Aerodynamics and Fluid Mechanics Commons^™

A Filter-Forcing Turbulence Model For Large Eddy Simulation Incorporating The Compressible "Poor Man's" Navier--Stokes Equations, Joshua Strodtbeck

Theses and Dissertations--Mechanical and Aerospace Engineering

A new approach to large-eddy simulation (LES) based on the use of explicit spatial filtering combined with backscatter forcing is presented. The forcing uses a discrete dynamical system (DDS) called the compressible ``poor man's'' Navier--Stokes (CPMNS) equations. This DDS is derived from the governing equations and is shown to exhibit good spectral and dynamical properties for use in a turbulence model. An overview and critique of existing turbulence theory and turbulence models is given. A comprehensive theoretical case is presented arguing that traditional LES equations contain unresolved scales in terms generally thought to be resolved, and that this can only …

Low Reynolds Number Flow Field Modification Via Travelling Wave Actuation Of A Vertically Aligned Wire Array Surface, John C. Calhoun

Theses and Dissertations--Mechanical and Aerospace Engineering

Experiments were conducted to observe the effects of an active wire surface on low-Reynolds number Poiseuille flow. The objective was to evaluate the feasibility of actuating piezoelectric nanowires into a travelling wave motion in order to reduce wall shear stress in turbulent flows. Studies have shown that travelling wave motions introduced into the bounding wall of turbulent flow can reduce wall shear stress by disrupting the formation of drag-inducing coherent vortical structures. A Reynolds number scaled flow facility was designed to represent the near-wall region of turbulent flow. A wire surface was installed in the bounding wall and dynamically actuated …

Aerodynamics And Control Of A Deployable Wing Uav For Autonomous Flight, Michael Thamann

Theses and Dissertations--Mechanical and Aerospace Engineering

UAV development and usage has increased dramatically in the last 15 years. In this time frame the potential has been realized for deployable UAVs to the extent that a new class of UAV was defined for these systems. Inflatable wing UAVs provide a unique solution for deployable UAVs because they are highly packable (some collapsing to 5-10% of their deployed volume) and have the potential for the incorporation of wing shaping. In this thesis, aerodynamic coefficients and aileron effectiveness were derived from the equations of motion of aircraft as necessary parameters for autonomous flight. A wind tunnel experiment was performed …

The Key Ideas Of Mdw Viii: A Summary, Aaron Altman, Clive L. Dym, Ray Hurwitz, John W. Wesner

Mechanical and Aerospace Engineering Faculty Publications

This paper summarizes and highlights the presentations and discussions that took place during Mudd Design Workshop VIII, ‘Design Education: Innovation and Entrepreneurship,’ at Harvey Mudd College. This paper also describes both the key ideas that emerged from the presentations and discussions of the participating engineering design educators, practitioners and researchers, and the methodology used to capture and retain those ideas. Additionally, this paper proposes a framework of design competencies that were created and evolved by the workshop’s participants as a response to a question posed at one of the workshop sessions: ‘What are the minimum design competencies students should learn …

Coupled Radiation-Gasdynamic Solution Method For Hypersonic Shock Layers In Thermochemical Nonequilibrium, Christopher L. Martin Jr.

Theses and Dissertations

The purpose of this research was to develop a highly accurate computational method for calculating the nonequilibrium radiative heat transfer within reentry shock layers. The nonequilibrium state of the flowfield was solved using the multispecies multitemperature nonequilibrium flow solver NH7AIR which is capable of separately tracking the vibrational energy of each diatomic species and the energy of the free electrons. The calculation of radiative heat transfer was performed by utilizing the detailed line-by-line spectral radiation solver SPRADIAN. Two radiative transport schemes were implemented in this coupled code. The first scheme was the standard tangent slab solution method. The second scheme …

Implementation And Validation Of The Ζ-F And Asbm Turbulence Models, Dustin Van Blaricom Quint

Master's Theses

The use of Computational Fluid Dynamics (CFD) tools throughout the engineering industry has become standard. Simulations are used during nearly all steps throughout the life cycle of products including design, production, and testing. Due to their wide range of use, industrial CFD codes are becoming more flexible and easier to use. These commercial codes require robustness, reliability, and efficiency. Consequently, linear eddy viscosity models (LEVM) are used to model turbulence for an increasing number of flow types. LEVM such as k-ε and k-ω provide modeling with little loss of computational efficiency and have proven to be robust. The LEVM that …

