Other Mechanical Engineering Commons^™

Olympic Bocce Ballers, Steven Erickson, William Haley, Taylor Vaughan

Mechanical Engineering

No abstract provided.

Piedras Blancas Light Station Vista Point Improvement Plan, Larissa Heeren, Reuben Juster, Annamarie Usher, John Rossi, Nick Mitchell

Mechanical Engineering

Piedras Blancas Light station Improvement Involved the design of two separate parking lot/vista point plans as well as the creation of a concrete Iron Ranger located near the gift shop on site.

Thermodynamic Based Model Eliciting Activities For Undergraduate Mechanical Engineering Education, Paul Nicholas Van Bloemen Waanders

Master's Theses

Undergraduate engineering education is designed to prepare students for their careers.  The rise of technology in modern engineering allows for a shift in the way undergraduates are prepared for the modern workplace.  Model Eliciting Activities (MEAs) allow students to think critically about their own work and allow instructors to analyze the students’ problem solving methods.  To ensure that new MEAs are as effective as possible they are subject to six basic principles: model construction, reality, generalizability, self-assessment, model documentation, and effective prototype.

This document focuses on evaluating new MEAs for their adherence to the six principles from an instructor's and …

Bevcool, Matthew (Matt) Slette, Ryan Talyat, Camille Sybert

Mechanical Engineering

A consumer product for rapidly cooling canned and bottled beverages.

Marauder Marine: Spearfishing Float Design, Kevin Glen, Kyle Lancaster, Andrew Wickham

Mechanical Engineering

No abstract provided.

Pop-A-Wheelie Design Team, Mackenzie Hill, Thuyen Nguyen, Shaun Van't Hul

Mechanical Engineering

The purpose of this report is to illustrate the Pop-a-Wheelie design team’s progression and implementation of a concept in regards to the project sponsored by Break the Barriers (BTB). The Pop-a-Wheelie design team was tasked to design two devices that will be attached onto wheelchairs. The devices should facilitate the independence of user’s ability to pop-a-wheelie and return to an upright position without any assistance. After a list of specifications was agreed upon, the design process initiated. All customer specifications are listed in Objectives section located in Chapter 1: Introduction. A complete engineering specification table can be found in the …

Cal Poly Human Powered Helicopter, Josiah Auer, Eric Behne, Dave Berry, Rebecca Hennings, James Koch, Ian Marquardt, Josiah Mayfield, Sean Miller

Mechanical Engineering

The following report encompasses the Cal Poly Human Powered Helicopter team’s efforts during the 2010-2011 academic year. The intention of this project is to further the knowledge of human powered helicopter design and to validate an ideal configuration through experimental tests and analysis. 

A. Background

The Sikorsky Prize offered by the American Helicopter Society has been the catalyst for many attempts at Human Powered Helicopter (HPH) flight. The requirement to win the prize is a continuous, human powered flight of more than 60 seconds that stays within a 10 meter square box and reaches an altitude greater than 3 meters …

Solar Powered Oil Well Site, Jonathan Hyland, Matthew Mastro, Kyle Moore

Mechanical Engineering

No abstract provided.

Optimization And Modeling Tools For Telescope Hexapod Structures, Michael Edward Feeney

Master's Theses

Hexapod trusses are an important element in many mechanical design systems. The natural frequency and stiffness behavior under geometric and mass variations of such structures is largely undocumented. Furthermore, the ability to quickly model hexapod designs and explore a large design-space in finite element software packages is, in general, time consuming and inefficient. The purpose of this project was to develop software tools that made design-space exploration (modeling and simulation processes) for hexapod structures drastically more efficient. Secondly, the project included an experimental analysis portion to demonstrate the various modal study techniques and to validate finite element analysis predictions. Lastly, …

A Virtual Supply Airflow Rate Meter In Rooftop Air Conditioning Units, Daihong Yu

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

Virtual sensing technology aims to estimate difficult to measure, expensive, or new quantities by using multifarious mathematical models along with non-invasive and low-cost measurements. Such embedded intelligence is a key to improving the performance of building systems in terms of functionality, safety, energy efficiency, environmental impacts, and costs. Considering the progress that has been achieved over many various fields (e.g., process controls, automobiles, avionics, autonomous robots, telemedicine) within the last two decades, numerous intelligent features have been incorporated and enabled that would otherwise not be possible or economical.

