Metallurgy Commons^™

Hydrogen Absorption Induced Slow Crack Growth In Austenitic Stainless Steels For Petrochemical Pressure Vessel Industries, Ronnie Higuchi Rusli

Makara Journal of Technology

Type 304L and type 309 austenitic stainless steels were tested either by exposed to gaseous hydrogen or undergoing polarized cathodic charging. Slow crack growth by straining was observed in type 304L, and the formation of α‘ martensite was indicated to be precursor for such cracking. Gross plastic deformation was observed at the tip of the notch, and a single crack grew slowly from this region in a direction approximately perpendicular to the tensile axis. Martensite formation is not a necessary condition for hydrogen embrittlement in the austenitic phase.

Simulation On The Use Of Losat Data For Rice Field Mapping, Bambang H. Trisasongko, Dyah R. Panuju, Boedi Tjahjono, Baba Barus, Hari Wijayanto, Mahmud A. Raimadoya, Irzaman Irzaman

Makara Journal of Technology

Simulation on the Use of LOSAT Data for Rice Field Mapping. Since the launch of LAPAN-TUBSAT satellite in 2007, Indonesia has been developing mission on earth observation missions for various applications. The next generation mission, called LAPAN-ORARI Satellite (LOSAT), is currently under development and expected to be launched in 2011. In order to facilitate the applications, a thorough assessment of the sensor should be made. This paper presents an examination of simulated LOSAT data for rice monitoring and mapping purposes coupled with QUEST statistical tree. We found that three-band simulated LOSAT data were suitable for the task with reasonably high …

Development Of Technology Parameter Towards Shipbuilding Productivity Predictor Using Cubic Spline Approach, Bagiyo Suwasono, Sjarief Widjaja, Achmad Zubaydi, Zaed Yuliadi, I Nyoman Budiantara

Makara Journal of Technology

Development of Technology Parameter Towards Shipbuilding Productivity Predictor Using Cubic Spline Approach. Ability of production processes associated with state-of-the-art technology, which allows the shipbuilding, is customized with modern equipment. It will give impact to level of productivity and competitiveness. This study proposes a nonparametric regression cubic spline approach with 1 knot, 2 knots, and 3 knots. The application programs Tibco Spotfire S+ showed that a cubic spline with 2 knots (4.25 and 4.50) gave the best result with the value of GCV = 56.21556, and R2 = 94.03%.Estimation result of cubic spline with 2 knots for the PT. Batamec shipyard …

Shaft Torsional Vibration Response Of Vertical Axis Ocean Current Turbine Model Due To Torque Excitation, Adi Wirawan Husodo, I Ketut Aria Pria Utama, I Made Ariana

Makara Journal of Technology

Shaft Torsional Vibration Response of Vertical Axis Ocean Current Turbine Model Due to Torque Excitation. The current research aimed to study the torsional vibration response of Vertical Axis Ocean Current Turbine due to randomly torque excitation pattern, owing to the variety of ocean current velocity. The turbine model is composed of 3 aluminum blades of NACA 0018 connected to steel shaft. Turbine dimensions are 10 cm of chord, 1.8 cm of chamber and 100 cm of span. The variation of ocean current velocity is 0.5 m/s, 1.0 m/s, 1.5 m/s, 2.0 m/s, 2.5 m/s and 3.0 m/s. The Model has …

Dye Sensitized Solar Cell With Conventionally Annealed And Post-Hydrothermally Treated Nanocrystalline Semiconductor Oxide Tio2 Derived From Sol-Gel Process, Akhmad Herman Yuwono, Badrul Munir, Alfian Ferdiansyah, Arif Rahman, Wulandari Handini

Makara Journal of Technology

Dye-sensitized solar cell (DSSC) is one of the very promising alternative renewable energy sources to anticipate the declination in the fossil fuel reserves in the next few decades and to make use of the abundance of intensive sunlight energy in tropical countries like Indonesia. In the present study, TiO2 nanoparticles of different nanocrystallinity was synthesized via sol−gel process with various water to inorganic precursor ratio (Rw) of 0.85, 2.00 and 3.50 upon sol preparation, followed with subsequent drying, conventional annealing and post-hydrothermal treatments. The resulting nanoparticles were integrated into the DSSC prototype and sensitized with an organic dye made of …

An Empirical Model For Build-Up Of Sodium And Calcium Ions In Small Scale Reverse Osmosis, Subriyer Nasir

Makara Journal of Technology

A simple models for predicting build-up of solute on membrane surface were formulated in this paper. The experiments were conducted with secondary effluent, groundwater and simulated feed water in small-scale of RO with capacity of 2000 L/d. Feed water used in the experiments contained varying concentrations of sodium, calcium, combined sodium and calcium. In order to study the effect of sodium and calcium ions on membrane performance, experiments with ground water and secondary effluent wastewater were also performed. Build-up of salts on the membrane surface was calculated by measuring concentrations of sodium and calcium ions in feed water permeate and …

The Effect Of Enzymatic Hydrolysis On The Properties Of Protein Hydrolysate From Paddy Mushroom, Niken Widya Palupi, Wiwik Siti Windrati, Tamtarini Tamtarini

