Other Materials Science and Engineering Commons^™

Novel And Fast Peridynamic Models For Material Degradation And Failure, Siavash Jafarzadeh

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Fracture is one of the main mechanisms of structural failure. Corroded surfaces with chemically-induced damage are, notably, potential sites for crack initiation and propagation in metals, which can lead to catastrophic failure of structures. Despite some progress in simulating fracture and damage using classical models, realistic prediction of complex damage progression and failure has been out of reach for many decades. Peridynamics (PD), a nonlocal theory introduced in 2000, opened up new avenues in modeling material degradation and failure. Existing numerical methods used to discretize PD equations, however, are quite expensive as the PD nonlocal interactions make them unaffordable for …

Life Cycle Assessment Of An Ifixit Pro Tech Toolkit, Camden N. Webb, Dylan A. Ell

Materials Engineering

A life cycle assessment of an iFixit Pro Tech Toolkit was performed to determine the environmental impacts of iFixit’s best-selling toolkit. SimaPro software was used to measure three impact categories: energy usage, water consumption, and global warming potential. This project provides quantitative data on the resources required for repairing devices through use of the toolkit to ultimately reduce the global e-waste stream by re-using electronics. Using the cut-off method, global warming potential of the kit was 4.1 kg of CO₂ equivalents, water consumption was 1.5 m³, and energy usage was 73.9 MJ. Major contributors to these impact …

Dental Cement Thickening Agents For Mudslide Prevention, Kristina Emiliya Babayev, Emily Elizabeth Johnson, Diana Evet Reihaneh

Materials Engineering

The purpose of this project is to develop a non-toxic mud thickening agent for the application of decreasing mudslide intensity where performance is measured by flow rate, viscosity, and toxicity tests. We hypothesized that dental cements could be a potential candidate due to their adhesive, hydrophilic, and biocompatible properties. Zinc phosphate, glass ionomer, and polycarboxylate cement were among the dental cements tested. These tests were performed at low and high concentrations of 25 grams and 125 grams, respectively, mixed into soil to produce 3500 gram samples. The dental cements produced noticeable thickening effects in the mud, as the average viscosity …

Effect Of Dissolved Oxygen On Corrosion Of Carbon And 13cr Steel In A Brine Environment, Kevin Peter Iu, Andy Zhou

Materials Engineering

Oxygen corrosion is a major threat to seawater injection systems that are part of offshore drilling operations. Seawater is typically deoxygenated to an industry standard of(DO) by injection through a deaeration column followed by treatment with oxygen scavenging chemicals. Commercial simulation software like OLI Studio: Corrosion Analyzer predicts high corrosion rates when injection seawater contains high DO levels, justifying deoxygenation. However, a notable lack of experimental data exists concerning the effect of varying levels of dissolved oxygen on corrosion rate. The goal of this project is to measure the effect of three dissolved oxygen levels (0, 62, and 620 ppb) …

Pressure Driven Desalination Membranes: Lyotropic Liquid Crystals Containing Single Walled Carbon, Matteo A. Del Giudice, Samantha Castillo Merigold

Materials Engineering

This project presents a potential alternative desalination technique that utilizes the ion rejection properties of single walled carbon nanotubes dispersed in a lyotropic liquid crystal (LLC) matrix. Previous research has pointed to the polymerizable surfactant methacryloxy ethyl hexadecyl dimethyl ammonium bromide (C16MA) having capabilities of filtering molecular components smaller than a nanometer, when oriented in cylindrical micelles. SWCNTs were dispersed in deionized water by probe sonication and addition of surfactant cetyltrimethylammonium bromide (CTAB) due to SWCNTs’ hydrophobic properties. Membranes were produced containing 55wt% C16MA, 37wt% DI water, 0.1wt% with respect to the monomer (WRM) SWCNTs, 1.9 wt% WRM 2,2-dimethoxy-2-phenylacetophenone (photointiator), …

Sound, Material And Strength Correlation, Ryan Mcbride

Symposium of Student Scholars

With a growing amount of manufacturing utilizing 3D printing, there is a correlation between strength and material which can affect sound produced by sirens. An air raid siren that has been downloaded from Thingiverse.com spins with a 49:1 gear ratio to produce 2 tone sounds and with that large number of revolutions comes friction, and in order to create a 3D printed air raid siren, the siren must be made out of a material that can withstand high temperatures without melting and quick rotations without delaminating. There are many materials that can be printed to withstand those forces, but it …

Computational Design Of Nonlinear Stress-Strain Of Isotropic Materials, Askhad M.Polatov, Akhmat M. Ikramov, Daniyarbek Razmukhamedov

Chemical Technology, Control and Management

The article deals with the problems of numerical modeling of nonlinear physical processes of the stress-strain state of structural elements. An elastoplastic medium of a homogeneous solid material is investigated. The results of computational experiments on the study of the process of physically nonlinear deformation of isotropic elements of three-dimensional structures with a system of one- and double-periodic spherical cavities under uniaxial compression are presented. The influence and mutual influence of stress concentrators in the form of spherical cavities, vertically located two cavities and a horizontally located system of two cavities on the deformation of the structure are investigated. Numerical …

