Engineering Science and Materials Commons^™

Mechanical Properties And Degradation Of High Capacity Battery Electrodes: Fundamental Understanding And Coping Strategies, Yikai Wang

Theses and Dissertations--Chemical and Materials Engineering

Rechargeable lithium ion and lithium (Li) metal batteries with high energy density and stability are in high demand for the development of electric vehicles and smart grids. Intensive efforts have been devoted to developing high capacity battery electrodes. However, the known high capacity electrode materials experience fast capacity fading and have limited cycle life due to electromechanical degradations, such as fracture of Si-based electrodes and dendrite growth in Li metal electrodes. A fundamental understanding of electromechanical degradation mechanisms of high capacity electrodes will provide insights into strategies for improving their electrochemical performance. Thus, this dissertation focuses on mechanical properties, microstructure …

A Method For Iron Determination During Copper Electrometallurgy And Its Application To The Calculation Of Current Efficiency, Daniel Pedro Cruz

Open Access Theses & Dissertations

With the objective of developing statistical models that describe iron kinetics under typical copper electrolytes as well as its effects on current efficiency and influence in cathodic and anodic behavior, a detailed electrochemical analysis is done in this work as a contribution to implement hydrometallurgical processes in the refining or winning process to produce high purity copper.

This Thesis evaluates the oxidation-reduction potential (ORP) of the Fe3+/Fe2+ couple in the H2SO4-Fe2(SO4)3-FeSO4-H2O and H2SO4-CuSO4-Fe2(SO4)3-FeSO4-H2O systems, with addition of different copper concentrations and temperatures up to 70°, typically employed in the industry. This study further validates and expands a thermodynamic expression developed …

Processing, Structure And Mechanical Behavior Of Advanced Engineering Steels, Bing Yu

Open Access Theses & Dissertations

The concept of low lattice misfit and high-density of nanoscale precipitates obtained through solution treatment was adopted to obtain ultrahigh strength maraging steel without compromising elongation. An "ultrahigh strength-high toughness" combination was successfully obtained in 19Ni3Mo1.5Ti maraging steel with ultimate strength of ~1858 MPa and static toughness of ~110 MJ·m-3. Maraging steel had extremely high density (2.3Ã?1024 m-3) of nanoscale precipitates with minimum lattice misfit of less than 1% at the solutionization temperature of 820 oC. Two kinds of nanoscale precipitates, namely, η-Ni3(Ti,Mo) and B2-Ni(Mo,Fe) contributed to ultrahigh strength. The size of nanoscale precipitates governed the movement of dislocations, cutting …

Investigating Using Titanium Zirconium Molybdenum For Additively Manufacturing Aerospace Components, Justin Hunter Vanhoose

Open Access Theses & Dissertations

Mankind throughout history has possessed an innate characteristic to explore, migrating to new frontiers.The requirement for this travel is most broadly associated with the need to pursue more resources. Rockets have been used as a means of weapons since the Sung Dynasty in the thirteenth empire and have now been integrated for travel/transport. The sophistication of rocketry and propulsion has reached a level to where it is plausible that mankind will be a multi-planetary species. The space industry has grown significantly with the advancement of the sophistication of these rocket technologies. However, a specific challenge to overcome in the space …

Microstructure Evolution Of Chalcogenide Materials Via Molecular Dynamics, Sharmin Abdullah

Open Access Theses & Dissertations

The properties of a material are defined by its granular microstructure which is determined by its grain evolution and the types of grain boundaries present in the structure. For example, the performance of Cadmium Sulfide/Cadmium Telluride (CdS/CdTe) solar cells can be affected by the presence of grain boundaries which makes the study of grain structure evolution a very important part of solar cell performance optimization. Grain boundary mobilities are important properties in material science and engineering as they determine grain structures under given processing and operating conditions.

In this thesis, several computational tools were used to analyze the formation and …

Comparative Study Of Analytical Models Of The Gruneisen Parameter Of Metals As Function Of Pressure, Celia Garcia Amparan

Open Access Theses & Dissertations

Commonly used Gruneisen parameter (γ) models only hold accurate in limited regimes making them inapplicable for use over wide temperature-pressure conditions. The accuracy of these analytical models of γ and of the thermal expansion of solids are of particular interest as these are considered proxies for quantifying anharmonicity, which may be a significant contribution to the thermal pressure at high temperatures. This work reviews various definitions of γ and their relations to the equations of state and apply them to two simple metals: Tantalum (Ta) and Copper (Cu), for which a high body of experimental data exists. Classical Molecular Dynamics …

