Engineering Science and Materials Commons^™

Nanomechanical Analysis Of Insulinoma Cells After Glucose And Capsaicin Stimulation Using Atomic Force Microscopy, Ruiguo Yang, Ning Xi, King Wai-Chu Lai, Bei-Hua Zhong, Carmen Kar-Man Fung, Chen-Geng Qu, Donna H. Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Aim: Glucose stimulates insulin secretion from pancreatic islet β cells by altering ion channel activity and membrane potential in the β cells. TRPV1 channel is expressed in the β cells and capsaicin induces insulin secretion similarly to glucose. This study aims to investigate the biophysical properties of the β cells upon stimulation of membrane channels using an atomic force microscopic (AFM) nanoindentation system.

Methods: ATCC insulinoma cell line was used. Cell stiffness, a marker of reorganization of cell membrane and cytoskeleton due to ion channel activation, was measured in real time using an integrated AFM nanoindentation system. Cell height that …

Solving The Partial Differential Equation Of Vibrations With Interval Parameters Using The Interval Finite Difference Method, Brenda G. Medina

Open Access Theses & Dissertations

Accuracy and efficiency are among the main factors that drive today's innovative disciplines. As technology rapidly advances, efficiency takes on new meanings but what about accuracy? How accurate is accurate? Human error, uncertainties in measurement, and rounding errors are just some causes of inaccuracy. Interval Computations is an area that allows for such issues to be taken into account; for each measurement attained (for example), an interval can be built by considering the error associated with the measurement, and such an interval can be utilized in the mathematical computations of interest.

We consider the partial differential equation (PDE) of vibrations …

The Effect Of Cr, Si And B On The Oxidation Behavior On Three Nb-Based Alloys, David Alvarez

Open Access Theses & Dissertations

Nb-based alloys are of particular interest to replace the current Ni-based superalloys for high-temperature structural applications. One important limitation to improve the efficiency of gas-turbine engines is the temperature limit of current materials being used. By allowing the temperature to increase, the efficiency will increase. Nb-based alloys have high melting points and adequate mechanical properties but the oxidation resistance is still inadequate.

This research focuses on the oxidation behavior of three Nb-based alloys to study the effect of Cr and Si variation and look at the effect of Boron. Boron can form a glassy borosilicate which is viscous at high …

Fabrication And Characterization Of Nanocrystalline Yttrium Oxide Thin Films For Electronic Device Applications, Mudavakkat Vikas Haridas

Open Access Theses & Dissertations

This thesis presents the optimization of growth conditions for fabricating nanocrystalline Yttrium Oxide (Y2O3) thin films on silicon and optical grade, high quality quartz substrates in order to study its structural, optical and electrical properties for electronic device applications.

Commercially Y2O3 has proven to be difficult to fabricate at high quality due to its high temperature growth requirements and the need to alter established fabrication methods for electronic devices. A high temperature requirement for high quality poses a problem for research and analysis. This calls upon for an optimization of the growth conditions to facilitate fabrication of thin films for …

Preparation And Characterization Of Iron Oxide And Hydroxide Based Nanomaterials, Guillermo Carbajal Franco

Open Access Theses & Dissertations

Iron (Fe) oxides and hydroxides are common and abundant materials. They exhibit diverse crystal structures, properties and phenomena by virtue of which they find a wide range of scientific and technological applications. Controlled growth and manipulation of the specific structure and electronic behavior to meet the requirements of a given application is a challenging problem in view of many possible phases and composition of the resulting materials. The preparation method and experimental conditions will, therefore, significantly affect the properties and performance of Fe oxides and hydroxides. The goal of the project is to obtain Fe-based oxide/hydroxide catalytic materials and to …

Fundamental Studies Of Co-Base Superalloy Biomedical Prototypes Fabricated By Electron Beam Melting: Microstructures And Microstructural Architecture, Sara M. Gaytan

Open Access Theses & Dissertations

Rapid prototyping, especially electron beam melting (EBM) technology by ARCAM have proven to provide outstanding microstructural and mechanical properties on different alloys fabricated by this technology. Being a computer designed driven technology, complex components, that are hard or even impossible to fabricate by traditional manufacturing techniques, can be fabricated by layer-by-layer EBM technology.

