Manufacturing Commons^™

Microfluidic Technology And Application In Urinal Analysis, Jiwen Xiang

LSU Doctoral Dissertations

Microfluidic technology offers numerous advantages in minimizing and integrating the traditional assays. However, the lack of efficient control components of the microfluidic systems has been hindering the widely commercialization of the technology. The research work in this dissertation focused on the development of effective control components for microfluidic applications.

A linear peristaltic pump was firstly designed, fabricated, and tested for conventional microfluidics by synchronously compressing the microfluidic channel with a miniature cam-follower system in Chapter 2. The miniature cam-follower system and microfluidic chip was prototyped using three-dimensional (3D) printing technology and soft lithography technology. Results from experimental test showed that …

A 2-D Finite Element Modeling And Simulation Of 3-Roll Forming, Wenbo Zhao

LSU Master's Theses

Medium to large diameter carbon steel pipes are widely used in various applications such as gas and fluid transportation, tunnels construction and building construction. Based on manufacturing techniques and characteristics, they are mainly categorized into three categories: Seamless pipe, Butt-welded pipe and Spiral pipe. The forming of butt-welded and spiral pipe is often performed by a technique called 3-roller bending. While traditional trial-and-error method is costly, the geometry complexity, along with material nonlinearity makes exact theoretical analysis difficult unless heavy simplified assumptions are made. While the forming parameters in the 3-roller forming process of butt-welded pipe has been studied in …

Industrial Conveyors’ Taxonomy And Its Applications, A. Hoshimov, A. Rustamov, J. Rozzokov

Acta of Turin Polytechnic University in Tashkent

In any manufacturing processes includes a material handling equipment that can transport raw material or semi-finished products from the one workstation to another. Material handling equipment are designed based on the type of manufacturing product or the process. Therefore, engineers can easily make decision anaylsis while the selection of the most preferred type of industrial conveyors among others. This paper focuses on the industrial conveyors that classifies all available conveyor types. In this work is defined a review that covers most of the currently available literatures and conveyors types that describes industrial conveyors, types, characteristics and applications. A taxonomy is …

Rc Baja Car Suspension, Tyler Martin

All Undergraduate Projects

This year the Mechanical Engineering Technology Department at CWU is holding an R/C Baja car competition using the same rules as the ASME competition. The designed car must compete in three separate events: the slalom course, drag race, and obstacle course. By not only completing, but also being competitive in each of the events, the car will be deemed a success. Suspension and steering are two essential components of any R/C car, and was the main focus for this report. The suspension must be able to support the car in the event of impacts. In addition, the steering must be …

Slab Tipper, Thomas C. Durand

All Undergraduate Projects

Stone countertops are very heavy and fragile. When installing a finished countertop, up to six workers are required to lift the stone onto the countertop, risking their safety and possibly breaking the stone. The safety of both the workers and the stone are very important, so there needs to be a better way. NSI Solutions came up with an idea for a mechanism to aid in the insulation process while limiting the number of workers required, and keeping the workers safer while adequately supporting the stone to prevent it from breaking. Designing methods and calculations were done to ensure the …

Exercise Machine Generator, Duane Harbick

All Undergraduate Projects

Exercise “spinning bikes” and bicycle training stands are common ways to maintain fitness and train for cycling. This exercise necessitates the user putting work into the machine by means of pedaling. In many instances the work put into exercise bikes and training stands is not taken advantage of. The objective of this project is an attempt to make use of some of the energy that a person would usually expend during exercise by building a generator that interfaces with multiple spinning bikes and training stands. It uses a synchronous pulley system to interface with the exercise machine and spin a …

Asme Rc Baja Challenge: Suspension And Steering, Hunter W. Jacobson

All Undergraduate Projects

The American Society of Mechanical Engineers (ASME) usually hosts an RC Baja challenge each year, testing a RC car in three events: slalom, acceleration and Baja. Although ASME will not be holding an event this year, CWU will be holding a similar event with three RC Baja car teams from CWU. The RC car that is tested in these events is designed and manufactured typically in teams of two. The RC car that each team submits must be able to complete these events while also remaining competitive. One part of great importance for the RC car is the suspension and …

