Structural Materials Commons^™

Study On Pavement Performance Of Waterborne Epoxy Emulsified Asphalt And Its Application In Micro‐Surface, Jiang Hai, Liu Dachang

Journal of China & Foreign Highway

In order to improve the pavement performance at micro-surface, waterborne epoxy resin was used to modify the emulsified asphalt, and the compatibility, microstructure, mechanical properties, rheological properties, and pavement performance of mixtures of the modified emulsified asphalt were studied. The storage stability test shows that the epoxy emulsion has good compatibility with emulsified asphalt. With the increase in waterborne epoxy resin content, the modified emulsified asphalt tends to form an epoxy resin-dominated skeleton structure. At the same time, with the increase in waterborne epoxy resin content, the adhesion and mechanical properties of emulsified asphalt and aggregate are significantly improved. At …

Evaluation Of Anti‐Cracking Performance Of Recycled Concrete With Recycled Rubber/Sbs Composite Modified Asphalt, Li Xiaobin

Journal of China & Foreign Highway

In order to improve the crack resistance of recycled asphalt mixture, a new styrenic block copolymer (SBS)/rubber composite modified asphalt with excellent crack resistance was proposed for the regeneration of reclaimed asphalt pavement (RAP). Based on the creep of low temperature bending beam, confined temperature stress, and four-point bending fatigue test, the low temperature cracking resistance and fatigue cracking performance of composite modified asphalt and SBS-modified asphalt were studied. The results show that the addition of rubber can improve the low temperature and medium temperature crack resistance of recycled asphalt concrete, which may be related to the propagation of micro-cracks …

Study On Anti‐Scattering Performance Of Asphalt Concrete On Aggregate Scattering Pavement Of Highway, Yang Siyuan, Chen Guiliang

Journal of China & Foreign Highway

Due to the lack of quantitative evaluation methods for aggregate scattering degree of expressway asphalt pavement in China and abroad, according to the disease characteristics of surface layer spalling, this paper adopted the Cantabro standard dispersion test to sample the concrete of the section with aggregate scattering of Huangqunan Expressway (G3) in Zhejiang Province. The dispersion impact damage modes of the mixture with different severity were analyzed, and the anti-dispersion performance of concrete was evaluated by mass loss rate and water absorption rate. The results show that aggregate scattering will reduce the density of the concrete structure at the surface …

Study On The Effect Of Quicklime On The Properties Of Cold Mix Asphalt, Liu Tao, Yi Ming, Song Tao

Journal of China & Foreign Highway

The low initial strength of cold mixed asphalt mixture leads to the delay of traffic opening time, and the large void ratio leads to poor water stability and other problems, which seriously hinder the development of cold mixed environment-friendly construction mode. In this paper, based on the principle that the heat of quicklime in the presence of water promotes the rapid loss of water in the cold mixed mixture, the mixing test and cohesion test of the MS-3 slurry cold mixed asphalt mixture with quicklime were carried out to explore the influence of quicklime on the demulsification time and cohesion. …

Research On Design Process Of Toll Interchange‐Expressway In The Area Of Funiu Mountain, Zhang Jie, Yang Qing, Chai Xiaolong

Journal of China & Foreign Highway

Currently, the expressways under construction in Henan Province are mainly concentrated in the Funiu Mountain area in the west, such as Yaoshan–Luanchuan–Xixia Expressway, Xixia–Xichuan Expressway, Yingchi–Luanchuan Expressway, and Luanchuan–Lushi Expressway. These projects are characterized by complex terrain conditions, difficult design, large-scale engineering, and a cluster of long tunnels and grand bridges. Under such complex conditions, how to arrange the interchange reasonably and ensure the optimal project plan becomes the key point of successful project design. This paper summarized the typical characteristics of toll interchange in Funiu Mountain area in recent years and put forward the design process of design preparation, …

Variable Speed Limit Control Method For Highway Under Dense Fog, Sun Jiancheng, Qiao Jiaxing

Journal of China & Foreign Highway

In order to solve the problem of traffic safety on expressways under dense fog and change the original fixed speed limit measures, a variable speed limit control method based on the safe allowable speed was proposed. The speed limit value was calculated based on the regulations in road traffic safety law on the speed under dense fog by considering that the traffic law does not mention the road alignment conditions, road conditions, and other factors, and the monitor data was used to approximate replace the data of individual vehicles for data optimization, and the safe speed and safe distance of …

Study On Dynamic Allocation Optimization Of Highway Pavement Maintenance Funds, Zou Yi

Journal of China & Foreign Highway

The conflict between the lack of maintenance funds and the growth of maintenance demand restricts the improvement of highway pavement technologies. In this paper, the state space of pavement maintenance demand was defined by the technical condition of the pavement, and the state of demand under different maintenance measures was designed as a Markov decision process. The dynamic allocation optimization model of highway pavement maintenance funds was established, and the corresponding genetic algorithm was designed. Finally, an example was given to simulate the optimized model. The results show that the Markov decision process can dynamically allocate highway pavement maintenance funds, …

