Materials Science and Engineering Commons^™

The Possibilities Of Using Loess Clay Of Kattabog Deposit In The Production Of Ceramic Products, Ruzibaev Bahrom, Saloxidinova Salima

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the research was to determine the properties of loess clay in Kattabog deposit (Uzbekistan) to identify possible areas of use. Modern methods of physicochemical analysis are used: spectroscopic, x-ray phase, electron microscopic methods of analysis. The research results showed that the main phases of clay are hydromica, quartz, kaolinite, calcite and orthoclase. Based on the research, it can be stated that the clay of Kattabog deposit has good physical and technical properties and mineralogical composition, which is a valuable raw material for the production of various ceramics, bricks, tiles, majolica and other products.

Influence Of The Aluminum Oxide Additive On The Phase Composition Of Mullit-Forming Aluminosilicate Minerals, Mkrtchyan Ripsime, Aripova Mastura

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the research is to determine the effect of alumina on the phase composition of shale of the Jerdanak deposit and the quartz-pyrophyllite rock of the Baynaksay deposit during high-temperature firing. X-ray phase analysis determined changes in the phase composition of rocks with additives from 5 to 20% aluminum oxide as a result of firing at 1300 and 1400 °C. A comparative analysis revealed the absence of cristobalite formation, a decrease in the quartz content, and an increase in the amount of mullite for shale samples. No positive effect of alumina additives on the phase composition of quartz-pyrophyllite …

Coordination Compounds Of Copper, Cobalt And Nickel Formates With Formamide And Carbamide, Jumaniyazova Mukaddas, Azizov Tohir

CHEMISTRY AND CHEMICAL ENGINEERING

The synthesis of mixed ligand coordination compounds of copper, cobalt and nickel formates with formamide and urea in an aqueous solution was carried out. The metal content in the complexes was determined by complexometric titration. Using IR spectroscopy, it was proved that the coordination of formamide and urea with the complexing atom is carried out through the oxygen atom of the carbonyl group. The absorption spectrum of coordinated water is also present in the IR spectrum. The nature of the change in the frequency of stretching vibrations of the –OH group in the composition of water indicates its location in …

Configuration And Competitive Reactivity Of Ligands In Mixed Ligand Complexes Of Dialkylditiophosphates And Aminobenbenzimidazole (Part I: Au, Pt, Ag), Esbergenova Botakoz, Daminova Shakhlo, Kadirova Zuhra, Sharipov Khasan

CHEMISTRY AND CHEMICAL ENGINEERING

With the aim of determination of electronic and geometrical structures of mixed-ligand complexes, theoretical modeling of the structures of coordination compounds of transition metals with dialkyldithiophosphate chelating ligands with aminobenzimidazoles carried out using quantum chemical methods. Using BIOVIA Materials Accelrys Studio 2017 software packages, the geometry, electron density distribution, and frontier orbitals calculated for the mixed ligand complexes of Au(III), Pt(II), Ag(I), Cu(II), Ni(II), Fe(III), which are necessary for understanding the electronic structure of coordination compounds with chelating ligands.

Educational Cluster - Foundation Of The National Economy And Regional Innovation System, Usmonov Botir, Kushiev Khabibjon

CHEMISTRY AND CHEMICAL ENGINEERING

The paper analyzes the available resources for the creation of a cluster approach to the integration of education, science and industry in order to create a mechanism to bring the development of the economy to the level of modern requirements. The article describes the collaboration of science, education and industry through the clustering process. Ways to introduce clustering in the national innovation system are described. At the same time, the role of the integration of education, science and industry with the elements of the National Innovation System is analyzed. In conclusion, the role of the education cluster in the regional …

Obtaining Microcrystalline Cellulose From Melon Crops And Studying Its Structure, Umarova Vasila, Mardonov Asror, Khamdamova Dilnoza, Akmalova Guzal

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the study was to obtain microcrystalline cellulose from gourds. Cellulose was isolated from the stems of watermelon and pumpkin by acid and alkaline heat treatment. Microcrystalline cellulose was obtained from cellulose by hydrolysis. Cellulose was hydrolyzed in a mixture of sulfuric acid and hydrogen peroxide. The optical parameters of the microcrystalline cellulose sample, ash content, bulk density, water swelling, and moisture sorption were determined. The structural features of the obtained microcrystalline cellulose were studied by IR spectroscopy. The functional groups present under various conditions for the production of microcrystalline cellulose were determined. The influence of the duration …

Radiopaque Activity Of Iodine Containing Methylene-Bis-Carbamate, Baltabaev Ubaydulla, Djuraev Abdukahhor, Abduvakilov Jahongir, Abdullaeva Matluba

CHEMISTRY AND CHEMICAL ENGINEERING

Considering that many derivatives of bis carbamates have different biological activity, it was intuitive to produce a targeted synthesis of new derivatives of bis carbamates by the interaction of hexamethylene diisocyanate with 3,5-diode-4-hydroxybenzoic acid and 2,4,6-triiodophenol (1: 2 mol, respectively) in freshly distilled dry pyridine at 95-110 оC for 6 hours, the corresponding derivatives were obtained - methylene bis carbamates. Experimental studies have been conducted to identify the acute toxicity and radiopaque properties of the synthesized new N, -hexamethylene bis (2,6-diode-4-carboxyphenylcarbamate).

