Civil Engineering Commons^™

Galena Creek Bridge Structural Health Monitoring Instrumentation And Modeling, Leopold Falkensammer

UNLV Theses, Dissertations, Professional Papers, and Capstones

Structural health monitoring (SHM) of an instrumented structure provides numerous benefits when assessing the long-term condition of the structure against degradation, or the short-term condition after an extreme event, such as an earthquake. The Nevada Department of Transportation (NDOT) has an interest in expanding the use of SHM for such assessments. Accordingly, the objective of the current study is to develop and implement a permanent SHM system for the Galena Creek Bridge, the largest concrete cathedral arch bridge in the world, to monitor its response to routine traffic and seismic activity. Completed in 2012, the bridge connects Reno and Carson …

Effect Of Incorporating Pottery And Bottom Ash As Partial Replacement Of Cement, Bassam A. Tayeh, Doha M. Alsaffar, Lawend K. Askar, Asmahan Issa Jubeh

Karbala International Journal of Modern Science

This study addressed the environmental constraints in cement produc­tion. Ordinary Portland cement (OPC) was replaced with pottery powder (PP, produced by grinding locally available pottery) and bottom ash (BA) at 10%, 20% and 30% of cement mass. Moreover, 4% calcium chloride solution (CaCl₂.2H₂O) was used as mixing water. Material properties, such as standard consistency, setting time and compressive strength, were measured with different percentages of OPC replacement with PP and BA. Results indicated that the replacement with PP and BA increased the water demand to achieve the standard consistency. These results revealed that the strength evolution …

Lidar Assessment To Monitor Bridge Response Under Live And Dead Loads, Daniel Watson

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Understanding how a bridge structure responds to various loads in a time and resource-efficient approach is vital in characterizing bridge health. Bridge health monitoring is an evaluation of the structural condition and performance, which optimizes limited transportation budgets by prioritizing the bridges that are in the most need for retrofit or replacement. Identifying and remedying issues will mitigate long-term problems and ensure that the bridge remains open to service for all legal loads. In contrast, health monitoring and load rating will determine if a bridge can only carry traffic up to a certain weight or speed, requiring a bridge load …

Numerical Simulations Of The Hall–Petch Relationship In Aluminium Using Gradient-Enhanced Plasticity Model, Yooseob Song, Jaeheum Yeon, Byoungjoon Na

Civil Engineering Faculty Publications

+e Hall-Petch relation in aluminium is discussed based on the strain gradient plasticity framework. +e thermodynamically consistent gradient-enhanced flow rules for bulk and grain boundaries are developed using the concepts of thermal activation energy and dislocation interaction mechanisms. It is assumed that the thermodynamic microstresses for bulk and grain boundaries have dissipative and energetic contributions, and in turn, both dissipative and energetic material length scale parameters are existent. Accordingly, two-dimensional finite element simulations are performed to analyse characteristics of the Hall–Petch strengthening and the Hall–Petch constants. +e proposed flow rules for the grain boundary are validated using the existing experimental …

Static Analysis Of Circular Plates Under Mechanical Loads, Harpreet Lalia

Publications and Research

In this research statics analysis of circular plates is performed using SolidWorks.

Circular plates with different material properties, thickness to radius ratios, and boundary conditions under mechanical loads are modeled and analyzed in SolidWorks.

The results are obtained for deflections of circular plates under uniform and point loads.

A three-dimensional (3D) model of circular plates is first created in SolidWorks. Then the material properties, mechanical loads and boundary conditions are defined for the plate.

It is found deflection of plates is depended on magnitude of mechanical loads, geometrical parameters, boundary conditions and material properties. Responses of SolidWorks for deflections of …

Energy & Carbon Neutral Nyc, Evan Banks, Elena Zimareva, Elena Malysheva

Publications and Research

In 2016, the world's leading countries signed the Paris Agreement which focused on reducing anthropogenic climate change on the planet. On May 2019, New York State and New York City declared its own ambitious goals aimed at decarbonizing the city and restricting the state’s energy use to relying completely on renewables.

Some of these goals specifically target infrastructure in the city since estimates cite buildings as accounting for nearly 70% of New York’s energy use. The main law of New York’s Climate Policy, Local Law 97, requires all buildings over 25,000 sq ft to reduce their CO2 footprint by 40% …

Static Analysis Of Structural Members, Amani Calderon, Alexis Villalona, Farhad Alinaghizadeh

Publications and Research

This research is devoted to statics analysis of structural members under mechanical loads. Static analysis of beams under uniform transverse mechanical loads is presented. The beams are supported by simply supported boundary condition at both sides. The equilibrium equation of the beams is obtained and solved using analytical method and numerical method. The numerical method employed in this work is generalized differential quadrature (GDQ) method. The type of differential quadrature method used for numerical solution is the polynomial-based GDQ method. The differential equation is discretized into algebraic equations based on the GDQ technique. The algebraic equations are then solved to …

A New Synthesized Microalloys Steel Ods Of High Amplitude Ultrasonically Irradiation, Marzuki Silalahi, Hanif Abdurrahman Wicaksana, Ferhat Aziz, Syahfandi Ahda, Mohamad Riza Iskandar

Makara Journal of Technology

Micropowders of oxide-dispersion-strengthened (ODS) steel have been synthesized using the ultrasonic irradiation method with variations in amplitude. The ultrasonic irradiation process is performed for 50 h at a frequency of 20 kHz with 40%, 50%, and 60% amplitudes in toluene solution. The formation of Fe-Cr microalloys in the preparation of Fe- 15Cr-0.5Y2O3 powder was analyzed using SEM-EDS, X-ray diffraction (XRD), and TEM-EDS. The percentage of Fe- Cr phase mass fraction of ODS steel micropowder formed during ultrasonic irradiation with 40%:50%:60% amplitude was 12.2%:34.1%:22.1%, with 25.67:77.02:38.51 nm crystallite size. The crystallite size at 50% amplitude was the largest, and the diffusion …

Comprehensive Inspection On The Experimental Ferritic Stainless Steel By Means Of Transmission Electron Microscopy And Neutron Diffraction Techniques, Parikin Parikin, Mohammad Dani, Riza Iskandar, Aziz Khan Jahja, Andon Insani, Joachim Mayer

Makara Journal of Technology

The field of physical metallurgy is one of the primary beacons that guide alloy developments for multipurpose materials such as the in-core structure materials for pressure vessel components and heat exchangers. The surface microstructure of new ferritic steel with significant local constituent materials was characterized by high resolution powder neutron diffractometer (HRPD) and transmission electron microscope (TEM), combined with the energy dispersive X-ray spectroscopy (EDX). The alloy contains73% Fe, 24% Cr, 2% Si, 0.8% Mn, and 0.1% Ni, in %wt. The charge materials were melted by the casting techniques. The neutron diffractograms obtained shows five dominant diffraction peaks at (110), …

Study On Antibacterial Of Chitosan/Hydroxyapatite Doped Magnesium Composite As A Material For Bone Graft Applications, Andromeda Dwi Laksono, Teodoro A. Amatosa, Jr., Hilda Pebrianti Octaviana Sitorus, Wentika Putri Kusuma Asih, Sulistijono Sulistijono

Makara Journal of Technology

Hydroxyapatite (HAp) is one of the constituent minerals of bone and teeth, that has been widely used for synthesizing bone graft. Due to the limitation on properties of the hydroxyapatite, it is doping with Magnesium (HAp-Mg). The addition of Chitosan (Chi) was expected to improve the antibacterial properties of HAp-Mg. The present research aims to study the influence of Chitosan with 0, 5, 15, and 25 wt% addition on biocompatibility properties of Chi/HAp-Mg composite. HAp-Mg was synthesized using the sol-gel method; meanwhile, Chi/HAp-Mg composite was manufactured by mixing Chitosan in acetic acid, and HAp-Mg was added into the mixture. The …