Exploration Of The Sludge Biodiesel Pathway, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Wastewater sludge is an overlooked source of fat, oil, and grease (FOG) that could be converted into biodiesel. The United States produces about 8 million tons of sludge per year. The disposal cost for this amount of sludge is about 2 billion US dollars. The widespread availability and low cost of sludge compared to other biodiesel raw materials make it an economical choice for a renewable fuel. Using sludge as a raw material can produce 25 to 30 mg per gram of fatty acid methyl ester (FAME); the main component of biodiesel. Sludge biodiesel has the potential of transforming a …

Voltage-Controlled Magnetic Anisotropy In Antiferromagnetic Mgo-Capped Mnpt Films, P. H. Chang, Wuzhang Fang, T. Ozaki, Kirill Belashchenko

Kirill Belashchenko Publications

The magnetic anisotropy in MgO-capped MnPt films and its voltage control are studied using first-principles calculations. Sharp variation of the magnetic anisotropy with film thickness, especially in the Pt-terminated film, suggests that it may be widely tuned by adjusting the film thickness. In thick films the linear voltage control coefficient is as large as 1.5 and -0.6 pJ/Vm for Pt-terminated and Mn-terminated interfaces, respectively. The combination of a widely tunable magnetic anisotropy energy and a large voltage-control coefficient suggest that MgO-capped MnPt films can serve as a versatile platform for magnetic memory and antiferromagnonic applications.

Comparison Of Tensile Properties Of Triaxial Braided Carbon Fiber Composites Made From Vacuum Assisted Resin Transfer Molding (Vartm) And Autoclave Molding, Donald A. Klosterman, Charles Browning

Chemical and Materials Engineering Faculty Publications

Triaxially braided fiber composites are increasingly being used in aerospace, ballistic, and sporting good applications due to their inherent damage tolerance, torsional stability, and cost compared to woven fabrics and unidirectional preforms. There have been numerous publications over the past 15-20 years on the mechanical properties and failure mechanisms of triaxial braided composites. However, most of these have involved panels made with autoclave curing. In the present study, braided carbon fiber composites were made using autoclave curing and vacuum assisted resin transfer molding (VARTM). The goal of the study was to compare the physical and tensile properties of quasi-isotropic panels …

Husky Hand: A Low-Cost Electro-Mechanical Prosthetic Arm For The Underprivileged, Adam Robert

Thinking Matters Symposium

A continuation of a low-cost prosthetic upper limb prototype design which was investigated in EGN 301. The prosthetic is specifically designed for the needs and requirements of under privileged individuals in the Dominican Republic with upper limb amputations. The project focuses on the creation of an open-source computer aided prosthetic hand/arm model. The design allows consumer-grade fused filament fabrication (FFF) 3-D printers to be used. The improved design allows for the integration of the PQ-12 linear actuator for grasp and finger control. This simplifies the assembly, while, also reducing the size and mass of the whole unit. Producing a low-cost …

Detection And Aggregation Of Listeria Monocytogenes Using Polyclonal Antibody Gold-Coated Magnetic Nanoshells Surface-Enhanced Raman Spectroscopy Substrates, Robert T. Busch, Farzia Karim, Yvonne Sun, H. Christopher Fry, Yuzi Liu, Chenglong Zhao, Erick S. Vasquez

Chemical and Materials Engineering Faculty Publications

Magnetic nanoshells with tailored surface chemistry can enhance bacterial detection and separation technologies. This work demonstrated a simple technique to detect, capture, and aggregate bacteria with the aid of end-functionalized polyclonal antibody gold-coated magnetic nanoshells (pAb-Lis-AuMNs) as surface-enhanced Raman spectroscopy (SERS) probes. Listeria monocytogenes were used as the pathogenic bacteria and the pAb-Lis-AuMNs, 300 nm diameter, were used as probes allowing facile magnetic separation and aggregation. An optimized covalent bioconjugation procedure between the magnetic nanoshells and the polyclonal antibody was performed at pH six via a carbodiimide crosslinking reaction. Spectroscopic and morphological characterization techniques confirmed the fabrication of stable pAb-Lis-AuMNs. …

Solid State Synthesis And Characterization Of Apatite Based Ceramic Waste Form For The Immobilization Of Radioactive Iodine, Md Imdadul Islam

LSU Doctoral Dissertations

The growing demand for nuclear power in the United States and worldwide is accountable for addressing the major concern of radioactive waste, involving the technical challenges of maintaining the nuclear fuel cycle and immobilizing high-level wastes for safe disposal in geological storage. The appropriate selection of waste forms for spent nuclear fuel such as fission products and radionuclides can be effective means for a feasible and sustainable nuclear fuel cycle. But highly volatile radionuclides such as iodine (129) are of specific concern due to its extraordinary long half-life (15.7 million years). Due to its poor solubility and high volatility at …