Makara Journal of Technology

Protein hydrolysate was prepared from Paddy (Volvariella volvaceae) mushroom. Hydrolysis uses commercially protease available Protamex ™ with enzyme concentration of 0.1% (w/w). Hydrolysis was performed at three different temperatures (room temperature, 40 °C, and 50 °C) with different incubation periods (60, 90, and 120 minutes). Enzyme inactivation was done in 90 °C for 3 minutes. Yield and degree of hydrolysis ranged from 94.76% to 99.55% and 19.06% to 24.59%. Protein solubility was about 89–11,8%. The longer time of hydrolysis, the darker the color of protein hydrolysate. Protein hydrolysate which has hydrolysis at 50 °C for 120 minutes has the highest …

Effect Of Diafiltration On Preparation Of Fermented Mung Beans Concentrate As Probiotic Savory Flavor Through Ultrafiltration Membrane, Aspiyanto Aspiyanto, Agustine Susilowati

Makara Journal of Technology

Diafiltration by means of the ultrafiltration system of probiotic fermented Mung beans (Phaseolus radiatus L.) concentrate has been performed to reduce or eliminate salts and smaller impurities than the nominal cut-off of the membrane of 20,000 nominal weight cut-off (NWCO). These processes have been conducted as an attempt in order to get a probiotic product with organoleptic acceptability, composition, and the optimal total lactic acid bacteria (LAB) counts because the presence of salts will affect on the viability of LAB and the cell lysis of LAB and limit its utility in food products. Concentrate of probiotic mung beans was prepared …

Remote Sensing And Geographical Information System To Identify Drought Potency, Puguh Dwi Raharjo

Makara Journal of Technology

Remote Sensing and Geographical Information System to Identify Drought Potency. Kebumen regency was drought in year 2008, community clean water shortages and irrigation water following a decline in water resources. The use of remote sensing data and GIS can be used to identify the potential for drought-prone areas. Transformation of Landsat TM satellite imagery to obtain the brightness index, wetness index and vegetation index used to determine surface conditions in relation to drought. Brightness index and wetness index derived from the tasseled cap modifications, while the vegetation index derived from normalized difference vegetation index (NDVI) values. Other parameters such as …

High Pressure Adsorption Isotherm Of Co2 On Activated Carbon Using Volumetric Method, Awaludin Martin, Bambang Suryawan, Muhammad Idrus Alhamid, Nasruddin Nasruddin

Makara Journal of Technology

High Pressure Adsorption Isotherm of CO2 on Activated Carbon using Volumetric Method. Adsorption system is ones of the most effective methods for CO2 separating with other substances that produced from the burning of fossil fuels. In the design for that application, beside of characteristics of porous material (adsorbent) data, CO2 adsorption data on the adsorbent (kinetic and thermodynamic) are also needed. The aim of this research is resulting isothermal adsorption data at pressures up to 3.5 MPa by indirect methods (volumetric method) at isothermal temperature of 300, 308, 318 and 338 K. Adsorbent that used in this research is activated …

Concept Design And Testing Of Multi-Nozzle Water Mist Fire Suppression System, Danardono A. Sumarsono, Yulianto S. Nugroho, Mariance Mariance, I Gede Wahyu W. Ariasa

Makara Journal of Technology

In this work a flexible design of multi-nozzle arrangement of water mist fire suppression system was studied. The source of fire was a 65 mm diameter cooking oil fire. An investigation on the impact of nozzle arrangement on the temperature profile of fires was conducted. The occurance of oil splash due to the application of water mist was also studied. The water mist systems developed in the present work can effectively extinguish cooking oil fires and prevented them from re-ignition. The spray angle, discharge pressure, and water flow rate were important factors to determine the effectiveness of water mist in …

The Stability Characteristics Of Sandbag Submerged Breakwater, Ferry Fatnanta, Widi Agoes Pratikto, Haryo Dwito Armono, Wahyudi Citrosiswoyo

Makara Journal of Technology

The Stability Characteristics of Sandbag Submerged Breakwater. Breakwater is one of coastal structures to overcome problems of abrasion. Due to difficulties in obtaining rock material at the coastal area. The using of sandbags as a breakwater provides advantages in utilizing local materials. A Sandbag has a smooth surface, so the internal shear forces are relatively small. According to these phenomena, the research for parameters that are expected to affect the stability of the sand bags. These parameters are a slope, shape and formation of sand bags. This experimental research conducted in two dimensional physical model and took place on the …

Static Hand Gesture Recognition Of Indonesian Sign Language System Based On Backpropagation Neural Networks, Farida Asriani, Hesti Susilawati

Makara Journal of Technology

Static Hand Gesture Recognition of Indonesian Sign Language System Based on Backpropagation Neural Networks. The main objective of this research is to perform pattern recognition of static hand gesture in Indonesian sign language. Basically, pattern recognition of static hand gesture in the form of image had three phases include: 1) segmentation of the image that will be recognizable form of the hands and face, 2) feature extraction and 3) pattern classification. In this research, we used images data of 15 classes of words static. Segmentation is performed using HSV with a threshold filter based on skin color. Feature extraction performed …