To identify the potential opportunities and research/development needs of virtual sensing technology …

Simulation And Validation Of Two-Component Flow In A Void Recirculation System, Oscar Eduardo Daza

Master's Theses

Nuclear power plants rely on the Emergency Core Cooling System (ECCS) to cool down the reactor core in case of an accident. Occasionally, air is entrained into the suction piping of ECCS causing voids that decrease pumping efficiency, and consequently damage the pumps. In an attempt to minimize the amount of voids entering the suction side of the pump in ECCS, a Void Recirculation System (VRS) experiment was conducted for a proof of concept purpose. While many studies have been oriented in studying two-component flow behavior in ECCS, none of them propose a solution to minimize air entrainment. As a …

Design And Calibration Of A Wind Tunnel Facility For The Study Of Active Flow Control On Wind Turbine Blades, Christopher Paul Walter

Renée Crown University Honors Thesis Projects - All

Our group at Syracuse University has been working under Professor Mark Glauser as part of a wind consortium with the University of Minnesota and United Technologies Research Group. Our component of this project will be to develop a system which can be imbedded in an airfoil which can increase the efficiency of the airfoil. Along with developing this “intelligent blade,” we will also be characterizing the affect our control system will have on aerodynamic noise. To accomplish these goals, Syracuse University’s anechoic jet facility was remodeled to incorporate a wind tunnel within which we could run our experiments. Upon the …

Analysis Of A Monolithic Crystal Plate Acoustic Wave Filter, Huijing He

Department of Mechanical and Materials Engineering: Faculty Publications

We study thickness–shear and thickness–twist vibrations of a finite, monolithic, AT-cut quartz plate crystal filter with two pairs of electrodes. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56 . An analytical solution is obtained using Fourier series from which the res-onant frequencies, mode shapes, and the vibration confinement due to the electrode inertia are calculated and examined.

Transverse Permeability Of Fibrous Porous Media, Ali Tamayol, Majid Bahrami

Department of Mechanical and Materials Engineering: Faculty Publications

In this study, the transverse permeability of fibrous porous media is studied both experimentally and theoretically. A scale analysis technique is employed for determining the transverse permeability of various fibrous matrices including square, staggered, and hexagonal arrangements of unidirectionally aligned fibers, as well as simple two-directional mats and simple cubic structures. In the present approach, the permeability is related to the porosity, fiber diameter, and tortuosity of the medium. In addition, the pressure drop in several samples of tube banks of different arrangements and metal foams are measured in the creeping flow regime. The pressure-drop results are then used to …

Improved Rehabilitation And Exercise Machine / Machine De Reeducation Et D'Exercice Amelioree, Judith M. Burnfield, Adam Taylor, Thad W. Buster, Carla A. Nelson, Yu Shu

Department of Mechanical and Materials Engineering: Faculty Publications

An improved rehabilitation and exercise machine is provided which allows a person with physical limitations, disabilities or chronic conditions to use the machine in order to rehabilitate their muscles, improve joint flexibility, and enhance cardiovascular fitness. An embodiment of the device includes a framework, a first and second crank arm, a first and second handle bar, a first and second foot pedal, a motor and pulley assembly, a first and second coupler link, and a motor controller with speed knob,

Mechatronics Application To Solar Tracking, Danny L. Rodriguez Jr

Purdue Polytechnic Directed Projects

The purpose of this was to design and implement a two-axis solar tracking system utilizing the National Instruments C-Rio real time controller. In order to accomplish this a prototype was modeled in CAD. This prototype used two 12 V DC motors to change a solar panel's rotation and tilt based on feedback data from three cadmium sulfide photoresistors. This configuration was chosen for its ability to create both a left-right rotational and an up/down tilt differential. In Addition this approach uses National Instruments Labview to control a solar tracking system. Using Labview add uniqueness to this project by adding a …

Test 2012a: New Holland Workmaster 55, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S806 New Holland T7.250, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Finite Element Reconstruction Of Real World Aortic Injury In Near-Side Lateral Automotive Crashes With Conceptual Countermeasures, Aditya Neelakanta Belwadi

Wayne State University Dissertations

Traumatic rupture of the aorta (TRA) remains the second most common cause of death associated with motor vehicle crashes after brain injury. On an average, nearly 8,000 people die annually in the United States due to blunt injury to the aorta. It is observed that more than 80% of occupants who suffer an aortic injury die at the scene due to exsanguination into the chest. With the advent of more accurate and established human body finite element (FE) models, FE crash reconstruction methods may become a valuable tool when assessing crash scenarios and occupant injury mechanisms.

The current study is …

Test 1999: John Deere 8335rt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …