Construction Engineering and Management Commons^™

The Design Of A Modelling, Monitoring And Validation Method For A Solid Wall Structure, Timothy O'Leary, Gillian Menzies, Aidan Duffy

Conference Papers

Hygrothermal assessment is the combined analysis of heat, air and moisture transfer through the building fabric. The two approaches are covered by conventions known as the IS EN 5250:2011 (Glaser method) and IS EN 15026:2007 which differs from Glaser by solving the equations numerically using computer software. Results for hygrothermal analysis provide valuable information for surface and interstitial condensation risk assessment and the impact of energy upgrades. For traditional solid walled structures, conditions such as wind driven rain (WDR) and rising ground water can have a significant impact on the environmental behaviour and in particular the moisture behaviour of the …

The Role Of Shrinkage Strains Causing Early-Age Cracking In Cast-In-Place Concrete Bridge Decks, Tayyebeh Mohammadi, Baolin Wan, Christopher M. Foley

Civil and Environmental Engineering Faculty Research and Publications

Early-age cracking in cast-in-place reinforced concrete bridge decks is occurring more frequently now than three decades ago and principle factors that lead to early-age deck cracking are not fully understood. A finite element (FE) simulation methodology for assessing the role of shrinkage-induced strains in generating early-age bridge deck cracking is described. The simulations conducted indicate that drying shrinkage appears to be capable of causing transverse (and possibly longitudinal) bridge deck cracks as early as 9 to II days after bridge deck placement. The drying-shrinkage induced stresses would result in transverse cracking over interior pier supports in a typical bridge superstructure …

Using Simulated Virtual Interactivity In Construction Education, Saeed Rokooei, James D. Goedert

Department of Construction Engineering and Management: Faculty Publications

This paper briefly illustrates the design procedure, implementation and findings of a three year research project. Virtual Interactive Construction Education (VICE) is a project-based pedagogical model that uses a simulated environment to alter traditional subject-based lectures into virtual project-based interactive learning methods in construction education. For this purpose, the context of construction engineering and management curricula were aggregated into six construction project prototypes. VICE-Bridge is the first of these six prototypes that exposes players to experiential problem solving activities toward achieving a goal situation (construct the bridge) from an initial situation (start of construction). It was designed for students with …

Early-Age Hydration Studies Of Portland Cement, Fengjuan Liu

Electronic Theses and Dissertations

Our current knowledge on cement hydration during setting is based on the discrete observation of hydrated paste. An advanced micro/nano-level technique which can perform the in-situ observation on the continuous hydration of cement paste is demanded. In this study, Raman spectroscopy (RS) was chosen as such a method to continuously investigate wet pastes. The objective of this research is to explore the hydration process and microstructural development of fresh pastes with this technique. This research was conducted in three phases. First, the RS analysis was used to continuously observe the cement hydration from 20 minutes after mixing to 9 hours. …

A Strategic Approach To Effectively Manage Supplier Quality Within The Construction Industry, Rufaidah Almaian

Graduate Theses and Dissertations

The aim of the research is to determine the best practices for supplier quality management (SQM) in the construction industry that ensure that the supplied materials and equipment for construction projects are within the quality requirements. The research is based on three main objectives. The first objective is to describe and assess the process of assuring supplier quality inside and outside the construction industry. The second objective is to develop a framework for the supplier quality process based on the collection of SQM practices from multiple data sources. The third objective is to assess the SQM practices within the developed …

Bs News November/December

Building Services Engineering

No abstract provided.

Interdisciplinary, Collaborative International Service Learning: Developing Engineering Students As Global Citizens, Anthony D. Songer, Karen R. Breitkreuz

Construction Management Faculty Publications and Presentations

Recent calls to reform engineering education place emphasis on applied math and science within the broader context of globalization, economics, the environment, and society. This broad and complex challenge necessitates the investigation of new interdisciplinary education approaches for engineering education. This paper presents a formal approach for developing engineering students as global citizens. The 360 Degree Model for Educating Socially Responsible Global Citizens (360 Global Ed model) presented herein includes a framework for foundational theory, educational environment, academic coursework, and outcomes. At the core of the emerging model is an international service learning experience called the Village Network. …

Construction Management Service Learning: A "How To" Process For Success, R. Casey Cline, Ken Robson, Michael Kroth

Construction Management Faculty Publications and Presentations

To ensure that students are prepared for positions in the construction industry, construction management education programs expose students to industry relevant construction management (CM) theory and practice. Traditional transmission teaching methodologies, while arguably effective for teaching management theory and practice, are not as effective for the transfer of practical leadership skills and knowledge of construction specific processes. As an alternative teaching strategy, many CM programs incorporate service-learning (S-L) into curricula; providing students practical experience, focusing on the acquisition of knowledge through goal setting, thinking, planning, experimentation, observation, and reflection.

However, from a practical standpoint, the development of a service-learning project …

Bs News September/October

Building Services Engineering

No abstract provided.

