Energy Systems Commons^™

A New Capacity Controller For A Direct Expansion Air Conditioning System For Operational Safety And Efficiency., Yudong Xia, Huaxia Yan, Shiming Deng, Ming-Yin Chan

Faculty of Science & Technology (THEi)

For achieving a balance between the operational safety and efficiency of a variable speed direct expansion air conditioning system, a new capacity controller that can not only simultaneously control indoor air temperature and humidity, but also select an optimized degree of superheat setting to properly balance the operational safety and efficiency has been developed, by adding a control module to a previously developed capacity controller. The core of the control module was an artificial neural network based model representing the known relationship between the inherent operational characteristics and operational stability of a variable speed direct expansion air conditioning system. Using …

Investigation On Solar Assisted Liquid Desiccant Dehumidifier And Evaporative Cooling System For Fresh Air Treatment., Yi Chen, Hongxing Yang, Yimo Luo

Faculty of Science & Technology (THEi)

The widely used semi-centralized air conditioning (A/C) system consisting of independent fresh air system and fan coil system suffers from huge energy consumption, especially for fresh air treatment. Therefore, a liquid desiccant dehumidifier and regenerative indirect evaporative cooling (LDD-RIEC) system is proposed for fresh air treatment. The fresh air is handled by the LDD-RIEC system in which no electricity-intensive compressor involves. The hot and humid fresh air is firstly dehumidified by LDD and then sensibly cooled by RIEC. The thermal energy captured by solar collectors is used for desiccant solution regeneration. Indoor return air is cooled by fan coils of …

Development And Experimental Study Of A Novel Plate Dehumidifier Made Of Anodized Aluminum., Tao Wen, Lin Lu, Chuanshuai Dong, Yimo Luo

Faculty of Science & Technology (THEi)

The falling film dehumidifier is a key component in the liquid desiccant cooling system (LDCS). However, the most commonly used metals, such as steel and aluminum, can hardly resist the erosion of liquid desiccant. It greatly limits the fabrication of compact dehumidifiers and hinders the promotion of LDCS. The present study introduced a novel falling film dehumidifier which was made by the metal of anodized aluminum. Experiments were carried out to compare the dehumidification performance between ordinary aluminum dehumidifier and anodized one. The influences of air temperature, mass flow rate, inlet humidity and solution temperature, mass flow rate, temperature on …

Further Development Of A Thermal Comfort Based Fuzzy Logic Controller For A Direct Expansion Air Conditioning System, Huaxia Yan, Yan Pan, Zhao Li, Shiming Deng

Faculty of Science & Technology (THEi)

The primary purpose of A/C is offering occupants with acceptable indoor thermal comfort levels. Thermal comfort is a complicated result of non-linear interactions between six parameters. However, many of current A/C systems solely control air temperature. Whenever anyone of the five parameters other than temperature varies significantly, an occupant may feel thermally uncomfortable. To address the issue, a comprehensive thermal comfort index should be used as regulator in A/C systems. One fuzzy logic controller is available. However, the approach to the fuzzy logic controller is complicated. In this paper, one previous established fuzzy logic controller is simplified for its real …

Exercise Machine Generator, Duane Harbick

All Undergraduate Projects

Exercise “spinning bikes” and bicycle training stands are common ways to maintain fitness and train for cycling. This exercise necessitates the user putting work into the machine by means of pedaling. In many instances the work put into exercise bikes and training stands is not taken advantage of. The objective of this project is an attempt to make use of some of the energy that a person would usually expend during exercise by building a generator that interfaces with multiple spinning bikes and training stands. It uses a synchronous pulley system to interface with the exercise machine and spin a …

Development Of An Indoor Multirotor Testbed For Experimentation On Autonomous Guidance Strategies, Kidus Guye

Electronic Theses and Dissertations

Despite the vast popularity of rotary wing unmanned aerial vehicles and research centres that develop their guidance software, there are only a limited number of references that provide an exhaustive description of a step-by-step procedure to build-up a multirotor testbed. In response to such need, the first part of this thesis aims to describe, in detail, the complete procedure to establish and operate an autonomous multirotor unmanned aerial vehicle indoor experimental platform to test and validate guidance, navigation and control strategies. Both hardware and software aspects of the testbed are described to offer a complete understanding of the different aspects. …

Pyrolysis Of Fiber-Plastic Waste Blends, Shreyas Kolapkar

Dissertations, Master's Theses and Master's Reports

The main objective of this work is to investigate fast pyrolysis of fiber and plastic feedstocks in order to understand the synergistic effect from their co-pyrolysis. In this on-going work, fiber, plastic and their blend are characterized and pyrolysis oil is produced from them in the fast batch pyrolysis reactor. Based on a heat transfer model it is shown that results of oil produced from batch reactor will be applicable to the continuous paddle reactor. From feedstock characterization, chlorine was observed particularly in the plastic feedstock. Thus, chlorine removal method using torrefaction and high shear mixing was implemented and was …

Electrical Response Of Thermoelectric Generator To Geometry Variation Under Transient Thermal Boundary Condition, Elias Yazdanshenas, Alireza Rezania, Meysam Karami Rad, Lasse Rosendahl

Mechanical & Aerospace Engineering Faculty Publications

A three-dimensional numerical model is applied in this study to illustrate the electrical response of a thermoelectric generator (TEG) during transient heat flux at the hot side. In this work, various types of thermal boundary conditions are considered to evaluate the performance of the TEG. Thus, a TEG under pulsed heat flux is studied numerically, and the numerical model is verified by experimental results. With the consideration of a defined reference geometry, different heat flux frequencies are applied in order to evaluate the corresponding electrical output by the TEG. In addition, variation of the module performance for various TEG leg …

Simulation Of Non-Premixed Ethylene-Air Crossflow Jet Flame, Jennifer Onyinye Chikelu

Electronic Theses and Dissertations

Computational fluid dynamics tool has been employed in the past to determine and analyze efficiency or performance in combustion engines and for combustion analysis. This paper represents a systematic investigation on the best model predicts the temperature and soot production in coflow jet flame, by applying various RANS turbulent model, soot models and radiation models in presence or absence of gravity. It also applies this model predicted in crossflow jet flame and investigates the velocity ratio (ratio of the velocity of fuel jet to the velocity of air stream) variation effect on temperature and soot production. ANSYS-Fluent CFD software tool …

Evaluation Of Wind Energy Forecasts: The Undervalued Importance Of Data Preparation, Gianni Goretti, Aidan Duffy

Conference papers

The evaluation of wind energy forecasts is a key task for those involved in the wind power sector, and the accurate evaluation of forecasts is fundamental to make informed decisions both in business and research. To evaluate the accuracy of a forecast, observed values must be compared against forecast values over a test period. At times, however, the actual generation of a wind farm can be affected by factors that are outside the scope of the forecast model. Evaluating a forecast using a data set that includes such out-of-scope observations might give a biased or inconsistent assessment. In the data …

Test 2196: John Deere 5115r Pfc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2192: John Deere 5090r Pfc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Modelling And Analysis Of Chevy Volt Gen Ii Hybrid Vehicle In Electric Mode, Kaushik Surresh

Dissertations, Master's Theses and Master's Reports

The technical report discusses the high fidelity modelling of the powertrain of Chevy Volt Gen II Hybrid Vehicle in the Electric Mode. The overall objective of the powertrain model was to predict total energy consumed within 5% of experimental data for different drive cycles in Charge Depleting Mode. The following powertrain elements were modelled in Matlab and Simulink using parameters and performance maps provided by General Motors: battery, E-Motor, TPIM power electronics, transmission auxiliary pumps and spin losses.

An electric circuit based dynamic model of the Li-ion battery was developed. Static models of the E Motor, TPIM inverter, transmission auxiliary …

Test 2207: Challenger Mt743, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2204: John Deere 5090m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2203: John Deere 9420rx, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2200a: New Holland Workmaster 70, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2200: Case Ih Farmall 70a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2194: John Deere 5100r Pfc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2191: John Deere 5090r Oc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …