Ocean Engineering Commons^™

Active Duty Training For Support Of Navy's Additive Manufacturing Strategy, Vukica M. Jovanovic, Onur Bilgen, Karina Arcaute, Michel A. Audette, Anthony W. Dean

Engineering Technology Faculty Publications

Additive manufacturing has recently gained the attention of multiple stakeholders, including those in the advanced manufacturing industry, research and government labs, academia, and the Navy community. Various efforts within the Navy focus on studying the best way for parts to be built and repaired for marine and naval vessels. Rapid manufacturing of spare components is particularly important for sailors, especially while deployed on warships, as they often do not have timely access to spare parts from the supply chain. For that purpose, a multidisciplinary team of engineering and education faculty have developed a series of workshops to train on-duty sailors …

Wave Motion Induced By Turbulent Shear Flows Over Growing Stokes Waves, Shahrdad Sajjadi, Serena Robertson, Rebecca Harvey, Mary Brown

Publications

The recent analytical of multi-layer analyses proposed by Sajjadi et al. (J Eng Math 84:73, 2014) (SHD14 therein) is solved numerically for atmospheric turbulent shear flows blowing over growing (or unsteady) Stokes (bimodal) water waves, of low-to-moderate steepness. For unsteady surface waves, the amplitude a(t)∝ekcita(t)∝ekcit, where kcikci is the wave growth factor, k is the wavenumber, and cici is the complex part of the wave phase speed, and thus, the waves begin to grow as more energy is transferred to them by the wind. This will then display the critical height to a point, where the thickness of the inner …

Numerical Computation Of Transient Response Of 2d Wedge Impact, Naresh Kumar Koyyapu

LSU New Orleans Theses and Dissertations

The diverse applications of advanced marine craft ascribed to their high speed and technological advancements has led to the use of stronger and lighter metals in such crafts. High speed, in effect also increases slamming loads as higher speed increases frequency of wave encounter while operating in waves. The present study is limited to wedge impact models. Fundamentally, the study is thus about two-dimensional (2D) wedge impact in water. In an attempt to predict the structural response to impact hydrodynamic force, a beam element based finite element (FE) computer program is written and the results of the code are presented …

Expression And The Functional Study Of Fusion Proteins Α-Amylase And Hemolysin- Αas An Application In Biofilm Polysaccharide Degradation, Gede Yuda Sugiarta, Anggoro Wiseso, Siska Yuliana Sari, Etri Dian Kamila, Vanessa Geraldine, Diana Christina, Muhammad Hanifi, Dwiantari Satyapertiwi, Robby Hertanto, Budiman Bela, Masafumi Yohda, Muhamad Sahlan

Makara Journal of Technology

Biofilm is an aggregate of consortium bacteria that adhere to each other on a surface. It is usually protected by the exopolysaccharide layer. Various invasive medical procedures, such as catheterization, endotracheal tube installation, and contact lens utilization, are vulnerable to biofilm infection. The National Institute of Health (NIH) estimates 65% of all microbial infections are caused by biofilm. Periplasmic α-amylase (MalS) is an enzyme that hydrolyzes α-1, 4- glicosidic bond in glycogen, starch, and others related polysaccharides in periplasmic space. Another protein called hemolysin-α (HlyA) is a secretion signal protein on C terminal of particular peptide in gram negative bacteria. …

Design Of The Human Assembly Strategy In A Self-Optimizing Assembly Cell: A Case Study Of Indonesians, Novie Susanto, Ratna Purwaningsih, Kharisma Panca Kurniawati

Makara Journal of Technology

This paper presents a continuing study of the human cognitive aspect application in the technical systems. The last studies design a human-centered design based on the German culture. The result shows a significant difference of human performance between Germans and Indonesians. Therefore, this study examines the human cognitive model based on Indonesian culture to investigate whether the different cognitive model based on the culture aspect can improve the human performance. The study was conducted on 60 people classified by age, young (16-34 years old) and old (older than 34 years old). Participants render predictions on an assembly activity for two …

