. As expected, the boundary layer thickness increased and nozzle performance in terms of exit Mach number decreased with increasing blowing ratio.

The Collapse Of Composite Cylindrical Panels With Various Thickness Using Finite Element Analysis, Christopher P. Chaplin

Theses and Dissertations

This study compared numerical collapse results of graphite-epoxy cylindrical panels with free vertical edges undergoing axial compression for three different shell theories. Symmetric quasi-isotropic laminates were investigated using solid panels and panels with five different centralized cutouts with three thicknesses. The theories compared in the study were the Simplified Large displacement moderate Rotation (SLR) theory, the Donnell Cylindrical Shell (Modified Donnell) theory, and the Classical Donnell theory. The purpose of the study was to determine when large rotations and through-the-thickness shear become important in the numerical collapse analysis of cylindrical composite shells. By observing cases where the numerical collapse results …

The Design And Development Of A Low-Speed, Low-Force Wind Tunnel Data Acquisition System With An Application To Bicycle Front Fork Spacing, Alan W. Elledge

Theses and Dissertations

This thesis encompassed the design, development, and application of a low-speed, low-force data acquisition system for the AFIT 5-ft Wind Tunnel. The new data acquisition system was designed and developed to measure approximately 0.045 N (about 0.01 lb_f) at nearly 64.4 km/h (40 mph). Verification of the capability was obtained through testing of a cylindrical model. As part of a technology transition program with Wright Laboratory, this new system was used to investigate bicycle front fork blade spacing in order to determine the optimal spacing for minimum drag. As for the minimum drag of a bicycle with an …

Viscoplastic Characterization And Fatigue Modeling Of Titanium Based Metal Matrix Composites, Mark A. Foringer

Theses and Dissertations

Viscoplastic characterization and fatigue modeling of titanium-based metal matrix composites was accomplished by combining a unified viscoplastic theory, a nonlinear micromechanics model, and a linear damage accumulation model. First. Ti 15-3 was characterized using the Bodner-Partom viscoplastic theory. A micromechanics model was then employed in a linear damage accumulation fatigue model to predict the fatigue behavior of titanium based composites. The viscoplastic behavior predictions of the micromechanics model were used to eliminate separately defined time dependent terms in the fatigue model. Also, a new linear damage accumulation model was developed from the fatigue behavior of the composite constituents. Finally, it …

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite At Elevated Temperature Under Tension-Tension Loading, Craig D. Steiner

Theses and Dissertations

This study investigated the fatigue behavior and damage mechanisms of a [0-90]_4s SiC-MAS ceramic matrix composite under tension-tension loading at two elevated temperatures and two frequencies. Stress and strain hystereses, maximum and minimum strain, and modulus of elasticity were evaluated to characterize the material behavior. Microscopy and fractography were used to evaluate damage progression and mechanisms. Fatigue life was independent of frequency at both temperatures.

Investigation Of Tension-Compression Fatigue Behavior Of A Unidirectional Metal Matrix Composite At Elevated Temperature, Darren L. Kraabel

Theses and Dissertations

This study investigated the fatigue behavior in a unidirectional metal matrix composite under tension-compression loading conditions. Stress-strain responses, modulus and strain trends were monitored to characterize damage. Fractography and microscopy were used to characterize failure modes. Fatigue life curves were plotted base on different parameters such as stress and strain. Tension-compression fatigue life was shorter than the obtained under tension-tension fatigue cycling. Creep, observed in tension-tension. fatigue cycling, and the effects of the compressive load on the plastic zone around the crack tip explain shorter life under tension-compression fatigue loading.

Finite Element Methods For Nonlinear Static Analysis Of Sandwich Plates, Damin J. Siler

Theses and Dissertations

A finite element method, developed for static analysis of composite plates, was enhanced to be used with sandwich plates. The theory considers geometric nonlinearity and transverse shear. Furthermore, a new postprocessor was written to check for initial failure using the maximum stress criteria. It also includes a procedure for evaluating transverse normal stresses by enforcing equilibrium. The code modifications for sandwiches were verified by comparing finite element solutions to closed-form sandwich theories. Both methods showed good correlation. In addition, comparisons between one type of composite plate and a similar sandwich plate found that the sandwich had better specific stiffness for …

Applications Of ℓ1 And Mixed H2/ℓ1 Optimization, Mark S. Spillman

Theses and Dissertations

This thesis explores the use of ℓ₁ and mixed H2/ℓ1 optimization methods to design flight control systems. ℓ₁ optimization is used to handle tracking issues in the design of digital compensators. Control deflection and rate limitations, overshoot and undershoot limitations and steady-state error requirements are discussed. Model-matching techniques which produce acceptable tracking results with lower order controllers are also examined. New numerical methods for continuous H2/L1 and discrete H2/ℓ1 optimization are presented. These methods are used to design an aircraft controller in continuous and discrete time and the results are compared.

Improved Numerical Solution Of Mixed H2/H∞ Optimization With Applications, Linda D. Smith

Theses and Dissertations

This study improved the numerical optimization technique used to compute mixed H₂/H_∞ controllers. The run time to generate the full curve of an H₂/H_∞ design was reduced by a factor of almost 200 for a specific example. This was accomplished by improving gradient calculations, upgrading the H_∞ norm calculation to capture multiple peaks in the singular value plot and using routines that minimized processing time. The optimization routine used was the MATLAB CONSTR' Sequential Quadratic Programming (SQP) routine. This SQP routine was compared to a FORTRAN SQP numerical optimizer, IMSL-DNCONG. The method was …