Direct Write 3d Printing Of Functional Ceramics, Jorge Angel Diaz

Open Access Theses & Dissertations

Humidity sensors are used in many industries and are important for ensuring quality and safety. Ceramic sensors are preferred because of their quick response time, ability to withstand high temperatures and excellent Chemical and mechanical stability. The manufacturing world has been moving toward additive manufacturing which is a form of synthesizing 3D tangible layer by layer in witch minimal waste is produced. Additive manufacturing also is known as 3D printing has opened new possibilities to design engineers by giving them design freedom and access to the layers of a part to allow embedded sensors. There is a category of ceramics …

Computational Studies On Perovskite-Metallofullerene Interface And Magnetic Properties Of Mn-Based Mixed Olivines, Bethuel Omutiti Khamala

Open Access Theses & Dissertations

Methyl ammonium lead halide (MAPbX3) perovskite based solar cells have recently emerged as promising class of materials for photovoltaic applications with efficiencies reaching over 22%. Designing interfaces with strong binding is vital to developing efficient, high-performing solar cells. Fullerene-based materials are widely employed as efficient electron acceptors and can serve as electron transporting layer in perovskite based solar cells. We have studied interfaces of methyl ammonium lead iodide MAPbI3 with Sc3N@C80 fullerene and Sc3N@C80PCBM fullerene derivate within the density functional formalism. Different surface terminations and orientations of the methyl ammonium are examined for binding of the fullerene layer. Our calculated …

Fast Growth Of Thin Mapbi3 Crystal Wafers On Aqueous Solution Surface For Efficient Lateral-Structure Perovskite Solar Cells, Ye Liu, Qingfeng Dong, Yanjun Fang, Yuze Lin, Yehao Deng, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Solar-grade single or multiple crystalline wafers are needed in large quantities in the solar cell industry, and are generally formed by a top-down process from crystal ingots, which causes a significant waste of materials and energy during slicing, polishing, and other processing. Here, a bottom-up technique that allows the growth of wafer-size hybrid perovskite multiple crystals directly from aqueous solution is reported. Single-crystalline hybrid perovskite wafers with centimeter size are grown at the top surface of a perovskite precursor solution. As well as saving raw materials, this method provides unprecedented advantages such as easily tunable thickness and rapid growth of …

High Strength, Deformable Nanotwinned Al–Co Alloys, S. Xue, Qiang Li, D. Y. Xie, Y. F. Zhang, Han Wang, Haiyan Wong, J. Wang, Xinghang Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

Aluminum (Al) alloys have been widely used in the transportation industry. However, most highstrength Al alloys to date have limited mechanical strength, on the order of a few hundred MPa, which is much lower than the flow stress of high-strength steels. In this study, we show the fabrication of nanocrystalline Al alloys with high-density growth twins enabled by a few atomic percent of Co solute. In situ uniaxial compression tests show that the flow stress of Al–Co solid solution alloys exceeds 1.5 GPa, while good work hardening capability is maintained. This study provides a new perspective on the design of …

A Sensorless Force-Feedback System For Robot-Assisted Laparoscopic Surgery, Baoliang Zhao, Carl A. Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

The existing surgical robots for laparoscopic surgery offer no or limited force feedback, and there are many problems for the traditional sensor-based solutions. This paper builds a teleoperation surgical system and validates the effectiveness of sensorless force feedback. The tool-tissue interaction force at the surgical grasper tip is estimated using the driving motor’s current, and fed back to the master robot with a position-force bilateral control algorithm. The stiffness differentiation experiment and tumor detection experiment were conducted. In the stiffness differentiation experiment, 43 out of 45 pairs of ranking relationships were identified correctly, yielding a success rate of 96%. In …

Effects Of Compositional Tailoring On Drug Delivery Behaviours Of Silica Xerogel/Polymer Core-Shell Composite Nanoparticles, Wenfei Huang, Chi Pong Tsui, Chak Yin Tang, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Conventional core-shell polymer nanoparticles usually exhibit a rapid release rate with their release kinetics mainly adjusted through changing composition of the polymer shells, limiting their applications for prolonged drug delivery. As a solution to these problems, silica xerogel/polymer core-shellstructured composite nanoparticles have been proposed. Different with our previous work centring on studying process variables, we here focused on investigating the effects of key compositional variables on essential properties of the composite nanoparticles. The drug release profiles (in vitro) were well interpreted by the Baker and Lonsdale model on a predicted two-stage basis. The first stage (<1 day) was well controlled from 18.6% to 45.9%; the second stage (1–14 days) was tailored in a range from 28.7 to 58.2% by changing the composition of the silica xerogel cores and polymeric shells. A substantial achievement was reducing the release rate by more than 40 times compared with that of conventional polymer nanoparticles by virtue of the silica xerogel cores. A semi-empirical model was also established in the first attempt to describe the effects of polymer concentration and drug loading capacity on the size of the composite nanoparticles. All these results indicated that the composite nanoparticles are promising candidates for prolonged drug delivery applications.