Optimizing Supply Chain Collaboration Based On Agreement Buyer-Supplier Relationship With Network Design Problem, Wahyudi Sutopo, Ayu Erliza, Arien Heryansyah

Makara Journal of Technology

In recent years, the rising competitive environment with shorter product life cycles and high customization forces industries to increase their flexibility, speed up their response, and enhance concurrent engineering designs. To integrate these prospects, supply chain collaboration becomes a pertinent strategy for industries to strengthen their competitiveness. The network design problem is used to implement supply chain collaboration. In the buying and selling process, sharing information between buyer and supplier are important to obtain a transaction decision. The optimimum supply chain profit can be identified by mathematical model of network design problem. The Mathematical Model takes into consideration the uncertainity …

Effect Of Milling On The Densification Of Sic-Basedcomposites From Polysilazane, Alfian Noviyanto, Toshiyuki Nishimura

Makara Journal of Technology

High density SiC-based composites from polysilazane were fabricated by high energy milling and hot pressing. After cross-linking at 200 °C, the polysilazane was pyrolysed at 1000 °C in N2 for 2 h to form amorphous Si-C-N-O followed by high energy milling for 1 h. Milled amorphous Si-C-N-O was sintered in hot pressing at 1600 and 1700 °C for 1 h in vacuum under the applied pressure of 50 MPa. Although no sintering additives were used, dense SiC-based composites were obtained with this method. Sintered density was 3.04 g/cm3, while only 2.57 g/cm3 for amorphous Si-C-N-O without milling. It is suggested …

Characterization And Utilization Of Calcium Oxide (Cao) Thermally Decomposed From Fish Bones As A Catalyst In The Production Of Biodiesel From Waste Cooking Oil, Aldes Lesbani, Sabat Okta Ceria Sitompul, Risfidian Mohadi, Nurlisa Hidayati

Makara Journal of Technology

Thermal decomposition of fish bones to obtain calcium oxide (CaO) was conducted at various temperatures of 400, 500, 800, 900, 1000, and 1100 °C. The calcium oxide was then characterized using X-ray diffractometer, FTIR spectrophotometer, and SEM analysis. The calcium oxide obtained from the decomposition at 1000 °C was then used as a catalyst in the production of biodiesel from waste cooking oil. Diffraction pattern of the calcium oxide produced from decomposition at 1000 °C showed a pattern similar to that of the calcium oxide produced by the Joint Committee on Powder Diffraction Standard (JCDPS). The diffractions of 2q values …

Thermoeconomic Optimization Of Cascade Refrigeration System Using Mixed Carbon Dioxide And Hydrocarbons At Low Temperature Circuit, Nasruddin Nasruddin, Arnas Arnas, Ahmad Faqih, Niccolo Giannetti

Makara Journal of Technology

Many applications and industrial processes require very low cooling temperature, such as cold storage in the biomedical field, requiring temperature below -80 °C. However, single-cycle refrigeration systems can only achieve the effective cooling temperature of -40 °C and, also, the performance of the cycle will decrease drastically for cooling temperatures lower than -35°C. Currently, most of cascade refrigeration systems use refrigerants that have ozone depletion potential (ODP) and global warming potential (GWP), therefore, in this study, a cascade system is simulated using a mixture of environmentally friendly refrigerants, namely, carbon dioxide and a hydrocarbon (propane, ethane or ethylene) as the …

Developing Road Infrastructure Route Planning: Increasing Feasibility Of Toll Road Project, Mohammed Ali Berawi, Teuku Yuri Zagloel, Perdana Miraj, Abdur Rohim Boy Berawi, Wellsi Titaheluw, Saipol Bari Bin Abd Karim

