Materials Science and Engineering Commons^™

Investigating The Impact Of Secondary Activation Time On The Adsorption Properties Of Activated Biochar For Arsenic Removal From Wastewater, Achyuth Bharadwaj Rayarao

Graduate Theses and Dissertations (2019 - present)

Biochar, a naturally occurring and renewable carbon material, becomes porous through activation. Activated biochar is an ideal candidate for use as an adsorbent. The objective of this study is to investigate whether activated biochar derived from Colorado soft pine serves as a better adsorbent and demonstrates enhanced adsorption capabilities after undergoing secondary physical activation at various activation times. The effect of secondary action time on physical adsorption properties drawn from the analysis of isotherm plots, surface areas and pore size patterns were examined by using a physisorption analyzer. Chemical structures were identified using both ultimate and proximate analyses, while porosity …

Study Of The Influence Of B2o3 Oxide On The Physical And Technical Properties Of Ground Enamel Obtained Based On Local Raw Material Components, Shoxrux B. Naimov, Mastura Kh. Aripova

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of the study was to obtain ground enamel based on local raw materials and to study the effect of boron oxide. The selection of local raw materials for producing ground enamel showed that the resulting glass compositions are in the SiO₂–Al₂O₃–Na₂O–K₂O–CaO–B₂O₃ system. To adjust the properties, additives of nickel oxide and cobalt oxide were used. The properties of the developed compositions of primer enamels meet the requirements of GOST 24405-80. It has been determined that the addition of boron and an increase in its amount …

Formation Of Luminescent Coatings With The Use Of Low Melting Glass, Eygeniy N. Poddenezhny, Ekaterina E. Trusova, Andrei A. Boiko, Ekaterina R. Kravcova, Olga V. Davydova

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the present research is to develop compounds and technologies for applying the luminous vitrocrystalline compounds to smooth and ribbed glass substrates in LED lamp structure with a remote photoconverter that contains oxide low melting glass as the base and nanostructured cerium–doped yttrium–aluminum garnet powder as the luminophore. The luminescent coatings based on nanostructured cerium doped yttrium-aluminum garnet powder and low melting glass of composition BaO-Bi₂O₃-B₂O₃-K₂O-SiO₂ where prepared. YAG:Ce³⁺ powder was synthesized by the method of thermochemical reaction. Silica glass powder was introduced into the composition …

Anomalous Of Resistance And Magnetic Susceptibility At 280-310 K And Ambient Pressure In Bismuth Cuprates Synthesized By Solar Energy, Dilbara Dj. Gulamova, Elyor B. Eshonkulov, Valeriya R. Li, Grigor I. Mamniashvili, Timur I. Gulamov

CHEMISTRY AND CHEMICAL ENGINEERING

In order to obtain the full content of high-temperature superconducting phases using the “Super Fast Alloys Quenching” technology in the Large Solar Furnace (Parkent), precursors of bismuth cuprates of the series Bi_1,7Pb_0,3Sr₂Ca_(n-1)Cu_nO_y, n=3-30 were synthesized. Methods for study the properties of precursors are presented. The oriented nano-sized microstructure and layered structure of nanocrystalline nuclei are shown. The phase composition of the precursors at the beginning of the series (n=3-5) is represented by X-ray amorphous and crystalline phases. An increase in the content of CaO and CuO destabilizes the …

Waste Utilization In Korean Cement Plants, Geun-Seong Lee, Zebo Abdullaevna Babakhanova, Mastura Khikmatovna Aripova

CHEMISTRY AND CHEMICAL ENGINEERING

The kiln process in cement plant has the advantage of completely and effectively destroying and burning all organic substances due to high temperature and long residence time, oxygen atmosphere and excellent mixing effect, alkaline conditions of raw materials, and incorporation of trace metals into clinker, and plays a role as a pollutant emission barrier during waste utilization. Waste utilization technology is now proven and successful in cement plants. The waste utilization in Korean cement plants are greatly expanding in the view of energy and material recoveries, and economics as well as environmental preservation. Research on waste utilization in the Korean …

High Temperature Validation Of A Line Heat Source Technique For In-Pile Thermal Conductivity Determination, Katelyn Wada, Allyssa Bateman, Tony Valayil Varghese, Austin Fleming, Brian J. Jaques, David Estrada

Materials Science and Engineering Faculty Publications and Presentations

In-pile instrumentation is critical for advancing operations and materials discovery in the nuclear industry. Ensuring optimal performance of sensors in high temperatures is the first step in demonstrating their viability in the harsh in-pile environment. This work demonstrates the high temperature capabilities of a line heat source and measurement technique previously shown to extract thermal conductivity of nuclear fuel sized samples within a laboratory environment at room temperature. This method uses a hybrid AC/DC measurement technique to obtain rapid measurements of the temperature dependent voltage change of a heater wire, which also acts as a resistance thermometer. Once the temperature …

A Comprehensive Investigation Of The Influence Of Geometric Structure On The Shape Memory Performance Of Nafion, Jade Thomas

