Environmental Engineering Commons^™

A Financial Impact Assessment Of Ld 1725: Stream Crossings Presentation, New England Environmental Finance Center

Economics and Finance

This report looks at the potential financial impact of LD 1725 on the estimated 30,000 stream crossings in the State of Maine that would be affected by the law. Our research for this report included the analysis of nearly 2000 stream crossings and the data collection necessary for the development of extensive stream crossing replacement cost models. We found that the 1.2 bankfull requirements in LD 1725 would result in a 75% ‐ 250% increase in structure widths for stream crossing projects across the state. An upsize of this magnitude would increase the cost of replacing stream crossings statewide by …

The Effects Of Tank Operation And Design Characteristics On Water Quality In Distribution System Storage Tanks, Christopher T. Olson, Delvin Deboer

Water and Environmental Engineering Research Reports

From the Executive Summary

Background:
Regional water systems utilize storage facilities to meet demand variations and pressure requirements of their systems. These storage facilities drain and fill in response to system water demands and water level control settings. Storage tanks are typically placed in strategic locations to maintain a consistent pressure in the distribution system. Storage facilities should be designed and operated such that the water is mixed to prevent stagnant water (old water that remains in the tank for an extended period). Stagnant water can lead to water quality issues, such as low disinfectant residuals, potential for microbial contamination, …

Effect Of Additive On The Performance Characteristics Of Centrifugal And Progressive Cavity Slurry Pumps With High Concentration Fly Ash Slurries, Sunil Chandel, S.N. Singh, V. Seshadri

Coal Combustion and Gasification Products Journal Archive

Slurry pumps that are used in the hydraulic transportation of fly ash slurries through pipes in thermal power plants can be broadly classified into two main categories namely positive displacement and centrifugal pumps. The two types of pumps differ considerably in construction as well as in operating principle compared to the conventional pumps. The present study reports the effect of additive on the performance characteristics of centrifugal and progressive cavity screw pumps with fly ash slurries at high concentrations (above Cw < 50% by weight). Mixture of sodium carbonate and Henko detergent (5:1) at a concentration of 0.2% by weight has been used as an additive. For each type of pump, the effect of additive on the performance characteristics has been experimentally evaluated at rated speed with fly ash slurries in the concentration range of 50 to 70% by weight. The pump total head, overall efficiency and pump input power as a function of flow rate have been measured. The results obtained from the centrifugal slurry pump performance show that at rated speed, the performance of the pump improves with the addition of drag reducing additive. In the case of progressive cavity screw pump, pump performance characteristics and behavior were completely different as compared to the centrifugal slurry pump. At rated speed, the performance of screw pump deteriorates with the addition of drag reducing soap solution.

Accidental Releases Of Hazardous Materials And Relevance To Terrorist Threats At Industrial Facilities, Laura J. Steinberg, Nicholas Santella

Civil and Environmental Engineering - All Scholarship

Hazardous material releases, some with serious consequences, are a common occurrence in the U.S. Of late, the hazards posed by releases caused by terrorist attacks or natural disasters have been of particular concern. Although terrorism directed at hazardous material handling industries within the U.S. has not yet resulted in a significant incident, there is much recent experience with serious accidental releases resulting from natural disasters. Case studies are developed from a number of recent natural disasters and severe weather events that resulted in large releases of hazardous materials. These case studies are used to illustrate parallels between the risks posed …

Spatial And Temporal Patterns Of Mercury Accumulation In Lacustrine Sediments Across The Laurentian Great Lakes Region, Paul E. Drevnick, Daniel R. Engstrom, Charles T. Driscoll, Edward B. Swain, Steven J. Balogh

Civil and Environmental Engineering - All Scholarship

Data from 104 sediment cores from the Great Lakes and “inland lakes” in the region were compiled to assess historical and recent changes in mercury (Hg) deposition. The lower Great Lakes showed sharp increases in Hg loading c. 1850-1950 from point-source water dischargers, with marked decreases during the past half century associated with effluent controls and decreases in the industrial use of Hg. In contrast, Lake Superior and inland lakes exhibited a pattern of Hg loading consistent with an atmospheric source - gradual increases followed by recent (post-1980) decreases. Variation in sedimentary Hg flux among inland lakes was primarily attributed …

2011 Nebraska Water Monitoring Programs Report, Marty Link

Nebraska Department of Environmental Quality: Reports

The Nebraska Department of Environmental Quality (NDEQ) is charged with monitoring, assessing, and to the extent possible, managing the state’s water resources. The purpose of this work is to protect and maintain good quality water and encourage or execute activities to improve poor water quality. Monitoring is done on the over 18,000 miles of flowing rivers and streams, our greater than 280,000 acres of surface water in lakes and reservoirs, and the vast storage of groundwater in Nebraska’s aquifers.