Cwu Bottle Opener Manufacturing, Austin Sanford

All Undergraduate Projects

Previous students from the Mechanical Engineering Technology program came up with a method to help raise funds and awareness for the program. The idea was to manufacture and sell CWU bottle openers. However, a more efficient manufacturing method was needed. The aspect of the process that would have the most impact on the manufacturing time and material efficiency was the CNC machining of the parts. There were many potential variables to change to improve the process, but the main changes were to the cutter speeds and stock material size. Consequently, the changes made to stock material size reduced the number …

Asme R/C Baja Car, Torrie Large

All Undergraduate Projects

How does one build a car? Do they start with the tires and build inward or do they develop separate aspects at the same time? This remote-controlled car was designed and built with the intention of competing in the annual Baja Competition. There are three competitions: sprinting, slalom, and an obstacle course. The suspension system of this car must be designed to support the car for both the physical build and the competitiveness. It must do this without interfering with the drive train and steering mechanism designed by Doug Erickson. The suspension system employs suspension arms attached to the chassis …

Cassette Lockring Removal Tool, Kyle Wright

All Undergraduate Projects

Removal of a bicycle cassette requires additional tools to hold the cassette in place while loosening the cassette lockring. Typically a tool called a chain whip is used to stabilize the cassette, but is difficult to quickly and correctly apply to the cassette. Due to the need for an additional tool to hold the cassette, the user is faced with utilizing both hands while still needing to somehow hold the wheel in place. The lockring is torqued relatively tight and the overall combination of force, ergonomics, and number of tools required makes the task difficult to perform quickly. The objective …

H.F. Hauff Pruner Cutting Blades, Wyley Stewart

All Undergraduate Projects

Apple orchards are a critical component of agriculture in the United States, and keeping the apple trees in the best shape for optimum growth and production is hard work. Neil Hauff, an agriculture industry expert, challenged students at CWU to engineer a power assisted tree pruner. Across the country, apple orchards need pruned every season. The pruning of the trees is strenuous manual labor that requires many man hours. The proposed solution is to create a power assisted tree pruner that would minimize the amount of work needed to trim each tree branch. This project has been separated into three …

Enhancement Of Performance Of Micro Direct Ethanol Fuel Cells By Structural Modification, Sindhuja Valluri

Masters Theses

“Direct Ethanol Fuel Cells (DEFC’s) are becoming more important in current energy conversion devices because of their higher efficiency compared to other fuel cells. However, the performance of current DEFC’s is not efficient in providing energy to meet increasing energy demand. The objective of this work is to make the cell compact and at the same time improve performance. For this purpose, we have removed gasket and endplates to make structure compact and increased surface area by developing a new corrugated structure. This work also uses 3D printing technology Fused Deposition Modeling (FDM) to make pocket backing case to improve …

Stochastic Bi-Level Optimization Models For Efficient Operating Room Planning, Amin Abedini, Wei Li, Honghan Ye

Mechanical Engineering Faculty Publications

Within a hospital, the operating room (OR) department has the largest cost and revenue. Because of the aging population, the demand for surgical services has been increasing sharply in recent years. At the other hand, the rate of OR capacity expansion is lower than the rate of increasing demand. As a result, OR managers must leverage their resources by efficient OR planning. OR planning is challenging because of multiple competing\conflicting objectives such cost minimization and throughput maximization. Inherent uncertainty in the surgical procedures and patients arrivals complicate the decision making process. This increases the risk of non-realization of the system …

Damage Characterization Of Aircraft Fuselage Using Vibrothermography Technique-Review And Analysis, Abbasali Saboktakin

International Journal of Aviation, Aeronautics, and Aerospace

Vibrothermogrphy is a promising non-destructive technique that uses ultrasonic elastic waves to detect damages and is typically applied in the aerospace and automotive industries. This technique allows for defect selective imaging using thermal waves that are generated by ultrasound waves. In this paper, vibrothermography technique was applied to the aircraft fuselage to detect its damage. The influence of the damage on the temperature distribution at the damage region on the aluminum was investigated by finite element technique. Comprehensive understanding in edge crack in fuselage heating caused by local friction between crack surfaces was obtained.