Microstructural and mechanical properties are compared for an EBM femoral knee component prototype with a traditionally-fabricated and body-removed femoral knee implant. Block and cylindrical shape components fabricated by EBM were also analyzed for this project. The alloy utilized for these components is Co-26Cr-6Mo-0.2C characterized by the standards …

Ballistic Projectile Metallurgical Issues And Fundamentals: Aerosol Production In Rod Penetration Erosion And Erosion Phenomena Associated With Railgun Development, Brenda Ivette Machado

Open Access Theses & Dissertations

The issue is derived from ballistic erosion as it relates to nanoparticle production and respiration of these particles as a health concern ballistic erosion and ballistic erosion as it relates to railgun performance. A common thread between these two issues is dynamic recrystallization (DRX). DRX has been demonstrated to be the dominant mechanism for solid-state flow associated with ballistic projectile/target penetration and interaction, friction-stir welding phenomena, and other high-strain rate deformation phenomena.

Aerosol particulates collected on filters from ballistic penetration and erosion events for W-Ni-Co and W-Ni-Fe kinetic energy rod projectiles penetrating steel target plates were observed to be highly …

Development And Characterization Of The Oxidation Behavior Of Various High Temperature Niobium Based Alloys, Benedict Isabel Portillo

Open Access Theses & Dissertations

The oxidation response of various niobium based refractory alloys from the Nb-Mo-Si-B-X alloy system has been examined at temperatures between 700 and 1400°C in air. The development of these alloys was part of an ongoing effort to develop and discover a new materials system capable of replacing nickel based super alloys. Additions of titanium were found to provide limited oxidation resistance. A discontinuous layer of TiO2 was observed to from at temperatures above 1100°C. Alloys containing titanium additions were observed to suffer from pest oxidation at low and intermediate temperatures due to the development of Nb2O5. Poor oxidation resistance at …

Microstructural Architecture Developed In The Fabrication Of Solid And Open-Cellular Copper Components By Additive Manufacturing Using Electron Beam Melting, Diana Alejandra Ramirez

Open Access Theses & Dissertations

The fabrication of Cu components were first built by additive manufacturing using electron beam melting (EBM) from low-purity, atomized Cu powder containing a high density of Cu2O precipitates leading to a novel example of precipitate-dislocation architecture. These microstructures exhibit cell-like arrays (1-3µm) in the horizontal reference plane perpendicular to the build direction with columnar-like arrays extending from ~12 to >60 µm in length and corresponding spatial dimensions of 1-3 µm. These observations were observed by the use of optical metallography, and scanning and transmission electron microscopy. The hardness measurements were taken both on the atomized powder and the Cu components. …

Effect Of Process Parameter On Temperature Distribution, Microstructure, And Mechanical Properties Of Self-Reacting Friction Stir Welded Aluminum Alloy 6061-T651, Monica Adriana Torres

Open Access Theses & Dissertations

Self-reacting friction stir welding is the latest FSW tool configuration developed, it employs two shoulders--one on top and one on the bottom of the workpiece-- this tool configuration offers many advantages over conventional welding techniques. However, the current lack of information and specifications limits its understanding and application. This investigation analyzed the effect of process parameters on temperature distribution, microstructure evolution, and final mechanical properties of 6061-T651 SR-FS welds. A factorial experiment was carried out, in which three-process parameters were analyzed--rotational speed, travel speed, and tool plunge force-- three levels were analyzed for each parameter, except for a tool plunge …

Dispersive Wave Equations For Solids With Microstructure, A. Berezovski, Juri Engelbrecht, Mihhail Berezovski

Publications

The dispersive wave motion in solids with microstructure is considered in the one-dimensional setting in order to understand better the mechanism of dispersion. It is shown that the variety of dispersive wave propagation models derived by homogenization, continualisation, and generalization of continuum mechanics can be unified in the framework of dual internal variables theory.

Nanostructured Arrays For Sensing And Energy Storage Applications, Raghu Mangu

University of Kentucky Doctoral Dissertations

Vertically aligned multi walled carbon nanotube (MWCNT) arrays fabricated by xylene pyrolysis in anodized aluminum oxide (AAO) templates without the use of a catalyst, were integrated into a resistive sensor design. The steady state sensitivities as high as 5% and 10% for 100 ppm of NH₃ and NO₂ respectively at a flow rate of 750 sccm were observed. A study was undertaken to elucidate (i) the dependence of sensitivity on the thickness of amorphous carbon layers, (ii) the effect of UV light on gas desorption characteristics and (iii) the dependence of room temperature sensitivity on different NH_{3 …}

Droplet Motion On Miniaturized Ratchets, Jeong Tae Ok

LSU Doctoral Dissertations

The main objective of this study is to evaluate the feasibility of using miniaturized asymmetric structures to move liquid droplets and understand the driving mechanism. We developed the fabrication process for large area topological ratchets with the period ranging from millimeter down to sub-micrometer using micromachining techniques. Non-wetting superhydrophobic surfaces were successfully fabricated using soft UV or thermal nanoimprint lithography, reactive ion etching by oxygen plasma, and chemical surface modification by fluorinated silane vapor deposition. An accurate and reproducible experimental setup equipped with high speed camera and automatic injection system was established. Image processing tools allowed us to obtain various …