Makara Journal of Technology

Indonesian government attempts to improve connectivity and to increase regional activities in Sumatera Island through the development of Trans Sumatera Toll Road (TSTR). However, despite its benefits to local economic development in Sumatera, the project shows low feasibility due to a low amount of investment. It can be attributed from the lack of planning in the initial phase to produce a comprehensive route that considers the various potentials of the regions. Thus, this research aims to investigate alternative route planning of Trans Sumatera Toll Road particularly in this paper for Central Sumatera by studying Gross Regional Domestic Product (GRDP), population …

Thermal And -Γ –Ray Irradiation Effects On The Ionic Conductivity Of (Licl)X(Montmorillonite)1-X, Safei Purnama, Aziz Khan Jahja, Takeshi Sakuma

Makara Journal of Technology

Compositesof montmorillonite (MMT) - lithium salts have been prepared using a simple process of powders mixing followed by heating. The powders resulting from this method are expected to beionic conductors with a high ionic conductivity characteristics. This characteristics is also further improved by employing gamma-ray irradiation technique at specified irradiation doses. The best results were obtained for the (LiCl)0.5(MMT)0.5 composite with a room temperature ionic conductivity of 2.192 mS/cm, which then increases to ~5 mS/cm after gamma irradiation at a dose of 400 kGy. This value is equivalent to the value of the ionic conductivity of current commercial rechargeable lithium …

The Design Of An Articulating Five-Headed In-Water Grooming Tool To Maintain Ships Free Of Fouling, Caglar Erdogan

Theses and Dissertations

Biofouling is a major concern to ship owners. Biofouling increases hull roughness, increasing the frictional resistance and fuel consumption while decreasing maximum speed. Finding a way to maintain hulls free from fouling has, therefore, become a research challenge for scientists and engineers. Grooming has been proposed as a novel method for controlling fouling (Tribou and Swain 2010). It refers to the regular proactive light cleaning to maintain the hull free of fouling with minimal impact to ship coatings. The purpose of this thesis is to design, build, and deploy a compliant multiheaded grooming tool which utilized five polypropylene vertically rotating …

Parametric Investigation Of A Laboratory Drop Test To Simulate Base Acceleration Induced By Wave Impacts Of High Speed Planing Craft, John D. Barber

Mechanical & Aerospace Engineering Theses & Dissertations

High speed operations in a small craft can be physically punishing and, in some circumstances, even dangerous for the crew. The aspect of small craft operations that make them punishing for the crew is wave slamming generated by wave impacts as the craft is traveling over the seas at high speed.

The initial step of this thesis effort was to perform a literature survey to determine what knowledge existed within the technical and academic community about wave slamming and simulating them with drop tests.

Eventually, a final experiment strongly influenced by the experiment model found in (Protocol 1, 2014) was …

Changing Trends In Wave Heights In The U.S. Mid-Atlantic Region, Hillary Lane

Civil & Environmental Engineering Theses & Dissertations

The pace and effects of climate change are an area of constant focus for coastal engineers as evolving patterns in the atmosphere worldwide affect the oceans and coasts on a regional and global scale. Surface waves respond to changing wind patterns both locally and from propagating swell, and the difficulty in predicting future wind patterns is well-established. Expectations that climate change will result in more frequent and intense coastal storms and consequently greater wave heights in the North Atlantic are still unrealized, and recent forecasts from a variety of atmosphere-ocean coupled global climate models instead predict decreasing wave heights through …

Quantification Of Frictional Drag Due To Biofouling On In-Service Ships, John Travis Hunsucker

Theses and Dissertations

The purpose of this research was to improve the quantification of frictional drag due to biofouling on in-service ships by advancing the knowledge and methodology used to study the interactions between fouling communities and the surrounding environment. This research examined the influence of hydrodynamic stress on the development and frictional drag of fouling communities that developed on a fouling release coating; investigated the reliability of using ship performance monitoring to detect changes in the hull and propeller condition; and evaluated the feasibility of developing a field deployable instrument capable of measuring the local frictional resistance on a ship hull in …