Characterization Of Inconel 718: Using The Gleeble And Varestraint Testing Methods To Determine The Weldability Of Inconel 718, Nathaniel Oscar Knock

Master's Theses

Nickel based superalloys were developed to withstand the severe thermal and mechanical environment associated with rocket propulsion systems and jet engines. In many alloy systems the strength of a component rapidly deteriorates as the operating temperature increases. Nickel based superalloys, however, retain strength over a range of temperatures which includes the operating range for many propulsion systems. This improved performance is accomplished by a combination of solid-solution strengthening, precipitation strengthening and grain-boundary strengthening. Furthermore, super-alloy systems are designed for ease of fabrication, to include machining, welding and heat treating. Inconel 718 was developed to overcome problems with post-weld cracking that …

Effect Of Friction Stir Processing On Microstructure And Tensile Properties Of An Investment Cast Al-7si-0.6mg Alloy, Saumyadeep Jana, Rajiv S. Mishra, John A. Baumann, Glenn J. Grant

Materials Science and Engineering Faculty Research & Creative Works

Friction stir processing (FSP) is emerging as a promising tool for microstructural modification. the current study assesses the effects of FSP on the microstructure and mechanical properties of an investment cast Al-7Si-Mg alloy. FSP eliminates porosity and significantly refines eutectic Si particles. the extent of particle refinement varied with changes in processing conditions. a high tool rotation rate and a low-to-intermediate tool traverse speed generated a higher volume fraction of finer particles. Tensile ductility changed significantly as a result of FSP, whereas ultimate tensile strength improved only marginally. Yield strength was similar in both cast and FSP samples under various …

Analysis Of Microstructural Evolution During Friction Stir Welding Of Ultrahigh-Strength Steel, M. Ghosh, K. Kumar, R. S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

Friction stirs lap-welded advanced high-strength M190 steel exhibited formation of lath martensite at weld nuggets, a ferrite layer at faying surfaces and a ferrite-pearlite microstructure at the bottom of the stir zone. the phase transformation was governed by severe plastic deformation in the austenitic region followed by cooling. the strain rate and peak temperature played key roles in controlling the prior-austenitic grain size and were correlated to the Zener-Hollomon parameter. an empirical relationship has been obtained for dynamically recrystallized austenite grains. © 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

The Effects Of Applied Strain And Heat Treatment On The Properties Of Niti Wire During Shape Setting, Frank Zapoticla

Master's Theses

NiTi components are commonly subjected to thermo-mechanical heat treatments during production and fabrication. This study investigates the effects of applied strain of 0-10% and heat treatments of 300-600ºC for times of 2-30 minutes during shape-setting of Ti–50.8 at% Ni wire with a nominal diameter of 0.495 mm and an initial transition temperature, Af, of 12ºC. Strain was applied prior to heat treatments by coiling NiTi wire, essentially producing coiled springs, around different diameter steel mandrels to obtain different strain levels. The samples of NiTi wire under applied strain were heat treated in a salt bath, followed by a rapid quench. …

Structural And Magnetic Properties Of Neodymium–Iron–Boron Clusters, Jeremy J. Anderson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Using inert gas condensation techniques the properties of sputtered neodymium-iron-born clusters were investigated. A D.C. magnetron sputtering source created vaporous Nd-Fe-B which was then condensed into clusters and deposited onto silicon substrates. A composite target of Nd-Fe-B discs on an iron plate and a composite target of Nd-(Fe-Co)-B were utilized to create clusters. The clusters were coated with a carbon layer through R.F. sputtering to prevent oxidation.

Samples were investigated in the TEM and showed a size distribution with an average particle diameter of 8.11 nm. The clusters, upon deposition, were amorphous as indicated by diffuse diffraction patterns obtained through …

The Effects Of Carbon, Boron And Vanadium On The Microstructural Evolution And Hardness Of Steel-Based Hardfacing Alloys, Kyle Rafa

Materials Engineering

Current hardfacing alloys provide insufficient wear resistance due to either cracking or significant material wear. To increase wear resistance of steel-based hardfacing alloys, the effects of composition on microstructure and hardness were investigated in a progression of alloys. Initially, seven new alloys were prepared varying the carbon-boron ratio with the total constant at 3 wt%. Small arc-melt cast circular ingots were produced roughly 1 x 0.5 inches. Metallography provided insufficient phase magnification, thus a SEM equipped with EDS was used, allowing for microstructure and phase composition analysis. Four distinct carbide phases were found and image analysis software allowed for carbide …

Characterization Of Aluminum-Boron Carbide Particulate Metal Matrix Composites, Eric Blank

Materials Engineering

The analysis of die-cast 380 aluminum-boron carbide particulate metal matrix composites (MMC) was performed in order to see if the samples had the required tensile strength of 300 MPa. 10wt% B4C die-cast samples were produced and tested. Half were heat treated to the T6 condition and the others were left as cast. Using ASTM standard B 557M it was found that the average tensile strength for the as-cast samples was 130 MPa and the heat treated samples had a tensile strength of 93 MPa. These values were both lower than expected. The heat treated samples were not expected to have …