Modification Of Lithium Lubricants, Azimova Shodiyakhon, Arslanov Sharafutdin, Aripdjanov Oybek, Azimov Dilmurod

CHEMISTRY AND CHEMICAL ENGINEERING

The aim is to study the effect of the presence of free alkalis and acids on the properties of the complex lithium greases and the choice of the optimal dispersion medium, which provides the required physicochemical characteristics of the developed grease. The dispersed phase of lithium greases studied in the polyalphaolefin oils media. It was found that the use of a mixture of polyalphaolefin oil-4 and polyalphaolefin oil-40 as a percentage of 23/77 with a total content of 83.0% provides a relatively low effective viscosity of the lubricant at low temperatures and a relatively high tensile strength at high temperature.

Effective Oil Extraction From Bombyx Mori Silkworm Pupae And Its Structural Characteristics, Avazova Oynavod, Yugai Sveta, Rashidova Sayora

CHEMISTRY AND CHEMICAL ENGINEERING

The conditions for the effective isolation of oil from the silkworm Bombyx mori pupae, based on the extraction of extracted oil with organic reagents, have been studied. The quantitative content of oil was determined in the samples. It is revealed that the oils extracted using gasoline have a high fat-wax composition compared with ethyl alcohol and hexane. When dried pupae processed with gasoline, it is possible to extract up to 16% of fatty substances as much as possible. Physical-chemical characteristics of the oil from silkworm pupae are characterized by high quality indicators. In particular, the presence of unsaturated fatty acids …

Composition Of Liquid Paraffins For Flotation Enrichment Of Potassium Chloride, Vaqqosov Sobir, Xolmuratov Shamsitdin, Buxarov Shuhrat, Kodirov Orifjon

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of this work is to determine the source of liquid paraffins from secondary products of the local chemical industry, compare the performance properties and use the resulting products as apolar co-reagents in silvinite flotation. The experiments were conducted with secondary used hexane and pyrocondensation. To improve the efficiency of flotation, the dependences of the order of reagent’s supply into the process and the time of action were studied. Experiments have shown that when adding tetradecane and pentadecane in an amount of 2.5 to 7.5% to hexane liquid paraffins, it is possible to reduce the tail of KCl to …

Influence Of Technological Parameters On The Chemical Composition Of Calcium Polyphosphates From Phosphorites Central Kyzylkum, Ulugberdieva Ziyada, Khujamberdiev Sherzod, Mirzakulov Kholtura, Usmanov Ilkham

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the research was to study the effect of temperature, the ratio of P2O5EPA:P2O5PRM and the duration of calcination on the content of various forms of P2O5 in calcium polyphosphate. The effect of calcination temperature from 150 to 300 °C, the ratio of P2O5EPA:P2O5FRM from 2,15 to 4,50 and the duration of the process from 20 to 120 minutes on the changes in various forms of P2O5 were studied. It was shown that with increasing temperature to 200-250 °C the content of the total (ortho + poly) assimilable form of Р2О5 increases and then decreases, passing through a …

Bases Of Development Of Technologies Of Synthesis Of Oxide Materials In Big Solar Furnace (Parkent), Gulamova Dilbara, Baxronov Khayot, Bobokhulov Sirojiddin, Eshonkulov Elyor

CHEMISTRY AND CHEMICAL ENGINEERING

The advantages of synthesis of complex oxide compounds by solar energy, the possibility of obtaining highly textured nano materials are shown. The development of heliomaterial science, aimed at the synthesis of new materials, is inextricably linked with the use of effective optical energy systems. On the example of obtaining superconducting materials of nominal composition Bi1.7Pb0.3Sr2Ca(n-1)CunOy (n = 3-20), optimization of the parameters of the optical-energy system of the Big Solar Furnace (Parkent) is shown. The ideology of developing heliotechnology for the synthesis of inorganic materials in a solar furnace is presented. The properties of a superconducting material of nominal Bi1.7Pb0.3Sr2Ca(n1)CunOy …

Framing Energy And Minerals For Future Pathways, Michelle Michot Foss, Michael S. Moats, Kwame Awuah-Offei

Materials Science and Engineering Faculty Research & Creative Works

We present a challenge for Group of Twenty (G20) discussions that entails (1) greater awareness of the role of non-fuel minerals in the global economy overall, but specifically in the energy sector; and (2) the introduction and acceleration of alternative energy sources and technologies. We focus on chemical battery energy storage, given its prominence in all views and outlooks of energy futures, especially for mobility. We present recommendations for G20 discussions and actions on battery materials, and the crucial underlying supply chains for mineral commodities.