Influence Factors Of Deicing And Thaw Performance Of Asphalt Mixture With Low Freezing Point, Zhou Shuiwen, Lin Fang, Zhang Xiaohua, Zhang Lingbo, Jiang Haoqiu

Journal of China & Foreign Highway

The conductivity test was used to study the release law of thawing and deicing components. The freezing test was used to study the cooling law of the mixture, and the thawing rate test was used to study the thawing and deicing performance. The results show that the release of thawing and deicing components of materials with a low freezing point is temperature-dependent, and the release at the high temperature is 3.49–3.77 times that at the low temperature. The granular materials tend to dissolve in water, which results in the release rate of thawing and deicing components faster than that of …

Experimental Analysis On Recycling And Mechanical Properties Of Waste Cement, Chen Liang

Journal of China & Foreign Highway

In order to recycle waste cement, construction waste cement materials were collected in the laboratory, and they were crushed, ground, and heat treated to facilitate reuse. Then, the waste cement was combined with the commonly used active fly ash admixture to prepare a new cement material for test analysis. The results show that the new cement material produced by industrial by-product, fly ash and waste cement material is feasible. A small amount of construction waste cement material (about 5%) can increase the 28-day compressive strength of cement by more than 50%, and the compressive strength of the prepared building material …

Experimental Study On Characteristics And Stability Of Different Aged Steel Slag Aggregate, Zhang Hongri, Wang Guiyao, Feng Jian, Lan Tianzhu, Wu Tao

Journal of China & Foreign Highway

Steel slag aggregate has good building material properties, but the utilization rate of steel slag in road engineering is low at present. In this paper, the chemical composition, basic physical and mechanical indexes, f⁃CaO, f⁃MgO, pulverization rate, CRB expansion rate, and other indexes of open-air aged steel slag aggregate in Fangchenggang, Guangxi Province for 0, 6, and 12 months were studied. The results show that the physical and mechanical properties of steel slag aggregate basically meet the requirements of road base materials and subgrade fillers, but the indexes of f⁃CaO, pulverization rate, and CRB expansion rate of steel slag aggregate …

Study On Effect Of Fiber Stabilizers On Water Temperature Cycle Damage Resistance Of Drainage Asphalt Mixtures, Liu Fuming, Wu Di, He Qingde, Yang Zhiping

Journal of China & Foreign Highway

In order to study the effect of fiber stabilizer on the water temperature cycle damage resistance of drainage asphalt mixture, drainage asphalt mixture without fiber stabilizer and with wood fiber, polyester fiber, and basalt fiber, respectively, were compared through tests. By standard dispersion test and immersed dispersion test, the anti-spalling ability of the mixture was analyzed. Under the same asphalt condition, the standard dispersion loss of the drainage asphalt mixture was reduced to different degrees after adding fiber stabilizer, which could increase the anti-spalling property of the drainage asphalt mixture to some extent. The splitting, indirect tensile, and rutting tests …

Precious Plastics - Plastic Brick Machine Fabrication, Timothy Ukaobasi Kanu, Evi Paraskevi Troulis

Architectural Engineering

The goal of this research is to determine the structural parameters of the recycled plastic polypropylene when molded into bricks resembling CMU blocks. To accomplish this, three mechanisms had to be assembled: the shredder, the injector, and the 1x1 mold. A tensile and compression test were to be performed on the plastic brick, and the values would be used to compare the tensile and compressive strength of PP plastic bricks, as well as their modulus of elasticity and stress vs. Strain performance. These values would be analyzed to determine whether it would be feasible to build an entire plastic wall. …

Atomistic Simulation Studies Of Thin Film Growth And Plastic Deformation In Metals And Metal/Ceramic Nanostructures, Reza Namakian

LSU Doctoral Dissertations

Despite the significant improvements in manufacturing and synthesis processes of metals and ceramics in the past decades, there are still areas in which the procedure is still frequently more of an art or skill rather than a science. Therefore, systematic and combined experimental and computational studies are required to facilitate the development of techniques that offer thorough understanding of the events taking place during manufacturing and synthesis processes. With regard to these issues, it is paramount to address microscale characterizations and atomic scale understanding of the events during fabrication processes. One of the focuses of this study is unraveling fundamental …

Freespan Analysis For Subsea Pipeline Integrity Management Strategy, Nurul Hadi, Muhammad Helmi, Edo Cathaputra, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Abstract. Over a rough seabed or on seabed subject to scour, freespans can occur when contact between a subsea pipeline and the seabed is lost over an acceptable distance. When this exceeds the allowable freespan length, design stresses can be exceeded, and a vortex induced vibration (VIV) response can be initiated, resulting in the risk of fatigue failure. If this is not predicted and controlled properly, it will affect pipeline integrity, leading to expensive rectification and intervention work. Freespan analysis consisted primarily of a screening check in which the as-found freespans from Remotely Operated Vehicle (ROV) or multibeam Side …