Effects Of Nitrogen Deposition And Empirical Nitrogen Critical Loads For Ecoregions Of The United States, Linda H. Pardo, Mike E. Fenn, Christine L. Goodale, Linda. H. Geiser, Charles T. Driscoll, Edith B. Allen, Jill S. Baron, Roland Bobbink, Williams D. Bowman, Christopher M. Clark, Bridget Emmett, Frank S. Gilliam, Tara L. Greaver, Sharon J. Hall, Erik A. Lilleskov, Lingli Liu, Jason A. Lynch, Knute J. Nadelhoffer, Steven S. Perakis, Molly J. Robin-Abbott, John L. Stoddard, Kathleen C. Weathers, Robin L. Dennis

Civil and Environmental Engineering - All Scholarship

Human activity in the last century has led to a significant increase in nitrogen (N) emissions and atmospheric deposition. This N deposition has reached a level that has caused or is likely to cause alterations to the structure and function of many ecosystems across the United States. One approach for quantifying the deposition of pollution that would be harmful to ecosystems is the determination of critical loads. A critical load is defined as the input of a pollutant below which no detrimental ecological effects occur over the long-term according to present knowledge.

The objectives of this project were to synthesize …

Infrared-Based Measurements Of Velocity, Turbulent Kinetic Energy, And Dissipation At The Water Surface In A Tidal River, C. Chris Chickadel, Stefan A. Talke, Alexander R. Horner-Devine, Andrew T. Jessup

Civil and Environmental Engineering Faculty Publications and Presentations

Thermal infrared (IR) based particle image velocimetry (PIV) is used to measure the evolution of velocity, turbulent kinetic energy (TKE), and the TKE dissipation rate at the water surface in the tidally influenced Snohomish River. Patterns of temperature variability in the IR imagery arise from disruption of the cool skin layer and are used to estimate the 2D velocity field. Comparisons of IR based PIV mean velocity made against a collocated acoustic velocimeter demonstrate high correlation (r2 > 0.9). Over a tidal period, surface TKE computed from the IR velocity varies from 10-4 J·kg-1 to 3x10-3 J·kg-1, with an average difference …

Environmental Study Of Solid Waste Collection, Mousa Awad Maimoun

Electronic Theses and Dissertations

The growing municipal solid waste generation rates have necessitated more efficient, optimized waste collection facilities. The majority of the US collection fleet is composed of diesel-fueled vehicles which contribute significant atmospheric emissions including greenhouse gases. In order to reduce emissions to the atmosphere, more collection agencies are investigating alternative fuel technologies such as natural gas, biofuels (bio-gas and bio-diesel), and hybrid electric technology. This research is an in-depth environmental analysis of potential alternative fuel technologies for waste collection vehicles. This study will evaluate the use of alternative fuels by waste collection vehicles. Lifecycle emissions, cost, fuel and energy consumption were …

Mass Conservation Analysis For The Lower St. Johns River Using Continuous And Discontinuous Galerkin Finite Element Methods, Lillie E. Thomas

Electronic Theses and Dissertations

This thesis provides a mass conservation analysis of the Lower St. Johns River for the purpose of providing basis for future salinity transport modeling. The analysis provides an assessment of the continuous (CG) and discontinuous (DG) Galerkin finite element methods with respect to their mass conservation properties. The following thesis also presents a rigorous literature review pertaining to salinity transport in the Lower St. Johns River, from which this effort generates the data used to initialize and validate numerical simulations. Two research questions are posed and studied in this thesis: can a DG-based modeling approach produce mass conservative numerical solutions; …

Identification Of Holocarboxylase Synthetase Chromatin Binding Sites In Human Mammary Cell Lines Using The Damid Technology, Dipika Singh, Angela K. Pannier, Janos Zempleni