Monolithic Heat-Transfer Device, Sidy Ndao, George Gogos, Dennis Alexander, Troy Anderson, Craig Zuhlke

Department of Mechanical and Materials Engineering: Faculty Publications

A monolithic heat-transfer device can include a container wall configured to retain a working fluid, where the container wall is formed of a single material. The container wall also includes an interior surface configured to be in fluid communication with the working fluid. The monolithic heat-transfer device also includes a channel disposed in the interior surface of the container wall, where the channel comprises a microstructure and a nanostructure. The microstructure and the nanostructure are materially contiguous with the single material forming the container wall. In some embodiments, the nanostructure comprises one or more layers of nanoparticles. The monolithic heat-transfer …

3d Printing Of Hybrid Mos2-Graphene Aerogels As Highly Porous Electrode Materials For Sodium Ion Battery Anodes, Emery Brown, Pengli Yan, Halil Tekik, Ayyappan Elangovan, Jian Wang, Dong Lin, Jun Li

Department of Mechanical and Materials Engineering: Faculty Publications

This study reports a 3D freeze-printing method that integrates inkjet printing and freeze casting to control both the microstructure and macroporosity via formation of ice microcrystals during printing. A viscous aqueous ink consisting of a molecular MoS₂ precursor (ammonium thiomolybdate) mixed with graphene oxide (GO) nanosheets is used in the printing process. Post-treatments by freeze-drying and reductive thermal annealing convert the printed intermediate mixture into a hybrid structure consisting of MoS₂ nanoparticles anchored on the surface of 2D rGO nanosheets in a macroporous framework, which is fully characterized with FESEM, TEM, XRD, Raman spectroscopy and TGA. The resulting …

Three-Dimensional Character Of The Deformation Twin In Magnesium, Y. Liu, P.Z. Tang, M.Y. Gong, R.J. Mccabe, J. Wang, C.N. Tome

Department of Mechanical and Materials Engineering: Faculty Publications

Deformation twins are three-dimensional domains, traditionally viewed as ellipsoids because of their two-dimensional lenticular sections. In this work, we performed statistical analysis of twin shapes viewing along three orthogonal directions: the ‘dark side’ (DS) view along the twin shear direction (η1), the twinning plane normal (TPN) view (k1) and the ‘bright side’ (BS) view along the direction λ(=k1 × η1). Our electron back-scatter diffraction results show that twins in the DS and BS views normally exhibit a lenticular shape, whereas they show an irregular shape in the TPN view. Moreover, the findings in the TPN view revealed that twins grow …

Spatiotemporal Characterizations Of Spontaneously Beating Cardiomyocytes With Adaptive Reference Digital Image Correlation, Akankshya Shradhanjali, Brandon D. Riehl, Bin Duan, Ruiguo Yang, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

We developed an Adaptive Reference-Digital Image Correlation (AR-DIC) method that enables unbiased and accurate mechanics measurements of moving biological tissue samples. We applied the AR-DIC analysis to a spontaneously beating cardiomyocyte (CM) tissue, and could provide correct quantifications of tissue displacement and strain for the beating CMs utilizing physiologically-relevant, sarcomere displacement length-based contraction criteria. The data were further synthesized into novel spatiotemporal parameters of CM contraction to account for the CM beating homogeneity, synchronicity, and propagation as holistic measures of functional myocardial tissue development. Our AR-DIC analyses may thus provide advanced non-invasive characterization tools for assessing the development of spontaneously …

Insulating Tunneling Contact For Efficient And Stable Perovskite Solar Cells, Jinsong Huang, Xiaopeng Zheng, Qi Wang, Yang Bai, Qingfeng Dong

Department of Mechanical and Materials Engineering: Faculty Publications

Perovskite-based photoactive devices, such as solar cells, include an insulating tunneling layer inserted between the perovskite photoactive material and the electron collection layer to reduce charge recombination and concomitantly provide water resistant properties to the device.

