Other Mechanical Engineering Commons^™

Strain-Based Design Of Steel-Polymer-Steel Composite Pipes, Vul Thang

LSU New Orleans Theses and Dissertations

Many offshore single-wall pipelines and structural failures have occurred in the past. As a result, lives were lost, and billions of dollars were spent. In addition, natural disasters such as earthquake fault zones can cause a large volume of soil movement. This can easily damage single-wall pipelines or piles of fixed offshore platforms in the earthquake fault zone.

Currently, the single-wall pipelines are used for the offshore and onshore oil and gas industry. This research investigated the use of double-wall composite pipe steel-polymer-steel (SPS) in place of single-wall pipe to prevent such failures. The double-wall composite pipe has a larger …

Cal Poly Fluid Power Vehicle Challenge 2022, Sangmin Sung, Eddy Rodriguez, Travis Welch, Jeremy Baechler, Kevin Pauls

Mechanical Engineering

In this report, the Featherweight Cycles design team puts forth the scope and overview of their design project, discusses background research and competitor analysis, and presents the project’s final design and manufacturing plans. The overall goal of this project is to fabricate and compete in the Fluid Power Vehicle Challenge, hosted by the National Fluid Power Association. To better define the design process, the team researched previous year’s designs from Cal Poly, as well as winning designs from the last two years to form a baseline of knowledge about competing schools’ designs. After researching multiple design paths, Featherweight Cycles chose …

Fluid Structure Interactions Within A Common Rail Diesel Injector., Russell Prater

Electronic Theses and Dissertations

The internal flow of a high-pressure diesel injector is simulated numerically to investigate the complex transient flow structures and the unsteady forces imparted to the injector needle that result from the asymmetric flow fields developed during operation. The gas-liquid two phase flow is simulated using a mixture model with the cavitation numerically modeled using the Zwart-Gerber-Belamri model. Both the k-ε model and the detached eddy simulation (DES) model are used, and the numerical results are compared. This dissertation looks at the internal flow of a generic injector at different lifts and characterizes the flow parameters at high lift and low …

Predictive Performance And Teaming Via The Mist-C Ocean Hierarchy Utilizing Personality And Skills, Brighton H. Owen

All Theses

This thesis seeks to establish and define the individual, the team as an entity, and qualify various metrics to predict team performance. When several individuals come together, they form a team that is often capable of designing and developing concepts beyond the individual on their own by methods of task dispersion, goal orientation, communication, and more. With these teams comes growth and increased performance leading to more efficient processes and better metrics by which performance may be measured. To achieve this, 34 engineering students in the AerosPACE senior design program, which lasted two semesters, were asked to complete surveys in …

Analysis Of The Self-Heating Effect On Unfilled Poly(Methyl Methacrylate) Due To Cyclic Behavior, Muhammed R. Kose

All Theses

Poly(methyl methacrylate, (PMMA) has been implemented as part of the supporting structure in complete hip and knee replacements since the 1950s. Known as bone cement while in the body, PMMA is known to undergo compressive and tensile stresses that wear down the bio-compatible barrier and cause pieces to come loose inside the human body. These pieces are then attacked by the body’s own nervous system, leading to inflammation, and eventually necessitating replacement. It has been documented that under cyclic loading PMMA can reach temperatures that start to degrade its tensile capabilities. In this study the potential cause of self-heating was …

Investigating The Effects Of Topology On The Fracture And Failure Mechanisms Of Low Density Metamaterials, Kaitlynn Melissa Conway

All Dissertations

Advances in additive manufacturing have enabled the creation of low density metamaterials with fine features and complex topographies. These new metamaterial topologies and size scales not previously possible broaden the spectrum of lightweight materials with unique properties that are advantageous in a variety of applications. There however is a lack of understanding of metamaterial failure and fracture behaviors. Studies tend to report only a few material properties rather than a comprehensive description of behavior. Due to this, there is a hesitancy to incorporate metamaterials into engineering designs despite proven remarkable properties. This work seeks to investigate in three parts the …

Characterization Of Friction Element Welding Using Finite Element Modeling, Ankit Varma

All Dissertations

Friction element welding (FEW) has been advocated as a solution to weld different materials together, with the ability to join high-strength materials for a range of thicknesses with low input energy and a short processing time. This work develops a coupled thermal-mechanical finite element model to better understand the physical mechanisms involved in the process and to predict temperature and material flow during the process. Furthermore, microstructural analysis is performed for the steel layer using a scanning electron microscope and Vickers microhardness tester to understand the variation in its grain structure and hardness. Results from the finite element model and …

Inertially Stabilized Gimbal, Miranda Grace Bilbrey

Honors Capstone Projects and Theses

No abstract provided.