Evaluation Of Primal-Dual Splitting Algorithm For Mri Reconstruction Using Spatio-Temporal Structure Tensor And L1-2 Norm, Mia Rizkinia, Masahiro Okuda

Makara Journal of Technology

Magnetic resonance imaging (MRI) is an essential medical imaging technique which is widely used for medical research and diagnosis. Dynamic MRI provides the observed object visualization through time and results in a spatiotemporal signal. The image sequences often contain redundant information in both spatial and temporal domains. To utilize this characteristic, we propose a spatio-temporal reconstruction approach based on compressive sensing theory. We apply spatio-temporal structure tensor using nuclear norm, in addition to the wavelet sparsity regularization. The spatio-temporal structure tensor is a matrix that consists of gradient components of the MRI data w.r.t the spatial and temporal domains. For …

Influence Of Nh4f In Dextran Based Biopolymer Electrolytes: Conductivity And Electrical Analysis, Muhamad Hafiz Hamsan, Mohd Fakhrul Zamani Kadir, Shujahadeen Bakar Aziz, Muhammad Amirul Solihin Azha, Saifful Kamaluddin Muzakir

Makara Journal of Technology

Dextran polymer host was doped with different concentrations of ammonium fluoride (NH4F) via casting technique. In this present work, dextran-NH4F film has been employed to investigate the ionic conductivity using electrochemical impedance spectroscopy from 50 to 5 MHz. The highest room temperature conductivity is achieved at (2.33 ± 0.76) × 10-3 S cm-1 with 40 wt.% NH4F. The electrolyte is found to obey Arrhenius rule at high temperature with activation energy of 0.21 eV. Dielectric analysis has been performed to obtain better understanding on the conductivity pattern. The dielectric parameters e.g. ɛreal, ɛimag, Mreal, and Mimag have been tested as …

Acute Toxicitystudy Of Choline Based Ionic Liquids Towards Danio Rerio Fish And The Aggregation Behavior Of Their Binary Mixtures, Mansoor Ul Hassan Shah, Nasruddin Nasruddin, Suzana Bt Yusup, Muhammad Moniruzzaman

Makara Journal of Technology

Marine oil spills are effectively controlled by chemical dispersants. However, the toxicity associated with it reduce its employment in marine environment. To overcome this limitation, the acute toxicity of choline based ionic liquids was evaluated as a potential low toxic variant for oil spill remediation. Further, the aggregation behavior of the individual as well as their binary mixtures was also evaluated by employing tensiometry technique. The half-lethal concentration, LC50on zebrafish (Danio rerio) of three choline based ionic liquids showed that the studied ionic liquids (ILs) fall in the range of “practically nontoxic” ( 100-1000 mg L-1).Various micellar properties showed that …

Neutron Diffraction Study Of Multiferroic 0.6nife2o4/0.4batio3 Composite, Engkir Sukirman, Yosef Sarwanto, Syahfandi Ahda, Andon Insani

Makara Journal of Technology

Neutron diffraction study on the 0.6NiFe2O4/0.4BaTiO3 multiferroic composite has been carried out. The 0.6NiFe2O4/0.4BaTiO3 multiferroic composites have been synthesized by solid reaction method. In this study, 20 g of BaTiO3 (BTO) and 20 g of NiFe2O4 (NFO) compounds were prepared from the powder raw materials of BaO3 and TiO2 for BTO, and NiO and Fe2O3 for NFO. Furthermore, both BTO and NFO were each crushed for 5 hours using High Energy Milling (HEM). Then the BTO and NFO were calcined in the furnace at 950 °C/5 hours and 900 °C/5 hours, respectively. Both NFO and BTO precursors were manually mixed …

Multiscale Modeling Of Fracture In Quasi-Brittle Materials Using Bifurcation Analysis And Element Elimination Method, Keyvan Zare Rami

