Structural Materials Commons^™

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Data

Corresponding data set for Tran-SET Project No. 18CNMS01. Abstract of the final report is stated below for reference:

"This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that …

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Publications

This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that locally produced UHPC has excellent mechanical and durability properties. UHPC has also been shown to have good bonding …

Disaster Resilient And Self-Assessing Multifunctional Transportation Structures, Ibrahim Karaman, Darren Hartl

Data

Corresponding data set for Tran-SET Project No. 18STTAM02. Abstract of the final report is stated below for reference:

"This research designs and characterizes multifunctional materials, in particular inexpensive shape memory alloys, for transportation structures that possess excellent mechanical properties and self-sensing capabilities for strengthening and health monitoring. The properties are the Fe-SMAs are sensitive to part size in that the grain size of the material, which can be grown to several inches, should exceed the smallest dimension of the part. In the current work, maximum part size of the large dimension Fe-SMA rods were determined through detailed microstructural investigations. Samples …

Oxidation Behavior Of Zirconium Alloys In Transient Conditions, Jordan Lee Vandegrift

Boise State University Theses and Dissertations

The effect of sample geometry, welding strategies, atmosphere, plastic deformation, and rapid heating on the oxidation behavior of zirconium alloys has been investigated in this work. The goal of this work was to determine which zirconium alloy would be best suited as nuclear fuel cladding material in the Transient Reactor Test (TREAT) facility at the Idaho National Laboratory (INL), which has unique operating conditions compared to typical reactors. TREAT is air-cooled, operates at high temperatures (400-600 °C), and produces rapid transients (≤ 700 ^°C/_s). Additionally, TREAT’s cladding geometry is unique in that it has chamfers and welds. …

Workforce Development Symposiums For Uhpc, Brad Weldon, Craig Newtson, Grace Mcmurry, Leticia Davila

Publications

Ultra-high performance concrete (UHPC) is a cementitious material with a dense microstructure that contributes to high compressive strengths as well as enhanced durability properties. UHPC also possesses significant post-cracking strength and ductility due to the addition of fibers. These characteristics produce a material that provides advantages over conventional concrete; however, high costs attributed to materials and production, lack of industry familiarity and knowledge, and the absence of standardized design procedures have impeded its widespread use. To help disseminate knowledge on UHPC, two workforce development symposiums on UHPC were held in Las Cruces, New Mexico. The symposiums consisted of presentations and …

Disaster Resilient And Self-Assessing Multifunctional Transportation Structures, Ibrahim Karaman, Darren Hartl

Publications

This research designs and characterizes multifunctional materials, in particular inexpensive shape memory alloys, for transportation structures that possess excellent mechanical properties and self-sensing capabilities for strengthening and health monitoring. The properties are the Fe-SMAs are sensitive to part size in that the grain size of the material, which can be grown to several inches, should exceed the smallest dimension of the part. In the current work, maximum part size of the large dimension Fe-SMA rods were determined through detailed microstructural investigations. Samples were subjected to abnormal grain growth heat treatments and found out that part size be increased up to …

Synthesis Of Amorphous Hydrogenated Boron Carbide From Orthocarborane Using Argon Bombardment: A Reaxff Molecular Dynamics Study, Nirmal Baishnab

Graduate Theses/Dissertations

In this study, the synthesis process of a-B­_xC:H_y using argon bombardment from the orthocarborane precursor was modeled by using reactive molecular dynamics (MD). Utilizing the MD simulations, the formation of free radicals as a result of ion bombardment was identified and quantified. Then, the densification process that is aided by the mixture of free radicals and orthocarborane was analyzed. The densification process by creating the initial structure composed of free radicals and orthocarborane with active sites created by partially removing some of the hydrogen atoms from the icosahedral cage was also modelled. Overall, a better understanding of …

Stress Corrosion Cracking Resistance Of Cold-Sprayed Al 6061 Deposits Using A Newly Developed Test Fixture, Mala M. Sharma, Jeremy Schreiber, Timothy Eden, Victor Champagne

Faculty Journal Articles

The stress corrosion cracking (SCC) response of Al 6061 bulk deposits produced by high-pressure cold spray (HPCS) was investigated and compared to commercial wrought Al 6061-T6 material. Representative tensile coupons were stressed to 25%, 65% and 85% of their respective yield strength and exposed to ASTM B117 salt fog for 90 days. After exposure, the samples were mechanically tested to failure, and subsequently investigated for stress corrosion cracking via optical and scanning electron microscopy with energy-dispersive X-ray spectroscopy (EDS). The results were compared to the wrought Al 6061-T6 properties and correlated with the observed microstructures. Wrought samples showed the initiation …

High Enthalpy Storage Thermoset Network With Giant Stress And Energy Output In Rubbery State And Associated Applications, Jizhou Fan