A Molecular Dynamics Study Of The Laser Sintering Process And Subsequent Mechanical Properties Of Γ-Tial Nanoparticles, Eleanor Dickens

Honors Theses

Using molecular dynamics (MD) simulations, the laser sintering additive manufacturing process is investigated through the observation of γ-TiAl nanoparticles. This process is conducted using both uni-directional chain and stacking configurations. By mimicking the heating process and varying laser sintering parameters such as heating rater, sintering temperature, and particle orientation, the fusion behavior and resulting products are analyzed for both chain and stacking NP patterns. In of single chain cases, it is noticed that slower heating rates and higher melting temperatures yield larger neck growth between each individual particle and thus produce a more stable product. This leads to stronger mechanical …

Effects Of Varied Oxygen Levels, Laser Powers, And Scanning Speeds On Manufactured Components By Laser-Based Powder Bed Fusion, Amelia Mcnamee

Honors College Theses

This project addresses the effects of oxygen concentration, laser power, and scanning speed on the melt pool geometry of laser-based powder bed fusion (L-PBF) additively manufactured components. A parametric analysis using the substrate alone was conducted to determine a range of desirable laser powers and scanning speeds. The parameter with the more significant effect will be decided upon based on the depth-to-width ratios (D/W) of the resultant laser weld bead. A range of oxygen levels and scan speeds was selected for the next phase. These samples were then be analyzed for depth-to-width ratios. It was expected that higher oxygen concentrations …

Structural Health Monitoring Of Bioprinted Materials, Kathryn H. Mcintosh

Honors College Theses

Bioprinting is a new method that utilizes additive manufacturing to construct organs, tissues, and other biostructures. This method presents endless possibilities - less reliance on organ donors (according to the Health Resources and Services Administration, 17 people die each day waiting for an organ transplant in the U.S.), more transplant opportunities, and the ability to save significantly more lives. While bioprinting has opened a new frontier in the biomedical field, there may be some research issues that need to be addressed. For example, numerous researchers have focused on creating novel approaches to print complicated geometries. However, the structural integrity or …

Ultra-Broadband And Polarization-Insensitive Metasurface Absorber With Behavior Prediction Using Machine Learning, Shobhit K. Patel, Juveriya Parmar, Vijay Katkar, Fahad Ahmed Al-Zahrani, Kawsar Ahmed

Department of Mechanical and Materials Engineering: Faculty Publications

The solar spectrum energy absorption is very important for designing any solar absorber. The need for absorbing visible, infrared, and ultraviolet regions is increasing as most of the absorbers absorb visible regions. We propose a metasurface solar absorber based on Ge₂Sb₂Te₅ (GST) substrate which increases the absorption in visible, infrared and ultraviolet regions. GST is a phase-changing material having two different phases amorphous (aGST) and crystalline (cGST). The absorber is also analyzed using machine learning algorithm to predict the absorption values for different wavelengths. The solar absorber is showing an ultra-broadband response covering a 0.2–1.5 …

Quantification Of Reynolds Shear Stress Wave-Phase Dependence In Fixed-Bottom Offshore Wind Turbine Via Quadrant Analysis, Cerrina Mouchref

University Honors Theses

As the need for a reliable renewable energy supply is increasing, many have looked to offshore wind because they hold more potential for power production than onshore wind. Interests in expanding offshore wind energy has brought along many challenges when it comes to understanding the complex dynamics experienced offshore, including the relationship between the wind-turbine generated wakes and ocean waves. This experimental study characterizes the relationship between Reynolds shear stress and the phase of surface waves above the air-sea interface in the wind-turbine wake region. The experimental setup combines a wave tank, wind tunnel, and a fixed-bottom wind turbine. Particle …

Closed-Loop Control Of Meltpool Temperature In Directed Energy Deposition, Ziyad M. Smoqi, Ben Bevans, Aniruddha Gaikwad, James Craig, Alan Abul-Haj, Brent Roeder, Bill Macy, Jeffrey E. Shield, Prahalada K. Rao

