Materials Science and Engineering Commons^™

A Sinteractive Ni-Bazr0.8Y0.2O3-Δ Composite Membrane For Hydrogen Separation, Shumin Fang, Siwei Wang, Kyle S. Brinkman, Fanglin Chen

Faculty Publications

BaZr_0.8Y_0.2O_3−δ (BZY) is an excellent candidate material for hydrogen permeation membranes due to its high bulk proton conductivity, mechanical robustness, and chemical stability in H₂O- and CO₂-containing environments. Unfortunately, the use of BZY as a separation membrane has been greatly restrained by its highly refractory nature, poor grain boundary proton conductivity, high number of grain boundaries resulting from limited grain growth during sintering, as well as low electronic conductivity. These problems can be resolved by the fabrication of a Ni–BZY composite membrane with large BZY grains, which requires the development …

Preparation And Electrochemical Performances Of Cofe2O4/Gns Nanocomposites As Anode Material For Lithium Ion Battery, Mo-Chao Cai, Sen-Rong Cai, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The CoFe₂O₄/GNS was synthesized by a simple one-pot solvothermal method. The results obtained by X-ray diffraction (XRD) and transmission electron microscopy (TEM) showed that the CoFe₂O₄ particles with sizes of 15 nm dispersed on the surface of graphene uniformly. Electrochemical tests indicated that the CoFe₂O₄/GNS nanocomposite exhibited excellent cyclic stability with almost 95.8% capacity retention after 100 cycles at the current density of 500 mA·g^-1 and delivered a high reversible capacity of 482 mAh·g^-1 at the current density of 2 A·g^-1.

Effects Of Carbon Interlayer On Electrochemical Performance Of Lithium-Sulfur Cell, Jin-Peng Yu, Ming Zhang, Fei Ding, Zhi-Yuan Tang, Xing-Jiang Liu

Journal of Electrochemistry

Three kinds of conductive carbon films were prepared with Super-P (SP), KB and MWCNTs, and then the as-prepared carbon films were applied as an interlayer between a sulfur electrode and a separator for constructing a coin-type lithium-sulfur (Li-S) cell, respectively. The assessment results show that all the cells delivered the reversible capacities higher than 800 mAh·g^-1 after 40 cycles when the sulfur loading was up to 80% (by mass) in the sulfur electrode. Due to significant differences of physical properties among the carbon materials, the cell with a KB interlayer exhibited higher electrochemical polarization; the cycling performance of the …

Electro-Catalytic Oxidation Of Hydrogen Peroxide On Au/ L-Methionine /Gc Electrode, Jian-Feng Fan, Xue-Mei Luo, Jing Li, Lou-Zhen Fan

Journal of Electrochemistry

The modified electrodes have been fabricated by generation of Au nanoparticle chains, which was produced by reaction between HAuCl4 and sodium citrate without any additional capping agents or surfactants. The self-assembled Au nanoparticles were attached to the surface of glassy carbon electrode (GCE) layer by layer, using L-methionine (L-Met), thiourea (TU), allyl thiourea (ATU) and polyvinylpyrrolidone (PVP) as a crosslinking agent, respectively. The experimental results showed that the electrochemical performance of the different modified electrodes varied in [Fe(CN)₆]^3-/4- solution. The Au/L-Met/GCE exhibited an excellent electrochemical property, which is superior to other modified electrodes. In addition, the catalysis …

Electrocatalytic Oxidation Of Glycerol At The Platinum Electrode Modified With An Nd-Fe-Moo42- Cyano-Bridged Mixed Coordination Polymer, Yong-Jun Ma, Yu-Xiu Tian, Jing Liu, Min Zhou, Jing Ding, Zhi-Mei Jin, Xiang-Mei Wang

Journal of Electrochemistry

A platinum electrode decorated with the ordered Nd-Fe-MoO₄^2- cyano-bridged mixed coordination polymer was successfully prepared by electrodeposition in virtue of the lyotropic liquid crystal soft template methods, and electrocatalytic oxidation behavior of glycerol was investigated on the chemically modified electrode by cyclic voltammetry. The influences of experimental factors such as the concentrations of H⁺ and SO₄^2- in electrolytes, glycerol concentration and scan rate on the electrocatalytic activity of glycerol at the modified electrode were also studied. It indicated that the proper amount of SO₄^2- in weakly acidic electrolyte could help to improve the …

Synthesis Of Platinum Nanocrystallites And Possible Electrocatalytic Properties For Methanol, Lei-Lei Lu, Bao-Zhong Du, Sha Sun, Jin-Fen Niu, Jie Zhao

Journal of Electrochemistry

Platinum nanocrystallites were synthesized by the colloidal method using oxamide as the stabilizer. The morphologies and electrocatalytic performances for methanol of platinum nanocrystallites prepared at different pH values and with different reactant ratios of precursor and stabilizer were investigated. It was found that the platinum nanocrystallites synthesized at pH=5 and with the reactant ratio of 1:20 showed the best electrocatalytic activity for methanol. The peak current density reached up to 1709 μA·cm^-2. Furthermore, the electrocatalytic activity of platinum nanocrystallites for methanol reduced significantly although the cyclic voltammograms in the blank solution were not obviously changed after exposing in …