Physics Undergraduate Honors Theses

While perfluorosulfonic acid (PFSA) membranes have primarily been used in fuel cells due to their chemical, thermal, and mechanical stability, one PFSA, Nafion, boasts two unique characteristics: a broad glass transition (~55 °C to 130 °C) and a temperature-persistent electrostatic network. The combination of these two characteristics endows Nafion with exceptional shape memory properties – the ability of a material to morph and transform into pre-programmed shapes when exposed to an external stimulus – with enhanced permanent shape memorization, and a potentially near-infinite number of temporary shape memorization. This study focused on expanding the base of knowledge surrounding Nafion’s shape …

The Analysis Of Mechanical Exfoliation Of Graphene For Various Fabrication And Automation Techniques, Lance Yarbrough

Physics Undergraduate Honors Theses

Mechanical Exfoliation

Micro-Mechanical Characterization Of Uhpc Stiffness Mechanisms: Towards A Better Understanding Of Concrete Elastic Modulus, Charissa N. Puttbach

Graduate Theses and Dissertations

Current design code equations for estimating the elastic modulus of specialty concretes like ultra-high performance concrete are not all suitable. Developing empirical curves from exhaustive experimental testing is challenging for concretes that may have high levels of cement replacement with mineral admixtures and fibers at varying volume contents. As such, an alternative approach is taken that seeks to understand the constituent microscale stiffness mechanisms and relate the results to the macroscale. Micropillars are fabricated on several cement paste phases using a focused ion beam. A modified pico-indenter is used to determine the linear and non-linear behavior under micro-compression loading. Micropillar …

A Comprehensive Investigation Of The Influence Of Geometric Structure On The Shape Memory Performance Of Nafion, Jade Thomas

Mechanical Engineering Undergraduate Honors Theses

While perfluorosulfonic acid (PFSA) membranes have primarily been used in fuel cells due to their chemical, thermal, and mechanical stability, one PFSA, Nafion, boasts two unique characteristics: a broad glass transition (~55 °C to 130 °C) and a temperature-persistent electrostatic network. The combination of these two characteristics endows Nafion with exceptional shape memory properties – the ability of a material to morph and transform into pre-programmed shapes when exposed to an external stimulus – with enhanced permanent shape memorization, and a potentially near-infinite number of temporary shape memorization. This study focused on expanding the base of knowledge surrounding Nafion’s shape …

Release Of Small Molecules From Rubber: Effects Of Materials Properties, Mechanical Loading And Molecular Interactions, Yongcan Du

All Dissertations

Release of small molecules from polymeric materials has wide applications in the delivery systems of active molecules such as drug, fragrance, and semiochemical. Rubber materials are good candidates for the excipients of those systems due to properties such as good flexibility, permeability, and biocompatibility. Factors like material properties, mechanical loading, and molecular interactions may affect the release of small molecules in those systems. Therefore, understanding how those factors affect the release is key to the formulation, design, and evaluation of those systems.

To study the effects of materials properties, vulcanized natural rubber sheets with different crosslink densities, loaded with small …

Free And Forced Vibrations Of Elastically Restrained Cantilever With Lumped Oscillator, Alireza Babaei, Johné Parker, Paria Moshaver

Earth and Environmental Sciences Faculty Publications

The efficiency assessment of cantilever-based energy harvesters relies on vibrational analysis, which necessitates modi- fications aimed at enhancing efficiency. These modifications involve manipulating the fundamental frequency to lower values and encompassing a wider range of resonances within a specified bandwidth. Consequently, this paper introduces an original analytical-numerical exploration into the vibratory response of a cantilever with a novel boundary condi- tion involving an elastically restrained oscillator-spring arrangement. At the microbeam’s tip, an oscillator is elastically confined by a linear spring, resulting in a novel set of coupled governing equations and a distinct shearing boundary condition. Microbeam equations is derived from …

A Comprehensive Materials Approach To Thermal Management In Fiber Lasers, Bailey Meehan

All Dissertations

Optical fiber-based amplifiers and lasers enable a great many useful devices and conveniences. Unfortunately, however, they can generate considerable heat during operation that drives the need for complex cooling solutions, thus reducing many of the size, weight, and power (SWAP) benefits for which fiber lasers are known. Additionally, at elevated temperatures, thermally-driven phenomena, such as Transverse Mode Instability (TMI), can be induced that limit the power-scaling of fiber lasers. The focus of this Dissertation is to explore novel approaches to thermal management in fiber lasers through judicious materials science and engineering to obviate the aforementioned limitations. Fibers studied in this …

Quasi-Static And Dynamic Deformation Of Aluminum Matrix Composites Reinforced By Core-Shell Al35ti15cu10mn20cr20 High-Entropy Alloy Particulates, Dezhi Zhu, Tingting Chen, Xiaoqiang Jin, Haiming Wen, Zhiqiang Fu, Shengguan Qu

