Electro-Mechanical Systems Commons^™

Development Of A 2-Dof Robotic Uterus Manipulator, Jeremiah Eggleston, Nicole Pishnery, Siddharth Navaneetha Raj

Williams Honors College, Honors Research Projects

The objective for our senior design project was to design a better uterus manipulator to assist with hysterectomies. We worked with our advisor Dr. Sam Song from the university’s Mechanical Engineering department. There are a variety of uterus manipulators on the market currently, each with unique design features to make the manipulator safer and more effective (van den Haak et al, 2015). Our group’s design modifies and sets itself apart from manipulators currently on the market. Going off others’ attempts to make a better manipulator (Fournelis, 2022), the key modifications our design incorporates are an additional degree of freedom (for …

Intelligent Thermoregulation In Personal Protective Equipment, Alireza Saidi, Chantal Gauvin

Études primaires

With the prospect of deploying intelligent thermal management in protective equipment, strategies for integrating heating and cooling actuators with modular temperature controls and automatic temperature regulation systems based on feedback from the individual’s personal and environmental parameters are discussed. © 2024 by the authors.

Functional Verification Of Additively Manufactured Metallopolymer Structures For Structural Electronics Design, Nathan D. Singhal

Honors Undergraduate Theses

As an attempt to improve the overall cost-effectiveness and ease of structural electronics manufacturing, this study characterizes the mechanical and electrical responses of structures which are fabricated from a novel metallopolymer composite material by fused deposition modeling as they are subjected to quasi-static, uniaxial mechanical tension. Baseline values of tensile properties and electrical resistivity were first obtained via ASTM D638-22 standard testing procedures and linear sweep voltammetry (LSV), respectively. A hybrid procedure to measure in-situ mechanically dependent electrical behavior was subsequently developed and implemented. The mechanical and electromechanical testing was followed by the derivation of stochastic values for several mechanical …

Actuator Optimization And Control Of Pediatric Knee Exoskeleton For Community-Based Mobility Assistance: More Lightweight, More Affordable, And More Stable, Sainan Zhang

Dissertations and Theses

Lightweight and smart exoskeletons offer the potential to improve mobility in children. State-of-the-art pediatric exoskeletons are typically clinic-based since they are either tethered or portable but cumbersome, and their design is often not optimized across a range of environments and users. Child growth progressively alters key exoskeleton design requirements, yet no prior work investigated actuator optimization to accommodate child growth. Moreover, exoskeletons typically use the torque sensor or spring mechanics as exteroceptive feedback, but these torque sensing methods not only lead to extra cost and mass but also cause a small range of stable controller gains.

To facilitate pediatric exoskeleton …

Towards The Automation Of Post-Processing Of Additive Manufacturing Using Collaborative Robots, Logan Schorr

Theses and Dissertations

Despite the incredible potential that collaborative robots have, they are underutilized in several industries that could benefit greatly. These specialized fields, such as additive manufacturing, face challenges that can be solved with the use of robotics, including advanced computer vision, end-effector tooling, and process refinement. My research aims to utilize collaborative robots in an effort to solve the above stated problems, for the specific fields of additive manufacturing. Specifically within this field is the automation of post-processing; this is normally completely manual, as the tools for automation are not sufficiently developed to handle the flexibility required for additive manufacturing. This …

A Novel Magnetorheological Pump Concept For Insulin Delivery, Mohammad Towhidul Islam Rimon

College of Graduate Studies: Theses & Dissertations

Over the past 25 years, awareness of type 1 diabetes has significantly increased, leading to a comprehensive understanding of various aspects, including its genetics, epidemiology, and disease burden. According to the Type 1 Diabetic Index, about 8.7 million people around the world live with this long-term autoimmune disease characterized by insulin deficiency and resultant hyperglycemia. However, the increased availability and utilization of artificial pancreas systems could potentially save 673,000 lives by 2040. Although, the advancement of diabetes technology offers Type 1 diabetic patients more tools to enhance glycemic management and achieve effective outcomes, many patients are still hesitant to adopt …

Railroad Condition Monitoring Using Distributed Acoustic Sensing And Deep Learning Techniques, Md Arifur Rahman

College of Graduate Studies: Theses & Dissertations

Proper condition monitoring has been a major issue among railroad administrations since it might cause catastrophic dilemmas that lead to fatalities or damage to the infrastructure. Although various aspects of train safety have been conducted by scholars, in-motion monitoring detection of defect occurrence, cause, and severity is still a big concern. Hence extensive studies are still required to enhance the accuracy of inspection methods for railroad condition monitoring (CM). Distributed acoustic sensing (DAS) has been recognized as a promising method because of its sensing capabilities over long distances and for massive structures. As DAS produces large datasets, algorithms for precise …