Effect Of Temperature On The Self-Humidifying Open-Cathode Proton Exchange Membrane Fuel Cell, Si-Chen Zhao, Ben Wang, Qiu-Hong Jia, Ming Han, Yu-Hong Xie

Journal of Electrochemistry

Based on the experiments about the output characteristics of a home-made temperature-controlled PEMFC system with atmospheric pressure and no external humidifying condition in different loading voltages and operating temperatures, the optimum operating temperature at different loading voltages can be obtained by tracking the output characteristics of PEMFC operating over a range of temperatures. By analyzing the fitted data the kinetic parameters are evaluated and the effect of different operating temperatures on the PEMFC performance is discussed from a view of electrode kinetics.

3d Printing Of Stainless Steel For Engineering Applications, Michael Doyle

Undergraduate Research Symposium

3-D metal printing has the potential to solve problems in the medical, prototyping, automotive, aerospace, defense, and other engineering industries. To reach the potential of any manufacturing process, the final product’s material characteristics and how the process affects those characteristics must be understood to meet the demands of industrial applications. There is a gap in standard testing information regarding metal based 3-D metal printing processes. The purpose of this research is to fill that gap of valuable information for this manufacturing process, so that its principles can be used to design better products. Fundamental tensile and compression tests were executed …

Magnetic Shape Memory Micro-Pump For Intra-Cranial Drug Delivery, Sam Barker, Eric Rhoads, Andrew Morrison, Miranda Buttram, Paul Lindquist

College of Engineering Presentations

Magnetic shape-memory alloys exhibit strong magneto-structural coupling enabling large magnetic-field-induced deformation. Local control of twinning via variable inhomogeneous magnetic fields initiates local reversible deformation. Previous work produced a valve-less micropump consisting of a Ni-Mn-Ga single crystal, a casing, and a rod magnet. The micropump successfully pumped fluid in opposite directions when the magnet was turned clockwise and counter clockwise. Our current work modifies this micropump for application in rat a head stage, which would simultaneously monitor electroencephalograph data and deliver 0.5-5.0 μl of a drug solution at 100-500 nl/min directly to the rat’s brain. These improvements and the application of …

Molecular Modification Of Cnt Junctions, Kari Mclaughlin*, Hanna Meinikheim*, Angela "Nikki" Chang

College of Arts and Sciences Presentations

Carbon nanotube networks (CNNs) are increasingly finding applications as thin film transistors (TFTs), integrated circuits, and display drivers on flexible, transparent substrates. This is attributed to the higher carrier mobility of CNNs as compared to amorphous silicon and organic TFTs [1,2]. However, high electrical [3-5] and thermal [6,7] resistances at individual nanotube junctions (NJs) limit the performance of CNN devices. The resistances of the junctions are no less than an order of magnitude higher than those of individual carbon nanotubes (CNTs). This causes high power dissipation at the NJs. In the end this causes degradation of the overall device performance …

The Properties And Structure Of Zinc Magnesium Phosphate Glasses, Charmayne E. Smith (Lonergan), Richard K. Brow

Materials Science and Engineering Faculty Research & Creative Works

Zn-Mg-phosphate (ZMP) glasses, including those with the nominal molar compositions (50 - x)ZnO xMgO 50P₂O₅ (0 ≥ x ≥ 50) and (60 - y)ZnO yMgO 40P₂O₅(0 ≥ y ≥ 60), were prepared and properties such as density, refractive index, coefficient of thermal expansion and glass transition temperature (Tg), were measured. The glass transition temperature increases by 100-150 C and the room temperature dissolution rates in water decrease by 1-2 orders of magnitude when MgO replaces ZnO while maintaining a constant P₂O₅ content. Glass structures were characterized by Raman spectroscopy and …

Effect Of Ionic Crosslinking On The Swelling And Mechanical Response Of Model Superabsorbent Polymer Hydrogels For Internally Cured Concrete, Qian Zhu, Christopher W. Barney, Kendra Erk

School of Materials Engineering Faculty Publications

The chemical and physical structure-property relationships of model superabsorbent polymer (SAP) hydrogels were characterized with respect to swelling behavior and mechanical properties in different ionic solutions (Na+, Ca2+, and Al3+). The model hydrogels were composed of poly(sodium acrylate-acrylamide) (PANa-PAM) copolymer with varying concentrations of PANa (0, 17, 33, 67, and 83 wt.%) and covalent crosslinking densities of 1, 1.5, and 2 wt.%. By synthesizing the hydrogels in-house, systems with independently tunable amounts of covalent crosslinking and anionic functional groups were created, allowing for the relative effects of covalent and ionic crosslinking on the properties of the hydrogels to be directly …

