Other Mechanical Engineering Commons^™

Test 2145: John Deere 6135e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Restraint System Design And Evaluation For Military Specific Applications, Sebastian Karwaczynski

Dissertations, Master's Theses and Master's Reports

This research focuses on designing an optimal restraint system for usage in a military vehicle applications. The designed restraint system must accommodate a wide range of DHM’s and ATD’s with and without PPE such as: helmet, boots, and body armor. The evaluation of the restraint systems were conducted in a simulated vehicle environment, which was utilized to downselect the ideal restraint system for this program.

In December of 2011 the OCP TECD program was formulated to increase occupant protection. To do this, 3D computer models were created to accommodate the entire Soldier population in the Army. These models included the …

An Experimental Investigation Of Low Temperature Combustion Regimes In A Light Duty Engine, Kaushik Kannan

Dissertations, Master's Theses and Master's Reports

A continuous investigation on the improvement of internal combustion engines is necessary due to the stringent emission and fuel economy regulations. Low Temperature Combustion (LTC) is a promising field of research since it can simultaneously reduce NOx and soot while attaining high thermal efficiencies in automotive engines. A thorough study of several LTC regimes is necessary to understand the quantitative comparison and the extent of feasibility of these regimes functioning on an automotive engine. This thesis concentrates on an experimental investigation of three different LTC modes namely Homogeneously Charged Compression Ignition (HCCI), Partially Premixed Compression Ignition (PPCI) and Reactivity Controlled …

Test 2158: Case Ih Farmall 130a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2157: Case Ih Farmall 120a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1065 Challenger Mt515e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1139 New Holland T4.120, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1129 Case-Ih Farmall 120u, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1096 Case-Ih Maxxum 145, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

The University Of Akron Nfpa 2015/2016 Chainless Challenge, Andrew Tupta, Andrew Ball, Stefan Stamboldziev, Jordon Spence, Sean Catchpole

Williams Honors College, Honors Research Projects

Parker Hannifin has issued a challenge to student design teams of creating a Chainless bike using a hydraulic system. Each student design team will be assigned a technical advisor from the University. The project will be divided into two phases after the initial kickoff. The first phase will align with senior design course for motion control and hydraulics and will yield the student obtaining knowledge in hydraulics, including bio-degradable fluids, pneumatics, electromechanical systems, green technologies (sustainable energy) and controlling force and motion. Students will be provided data sheets, a list of in-stock Parker components and by the end of the …

The University Of Akron Human Powered Vehicle Team, Maria E. Rizzo, Andrew J. Derhammer, Christopher M. Trowbridge, Timothy M. Nutt, Joseph R. Boyd, Jeremy W. Marcum, Jonathan E. Adams, Donald G. Haiss, Julia Wood, Brian D. Goshia, Scott T. Fagan, Joshua D. Everhard, Rebecca L. Slivka

Williams Honors College, Honors Research Projects

The University of Akron Human Powered Vehicle Team’s 2016 vehicle, Klokan, was designed, manufactured and tested with safety, reliability, performance and ease of use in mind. The vehicle is a fully faired tadpole trike with a lightweight aluminum frame constructed from 6061-T6 tubing having a total weight of 8.9 lbs. To complement the lightweight frame, the fairing is constructed from polycarbonate, PETG and carbon fiber strips which combine into a lightweight, easy to manufacture weather barrier and aerodynamic structure. Klokan was designed to be a safe and efficient mode of everyday transportation which ensures that riders are sufficiently protected by …

Static And Dynamic Behavior Of Carbon Fiber Reinforced Aluminum (Carall) Laminates, Gurpinder Singh Dhaliwal

Wayne State University Dissertations

STATIC AND DYNAMIC BEHAVIOUR OF CARBON FIBER REINFORCED ALUMINUM (CARALL) LAMINATES

by

GURPINDER SINGH DHALIWAL

Advisor: Dr. Golam Newaz

Major: Mechanical Engineering

Degree: Doctor of Philosophy

The main aim of this research work was to investigate the static and dynamic properties of carbon fiber reinforced aluminum laminates cured without using any external adhesive and acid treatment of aluminum layers. A comprehensive study was undertaken to study the effect of adding epoxy resin rich polyester synthetic surface veil cloth layers on the failure modes and flexural and tensile response of these fiber metal laminates (FMLs). The main purpose of adding veil …

In Situ Microscopy Of The Self-Assembly Of Branched Nanocrystals In Solution, Eli Sutter, Peter Sutter, Alexei V. Tkachenko, Roman Krahne, Joost De Graaf, Milena Arciniegas, Liberato Manna

Department of Mechanical and Materials Engineering: Faculty Publications

Solution-phase self-assembly of nanocrystals into mesoscale structures is a promising strategy for constructing functional materials from nanoscale components. Liquid environments are key to self-assembly since they allow suspended nanocrystals to diffuse and interact freely, but they also complicate experiments. Real-time observations with single-particle resolution could have transformative impact on our understanding of nanocrystal self-assembly. Here we use real-time in situ imaging by liquid-cell electron microscopy to elucidate the nucleation and growth mechanism and properties of linear chains of octapod-shaped nanocrystals in their native solution environment. Statistical mechanics modelling based on these observations and using the measured chain-length distribution clarifies the …