Development Of Ceramic 3d Printer Using Cold-Based Extrusion, Noah Naden

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Optimal Sintering Temperature Of Ceria-Doped Scandia Stabilized Zirconia For Use In Solid Oxide Fuel Cells, Amanda K. Assuncao

Honors Undergraduate Theses

Carbon emissions are known to cause decay of the Ozone layer in addition to creating pollutant, poisonous air. This has become a growing concern among scientists and engineers across the globe; if this issue is not addressed, it is likely that the Earth will suffer catastrophic consequences. One of the main culprits of these harmful carbon emissions is fuel combustion. Between vehicles, power plants, airplanes, and ships, the world consumes an extraordinary amount of oil and fuel which all contributes to the emissions problem. Therefore, it is crucial to develop alternative energy sources that minimize the impact on the environment. …

Regression Analysis Of Factors Impacting Problem Solving Engagement Within Lean Systems Implementation, David M. Parsley Ii

Theses and Dissertations--Mechanical and Aerospace Engineering

Organizations around the world have attempted to implement the concepts of the Toyota Production System (TPS), commonly referred to as Lean, with limited sustainable success. The central principles of TPS, continuous improvement and respect for people, are grounded in the Japanese values of Monozukuri and Hitozukuri. Monozukuri deals with creating or making a product, while Hitozukuri conveys the idea of developing people through learning. In order for organizations to adopt these values they must have a system that engages employees at all levels in applying problem solving to improve their work. This research uses organizational assessments obtained from a variety …

Bayesian-Integrated System Dynamics Modelling For Production Line Risk Assessment, Sudhir Punyamurthula

Theses and Dissertations--Mechanical and Aerospace Engineering

Companies, across the globe are concerned with risks that impair their ability to produce quality products at a low cost and deliver them to customers on time. Risk assessment, comprising of both external and internal elements, prepares companies to identify and manage the risks affecting them. Although both external/supply chain and internal/production line risk assessments are necessary, internal risk assessment is often ignored. Internal risk assessment helps companies recognize vulnerable sections of production operations and provide opportunities for risk mitigation.

In this research, a novel production line risk assessment methodology is proposed. Traditional simulation techniques fail to capture the complex …

The Kentucky Re-Entry Universal Payload System (Krups): Sub-Orbital Flights, James Devin Sparks

Theses and Dissertations--Mechanical and Aerospace Engineering

The Kentucky Re-entry Universal Payload System (KRUPS) is an adaptable testbed for atmosphere entry science experiments, with an initial application to thermal protection systems (TPS). Because of the uniqueness of atmospheric entry conditions that ground testing is unable to replicate, scientists principally rely on numerical models for predicting entry conditions. The KRUPS spacecraft, developed at the University of Kentucky, provides an inexpensive means of obtaining validation data to verify and improve these models.

To increase the technology readiness level (TRL) of the spacecraft, two sub-orbital missions were developed. The first mission, KUDOS, launched August 13th, 2017 on a Terrier-Improved Malamute …

Sustainable Living Factories For Next Generation Manufacturing, Yoram Koren, Xi Gu, Fazleena Badurdeen, Ibrahim S. Jawahir

Mechanical Engineering Faculty Publications

To be profitable and to generate sustainable value for all stakeholders, next generation manufacturers must develop capabilities to rapidly and economically respond to changing market needs while at the same time minimizing adverse impacts on the environment and benefiting society. 6R-based (Reduce, Reuse, Recycle, Recover, Redesign and Remanufacturing) sustainable manufacturing practices enable closed-loop and multi-life cycle material flow; they facilitate producing more sustainable products using manufacturing processes and systems that are more sustainable. Reconfigurable Manufacturing Systems (RMS) and its characteristics of scalability, convertibility, diagnosability, customization, modularity and integrability have emerged as a basis for living factories for next generation manufacturing …