Investigation Of Mechanically Fatigue Low-Frequency Energy Harvesting Effects On Isotropic Materials, Daniel J. Meade

College of Graduate Studies: Theses & Dissertations

This research project reports an exploratory investigation of energy harvesting effect on isotropic material that goes through low frequency mechanical fatigue. Energy harvesting is a growing field of study that can recycle ambient energy back into a system that would otherwise be lost. This is a significantly useful method for the ongoing energy crisis and provides an alternate route to design and upgrade systems to be more efficient and last longer than current system designs. However, it is time to investigate if there is any effect vibration-based energy harvesting has on the structure from which energy is being harvested. To …

Design, Fabrication And Characterization Of Zero Power Sensor/Harvester For Smart Grid Applications, Zeynel Guler

Mechanical Engineering ETDs

This study presents a flexible sensor/harvester device to be used in both electromagnetic sensing and energy harvesting applications for smart grids. When a current passes through a wire, the sensor detects the magnetic field created by that current. The sensor magnet interacts with the wire magnetic field resulting in a transfer of energy through the piezoelectric cantilever. Piezoelectric, conductive, magnetic, and magnetostrictive composite thin films were prepared to fabricate this device.

Initially, the magnet of the cantilever was optimized considering its shape, thickness, length, taper angle etc. via both simulations and experiments. Peak to peak voltage versus cantilever position graph …

Silver Sintering Reliability And Its Enhancement For Use In High-Density Power Modules, Alicia Medina Garcia

Graduate Theses and Dissertations

This master's thesis is dedicated to enhancing the reliability of silver sinter die attachments, a pivotal component within the dynamic realm of power electronics. The study is meticulously organized into four distinct chapters, each contributing to a comprehensive understanding of silver sinter die attachment reliability and its implications for contemporary electronic packaging. In Chapter 1, an introduction is provided to the significance of silver sinter die attachment in the context of power electronics, underlining the imperatives associated with miniaturization, weight reduction, and heightened efficiency. The compelling need to investigate die attachment properties, particularly in high-temperature and high-power-density environments, is emphasized. …

Investigating Mems Devices In Flow Conditions Relevant To Flow-Through Systems., Mohammad Shafquatul Islam

Electronic Theses and Dissertations

Advancements in microscale actuating technologies has substantially expanded the possibilities of interacting with the surrounding environment. Microstructures that deflect in response to mechanical forces are one of the largest application areas of microelectromechanical systems (MEMS). MEMS devices, functioning as sensors, actuators, and support structures, find applications in inertial sensors, pressure sensors, chemical sensors, and robotics, among others. Driven by the critical role of catalytic membrane reactors, this dissertation aims to evaluate enzyme activity on polymeric membranes and explore how fabrication methods from the field of Electrical and Computer Engineering (ECE) can incorporate sensing and actuation into these porous surfaces. Toward …

Cnc Retrofits, Fabian Samano, Murat Askin, Daniel Lonczak, Zane Campise

Mechanical Engineering

The Boxford CNC Lathe is a machine used for educational purposes. The goal of the CNC Retrofits project is to improve the Boxford MT2’s performance and functionality to enable Mr. Lonczak to manufacture customized ballpoint pens. Within this Final Design Review (FDR) document, we present design updates since the CDR and implementation/assembly techniques. This work culminates in a solution to Mr. Lonczak’s needs which is analyzed in three subsystems: main control, spindle position tracking, and user interface. Within this report, we show the results of each subsystem’s verification process. These results prove that the design concept was met by describing …

Thermal Resistance Characterization Of High-Voltage Sic Power Module, Landon Lemmons

Mechanical Engineering Undergraduate Honors Theses

Researchers within the University of Arkansas Electrical Engineering Research Department have embarked on a project aimed at enhancing the thermal performance of high-voltage power modules. To aid in the progress of this project, the design, and development of a thermal tester device are needed. The primary objective of this device is to determine the various thermal properties of high-voltage power modules that the electrical engineering department has developed. Additionally, the project aims to facilitate electrical loading tests on power modules and provide researchers with the means to calibrate the power module in terms of thermal load. This project also possesses …