Study On Oil Palm Fresh Fruit Bunch Bruise In Harvesting And Transportation To Quality, Andreas Wahyu Krisdiarto, Lilik Sutiarso

Makara Journal of Technology

There are losses of production due to oil palm field’s material handling. Activities that may raise the losses are harvesting and transportation, which may cause bruise and damage to fruit. This research was aimed to learn the bruise of fresh fruit bunch (FFB) phenomenon in harvesting and transportation. Method used in this research was measuring the bruise area resulted by FFB falling when harvested, loading (throwing up) FFB to truck bin, and transporting using truck. These data, coupled with weight of bruised fruit, were calculated to get FFB bruise index. Each FFB bruise index is related to potential free fatty …

Automatic Arrhythmia Beat Detection: Algorithm, System, And Implementation, Wisnu Jatmiko, I Md. Agus Setiawan, Muhammad Ali Akbar, Muhammad Eka Suryana, Yulistiyan Wardhana, Muhammad Febrian Rachmadi

Makara Journal of Technology

Cardiac disease is one of the major causes of death in the world. Early diagnose of the symptoms depends on abnormality on heart beat pattern, known as Arrhythmia. A novel fuzzy neuro generalized learning vector quantization for automatic Arrhythmia heart beat classification is proposed. The algorithm is an extension from the GLVQ algorithm that employs a fuzzy logic concept as the discriminant function in order to develop a robust algorithm and improve the classification performance. The algorithm is tested against MIT-BIH arrhythmia database to measure the performance. Based on the experiment result, FN-GLVQ is able to increase the accuracy of …

Optimization Of Electricity Generation Schemes In The Java-Bali Grid System With Co2 Reduction Consideration, Farizal Farizal, Wenty Eka Septia, Amar Rachman, Nasruddin Nasruddin, Teuku Meurah Indra Mahlia

Makara Journal of Technology

This research considers the problem of reducing CO2 emissions from the Java-Bali power grid system that consists of a variety of power-generating plants: coal-fired, natural gas, oil, and renewable energy (PV, geothermal, hydroelectric, wind, and landfill gas). The problem is formulated as linear programming and solved using LINGO 10. The model was developed for a nation to meet a specified CO2 emission target. Two carbon dioxide mitigation options are considered in this study, i.e. fuel balancing and fuel switching. In order to reduce the CO2 emissions by 26% in 2021, State Electric Supply Company (PLN) has to generate up to …

Apparent Porosity And Compressive Strength Of Heat-Treated Clay/Iron Sand/Rice Husk Ash Composites Over A Range Of Sintering Temperatures, M. Nizar Machmud, Zulkarnain Jalil, Mochammad Afifuddin

Makara Journal of Technology

Novel composites of clay/iron sand/rice husk ash (RHA) have been developed. Electric furnace was used to perform heat treatment on the composites to study the effect of sintering temperature on their apparent porosity and compressive strength. Two types of RHA with different bulk density were prepared to gain an understanding of the influence of apparent porosity on compressive strength of the heat-treated composites over a range of sintering temperatures. Heattreated composites, made of clay/iron sand and clay/RHA, were also prepared as a referenced material. X-ray diffraction (XRD) analysis was further performed to comprehensively discuss the role of iron sand on …

The Effect Of Irradiation Of Fe And Ar Ion On The Surface Morphology Of Diamond Thin Film Related To The Magnetoresistance Property, Salim Mustofa, Setyo Purwanto, Kenji Mishima

Makara Journal of Technology

The irradiation of Fe and Ar ion was applied on the surface of diamond/Si thin film to know its effect on the morphology of thin film.The magnetoresistance property was also studied. Ion irradiation treatment using Fe ion followed by argon ion at the energy of 70keV and a dose of 1 x 1015 ion/cm2 have been conducted on the surface of two types of thin film, diamond/Si (111) and diamond/Si (100). Both thin films were made by using a CVD method, and the thickness of the thin film is 1000-nm. From simulations using the software called Stopping and Range of …