Dynamic Analysis Of Viscoelastic Circular Diaphragm Of A Mems Capacitive Pressure Sensor Using Modified Differential Transformation Method, Dr Olurotimi A. Adeleye, Muritala Yusuf, Oluwaseyi .. Balogun

Karbala International Journal of Modern Science

In this paper, a dynamic analysis of the viscoelastic circular diaphragm of a Micro-Electro-Mechanical System (MEMS) capacitive pressure sensor using the Modified Differential Transformation Method (MDTM) is presented. The MEMS technology has been increasingly used to fabricate sensors and actuators and the MEMS capacitive pressure sensor is emerging in many high-performance applications. The deflection of these sensors diaphragm (plate) depends largely on the material of the diaphragm. In this study, a circular diaphragm of viscoelastic material is modeled using the classical plate theory. The governing differential equation is solved using Modified Differential Transformation Method (MDTM) and the result is validated …

Manual For Thin Asphalt Overlays, Lerose Lane, R. Gary Hicks, Dingxin Cheng, Erik Updyke

Mineta Transportation Institute

This manual presents best practices on project selection, mix design, and construction to ensure a superior product when constructing thin asphalt overlays. Experience shows these treatments provide excellent performance when placed on pavements in fair to good condition using proper construction techniques. Though sometime referred to by other names, thin asphalt overlays have been widely used for pavement preservation throughout the world for over 50 years.

Limited infrastructure funding at the local, state, and federal levels has resulted in greater emphasis on the use of pavement preservation techniques to extend pavement life and reduce maintenance costs. Thin asphalt overlays are …

Particle Tracking Of A Simulated Melt Pool Of Selective Laser Melting, Prakash Gautam

Graduate Theses & Non-Theses

Metal additive manufacturing (AM) produces parts by addition as compared to subtraction of material. Selective laser melting (SLM) is an AM technique that prints objects layer-by-layer, selectively melting powders using a laser. The mechanical properties of SLM parts are affected by processing parameters and powder characteristics, both of which alter the molten melt pool flow field. Marangoni convection (M-flow) is a thermo-capillary mass transfer from a region of lower surface tension to a region of higher surface tension, referred to as a radially outward flow for SLM. However, in the presence of surface-active elements such as oxides and sulfides, the …

Effect Of Global Energy Density On Dynamic Strain Hardening Of Selective Laser Melted Alsi10mg, Md Salah Uddin

Graduate Theses & Non-Theses

The characteristics of strain hardening of selective laser melting (SLM) processed AlSi10Mg under dynamic impact was investigated. The dynamic impact at high strain rate loading conditions occurs in many engineering applications, such as collisions of flying objects on aircraft engine components like bird impact, vehicle collisions, and impacts occur in sports events like club impact on golf balls and helmet impact. Among these various applications, the strength of the materials needs to characterize accurately for product quality, performance, and reliability.

AlSi10Mg is a lightweight metal alloy, and it has a growing demand in aircraft, military, and automotive applications. SLM is …

Open Source Arc Analyzer: Multi-Sensor Monitoring Of Wire Arc Additive Manufacturing, Adam M. Pringle, Shane Oberloier, Aliaksei Petsiuk, Paul G. Sanders, Joshua M. Pearce

Michigan Tech Publications, Part 1

Low-cost high-resolution metal 3-D printing remains elusive for the scientific community. Low-cost gas metal arc wire (GMAW)-based 3-D printing enables wire arc additive manufacturing (WAAM) for near net shape applications, but has limited resolution due to the complexities of the arcing process. To begin to monitor and thus control these complexities, the initial designs of the open source GMAW 3-D printer have evolved to include current and voltage monitoring. Building on this prior work, in this study, the design, fabrication and use of the open source arc analyzer is described. The arc analyzer is a multi-sensor monitoring system for quantifying …

Mechanical Properties Of Direct Waste Printing Of Polylactic Acid With Universal Pellets Extruder: Comparison To Fused Filament Fabrication On Open-Source Desktop Three-Dimensional Printers, Arthur Alexandre, Fabio A. Cruz Sanchez, Hakim Boudaoud, Mauricio Camargo, Joshua M. Pearce

Michigan Tech Publications, Part 1

Fused filament fabrication (FFF) is the most common and widespread additive manufacturing (AM) technique, but it requires the formation of filament. Fused granular fabrication (FGF), where plastic granules are directly three-dimensional (3D) printed, has become a promising technique for the AM technology. FGF could be a key driver to promote further greening of distributed recycling thanks to the reduced melt solidification steps and elimination of the filament extruder system. However, only large-scale FGF systems have been tested for technical and economic viability of recycling plastic materials. The objective of this work is to evaluate the performance of the FFF and …

On The Recovery And Fatigue Life Extension Of Stainless Steel 316 Metals By Means Of Recovery Heat Treatment, Ali Haghshenas, M. M. Khonsari

Faculty Publications

In this paper, we propose a methodology for enhancing the fatigue life of SS316 by performing intermittent recovery heat-treatment (RHT) in the Argon environment at different temperatures. To this end, fully-reversed fatigue bending tests are conducted on the heat-treated SS316 specimens. Damping values are obtained using the impact excitation technique to assess the damage remaining in the material after each RHT and the corresponding fatigue life. Damping is also used to distinguish the three stages of the fatigue phenomenon and the onset of crack initiation. The results show that by performing intermittent RHTs, the density of dislocation is decreased substantially …