Fabrication And Characterization Of Electrospun Poly(Acrylonitrile-Co-Methyl Acrylate)/Lignin Nanofibers: Effects Of Lignin Type And Total Polymer Concentration, Suchitha Devadas, Saja M. Nabat Al-Ajrash, Donald A. Klosterman, Kenya A. Crosson, Garry S. Crosson, Erick S. Vasquez

Chemical and Materials Engineering Faculty Publications

Lignin macromolecules are potential precursor materials for producing electrospun nanofibers for composite applications. However, little is known about the effect of lignin type and blend ratios with synthetic polymers. This study analyzed blends of poly(acrylonitrile-co-methyl acrylate) (PAN-MA) with two types of commercially available lignin, low sulfonate (LSL) and alkali, kraft lignin (AL), in DMF solvent. The electrospinning and polymer blend solution conditions were optimized to produce thermally stable, smooth lignin-based nanofibers with total polymer content of up to 20 wt % in solution and a 50/50 blend weight ratio. Microscopy studies revealed that AL blends possess good solubility, miscibility, and …

Magnetically Induced Demulsification Of Water And Castor Oil Dispersions Stabilized By Fe3o4-Coated Cellulose Nanocrystals, Mohammad J. Hasan, Frankie A. Petrie, Ashley E. Johnson, Joshua Peltan, Meredith Gannon, Robert T. Busch, Serhiy O. Leontsev, Erick S. Vasquez, Esteban E. Ureña-Benavides

Chemical and Materials Engineering Faculty Publications

Superparamagnetic iron oxide (Fe3O4) nanoparticle (NP) coated cellulose nanocrystals (CNCs) were synthesized and used to prepare emulsions with magnetically controlled stability. Magnetite NPs were deposited onto the surface of wood pulp CNCs (WCNCs) and bacterial CNCs (BCNCs) by a one-step coprecipitation method. The effect of the CNC to Fe3O4 mass ratio (1:1, 1:2, and 1:4) was varied to optimize the colloidal, magnetic and emulsifying properties of the hybrid NPs. TEM images showed that the 1:4 ratios lead to greater coverage of Fe3O4 than lower Fe3O4 loadings (1:1, and 1:2). The CNCs and Fe3O4 appeared to interact via hydrogen bonding between …

Jcati Carbon Fiber Recycling Shredder, Benjamin Cooley

All Undergraduate Projects

Once carbon fibers are cast into a resin and used in a composite material, retrieving those fibers can be a difficult task. However, it is beneficial to recycle and reuse the fibers from old unneeded components rather than pay the cost of acquiring new ones. The Joint Center for Aerospace Technology Innovation (JCATI) carbon fiber recycling device condenses the multistep process of extracting the fibers by integrating all steps into one automated device. In the previous version of the device, the cutting blades turned the long composite strips into thin fingers but did not sever them across the width.

The …

Observation Of New Particle Formation In The Northern Hemisphere At Altitude From 4 To 20 Km, Mohamed Saad

Electronic Theses and Dissertations

New particle formation (NPF) is investigated using measurements of aerosol size distributions and meteorological variables made in two continents, including USA and Europe. Despite the considerably different aerosol particle abundances among the sites, a common relationship was found between the characteristics of NPF events and the air mass convective and/or advective transport. CO and O3 act as tracers of tropospheric and stratospheric air, respectively, their statistical relationship can be used to quantify air mass characteristics and origins. The mixing ratio values of CO increased within the upper troposphere layer before/during NPF events, which may serve as an indicator of occurring …

Recycling Of Fiber Polymer Matrix Composites In Cementitious Materials, Edward Patton Clark

Electronic Theses and Dissertations

Recycling options for fiber polymer matrix composite waste materials are limited because they typically cannot be reused, reprocessed for down-cycling, and are generally environmentally unfriendly. The utility industry, specifically electrical distribution, has been increasingly using hybrid carbon, glass fiber, and epoxy resin composite rods for high-voltage (HV) conductor transmission lines. The high-voltage conductor core (HVCC) used in the transmission line can have an optimal in-service-life of roughly several decades, in which the material is then retired to a waste landfill. Currently, there is limited research and recycling methodology for these hybrid composite rods. In this research, powder carbon fiber, glass …

Monitoring Of Overhead Polymer Core Composite Conductors Under Excessive Mechanical Loads Using Fiber Bragg Grating Sensors, Daniel H. Waters

Electronic Theses and Dissertations

This combined experimental and numerical study addresses mechanical effects associated with static and dynamic loading of novel High Temperature Low Sag (HTLS) transmission line polymer core composite conductors. The developed methodology was successfully applied to ACCC® to explain the complex failure mechanisms associated with combined bending and tension loading. Furthermore, the use of Fiber Bragg Grating (FBG) sensors was investigated for the first time to monitor the ACCC® design during installation and in-service.

Transverse low-velocity impacts to the ACCC® conductor having either free or constrained end conditions and large axial tensile loads were performed. It was identified that the most …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …