Energy Systems Commons^™

Current Best Practices For High Performance, Deep Energy Retrofits In Florida Affordable Housing, Florida Solar Energy Center, Janet Mcilvaine

FSEC Energy Research Center®

In the fall of 2009, researchers at the Florida Solar Energy Center (FSEC) began working with affordable housing entities that were conducting major renovation projects in unoccupied, foreclosed homes. The study was funded by the Florida Energy Systems Consortium and the U.S. Department of Energy's Building America program. When components and equipment were being replaced because they were worn out, researchers provided savings projections for higher-efficiency choices. Savings were also projected for improvements that were strictly for energy efficiency, such as adding ceiling insulation. The best practices summarized in this document are a mixture of assessment, design, specification, quality assurance, …

Hers Index Scores As An Alternative Compliance Path For The 2015 Iecc, Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

The analysis presented here is an extension of a previous study on HERS Index Scores as they relate to various version of the International Energy Conservation Code (IECC) by the same author. This extension of the previous study is designed to examine the impact of advanced, ultra-high efficiency appliances and high efficiency HVAC systems on HERS Index Scores as they relate to reductions in the HERS Index Scores that may be used as 'tradeoffs' against best practice envelope efficiencies.

A Parametric Study On Power Variation For Model Wind Turbine Arrays, Dominic Delucia

Dissertations and Theses

This thesis presents the results of wind tunnel experiments performed for various model wind turbine arrays. The aim is to understand how siting affects power output. To optimize wind farm efficiency the experiments vary the parameters of the model wind turbines and the layout of the wind turbine array. The parameters include the alignment, height, spacing, and the rotational direction of the model wind turbines. These experiments employ mechanical torque sensors to simultaneously measure the torque and rotor angular velocity, which yields a direct measurement of the fluid mechanical power extracted by the turbine at multiple locations. For a 4 …

An Applied Numerical Simulation Of Entrained-Flow Coal Gasification With Improved Sub-Models, Xijia Lu

LSU New Orleans Theses and Dissertations

The United States holds the world's largest estimated reserves of coal and is also a net exporter of it. Coal gasification provides a cleaner way to utilize coal than directly burning it. Gasification is an incomplete oxidation process that converts various carbon-based feedstocks into clean synthetic gas (syngas), which can be used to produce electricity and mechanical power with significantly reduced emissions. Syngas can also be used as feedstock for making chemicals and various materials.

A Computational Fluid Dynamics (CFD) scheme has been used to simulate the gasification process for many years. However, many sub-models still need to be developed …

Aspen Plus Simulation Of Biomass Gasification In A Steam Blown Dual Fluidised Bed, Wayne Doherty, Anthony Reynolds, David Kennedy

Book/Book Chapters

The efficient utilisation of biomass resources is of utmost importance. Biomass gasification offers much higher efficiencies than combustion. Gasification is a process in which a fuel is converted to a combustible gas (syngas). A dual fluidised bed gasifier known as the fast internally circulating fluidised bed (FICFB) was selected. It has been demonstrated at industrial scale and data is readily available for model validation. An Aspen Plus model was developed to simulate the FICFB gasifier. The model is based on Gibbs free energy minimisation and the restricted equilibrium method was used to calibrate it. The model has been validated and …

Numerical Modeling Of Heat Pipe Radiator And Fin Size Optimization For Low And No Gravity Environments, Virginia Ruth Bieger

UNLV Theses, Dissertations, Professional Papers, and Capstones

A heat-pipe radiator element has been designed and modeled to study the efficiency of heat transfer for low and no gravity environments, like in lunar environments. The advantages of using heat pipe includes the significant weight reducing and heat transfer efficiency. The heat transfer can be enhanced by the use of condenser sections with attached fins.

A series of various geometries of solid fins and heat pipes with and without fins were modeled using FLUENT®. This was done to determine the validity of using a heat pipe in lieu of a solid fin projection. A heat pipe had a 25 …

The Next Step Toward Widespread Residential Deep Energy Retrofits, Florida Solar Energy Center, Janet Mcilvaine

FSEC Energy Research Center®

The Building America Partnership for Improved Residential Construction (BA-PIRC) has been working with affordable housing entities to identify cost-effective technical pathways to achieve energy savings levels of 30% and safeguard or enhance indoor air quality (IAQ), durability, and comfort (McIlvaine et al. 2012; Fairey and Parker 2012).

The Effect Of Microencapsulated Phase-Change Material On The Compressive Strength Of Structural Concrete, Chad Norvell, David J. Sailor, Peter Dusicka

Mechanical and Materials Engineering Faculty Publications and Presentations

Latent heat energy storage through phase-change materials (PCMs) is one possible strategy to control interior temperatures in buildings, improve thermal comfort, and passively reduce building energy use associated with heating and cooling. While PCMs integrated into building structure elements have been studied since the 1970s, challenges of integrating PCMs into building materials while maintaining their heat storage benefits have limited their application in practice. The recent introduction of microencapsulated phase-change materials provides the energy storage capability of PCMs in micron-scale, chemically-inert capsules that can be easily integrated into composite materials such as gypsum wallboard and concrete. The size and physical …

Heating Effects Through Harmonic Distortion On Electric Cables In The Built Environment, Kevin O'Connell

Doctoral

Under ideal circumstances, electric power supply voltage and current waveforms should be sinusoidal. However, this is very seldom the case in the built environment, due to the proliferation of non-linear loads. Examples of non-linear loads are those containing switched mode power supplies, reactors and electronic rectifiers/inverters. Common devices such as personal computers, fluorescent lighting, electric motors, variable speed drives, transformers and reactors and virtually all other electronic equipment are examples of non-linear loads. Non-linear loads are the norm in the built environment rather than the exception. Such loads produce complex current and voltage waves and simple spectral analysis of these …