Simulation Of The Relaxation Potential Profile Of An Ac-Dc-Ac Test, Kerry N. Allahar, Michael F. Hurley, Erik D. Sapper, Darryl P. Butt

Materials Science and Engineering Faculty Publications and Presentations

The relaxation period of the accelerated ac-dc-ac test for coatings is associated with the transient electrochemistry that occurs when the immersed coated system is allowed to return to a stable open-circuit condition after being subjected to a cathodic potential. A mathematical model of the transient electrochemistry that occurs during this relaxation period is presented for coated aluminum. Expressions for the corrosion potential and corrosion current as functions of the local pH at the metal-coating interface were developed using reported experimental results. These expressions enabled the simulation of the transient electrochemistry under the constraint of balanced anodic and cathodic current densities. …

Oxidation Kinetics Of Nicrofer-6025ht For Use In Elevated Temperature Electrochemical Devices, Tyler Cook, Alan Meier, Ph.D.

TECHxpo

Recent advances in high temperature electrochemical devices have prompted research into potential materials for component fabrication.

Processing And Characterization Of Zr-Based Metallic Glass By Laser Direct Depositon, Heehun Bae

Open Access Theses

Bulk Metallic Glass has become famous for its exceptional mechanical and corrosion properties. Especially, Zirconium has been the prominent constituent in Bulk Metallic Glass due to its superior glass forming ability, the ability to form amorphous phase with low cooling rate, thereby giving advantages in structural applications.

In this study, Zirconium powder was alloyed with Aluminum, Nickel and Copper powder at an atomic ratio of 65:10:10:15, respectively. Using the ball milling process to mix the powders, Zr65 Al10 Ni 10 Cu15 amorphous structure was manufactured by laser direct deposition.

Laser power and laser scanning speed were optimized to increase the …

Shear Rheological Characterization Of Gel Healing Response And Construction Of Rheo-Piv System, Abhishek Deepak Bawiskar

Open Access Theses

Thermo-reversible gels are solvent-filled 3D networks of polymer chains interconnected by physical (transient) crosslinks. On applying a high shear stress, the crosslinks are broken and these gels show a typical stress-strain behavior due to cohesive fracture of the gel. When heated above a critical temperature and cooled back to room temperature, all the crosslinks are re-formed. Interestingly, partial to full recovery of broken crosslinks is also observed by simply letting the gel stand at room temperature. In this study, the fracture and healing behavior of a model acrylic triblock copolymer gel has been characterized by shear rheometry. A mathematical model …

Effect Of Multivalent Ions On The Swelling And Mechanical Behavior Of Superabsorbent Polymers (Saps) For Mitigation Of Mortar Autogenous Shrinkage, Qian Zhu

Open Access Theses

The chemical and physical structure-property relationships of model superabsorbent polymer (SAP) hydrogels were characterized with respect to swelling behavior and mechanical properties in different ionic solutions (Na+ , Ca2+ , and Al3+ ). The model hydrogels were composed of poly(sodium acrylate-acrylamide) (PANa-PAM) copolymer with varying concentrations of PANa (0, 17, 33, 67, and 83 wt.%) and covalent crosslinking densities of 1, 1.5, and 2 wt.%. By synthesizing the hydrogels in-house, systems with independently tunable amounts of covalent crosslinking and anionic functional groups were created, allowing for the relative effects of covalent and ionic crosslinking on the properties of the hydrogels …

Design Of A Uv Curing Cartridge For 3d Inkjet Printing, Richard Wiswell

Thinking Matters Symposium Archive

In printing multi-layer electronic circuits, each layer must be formed as a continuous pattern in high resolution from ink jetted liquid droplets and be in precise alignment with the other layers, precluding substrate removal for UV curing. This research seeks to determine the optimal method for in-situ UV curing of the ink jetted material in a single pass. The inkjet replacement cartridge designed for this purpose was constructed of aluminum, fit into the printer head assembly in good alignment with the other ink cartridges, and contained a UV LED for in-situ curing and a cooling fan to maintain safe operating …

Section Abstracts: Astronomy, Mathematics, And Physics With Materials Science

Virginia Journal of Science

Abstracts of the Astronomy, Mathematics, and Physics with Materials Science Section for the 92nd Annual Meeting of the Virginia Academy of Science, May 13-15, 2014, Virginia Commonwealth University, Richmond, Virginia

Dynamic Characteristic Identification Of Seismic-Excited Multi-Story Buildings Through Response-Only Technique, Agung Budipriyanto, Priyo Suprobo

Makara Journal of Technology

Identifying dynamic characteristics of civil engineering structures is still a challenging task. It intends to assess behavior of the structures under time-dependent loads. This paper discusses a methodology suitable for identifying the characteristics of multi-story buildings using only their measured response under earthquake ground excitations. Appropriateness of technique used for structural identification was corroborated through coherence of the structure’s responses. The methodology was applied for identifying the characteristics of 14-story and 20-story office buildings located in a high seismic region. Responses of these two buildings recorded during three different seismic ground motions were investigated. The buildings’ response spectral densities and …