LSU Doctoral Dissertations

In this study, a new shape memory thermoset network with giant stress and energy output in rubbery state is synthesized and studied firstly since the low output in stress and energy in rubbery state has been a bottleneck for wide-spread applications of thermoset shape memory polymers (SMPs). Traditionally, stress or energy storage in thermoset network is through entropy reduction by mechanical deformation or programming. We here report another mechanism for energy storage, which stores energy primarily through enthalpy increase by stretched bonds during programming. As compared to entropy-driven counterparts, which usually have a stable recovery stress from tenths to several …

Investigation Of Fundamental Principles Of Rigid Body Impact Mechanics, Khalid Alluhydan

Mechanical Engineering Research Theses and Dissertations

In impact mechanics, the collision between two or more bodies is a common, yet a very challenging problem. Producing analytical solutions that can predict the post-collision motion of the colliding bodies require consistent modeling of the dynamics of the colliding bodies. This dissertation presents a new method for solving the two and multibody impact problems that can be used to predict the post-collision motion of the colliding bodies. Also, we solve the rigid body collision problem of planar kinematic chains with multiple contacts with external surfaces.

In the first part of this dissertation, we study planar collisions of Balls and …

Effect Of External Expanded Polystyrene (Eps) Panels On Slabs Subjected To Impact Load, Yosra El Maghraby

Civil Engineering

No abstract provided.

Tuned Photomechanical Switching Of Laterally Constrained Arches, Matthew L. Smith, J Gao, A A. Skandani, N Deering, D H. Wang, A A. Sicard, M Plaver, L-S Tan, T J. White, M R. Shankar

Faculty Publications

Laterally constrained arches driven between stable states by light, represent a unique space for compliant mechanism design. Exploiting mechanical multistability can overcome limitations of functional photomechanical actuators, which include limited repeatability, actuation speed, and positioning characteristics. Here, the addition of lateral constraints to an elastic bistable arch system is proposed as a method for toggling between bifurcated states by controlling the location of actinic irradiation. This approach expands the design space for photomechanical, mutistable structures and actuators. Arch behavior as a function of system parameters is simulated, including conditions leading to multistability. An experimental demonstration and exploration of a constrained …

Processing Of Aluminum Foam Using A Double Replication Process, Luc Salvo, Sevara Mukhtarova

Acta of Turin Polytechnic University in Tashkent

The purpose of this paper is to look at the impact of small morphological variations on kinetic storage of infiltrated open-cell foams. For this a new production process was studied, and a general description of the process and its variants are given.

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

Evaluation Of Tensile Properties For Selective Laser Melted 316l Stainless Steel And The Influence Of Inherent Process Features, Paul Swartz

Master's Theses

Optimal print parameters for additively manufacturing 316L stainless steel using selective laser melting (SLM) at Cal Poly had previously been identified. In order to further support the viability of the current settings, tensile material characteristics were needed. Furthermore, reliable performance of the as-printed material had to be demonstrated. Any influence on the static performance of parts in the as-printed condition inherent to the SLM manufacturing process itself needed to be identified. Tensile testing was conducted to determine the properties of material in the as-printed condition. So as to have confidence in the experimental results, other investigations were also conducted to …

Modifying Casting Parameters To Improve The High Temperature Ductility Of Investment Cast Nickel-Based Superalloy Pwa 1455, Lars Alexander Hedin, Cole Magnum Introligator

Materials Engineering

PCC Structurals, an industry leader in superalloy investment castings, has observed inconsistencies in the stress rupture performance of polycrystalline nickel-based superalloy PWA 1455. PCC has changed their casting parameters to reduce the thermal gradient during cooling but have been unable to correlate these changes with an increase in stress rupture elongation. Metallographic examination of past samples indicated microstructures composed of non- equiaxed dendritic grains with mean diameter of .021 inches along the test axis. A similar study on polycrystalline superalloys has indicated that excessive superheat temperatures above the liquidus can result in large grains identical to those observed, limiting the …

Using Numerical Models Of Dewatering At Coal Ash Impoundments To Understand Cost And Schedule, Peter Bell, Joel Thompson, Don Fuller

World of Coal Ash Proceedings

No abstract provided.

Investigating Ccr Units And Evaluating The Physical Properties Of Ponded Ccr, David Skeggs, Zahra Aghazadeh, Rachel Combs

World of Coal Ash Proceedings

No abstract provided.

Demonstration Of “No Migration” Alternative Performance Standard For Ccr Facilities In Arid To Semi- Arid Regions Using Unsaturated Zone Modeling, James Aiken, Katy Lindstom

World of Coal Ash Proceedings

No abstract provided.

Coal Combustion Residuals Management Using Geotextile Containers- Considerations For Various Options, Randall Wilcox, Gregg Lebster, Bryan Hamilton, Thomas Stephens

World of Coal Ash Proceedings

No abstract provided.