Advanced Jet Impingement Cooling For Power Electronics, Reece Whitt

Graduate Theses and Dissertations

Convective heat transfer by jet impingement cooling offers a suitable solution for high heat flux applications. Compared to techniques that rely on bulk conduction in series with convection, direct liquid impingement reduces the thermal resistance between power device hot spots and the coolant. Using additive manufacturing processes, location specific jets can be integrated into high voltage power electronics systems. Custom manifolds can be designed to reduce pressure drop, while simultaneously fine-tuning the thermal management efficiency. Although capable of highly efficient cooling, static impingement devices must be designed for the worst-case cooling requirements for a transient power profile, possibly resulting in …

Accelerated Testing Of Solder Spheres Under Combined Temperature, Current, And Shear Stresses To Estimate Reliability, Collin Ruby

Graduate Theses and Dissertations

With the densification of power electronics in the pursuit of decreased size and weight and increased efficiency, the need to investigate the properties of solder in packages with higher working temperatures and power densities is becoming apparent. Many research groups have conducted accelerated testing using methods such as thermal aging, shear or tensile stress tests, or electromigration tests, but relatively little research exists that considers the impact of several stresses in a combined study. This work aims to produce a novel method for estimating the lifetime of SAC305 solder joints under a combined stress scenario, which more accurately depicts the …

Tagalong Trail, Sean Wahl, Jason Davis, Quinlan Stephens, Ryan Johnson, Vinh Vo

Mechanical Engineering

The Cal Poly mechanical engineering team working on the Path of Lights and Sounds for the Girl Scouts of California’s Central Coast has now completed their project. In the last quarter of their project, they were able to finalize their tile’s structural design while iterating through several electronics board designs. Through this iteration, they were able to create a final electronics board and designed a water-resistant enclosure to house the board. A new team member was added, allowing them to manufacture 28 tile structures and 30 electronics assemblies over the course of two and a half weeks. This proved to …

Integrated Actuator, David Hefter, Mathew Smith, Amanda Westmoreland, Akanksha Maddi

Mechanical Engineering

This Final Design Review document outlines the senior project design that we, a team of four mechanical engineering students at California Polytechnic State University, are developing for Charlie Refvem, a lecturer in the mechanical engineering department. The final design has undergone significant modifications since the Critical Design Review, such as a redesigned vertical shaft, material changes, and the incorporation of belt tensioners. These redesigns are thoroughly discussed in the context of testing and assembly error resolution.

The document outlines the detailed steps for the production and testing of the design verification prototype. This includes the procurement and manufacturing of components, …

Examining The Efficacy Of Using Irt As An Nde Method For Cfrp And Ztcfrp Composites, William Wyatt Taylor

Graduate Theses and Dissertations (2019 - present)

A film adhesive is commonly used to form the bond-line between composite parts. The bond-line's quality and performance can be affected by defects such as voids, impurities, and agglomerations. Identifying these defects is possible with non-destructive evaluation testing (NDE). In this thesis, the joule-heating effect (JH) through carbon nanofiber (CNF) and carbon nanotube (CNT) modified film adhesive bonded to control carbon fiber reinforced polymer (CCFRP) was used along with infrared thermography testing (IRT) for bond-line defect inspection as a preliminary study. Due to the difference in the electrical conductivity between the modified epoxy and the defect, JH can cause a …

Improving Hexapod Platform Pose Accuracy - A Photogrammetry-Based Approach, Sourabh Karmakar

All Dissertations

The aim of this research is to make a newly constructed Stewart-Gough Platform-based test frame Tiger 66.1 operational by developing control software and estimating the error in its pose accuracy. The accuracy of the platform is affected by one source or multiple sources. The typical error sources are kinematic and structural, some of them originate from manufacturing imperfections, assembly deviations, elastic deformations, thermal deformations, and joint clearances which change the expected kinematic behavior of the manipulator. Also, some non-mechanical errors like transmission error, sensor accuracy, algorithm error, and truncation error in calculation contribute significantly in some cases. Using pose deviations …

Damage Detection With An Integrated Smart Composite Using A Magnetostriction-Based Nondestructive Evaluation Method: Integrating Machine Learning For Prediction, Christopher Nelon

All Dissertations

The development of composite materials for structural components necessitates methods for evaluating and characterizing their damage states after encountering loading conditions. Laminates fabricated from carbon fiber reinforced polymers (CFRPs) are lightweight alternatives to metallic plates; thus, their usage has increased in performance industries such as aerospace and automotive. Additive manufacturing (AM) has experienced a similar growth as composite material inclusion because of its advantages over traditional manufacturing methods. Fabrication with composite laminates and additive manufacturing, specifically fused filament fabrication (fused deposition modeling), requires material to be placed layer-by-layer. If adjacent plies/layers lose adhesion during fabrication or operational usage, the strength …