Polymer Based Microfabrication And Its Applications In Optical Mems And Biomems, Guocheng Shao

LSU Doctoral Dissertations

Due to its ease of fabrication, low cost and great variety of functionalities, polymer has become an important material in microfabrication. MEMS devices with polymer as the structure material have found applications in various fields, especially in BioMEMS and optical MEMS. In this dissertation, three polymer based microfabricated devices/components have been developed and tested. Various polymer based fabrication techniques, such as high aspect ratio SU-8 photolithography, three dimensional polydimethylsiloxane (PDMS) soft lithography, multi-layer soft lithography and PDMS double casting technique have been developed/studied and employed in the device fabrication process. The main contribution of this dissertation includes: (1) Developed two …

Characterization Of Novel Akermanite:Poly-E-Caprolactone Scaffolds For Bone Tissue Engineering Aapplications Combined With Human Adipose-Derived Stem Cells, Andre S. Zanetti

LSU Doctoral Dissertations

The development of porous materials useful as scaffolds for the sustained three-dimensional (3D) growth of human adipose-derived stem cells (hASC) is of particular interest to facilitate healing after musculoskeletal injuries. In this study, a composite porous material obtained by blending akermanite with poly-e-caprolactone (PCL) is proposed as novel alternative to bone tissue regeneration. The objectives of this study are (1) to characterize the akermanite:PCL scaffold properties; (2) to investigate the in vitro osteogenic potential of hASC loaded to optimal akermanite:PCL scaffolds; (3) to assess the metabolic activity and osteogenesis of hASC loaded to optimal akermanite:PCL scaffolds post-thawing using optimal cryopreservation …

Automated Semantic Understanding Of Human Emotions In Writing And Speech, Ricardo A. Calix

LSU Doctoral Dissertations

Affective Human Computer Interaction (A-HCI) will be critical for the success of new technologies that will prevalent in the 21st century. If cell phones and the internet are any indication, there will be continued rapid development of automated assistive systems that help humans to live better, more productive lives. These will not be just passive systems such as cell phones, but active assistive systems like robot aides in use in hospitals, homes, entertainment room, office, and other work environments. Such systems will need to be able to properly deduce human emotional state before they determine how to best interact with …

Anomalous Loss Of Toughness Of Work Toughened Polycarbonate, Shawn E. Meagher

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Glassy polymers such as polycarbonate (PC) can be toughened through compressive plastic deformation. The increase in toughness is substantial, showing as much as a fifteen fold increase in the amount of dissipated energy during failure for samples compressed to 50% plastic strain. This toughness increase can be reversed through thermal aging at temperatures below the glass transition temperature (T_g = 147°C).

The combined effect of plastic compression and thermal aging has been studied using Charpy, Single Edge Notch Bending (SENB), and Compact Tension (CT) tests. The tests mapped the response of samples cut along different orientations relative to the …

Hybrid Nanomanufacturing Process For High-Rate Polymer Nanofiber Production, Chad T. Peterson

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Nanotechnology and nanomaterials have the potential to revolutionize existing and create entirely new industries. Unique physical, mechanical, chemical, and biological properties of nanomaterials have been extensively documented in the last two decades. However, most nanomaterials are discontinuous in nature, creating problems with their processing and manipulation into devices and raising health concerns. Continuous nanofibers represent an emerging class of nanomaterials with critical advantages to applications. Continuous nanofibers are readily produced by electrospinning process comprising spinning polymer solutions in high electric fields. Electrospinning is a very economic top-down nanomanufacturing process that has been used to produce ultrafine continuous nanofibers from several …

Processing And Composition Effects On The Fracture Behavior Of Spray-Formed 7xxx Series Al Alloys, Mala M. Sharma, Constance W. Ziemian, Timothy J. Eden

Faculty Journal Articles

The fracture properties of high-strength spray-formed Al alloys were investigated, with consideration of the effects of elemental additions such as zinc,manganese, and chromium and the influence of the addition of SiC particulate. Fracture resistance values between 13.6 and 25.6 MPa (m)^1/2 were obtained for the monolithic alloys in the T6 and T7 conditions, respectively. The alloys with SiC particulate compared well and achieved fracture resistance values between 18.7 and 25.6 MPa (m)^1/2. The spray-formed materials exhibited a loss in fracture resistance (KI) compared to ingot metallurgy 7075 alloys but had an improved
performance compared to high-solute powder …

Me-Em Enewsbrief, December 2010, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.