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Analyzing the fracture of heterogeneous materials is a complex problem, due to the fact that the mechanical behavior of a heterogeneous material is strongly dependent on a variety of factors, such as its microstructure, the properties of each constituent, and interactions between them. Therefore, these factors must be effectively taken into account for accurate analysis, for which the multiscale method has been widely used. In this scheme, the computational homogenization method is used to obtain the effective macroscopic properties of a heterogeneous material based on the response of a Representative Volume Element (RVE). The growth of damage in an RVE …

Incorporating Geophysical Data In Slope Stability Modeling For Two Slopes In Arkansas, Vanessa Lebow

Graduate Theses and Dissertations

Slope failures in the United States alone cause millions of dollars in damage to infrastructure, threaten national monuments, create environmental hazards, and take an average of 25-50 lives a year. With the inevitable construction that occurs on slopes, it is imperative that the slopes be properly designed which requires a thorough understanding of slope grade, subsurface soil conditions, soil strength parameters, water table locations, and depth to bedrock across the entire site. The preferred method of data collection would be to use borings and other in-situ methods; however, sometimes due to cost constraints or site accessibility only a very limited …

Evaluation Of Concrete Deck Curing Regimens Using Capillary Pressure Sensing System, Samuel Spann

Graduate Theses and Dissertations

Early-age plastic shrinkage cracking is a common problem with the construction of concrete bridge decks due to the high surface area-to-volume ratio and exposure to potentially detrimental environmental effects. Curing regimens are utilized to mitigate cracking risk during the plastic stage of the concrete; the curing regimens evaluated for this study were wet burlap-polyethylene sheeting, two acrylic curing compounds, and one lithium compound. Capillary pressure in the water filled pores has been shown to correlate to the plastic shrinkage cracking risk of concrete. A new portable system has been developed to measure the capillary pressure that could potentially be used …

Truck Activity Pattern Classification Using Anonymous Mobile Sensor Data, Taslima Akter

Graduate Theses and Dissertations

To construct, operate, and maintain a transportation system that supports the efficient movement of freight, transportation agencies must understand economic drivers of freight flow. This is a challenge since freight movement data available to transportation agencies is typically void of commodity and industry information, factors that tie freight movements to underlying economic conditions. With recent advances in the resolution and availability of big data from Global Positioning Systems (GPS), it may be possible to fill this critical freight data gap. However, there is a need for methodological approaches to enable usage of this data for freight planning and operations.

To …

Study Of Internal Strains Developed In Concrete Decks At Early Ages In Steel Continuous Bridges, Fernando R. Benitez Ortiz

Graduate Theses and Dissertations

The Arkansas Department of Transportation (ARDOT) has identified bridge deck cracking shortly after concrete decks are placed and prior to applying traffic loads. Previous researchers have confirmed improper construction practices and design methods can lead to deck cracking. Currently, many contractors throughout Arkansas are using continuous deck pours. This construction approach may restrict the concrete slab from movement during early age shrinkage, causing tensile stresses to develop. The final stresses at the end of construction must be lower than the concrete tensile strength, if not cracking issues will develop. Eventually, these cracks may enlarge due to service load stresses and …

Cytotoxicity And Mutagenicity Of Disinfection Byproduct Mixtures Formulated Using Free Chlorine And Monochloramine, Yonas Ghebremedhin

Graduate Theses and Dissertations

Bioassays have been used extensively to assess various toxicity endpoints of drinking water disinfection byproducts (DBPs), but an emphasis on single compounds prevails. In this research, DBP mixtures were assessed using a cytotoxicity test with Chinese Hamster Ovary (CHO) cells and an Ames fluctuation test with Salmonella typhimurium TA-98 and TA-100 with and without S9 rat liver homogenate. Seven whole mixture DBP concentrates were formulated using reconstituted natural organic matter (NOM) extracts from the Upper Mississippi River using scaled disinfectant dosing protocols with free chlorine and monochloramine in the presence and absence of added bromide. DBPs were identified by gas …