Polymer and Organic Materials Commons^™

Two New Finite Element Schemes And Their Analysis For Modeling Of Wave Propagation In Graphene, Jichun Li

Mathematical Sciences Faculty Research

© 2020 The Author(s) In this paper, we investigate a system of governing equations for modeling wave propagation in graphene. Compared to our previous work (Yang et al., 2020), here we re-investigate the governing equations by eliminating two auxiliary unknowns from the original model. A totally new stability for the model is established for the first time. Since the finite element scheme proposed in Yang et al. (2020) is only first order in time, here we propose two new schemes with second order convergence in time for the simplified modeling equations. Discrete stabilities inheriting exactly the same form as the …

Practical Adhesion Measurements In Organic Coatings; Advancing Understanding And Mechanical Methods Development, Diana Gottschalk

Dissertations

“Adhesion” can be considered either a mechanical or chemical phenomenon. The mechanical interpretation describes the difficulty of separating surfaces and is useful for quantifying performance within applications that depend on bulk and interfacial properties. Chemical adhesion describes interfacial resistance to chemical attack and does not depend on bulk properties. Predicting chemical failure through mechanical measurement is confounded by the influence of bulk properties. However, the prospect is attractive because of the robust tolerance for sample geometries, allowing experiments to resemble an end-use system. The present work's primary goal was to elevate mechanical methods to provide a detailed interfacial characterization of …

Adhesion And Deformation Mechanisms Of Polydopamine And Polytetrafluoroethylene: A Multiscale Computational Study, Matthew Brownell

Graduate Theses and Dissertations

Polydopamine (PDA) has been shown to bond via covalent bonding, van der Waals forces, and hydrogen bonding and is known to adhere strongly to almost any material. The application of PDA between a substrate and a PTFE surface coating has resulted in low friction and a greatly reduced wear rate. Previous research probing the capabilities and limitations of PDA/PTFE films have studied the wear and mechanical properties of the film, but the overall adhesive and deformation mechanisms remain unclear.

In this research, we investigate the tribological properties of PDA and PTFE molecules and composites from the atomic to the microscale …

Direct Solar Absorption Nanoparticle Doped Membranes For A Hybrid Membrane Distillation And Photovoltaic Cell, Alejandro Espejo Sanchez

Boise State University Theses and Dissertations

The growing demand for clean water supplies is driving the need for an innovative approach of water desalination. Developing a method for treating water with high salinities is possible with membrane distillation (MD). Additionally, MD is very attractive for pairing with solar energy due to the low temperature requirements. The integration of a membrane distillation system with a photovoltaic (PV) system will result in the co-production of electricity and clean water, thereby improving the economics of MD. Such a hybrid system will directly absorb thermal energy in the membrane for desalination while taking advantage of the spectrally selective nature of …

Spatially Directed Functionalization By Co-Electropolymerization Of Two 3,4-Ethylenedioxythiophene Derivatives On Microelectrodes Within An Array, Benjamin J. Jones, Carol Korzeniewski, Jefferson H. Franco, Shelley D. Minteer, Ingrid Fritsch

Chemistry & Biochemistry Faculty Publications and Presentations

Electrodeposited conductive copolymer films with predictable relative properties (quantities of functional groups for further modification and capacitance) are of interest in sensors, organic electronic materials and energy applications. Potentiodynamic copolymerization of films in aqueous solutions of two different thiophene derivatives, (2,3-dihydrothieno[3,4-b]dioxin-2-yl) methanol (1) and 4-((2,3-dihydrothieno[3,4-b][1,4]dioxin-2-yl)-methoxy)-4-oxobutanoic acid (2), containing 0.02 M total monomer (0, 25, 34, 50, 66, 75, 100 mol% 2), 0.05 M sodium dodecyl sulfate, and 0.1 M LiClO4, on gold microelectrodes in an array was investigated. Decreasing monomer deposited (m) from 0 to 100 mol% 2 is attributed to a decreasing pH that inhibits electropolymerization. Molar ratios of …

Growth And Characterization Of Semiconductor Materials And Devices For Extreme Environments Applications, Abbas Sabbar

Graduate Theses and Dissertations

Numerous industries require electronics to operate reliably in harsh environments, such as extreme high temperatures (HTs), low temperature (LT), radiation rich environments, multi-extreme, etc. This dissertation is focused on two harsh environments: HT and multi-extreme.

The first study is on HT optoelectronics for future high-density power module applications. In the power modules design, galvanic isolation is required to pass through the gate control signal, reject the transient noise, and break the ground loops. The optocoupler, which consists of a lighting emitting diode (LED) and photodetector (PD), is commonly used as the solution of galvanic isolation at room temperatures. There is …

Radiation Modified Chitosan/Polyvinyl Alcohol Film With Polyvinyl Pyrrolidone Coating For Heavy Metal Ion Removal, Norhashidah Talip

Student Works (2020-2029)

Chitosan (CS) / Polyvinyl Alcohol (PVA) films were obtained by solution casting method. To be used in the water treatment application, these film need to be improved in mechanical strength. In this study, 2% (w/v) chitosan and 5% (w/v) PVA were blend at different CS: PVA weight ratios (50:50, 70:30 and 90:10). These mixtures were then transformed into films by solution casting method. Mechanical properties of the films were evaluated using tensile strength test where, at 70:30 of CS: PVA ratio gave the best tensile strength. Therefore, this composition was selected to proceed with the radiation modification with Polyvinyl Pyrrolidone …

A Bibliometric Survey On Polymer Composites In Energy Storage Applications, Babaji Ghule, Meena Laad

Library Philosophy and Practice (e-journal)

Ceramic polymer composites have gained a significant place in energy storage applications for electrical capacitors due to their distinguished properties. There is a huge demand of capacitors with high energy density, high dielectric strength, negligibly low dielectric loss, light weight, chemically less reactive in energy storage applications. These requirements can be fulfilled by ceramic polymer composites only which exhibit all the above-mentioned characteristics. Considering the huge demand of such capacitors, it has attracted the attention of researchers around the world. The present work attempts to summarise all the research conducted on Polymer Composites for energy storage applications and provides an …

Ensemble Labeling Towards Scientific Information Extraction (Elsie), Erin Murphy

College of Computing and Digital Media Dissertations

Extracting scientific facts from unstructured text is difficult due to challenges specific to the ambiguity of the language, the complexity of the scientific named entities and relations to be extracted. This problem is well illustrated through the extraction of polymer names and their properties. Even in the cases where the property is a temperature, identifying the polymer name associated with the temperature may require expertise due to the use of acronyms, synonyms, complicated naming conventions and by the fact that new polymer names are being “introduced” to the vernacular as polymer science advances. While there exist domain-specific machine learning toolkits …

General-Purpose Coarse-Grained Toughened Thermoset Model For 44dds/Dgeba/Pes, Michael M. Henry, Stephen Thomas, Mone’T Alberts, Carla E. Estridge, Brittan Farmer, Olivia Mcnair, Eric Jankowski

Materials Science and Engineering Faculty Publications and Presentations

The objective of this work is to predict the morphology and material properties of crosslinking polymers used in aerospace applications. We extend the open-source dybond plugin for HOOMD-Blue to implement a new coarse-grained model of reacting epoxy thermosets and use the 44DDS/DGEBA/PES system as a case study for calibration and validation. We parameterize the coarse-grained model from atomistic solubility data, calibrate reaction dynamics against experiments, and check for size-dependent artifacts. We validate model predictions by comparing glass transition temperatures measurements at arbitrary degree of cure, gel-points, and morphology predictions against experiments. We demonstrate for the first time in molecular simulations …

Preparation And Characterisation Of Heat Treated Oil Palm-Empty Fruit Bunch/High Density Polyethylene Composites, Nordin Nur Afifah

Student Works (2020-2029)

Natural fibre composites (NFCs) are composite materials, in which the reinforcing fibres are derived from renewable and carbon dioxide neutral resources such as wood or plants. NFC can be made by replacing synthetic fibres with various types of natural fibres. Oil palm empty fruit bunch (OPEFB) fibre and oil palm mesocarp fibre are two important types of fibrous materials left in the palm-oil industry. In this study, EFB will be used as a reinforcement to the high-density polyethylene (HDPE). EFB was heat-treated at 180°C using vacuum oven for one hour, extrusion compounded with HDPE at 10%, 20% and 30% weight …

Effect Of Nanofiller Coating And Loading On Facial Elastomer Physical Properties, Rahmi K. Aulia

Theses & Dissertations

Current materials used for facial prostheses are far from being desirable, and improved properties with “skin-like” feel are needed. This study evaluates property changes induced by sequential additions of uncoated and hydrophobic-coated nano-SiO₂ to polydimethylsiloxane (PDMS) and compares them with those measured for conventional submicron SiO₂-filled materials. Each filler type was sequentially added to vinyl-terminated PDMS at 0%, 0.5%, 5%, 10%, and 15% by weight. Tensile, tear, Durometer hardness, translucency and viscoelastic properties were evaluated, with hardness and translucency also evaluated following 3000 hours of outdoor weathering. Results demonstrated that 15% coated nano-SiO₂-filled PDMS materials …

Maleic Anhydride Compatibilized Peach Waste As Filler In Polypropylene And High Density Polyethylene Biocomposites, Caralyn Wong, Stephanie Jung, Joongmin Shin, Ajay Kathuria

Master's Theses

It is estimated that roughly 103, 515 tons of peach waste is produced annually in the US. The majority of the waste is disposed of in landfills, which contributes to climate change as they release 93 million metric tons of CO₂ equivalent. Peach waste principally consists of remaining stone and seed after flesh removal. The agro-waste includes both cellulose and lignin, which can be utilized as a filler in plastic packaging to reduce carbon footprints and material cost. The objectives of this research are (1) to develop peach flour (PF)-filled biocomposites with a polyolefin matrix using maleic anhydride-g-high density …

Alumina Ceramic Membrane Incorporated With Graphene Oxide Frameworks For Protein Recovery, Ishak Noor Fauziyah

Student Works (2020-2029)

Alumina ceramic membrane is undergoing rapid development and innovation for protein recovery process. However, the limitation of this membrane type is membrane fouling due to the deposition and adsorption of proteins on the surface and pore walls of the membranes. It is crucial to minimize membrane fouling by reducing interactions between protein and the membrane surface via surface modification technique. Thus, the main objective of this research is to develop an alumina membrane with enhanced antifouling property for protein recovery process. An alumina dope consisting of 57 wt.% alumina loading was used to fabricate two alumina membrane configurations; which are …

Tacky Elastomers To Enable Tear-Resistant And Autonomous Self-Healing Semiconductor Composites, Song Zhang, Yu-Hsuan Cheng, Luke Galuska, Anirban Roy, Matthias Lorenz, Beibei Chen, Shaochuan Luo, Yen-Ting Li, Chih-Chien Hung, Zhiyuan Qian, Peter Blake Joseph St. Onge, Gage T. Mason, Lewis Cowen, Dongshan Zhou, Sergei I. Nazarenko, Robson F. Storey, Bob C. Schroeder, Simon Rondeau-Gagné, Yu-Cheng Chiu, Xiaodan Gu

Faculty Publications

Mechanical failure of π-conjugated polymer thin films is unavoidable under cyclic loading conditions, due to intrinsic defects and poor resistance to crack propagation. Here, the first tear-resistant and room-temperature self-healable semiconducting composite is presented, consisting of conjugated polymers and butyl rubber elastomers. This new composite displays both a record-low elastic modulus (