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Holocarboxylase synthetase (HCS) is a chromatin protein that is essential for mediating the covalent binding of biotin to histones. Biotinylation of histones plays crucial roles in the repression of genes and repeats in the human genome. We tested the feasibility of DNA adenine methyltransferase identification (DamID) technology to map HCS binding sites in human mammary cell lines. Full-length HCS was fused to Dam for subsequent transfection into breast cancer (MCF-7) and normal breast (MCF-10A) cells. HCS docking sites in chromatin were identified by using the unique adenine methylation sites established by Dam in the fusion construct; docking sites were unambiguously …

Zinc Speciation In Power Plant Burning Mixtures Of Coal And Tires, Luis F.O. Silva, Marcos L.S. Oliveira, Carmen Serra, James C. Hower

Coal Combustion and Gasification Products Journal Archive

Fly ash from the cyclone-boiler co-combustion of high-S, high volatile bituminous coal and tire-derived fuel (tdf) was studied using a variety of chemical, optical, and microbeam techniques. Fly ash, dominated by Al-Si glass with lesser amounts of coalderived carbons, Fe-spinels, and tire-derived carbons, has Zn concentrations ranging from 2200 ppm (1st ESP row) to 6900 ppm Zn (3rd ESP row). Zinc occurs in Zn-rich nanoparticles in the Al-Si glass phases and as ZnO in amorphous and crystalline nanominerals, Fe- and Zn-sulfides, Pb-Al-Fe sulfates, and Zn sulfates. Iron-rich, Al- and Ti-bearing spinels contain accessory Zn2+,Cr3+,Mn2+, and Pb2+. Fe-sulfates and phosphates nanoparticles …

Co-Disposal Of Dry Fgd By-Product With Coal Gasification Ash And Inorganic Brines, Jabulani S. Mahlaba, P.C. Pretorius, Subal Maharajh, M.P. Augustyn

Coal Combustion and Gasification Products Journal Archive

There is a growing pressure from the environmental authorities and public bodies to reduce anthropogenic pollution. Stringent environmental legislation is being implemented for industries around the world, even more so for coal consuming industries. Control of gaseous emissions is one of the areas that are receiving considerable attention towards sustainable development. Coal combustion in coal-fired power utilities emits SO~x~ to the atmosphere. Dry flue gas desulphurisation (FGD) is a well known technology often used to mitigate sulphur emissions in coal-fired power utilities. It traditionally uses lime to neutralise SO~x~, and forms a mixture of anhydrite (CaSO~4~), and calcium sulphite (CaSO~3~). …

Irrigation Efficiency And Uniformity, And Crop Water Use Efficiency, Suat Irmak, Lameck O. Odhiambo, William L. Kranz, Dean E. Eisenhauer

Department of Agricultural and Biological Systems Engineering: Faculty Publications

This Extension Circular describes various irrigation efficiency, crop water use efficiency, and irrigation uniformity evaluation terms that are relevant to irrigation systems and management practices currently used in Nebraska, in other states, and around the world. The definitions and equations described can be used by crop consultants, irrigation district personnel, and university, state, and federal agency personnel to evaluate how efficiently irrigation water is applied and/or used by the crop, and can help to promote better or improved use of water resources in agriculture.

As available water resources become scarcer, more emphasis is given to efficient use of irrigation water …

Magnetite Nanoparticles For Medical Mr Imaging, Zachary R. Stephen, Forrest M. Kievit, Miqin Zhang

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Magnetic resonance imaging (MRI) has become one of the most widely used and powerful tools for non-invasive clinical diagnosis due to its high soft tissue contrast, spatial resolution, and penetration depth1. In addition, images are acquired without the use of ionizing radiation or radiotracers that would cause unwanted harmful side-effects. A considerable amount of research in medical MR imaging is focused on the development of contrast agents that can provide better delineation between healthy and diseased tissue. Magnetic nanoparticles (MNPs) are a major class of nanoscale material currently under extensive development for improved diagnosis of a wide range of diseases, …

A Multi-Analytical Approach To Understand The Chemistry Of Fe-Minerals In Feed Coals And Ashes, Marcos L.S. Oliveira, Frans Waanders, Luis F.O. Silva, Andre Jasper, Carlos H. Sampaio, Dursman Mchabe, Rachel S. Hatch, James C. Hower