Influence Of Shear Stress Magnitude And Direction On Atherosclerotic Plaque Composition, Ryan M. Pedrigi, Vikram V. Mehta, Sandra M. Bovens, Zahra Mohri, Christian Bo Poulsen, Willy Gsell, Jordi L. Tremoleda, Leila Towhidi, Ranil De Silva, Enrico Petretto, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

The precise flow characteristics that promote different atherosclerotic plaque types remain unclear. We previously developed a blood flow-modifying cuff for ApoE^−/− mice that induces the development of advanced plaques with vulnerable and stable features upstream and downstream of the cuff, respectively. Herein, we sought to test the hypothesis that changes in flow magnitude promote formation of the upstream (vulnerable) plaque, whereas altered flow direction is important for development of the downstream (stable) plaque. We instrumented ApoE^−/− mice (n=7) with a cuff around the left carotid artery and imaged them with micro-CT (39.6 μm resolution) eight to nine weeks …

Comparative Analysis Of Locally Available Materials For Treadle Pump Seals In Senegal, West Africa, Brennan Tymrak

Dissertations, Master's Theses and Master's Reports

For rural farmers in Senegal, West Africa, pulling water for irrigation can be a laborious but necessary task during the dry season to earn income from vegetable gardening. Traditional water pulling methods are inexpensive but require great physical effort, while modern machines decrease the labor burden but at a high financial cost. This study looked at an intermediate water pulling technology, the treadle pump, and how it could be improved to become more desirable for use in agricultural irrigation. A treadle pump was built and tested during field work in a rural Senegalese village. Observations from field testing prompted a …

Biomimetic Substrate Control Of Cellular Mechanotransduction, Mohammad Nahid Andalib, Yuris A. Dzenis, Henry J. Donahue, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

Extracellular mechanophysical signals from both static substrate cue and dynamic mechanical loading have strong potential to regulate cell functions. Most of the studies have adopted either static or dynamic cue and shown that each cue can regulate cell adhesion, spreading, migration, proliferation, lineage commitment, and differentiation. However, there is limited information on the integrative control of cell functions by the static and dynamic mechanophysical signals. For example, a majority of dynamic loading studies have tested mechanical stimulation of cells utilizing cultures on flat surfaces without any surface modification. While these approaches have provided significant information on cell mechanotransduction, obtained outcomes …

Characterizing The Boundary Lateral To The Shear Direction Of Deformation Twins In Magnesium, Y. Liu, N. Li, S. Shao, M. Gong, J Wang, R.J. Mccabe, Y. Jiang, C.N. Tome

Department of Mechanical and Materials Engineering: Faculty Publications

The three-dimensional nature of twins, especially the atomic structures and motion mechanisms of the boundary lateral to the shear direction of the twin, has never been characterized at the atomic level, because such boundary is, in principle, crystallographically unobservable.We thus refer to it here as the dark side of the twin. Here, using high-resolution transmission electron microscopy and atomistic simulations, we characterize the dark side of {1012} deformation twins in magnesium. It is found that the dark side is serrated and comprised of {1012} coherent twin boundaries and semi-coherent twist prismatic–prismatic {2110} boundaries that control twin growth. The conclusions of …

Stress-Dependent Ultrasonic Scattering In Polycrystalline Materials, Christopher M. Kube, Christopher A Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Stress-dependent elastic moduli of polycrystalline materials are used in a statistically based model for the scattering of ultrasonic waves from randomly oriented grains that are members of a stressed polycrystal. The stress is assumed to be homogeneous and can be either residual or generated from external loads. The stress-dependent elastic properties are incorporated into the definition of the differential scattering cross-section, which defines how strongly an incident wave is scattered into various directions. Nine stress-dependent differential scattering cross-sections or scattering coefficients are defined to include all possibilities of incident and scattered waves, which can be either longitudinal or (two) transverse …

Graphene Platform For Neural Regenerative Medicine, Tasneem Bouzid, Alexander Sinitskii, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

Graphene is a material composed of a single layer of carbon atoms arranged in a two-dimensional honeycomb lattice. The unique electrical, optical, thermal, and mechanical properties of graphene are extensively exploited for various applications in electronics, energy, and sensors. Studies also proposed the potential of graphene for biomedical applications. The intrinsic characteristics of graphene and its availability for chemical and physical modifications make graphene a promising vehicle for various biomedical applications including drug delivery, bioimaging, disease diagnostics, etc. The chemical structure of graphene and, in turn, its functionality, can be altered by attaching functional groups, which not only modify the …

Mode-Converted Ultrasonic Scattering In Polycrystals With Elongated Grains, Andrea P. Arguelles, Christopher M. Kube, Ping Hu, Joseph A. Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Elastic wave scattering is used to study polycrystalline media for a wide range of applications. Received signals, which include scattering from the randomly oriented grains comprising the polycrystal, contain information from which useful microstructural parameters may often be inferred. Recently, a mode-converted diffuse ultrasonic scattering model was developed for evaluating the scattered response of a transverse wave from an incident longitudinal wave in a polycrystalline medium containing equiaxed single-phase grains with cubic elastic symmetry. In this article, that theoretical mode-converted scattering model is modified to account for grain elongation within the sample. The model shows the dependence on scattering angle …