Materials Science and Engineering Faculty Research & Creative Works

Core-Shell Structured Particles Are Potential Reinforcement Agents For Metal Matrix Composites. In This Work, Aluminum Matrix Composites Reinforced With Core-Shell Structured Al35Ti15Cu10Mn20Cr20 High-Entropy Alloy (HEA) Particles Were Fabricated By Spark Plasma Sintering (SPS) And High-Temperature Diffusion Post-Treatment. Dynamic Compression Behavior And Adiabatic Shear Failure Mechanism In The Composites Were Investigated By Split Hopkinson Pressure Bar (SHPB), Scanning Electron Microscopy And Transmission Electron Microscopy. Results Showed That The Shell Thickness Of The Core-Shell Particles Ranged From 0.4 To 1.6 Μm, Which Were Formed By Thermal Diffusion Between HEA Core And Aluminum Alloy. The 30 Vol% (Al35Ti15Cu10Mn20Cr20)p/2024Al Composite Showed A High Compressive …

Encapsulated 2d Materials And The Potential For 1d Electrical Contacts, Sarah Wittenburg

Physics Undergraduate Honors Theses

The utilization of two-dimensional materials and heterostructures, particularly graphene and hexagonal boron nitride, have garnered significant attention in the realm of nanoelectronics due to their unique properties and versatile functionalities. This study focuses on the synthesis and fabrication processes of monolayer graphene encapsulated between layers of hBN, aiming to explore the potential of these heterostructures for various electronic applications. The encapsulation of graphene within hBN layers not only enhances device performance but also shields graphene from environmental contaminants, ensuring long-term stability. Experimental techniques, including mechanical exfoliation and stamp-assisted transfer, are employed to construct three-layer stacks comprising hBN-graphene-hBN. The fabrication process …

Characterization Of Platinum On Carbon Nanoparticles Selectively Coated With Titanium Nitride (Tin), Matthew Maramo

Honors Scholar Theses

Proton exchange membrane fuel cells are a promising low-carbon technology that still face problems including low durability during their normal operation cycles. At the cathode, the carbon supports of the catalysts may corrode. Atomic layer deposition of titanium nitride is performed on prepared catalyst layer samples. The purpose of the deposition is to create a thin film over the carbon supports to reduce carbon support corrosion and improve the lifespan of the fuel cell. Sheet resistances and contact angles are measured for the samples before and after the deposition, although some samples did not receive the deposition and post-deposition characterization …

Dynamic Impact Testing And Numerical Analysis Of Non-Proprietary Astm F2656-20 M50 Anti-Ram Barrier Components, Weston Kelley

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In a post-9/11 world, hostile actors are using vehicles as weapons to inflict civilian casualties. Pedestrians, vulnerable road users, military personnel, and police may be targeted using a vehicle as a weapon. The United States Department of Defense (DoD) also utilizes Entry Control Facilities (ECFs) which are carefully designed transportation corridors to manage how threat vehicles are able to access military facilities. In 2004, DoD started to upgrade all ECFs using both passive and active barriers. Many anti-ram vehicle barriers were evaluated according to the criteria established in ASTM F2656, but to date few options are available which are (1) …

Investigation Of Domain Formation During Phase Separation In A Mixture Of Flexible And Rigid Biopolymers, Steven Huntley

All Theses

Complex fluids and heterogenous mixtures composed of multiple types of polymers are found throughout industrial and biological fluid systems. For example, extrusion based additive manufacturing systems pass dense mixtures of polymers through the extrusion heads to deposit composite polymeric materials. In cells, active and complex mixtures of biopolymers self-organize into assemblies that perform critical physiological functions.

Polymers in dense solutions undergo phase separation as a result of differences in physiochemical properties. A few examples of these properties include charge, structure, rigidity, and hydrophobicity. We observe the formation of polymer domains composed of rigid and a flexible biopolymer species that phase …

Improved Ballistic Impact Resistance Of Nanofibrillar Cellulose Films With Discontinuous Fibrous Bouligand Architecture, Colby Caviness

All Theses

Natural protective materials offer unparalleled solutions for impact-resistant material designs that are simultaneously lightweight, strong, and tough. Particularly, the dactyl club of mantis shrimp features chitin nanofibrils organized in a Bouligand structure, which has been shown to effectively dissipate high-impact energy during powerful strikes. The mollusk shells also achieve excellent mechanical strength, toughness, and impact resistance with a staggered, layer-by-layer structure. Previous studies have shown that hybrid designs, by combining different bioinspired microstructures, can lead to enhanced mechanical strength and energy dissipation capabilities. Nevertheless, it remains unknown whether combining Bouligand and staggered structures in nanofibrillar cellulose (NFC) films, forming a …

The Analysis Of Mechanical Exfoliation Of Graphene For Various Fabrication And Automation Techniques, Lance Yarbrough

Mechanical Engineering Undergraduate Honors Theses

Mechanical Exfoliation of Graphene is an often-overlooked portion of the fabrication of quantum devices, and to create more devices quickly, optimizing this process to generate better flakes is critical. In addition, it would be valuable to simulate test pulls quickly, to gain insight on flake quality of various materials and exfoliation conditions. Physical pulls of graphene at various temperatures, pull forces, and pull repetitions were analyzed and compared to the results of ANSYS simulations, solved for similar results. Using ANSYS’ ability to predict trends in exfoliations, flake thickness and coverage using stress and deflection analyses were investigated. Generally, both strongly …