Beyond The Toolpath: Site-Specific Melt Pool Size Control Enables Printing Of Extra-Toolpath Geometry In Laser Wire-Based Directed Energy Deposition, Brian T. Gibson, Bradley S. Richardson, Tayler W. Undermann, Lonnie J. Love

Department of Mechanical and Materials Engineering: Faculty Publications

A variety of techniques have been utilized in metal additive manufacturing (AM) for melt pool size management, including modeling and feed-forward approaches. In a few cases, closed-loop control has been demonstrated. In this research, closed-loop melt pool size control for large-scale, laser wire-based directed energy deposition is demonstrated with a novel modification, i.e., site-specific changes to the controller setpoint were commanded at trigger points, the locations of which were generated by the projection of a secondary geometry onto the primary three-dimensional (3D) printed component geometry. The present work shows that, through this technique, it is possible to print a specific …

Disposable Fluidic Self-Propelling Robot For Traversing A Tubular Passage, Carl Nelson, Benjamin Terry, Abolfazl Pourghodrat, Hossein Dehghani, Dmitry Oleynikov, Prithviraj Dasgupta

Department of Mechanical and Materials Engineering: Faculty Publications

A probe for traversing a tubular passage includes an introducer to be supported at an entrance to the tubular passage. The probe also includes a probe tip to traverse the tubular passage, and a tube with an inflatable tube segment. In some embodiments, the inflatable tube segment is storable in the probe tip. The inflatable tube segment is configured to be inflated to push the probe tip away from the introducer toward an end on the tubular passage. In some embodiments, the probe includes a sealing mechanism, whre the sealing mechanism can be positioned between the inflatable tube segment of …

การศึกษาอิงพารามิเตอร์ของการควบคุมอุณหภูมิเชิงคาบในช่องปิดสองช่องที่ติดกันด้วยการจำลองเชิงเลข, เทิดพงศ์ ช่วยแก้ว

Chulalongkorn University Theses and Dissertations (Chula ETD)

งานวิจัยนี้ศึกษาผลของปัจจัยต่างๆ ที่ส่งผลต่อการควบคุมอุณหภูมิเชิงคาบในช่องปิดสี่เหลี่ยมจัตุรัสสองช่องที่ติดกันแยกจากกันด้วยผนังร่วม โดยทีแต่ละช่องปิดมีการควบคุมอุณหภูมิด้วยเครื่องทำความร้อนแบบเปิดปิดแยกกันอย่างอิสระ การศึกษาใช้โปรแกรม ANSYS FLUENT 2019 จำลองการถ่ายเทความร้อนแบบการพาความร้อนตามธรรมชาติของอากาศที่มีการไหลแบบราบเรียบในช่องปิดและการนำความร้อนของผนังร่วมเมื่อเรย์เลห์นัมเบอร์มีค่าประมาณ 105 โดยกำหนดให้เครื่องทำความร้อนเปิดเมื่ออุณหภูมิเฉลี่ยในช่องปิดต่ำกว่า 299 K และปิดเมื่ออุณหภูมิเฉลี่ยในช่องปิดสูงกว่า 301 K ผลการจำลองแสดงว่าไม่ว่าจะเริ่มการควบคุมอุณหภูมิเมื่อใดก็ตาม เมื่อเวลาผ่านไป คาบของการควบคุมจะเข้าสู่สภาวะคงตัวโดยที่การเปลี่ยนแปลงของอุณหภูมิเชิงคาบของทั้งสองช่องจะปรับจนมีค่าสอดคล้องใกล้เคียงกัน นอกจากนี้จากการศึกษาผลของสมบัติของผนังร่วมต่อการควบคุมอุณหภูมิเชิงคาบ 3 ชนิด ได้แก่ ทองแดง อลูมิเนียม และนิกเกิล พบว่าผนังร่วมที่ทำด้วยอลูมิเนียม ซึ่งมีค่า Thermal storage ต่ำที่สุด จะทำให้ของการควบคุมอุณหภูมิเชิงคาบเข้าสู่สภาวะคงตัวและการสอดคล้องของอุณหภูมิของสองช่องได้เร็วที่สุด และในการศึกษาผลของอุณหภูมิภายนอกพบว่าอุณหภูมิภายนอกมีผลต่อคาบของการควบคุมอุณหภูมิเชิงคาบอย่างมาก โดยเมื่ออุณหภูมิภายนอกสูงขึ้นจะทำให้ระยะเวลาเปิดเครื่องทำความร้อนสั้นลงในขณะที่ระยะเวลาปิดยาวขึ้น และใช้เวลาเข้าสู่สภาวะคงตัวของการควบคุมเชิงคาบและการสอดคล้องกันของอุณหภูมิของสองช่องนานขึ้นด้วย ซึ่งส่งผลโดยรวมให้คาบการควบคุมยาวขึ้น เมื่ออุณหภูมิภายนอกสูงเกินกว่า 298.15 K พบว่าอุณหภูมิของช่องปิดทั้งสองช่องไม่มีการปรับตัวเข้าหากัน