Investigation Of Neoprene Medical Gloves: Analysis Of Material Properties, Durability, And Bacterial Barrier Efficacy, Amanda Agui

Honors Scholar Theses

This work aims to investigate the material properties, durability, and bacterial barrier efficacy of neoprene for applications in the healthcare/medical field. A special focus on material stiffness and fatigue failure will be explored. Additionally, manufacturer regulations and testing will be inspected to ensure medical gloves made of neoprene blends have a proper lifespan for its desired application in the healthcare community. The resistance of protective gloves and its ability to withstand perforation failure will be investigated to guarantee the safety of users holds extreme importance. Lastly, an analysis of the bacterial barrier efficacy of neoprene gloves will be determined.

Synthesis And Characterization Of Porous Carbon Composite Derived From Biomass Waste For Supercapacitor Application, Cheng Kim Sim

Student Works (2020-2029)

Energy storage devices have gradually dominated human daily activities and indispensable to economy development such as supercapacitor and battery. There are few factors determining the performance of supercapacitor and active material is one of the crucial. Therefore, biomass such as pineapple peel (PP) and green waste (GW) were preferred and prior mixed with manganese and tin carbonate to synthesize carbon composite (PP/GW-ZMO and PP/GW-ZTO) via combustion. Brunauer–Emmett–Teller (BET) was employed to study the textural properties with the highest specific surface area obtained in PP-C (1765.92 m2g-1) and GW-C (1613.92 m2g-1). The existence of composite materials was examined using x-ray diffraction …

Nature-Inspired Electrode Materials For Next Generation Sustainable Energy Storage, Mikhail Miroshnikov

Dissertations, Theses, and Capstone Projects

Despite revolutionizing the world of portable electronics, the contemporary lithium-ion battery (LIB) suffers from challenges associated with the cost, safety, and environmental impact of transition metal oxide-based intercalation cathodes. To alleviate these issues, naturally occurring organic molecules may serve as sustainable alternatives to traditional inorganic cathode materials. The electrochemical properties of organic compounds are derived from redox-active functional groups containing oxygen, nitrogen and sulfur. Additionally, these functional groups are capable of coordinating metal ions beyond lithium, allowing for compatibility with sodium-ion batteries (SIBs) and other earth abundant metal-based energy storage systems. However, despite competitive performance against commercialized cathode materials, much …

Fly Ash Based Geopolymer For High Temperature And High Compressive Strength Applications In Aggressive Environment, Aaryan Manoj Nair, Akm S. Rahman

Publications and Research

Geopolymers are the results of geosynthetic reactions between aluminosilicates and strong bases. This results in chemical bonds between aluminum (Al), Silicon (Si)and oxygen (O) composing polymer rings in tetrahedral coordination. These bonds give them widespread useful applications such as high heat bearing ceramics, and base construction material whilst being far more environmentally conscious. The purpose of the experiment is to examine the effect of Silicon Carbide whisker and inorganic glass particles on thermal and mechanical properties of Geopolymers. This study will help understand the effect of various compositions and concentrations of SiO₂ in mechanical strength. In this experiment, the …

Effect Of Post-Consumer Content And Bioplastic Incorporation On Polymeric Resin In Consumer Applications, Shelby Bicknell

Electronic Theses & Dissertations

Controversy surrounds the use of plastic products, primarily due to their potentially negative impact on the environment at the end of their lifecycle. The most widely used plastics are manufactured from petrochemicals such as petroleum, coal or natural gas. Petrochemical plastics are not able to readily breakdown in the environment, which aggravates the existing pollution problems. Fortunately, there are eco-friendly alternatives to petrochemical-based plastics. Bioplastics may be derived from renewable sources, biodegradable, or both. Bio-based plastics are plastics that may be derived from renewable biomass sources including, but not limited to, vegetable oils, cornstarch, straw, woodchips, and food waste. They …