Coal Combustion and Gasification Products Journal Archive

Seven feed coals used in the Brazilian power generation industry were obtained and subsequently analysed together with fly ash and bottom ash from a major Brazilian power plant. The samples were investigated by means of room temperature FeMo¨ssbauer analyses, X-ray diffraction, Raman spectroscopy, scanning electron microscope and petrographic analysis. In addition, nanometer-sized crystalline phases in coals and ashes were characterised using an energy-dispersive X-ray spectrometer and a high-resolution transmission electron microscope. The major identified Fe-bearing minerals in the coals were found to be actinolite, ankerite, chalcopyrite, chlorite, goethite, illite, ilmenite, magnesioferrite, natrojarosite, pyrite, pyrrhotite, and siderite; whilst in the fly …

Compositional Variations In Pilot Gasifier And Laboratory-Produced Slags And Their Impacts On Slag Viscosity And Coal Assessment, Alexander Ilyushechkin, Daniel Roberts, David Harris

Coal Combustion and Gasification Products Journal Archive

The flow behaviour of coal mineral matter at high temperatures is an important parameter for coal use in entrained-flow gasification technologies. Recently, gasification performance data was obtained from a series of pilot-scale gasification tests on a suite of well-characterised Australian black coals. Evaluation of the results of the pilot tests and the detailed laboratory investigations provided the opportunity for evaluation of the practical applicability of different laboratory and modelling techniques for coal assessment in terms of mineral matter behaviour in entrained flow gasification. A series of viscosity measurements was made over the range 1200–1600uC using slags produced in a pilot …

Compaction Of High-Ca Fly Ash-Al- And Al-Alloy-Composites: Evaluation Of Their Microstructure And Tribological Performance, Grigorios Itskos, Angeliki Moutsatsou, Pradeep K. Rohatgi, Nikolaos Koukouzas, Charalampos Vasilatos, Eleni Katsika

Coal Combustion and Gasification Products Journal Archive

In this study, highly calcareous and siliceous fly ash particles were utilized for the fabrication of Al- and Al-alloy-based MetalMatrix Composites (MMCs) by means of powder metallurgy. After compacting and sintering Al and Al/Si powders containing 10, 15, and 20wt. % ash particles, the homogenous (and with minimal amount of voids) microstructure of the produced composites was verified by means of Scanning Electron Microscopy (SEM). The composites were tested for their dry sliding wear behavior using a pin-on-disc machine against spheres of alumina. The worn surfaces of composites were then examined by using SEM and Energy Dispersive X-Ray Spectroscopy (EDS). …

Influence Of Chemical Reagents On Rheological Properties Of Fly Ash-Water Slurry At Varying Temperature Environment, H.K. Nail, M.K. Mishra, Karanam U.M. Rao

Coal Combustion and Gasification Products Journal Archive

About 70% of total electrical energy is generated from thermal power plants in India which in turn release about 160 Mt of fly ash as solid waste annually. Transportation and disposal of such a huge amount of fly ash is a major problem faced by the power plants. Presently fly ash is transported as lean slurry in pipe lines requiring about 80 to 85% of water with high energy input. A major impediment in high volume transportation of fly ash is its high specific gravity as compared to that of water. The objective of the present study was to evaluate …

Impact Of Manufactured Coal Ash Aggregates On Water Quality During Open Pit Restoration: 1. A Statistical Screening Test, Sangchul Hwang, Isomar Latorre

Coal Combustion and Gasification Products Journal Archive

Utilization of manufactured coal ash aggregates (MAs) as a subsoil substitute during restoration of an open pit was assessed in a three-factor, two-level factorial analysis. The factors of interest were the MA application rate (2:1 or 1:2 topsoil/MA volume ratio), rainfall intensity (high or low), and aggregate size (2.36–4.75 mm or 4.75–9.53 mm). Among the water quality parameters examined (pH, turbidity, heavy metal content (lead and cadmium), conductivity, and hardness), the last two parameters were significantly higher (p,0.05) in soil amended with MAs than in a control reactor using sand. A low rainfall intensity and larger aggregate size resulted in …