Department of Mechanical and Materials Engineering: Faculty Publications

The objective of this work is to mitigate flaw formation in powder and laser-based directed energy deposition (DED) additive manufacturing process through close-loop control of the meltpool temperature. In this work, the meltpool temperature was controlled by modulating the laser power based on feedback signals from a coaxial two-wavelength imaging pyrometer. The utility of closed-loop control in DED is demonstrated in the context of practically inspired trapezoid-shaped stainlesssteel parts (SS 316L). We demonstrate that parts built under closed-loop control have reduced variation in porosity and uniform microstructure compared to parts built under open-loop conditions. For example, post-process characterization showed that …

Mechanical Horse Project, Hernan Ramirez Resendiz, Ben Apt

Mechanical Engineering

This document outlines our senior design project for the Cal Poly Mechanical Engineering Department on behalf of Jack’s Helping Hand. As a team of two Mechanical Engineering students, we developed a structure that can support a rider and can move in three degrees of freedom to model the gait patterns of a horse. This senior project will be continued by another group that will focus on electronics and implement the motors that will induce motion on the structure that our team has built. We collected baseline data by attaching an iPhone to a horse and used that motion to compare …

Effect Of Indentation On Sandwich Composite Structure Mechanical Behavior, Marius V. Jatulis

Master's Theses

Composite sandwich structures are prevalent in engineering applications where high strength to weight ratios are critical. A composite sandwich includes the addition of a core material between two composite face sheets to increase ultimate stress in compression and bending loading cases. The performance of many composite sandwich structure configurations is well understood in the undamaged case. This analysis examines a type of damage, low velocity indentation, and determines the effect on mechanical behavior. The scope of the analysis includes manufacturing sandwich composite structures, creating indentation in the composite, and testing the sandwich composite structure. The mechanical behavior of the composite …

Monitoring Of State Transitions In Extreme Environment Application Materials Using Fiber Bragg Grating Sensors, Sabuj Khadka

Electronic Theses and Dissertations

By embedding both a single fiber Bragg grating (FBG) sensor and a thermocouple (TC) during the manufacturing for extreme environment applications of certain classes of materials such as metals and polymers, a novel in-situ approach was developed to precisely monitor their entire manufacturing processes. This novel monitoring technique was able to identify many characteristic points during the curing of room and high-temperature epoxies and the solidification processes of metal alloys composed of tin and bismuth which were selected in this research purely for verification purposes. Some of the characteristic points identified for the epoxies were: (i) the gel point, (ii) …

R/C Baja Truck Suspension, Chassis And Steering, Ryan Lafrombois

All Undergraduate Projects

The ASME RC Baja Challenge is an annual competition that the Central Washington University Mechanical Engineering and Technology (MET) department takes part in. Senior level engineers divided the work between the drivetrain and the chassis/suspension while designing and manufacturing to meet a set of requirements. Next, a device was to be developed to be able to withstand the extreme forces to be successful in the competition at the end of the year. The process would require that the students use their acquired knowledge and skills to design, manufacture, and analyze a capable device. Designing involved the completion of 12 analyses …

Determining Cause Of Failure For Load Cells Supporting Vertical Pressure Vessels Subject To Wind Loading, Seth Nowak

College of Graduate Studies: Theses & Dissertations

Wind loads cannot be avoided during a natural disaster such as a hurricane and could affect the strength and stability of vertical pressure vessels during exposure. Vertical pressure vessels cater to large wind loads; therefore, it is imperative to study the effect of additional loading on the structures. In this study, three pressure vessels with volumes of 50 CuFt, 200 CuFt, and 1100 CuFt, supported by three equidistant load cells under their legs are individually analyzed to determine von mises stress to estimate yield failure criteria. Two load rating criteria, maximum load capacity and water-filled condition (critical condition) are utilized …

Recent Advances In Biosensors For Detection Of Covid-19 And Other Viruses, Shobhit K. Patel, Jaymit Surve, Juveriya Parmar, Kawsar Ahmed, Francis M. Bui, Fahad Ahmed Al-Zahrani

Department of Mechanical and Materials Engineering: Faculty Publications

This century has introduced very deadly, dangerous, and infectious diseases to humankind such as the influenza virus, Ebola virus, Zika virus, and the most infectious SARS-CoV-2 commonly known as COVID-19 and have caused epidemics and pandemics across the globe. For some of these diseases, proper medications, and vaccinations are missing and the early detection of these viruses will be critical to saving the patients. And even the vaccines are available for COVID-19, the new variants of COVID-19 such as Delta, and Omicron are spreading at large. The available virus detection techniques take a long time, are costly, and complex and …