A Cost Benefit Analysis Of Improving Energy Efficiency Of A Fitness Facilty, Inuri A. Illeperuma

Journal of Environmental and Resource Economics at Colby

Abstract: Nearly 40% of the total U.S. energy consumption in 2012 was consumed in residential and commercial buildings, as recorded by U.S. Energy Information Administration. With the urgent need to reduce overall energy consumption in the U.S., many efforts are made to improve the energy efficiency of buildings. However, energy managers identify budget constraints as one of the main obstacles in improving the energy efficiency of buildings. Hence this study focuses on a cost benefit analysis of improving the energy efficiency, with a special focus on fitness facilities in college environments. As a case study, the author focuses on improving …

Evaluating The Impact Of Bridge Deck Removal Method On The Performance Of Precast/Prestressed Concrete I-Girders, Shaddi Assad

Department of Construction Engineering and Management: Dissertations, Theses, and Student Research

Wide flange precast/prestressed concrete I-girders have been widely used by several State Departments of Transportation (DOTs) in the last two decades. These girders have many advantages over standard AASHTO I-girders. Their wide and thick bottom flange accommodates a large number of prestressing strands and their wide and thin top flange provides a shorter deck span, reduced girder weight, greater stability in construction, and adequate platform for workers. Despite these advantages, the wide and thin top flange might be disadvantageous when it comes to deck removal, as it is more susceptible to damage. Therefore there is a need to investigate the …

Development Of Improved Electrodeposition Method For Repair Of Reinforced Concrete Structures, Takahiro Nishida, Nobuaki Otsuki, Atsushi Saito

International Conference on Durability of Concrete Structures

Deterioration of reinforced concrete members and their repair methods have been reported in various concrete published reports. Electrodeposition method is one of these repair methods for repairing deteriorated concrete members using an electrochemical mechanism. The purposes of the electrodeposition method are to fill cracks in concrete and to coat the concrete surface by electrodeposits of chemical compounds. This can be accomplished by passing a weak direct current (1.0–3.0 A/m² of concrete surface area) between a reinforcing steel bar (cathode) in concrete and an external electrode (anode) located in an external solution near the concrete surface. This method also accomplishes …

Effects Of Stirrups On Bond Behavior Between Concrete And Corroded Steel Bars, Hongwei Lin, Yuxi Zhao, Ming Sun

International Conference on Durability of Concrete Structures

Steel corrosion leads to the deterioration of bond between concrete and steel bars. The serviceability and ultimate strength of concrete elements within RC structures are hence affected. Many researchers have studied the bond behavior of corroded steel bars. However, very few studies have investigated the effects of confinements on the degradation of bond strength. The present paper proposed a new kind of beam specimen based on which the effects of stirrups on degradation of bond were investigated. The test results proved that stirrups can effectively increase the bond strength between concrete and corroded steel bars.

Effect Of Blast Furnace Slag Powder And Fly Ash On Durability Of Concrete Mixed With Seawater, Nobuaki Otsuki, Takahiro Nishida, Chang Yi, Tomohiro Nagata, Hiroki Ohara

International Conference on Durability of Concrete Structures

According to the report of the United Nations, it is said that two-third of world population would be influenced by water shortage before 2050. To use fresh water effectively, the usage of seawater in concrete industry seems imperative. However, the usage of seawater as concrete material is prohibited in almost all the standards or specifications around the world. In this article, the usage of seawater as a material of concrete based on the results of experimental works and deterioration prediction was discussed. Especially, the effects of by-products such as blast furnace slag or fly ash on the durability of concrete …

Coastal Defenses, U.S., Bert Chapman

Libraries Faculty and Staff Scholarship and Research

Provides an overview of U.S. military coastal defenses during the period up to and including the War 1812.

An Investigation Of Project Delivery Methods Relating To Repetitive Commercial Construction, Donald A. Patterson

Theses and Dissertations

The Design/Bid/Build (DBB) delivery method has historically been the most popular and the most effective means of determining the least cost for building a project based upon a set of construction documents. In recent years, however, other project delivery methods, including but limited to Construction Manager/General Contractor (CM/GC) and Design/Build (DB), have slowly taken a share of the construction market away from the DBB delivery method. The choice of delivery method that will produce the best value for an owner in the measurements of efficiency in quality, cost, and timeliness depends upon the type of project and the business culture …

Creating Total Value Engineering Through Combining Design For Manufacturing And Design For Six Sigma Constructs, David Ryan Christensen

Theses and Dissertations

The modern manufacturing world has been driven to compete in a more international and interconnected system. This has led to increased focus upon frameworks and architectures to guarantee quality, high market acceptance, and reduce cost. Modern manufacturing design processes evolved largely from Henry Ford at Ford Motor Company, and Alfred Sloan at General Motors. Their structures embody two different focuses on quality and value engineering which have influenced many recent design frameworks. In the 1970s a heavy emphasis was placed upon Design for Manufacturing, which uses group technology, commonality of processes, and continual focus to reduce part count. Some companies …

Cypress Construction Inc.: Scheduling And Estimating Quandaries For Small Scale Residential Builds, Thamar Alsayyar

Master of Technology Management Plan II Graduate Projects

This study evaluates the particular scheduling and estimating challenges faced by Cypress Construction Incorporated, a small, privately owned residential construction company based in Baltimore, Maryland. The study, via the usage of primary data collection in the form of personal interviews and site observations, determines the nature of the scheduling and estimating functions conducted by Cypress Construction Inc.’s owner This data is then analyzed to ascertain why the scheduling and estimating functions of Cypress Construction Inc. are unique to the firm and are in need of amelioration. Furthermore, the study includes a literature review to compare the experiences of Cypress Construction …

Seismic Response Of A Tall Building To Recorded And Simulated Ground Motions, Nenad Bijelic, Ting Lin, Gregory Deierlein

Civil and Environmental Engineering Faculty Research and Publications

Seismological modeling technologies are advancing to the stage of enabling fundamental simulation of earthquake fault ruptures, which offer new opportunities to simulate extreme ground motions for collapse safety assessment and earthquake scenarios for community resilience studies. With the goal toward establishing the reliability of simulated ground motions for performance-based engineering, this paper examines the response of a 20-story concrete moment frame building analyzed by nonlinear dynamic analysis under corresponding sets of recorded and simulated ground motions. The simulated ground motions were obtained through a larger validation study via the Southern California Earthquake Center (SCEC) Broadband Platform (BBP) that simulates magnitude …

Bs News July/August

Building Services Engineering

No abstract provided.