Architecture Of Heptagonal Metallo-Macrocycles Via Embedding Metal Nodes Into Its Rigid Backbone, A.M.Shashika D. Wijerathna, He Zhao, Qiangqiang Dong, Qixia Bai, Zhiyuan Jiang, Jie Yuan, Jun Wang, Mingzhao Chen, Markus Zirnheld, Rockwell T. Li, Yuan Zhang, Yiming Li, Pingshan Wang

College of Sciences Posters

Metal-organic macrocycles have received increasing attention not only due to their versatile applications such as molecular recognition, compounds encapsulation, anti-bacteria and others, but also for their important role in the study of structure-property relationship at nano scale. However, most of the constructions utilize benzene ring as the backbone, which restricts the ligand arm angle in the range of 60, 120 and 180 degrees. Thus, the topologies of most metallo-macrocycles are limited as triangles and hexagons, and explorations of using other backbones with large angles and the construction of metallo-macrocycles with more than six edges are very rare.

In this study, …

Investigation Of Fiber Orientation And Mechanical Properties Of Pyrolysis Recycled Carbon-Fiber Reinforced Thermoset Composite, Reva N. Simmons, Harry Lee, Garam Kim

Discovery Undergraduate Interdisciplinary Research Internship

With increasing demand of carbon fiber reinforced fiber thermoset composites, establishing a sustainable cycle for these materials becomes crucial. Pyrolysis is a process of reclaiming carbon fiber from thermoset composites by thermally degrading the polymer at high temperatures allowing the fibers to be extracted. Carbon fiber reclaimed through current pyrolysis processes for thermoset composites typically loses its original shape and orientation, making it difficult to reorganize the fibers. This study investigated the feasibility of maintaining the fiber orientations for continuous fiber reinforced thermoset composite during pyrolysis by stitching the carbon fiber layup to a conformable copper mesh during the manufacturing …

Predicting Dissolution Kinetics Of Tricalcium Silicate Using Deep Learning And Analytical Models, Taihao Han, Sai Akshay Ponduru, Arianit Reka, Jie Huang, Gaurav Sant, Aditya Kumar

Electrical and Computer Engineering Faculty Research & Creative Works

The dissolution kinetics of Portland cement is a critical factor in controlling the hydration reaction and improving the performance of concrete. Tricalcium silicate (C₃S), the primary phase in Portland cement, is known to have complex dissolution mechanisms that involve multiple reactions and changes to particle surfaces. As a result, current analytical models are unable to accurately predict the dissolution kinetics of C₃S in various solvents when it is undersaturated with respect to the solvent. This paper employs the deep forest (DF) model to predict the dissolution rate of C₃S in the undersaturated solvent. The …

Predicting Compressive Strength And Hydration Products Of Calcium Aluminate Cement Using Data-Driven Approach, Sai Akshay Ponduru, Taihao Han, Jie Huang, Aditya Kumar

Electrical and Computer Engineering Faculty Research & Creative Works

Calcium aluminate cement (CAC) has been explored as a sustainable alternative to Portland cement, the most widely used type of cement. However, the hydration reaction and mechanical properties of CAC can be influenced by various factors such as water content, Li₂CO₃ content, and age. Due to the complex interactions between the precursors in CAC, traditional analytical models have struggled to predict CAC binders' compressive strength and porosity accurately. To overcome this limitation, this study utilizes machine learning (ML) to predict the properties of CAC. The study begins by using thermodynamic simulations to determine the phase assemblages of …

A Deep Learning-Informed Design Scheme For Shear Friction At Concrete-To-Concrete Interface: Recommendations For Inclusion In Aashto Lrfd Guidelines, Tarutal Ghosh Mondal, Nikkolas Edgmond, Lesley Sneed, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Recent advancements in construction technology have led to high-strength concrete and steel. However, these developments have depreciated the accuracy of the design equations in current provisions, which were based on normal-grade materials. To fill such a research gap, this study presents a novel deep learning-based computation scheme that can replace the current design provisions by virtue of its superior accuracy and reliability. The proposed approach exploits Neural Additive Models (NAMs) in which geometric and material properties associated with a normal weight concrete-to-concrete shear interface are inputted to individual neural network blocks. The outputs of the individual blocks are linearly combined …

Development Of Inconel 718f And Inconel 718e Powders For Parts Manufacturing Utilizing Binder Jet Three-Dimensional Printing And Compressed Pellet Methods, Duncan Eric Manor Ii

Graduate Theses, Dissertations, and Problem Reports (ETD)

Alloy Inconel 718 is a Ni based superalloy used for high temperature applications including turbine blades, turbocharger rotors and nuclear reactors. Inconel 718 is a popular commercial atomized powder that has limitations in performance for use in additive manufacturing applications due to poor part quality and efficiency of current fabrication methods. Developing new compositions and additive manufacturing (AM) methodologies of IN718 is critical to improve the quality and the efficiency of IN718 parts manufacturing. Developing new additive manufacturing methodology that produces higher quality parts made of IN718 as compared to current methods has the potential to greatly impact industry, academia, …