Improvement Of Hydraulic Press For Vegetable Oil Expression In Rural Areas, I. P. Bateebe

Tanzania Journal of Engineering and Technology (TJET)

Cultivation of oil producing crops especially Jatropha and croton as source of vegetable oil for biodiesel production is being encouraged in rural areas. To recover oil from seed, manual press is the feasible method in rural areas where there is no electricity. Research was conducted to improve hydraulic oil press machine for rural application. Factors affecting oil recovery were found to be: moisture content of seeds, operating pressure, seed oil content, and the amount of seeds pressed per batch. Percentage oil recovery was improved by reducing diameter of press cylinder, hence increasing expression pressure, and either reducing amount of seed …

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

Design, Construction And Evaluation Of A Low Head Hydroelectric Turbine For Canals, Sean Phillip Ellenson

BioResource and Agricultural Engineering

Means of hydroelectric power generation today typically require state or federal funding, massive construction projects and high head differentials with the use of a dam. With thousands of miles of canals and waterways at our disposal, it is necessary to find a cost effective way of generating a substantial amount of power from low-head hydroelectric power sources.

This senior project details research on low-head hydroelectric power generation, along with the design, construction and evaluation of a twisted Savonius hydroelectric turbine. Sizing optimizations for a twisted Savonius turbine were performed, and the hydroelectric power generation unit was constructed, including a housing …

High Temperature Filter Test Unit Upgrades, Blair Frandeen, Will Schill, Erick Shewmaker, Joshua Turgeon

Mechanical Engineering

The purpose of this project was to improve the existing High Temperature Filter Test Unit (HTTU) by optimizing performance and adding new features. These features include viewing ports and a camera system for observation of tests, a leak detection system, and a flame impingement system. Additional considerations included improving the current operation of the HTTU by reducing test time and energy loss. The HTTU is designed to test High Efficiency Particulate Air (HEPA) filters at temperatures up to 1300 ˚F, creating conditions which simulate a fire in a chemical processing facility. The HTTU was originally built as a Cal Poly …

Design Of An Energy Efficient Virtual End Node Client Using Openadr2.0a And Smap, Kevin Navero

BioResource and Agricultural Engineering

Demand Response (DR) describes the set of actions taken to impose a reduction in electrical loads to stabilize the power grid and decrease costs. It is used when power grid emergencies or extremely high demand and congestion, threaten the electricity supply-demand balance. Automated Demand Response (ADR) describes a web-based control system that triggers DR events automatically by signaling other pre-programmed control systems. This project intends to use the OpenADR2.0 specifications provided by the OpenADR Alliance to construct an open source Virtual End Node (VEN) client to retrieve DR signals. The Simple Measurement and Actuation Profile (sMAP) software is also used …

Low Speed Alternator Design, Scott Merrick

Electrical Engineering

No abstract provided.

Micro Hydropower System, Christpher Neally, Ian Verstuyft

Electrical Engineering

The micro hydropower project strives to meet the needs of a specific village in northern Thailand in partnership with Engineers Without Borders. Specifically, the electrical side of the system must be designed to convert the mechanical power of a flowing river that is turning a turbine into sustainable and dependable power. Currently available hydropower systems will be considered, analyzed, and tailored to suit the specific needs of the community in need. The system to be designed will be flexible enough to demonstrate proof-of-concept with the limited maximum generable power in lab while having the ability to be easily scaled for …

Hvac Lab, Adrian Leon, Wes Allen

Mechanical Engineering

The Cal Poly Heating Ventilation and Air Conditioning (HVAC) Department was donated a fume hood so that it could be used for educational purposes in the lab. The fume hood was not fully set up and only ran in a constant volume mode; the fan ran at full speed with no feedback to reduce air flow. A fume hood can be opened or closed using the sash; air flowing through the sash opening must always be above a certain speed. As the sash is closed the opening grows smaller and the speed of the air increases. Two additional modes of …

Cal Poly Brocade Challenge 2013, Chandler Morehardt, Alexa Coburn, Juan Silva, Kerry Sun, Greg Wang, Raul Chagoya, Jd Torres

Architectural Engineering

No abstract provided.

Wind And Hydroelectric Power Simulation For The Dc House Project, Randy Lormand, Christopher Goloskie

Electrical Engineering

This project details the design and integration of a wind and hydroelectric power simulation system in correlation with the DC House Project. The simulator uses variable speed drives to rotate a DC motor which then drives a generator to produce output. This output is then regulated using a DC to DC converter which holds the voltage level constant making it easier to interface with other power sources for the house. The test results indicate that the simulator will be able to produce two separate power outputs that will provide at least 70 Watts of power in the acceptable speed range …

Rebounder Fatigue Test Machine, Caroline Reeves, Will Robertson, Ethan Flory

Mechanical Engineering

JumpSport, a company that designs and sells trampolines and trampoline accessories, has sponsored this senior project team to design, build, and test a trampoline fatigue test machine. The machine must simulate a person jumping on the trampoline to test the life of JumpSport’s fitness trampolines and kids’ trampolines. Partway through the design process, the objectives were altered and this senior project team was tasked with merging with another Cal Poly senior project group to create an all-inclusive test machine to accommodate both full-trampoline testing and individual bungee cord testing.

The final design is centered on a slider crank linkage driven …