Development Of A Higher-Order Navier-Stokes Solver For Transient Compressible Flows, Arjun Vijayanarayanan

Doctoral Dissertations and Master's Theses

A higher‐order density based Navier‐Stokes solver was developed for 2‐Dimensional flows using the finite volume approach. The Van leer flux‐splitting technique was used to calculate the fluxes. The second‐order spatial accuracy was achieved using the variable extrapolation method developed by Van leer called the Montone Upstream Centered Scheme for Conservation Laws (MUSCL) approach. The code development was done using Matlab. The code was verified using two validation cases. Firstly, subsonic, transonic, and supersonic flows over the 2‐D bump were simulated, and the results of the code were compared to the results from Fluent. Secondly, the shock‐tube problem was chosen, and …

Numerical Analysis Of Gun Barrel Pressure Blast Using Dynamic Mesh Adaption, Sathish Xavier

Doctoral Dissertations and Master's Theses

A Computational Fluid Dynamics (CFD) method has been applied to simulate the pressure blast of the projectile which is launched from a barrel and to investigate the pressure distribution and sound pressure level (dB) along different positions away from the gun axis and towards the fuselage of the aircraft. Fluent was employed to simulate the unsteady flow using dynamic mesh with moving boundary. Most CFD based ballistics-model requires additional thermodynamic functions which must be derived from the Noble-Abel equation of state. The unsteady, axisymmetric Navier Stokes equation systems were numerically solved using the Advection Upstream Splitting Method (AUSM) scheme; with …

Designing Propulsion Systems For Future Aerospace Applications, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Flow Characteristics Of The Renovated Cal Poly 3 X 4 Ft Subsonic Wind Tunnel, Mathew L. Thomas, Dorian V. Pandey, Jason N. Nguyen

Aerospace Engineering

This paper investigates the flow characteristics of the renovated Cal Poly 3 x 4 ft subsonic wind tunnel. The IFA 300 constant-temperature anemometer along with a cross-plane X-wire dual-sensor probe was used to measure the mean velocity and turbulence intensity of the tunnel flow and part of the turbulent boundary layer at one section of the tunnel. Because of the malfunction of one channel of the IFA 300, only one wire of the dual sensor probe was calibrated for the measurements. The probe was then placed in a streamlined probe holder mounting on the traverse inside the wind tunnel. The …

Simulation Of Wing Tip Vortices, Ryan Termath, Jason Lechniak, Keerti Bhamidipati

STAR Program Research Presentations

Modeling and Simulation (M&S) computational fluid dynamics (CFD) techniques were used to better understand wing tip vortices about a wing section. The CFD results were compared to experimental wind tunnel data derived from the University of Iowa (Ref. 2). The experiment used Stereoscopic Particle Image Velocimetry (SPIV) to measure the flow field. The SPIV data from the experiment illustrates the vortex core development and behavior downstream of the trailing edge of the wing section. Three CFD simulations using various mesh sizes and time steps were completed and compared to the experimental results. Two dimensional plots of modeled local flow field …

Unsteady Total Pressure Measurement For Laminar-To-Turbulent Transition Detection, Akane Sharon Karasawa

Master's Theses

This thesis presents the use of an unsteady total pressure measurement to detect laminar-to-turbulent transition. A miniature dynamic pressure transducer, Kulite model XCS-062-5D, was utilized to measure the total pressure fluctuations, and was integrated with an autonomous boundary layer measurement device that can withstand flight test conditions. Various sensor-probe configurations of the Kulite pressure transducer were first examined in a wind tunnel with a 0.610 m (2.0 ft) square test section with a maximum operational velocity of 49.2 m/s (110 mph), corresponding dynamic pressure of 1.44 kPa (30 psf). The Kulite sensor was placed on an elliptical nose flat plate …

Boundary Layer Measurements Related To Wind Tunnel Testing Of Riblets, Emrah Cinar

Mechanical & Aerospace Engineering Theses & Dissertations

With fuel economy being a significant factor in today's world of aviation, aircraft manufacturers have been looking into ways to decrease drag to save fuel. Drag reduction using riblets on wing and fuselage surfaces is . an area that has been studied extensively for the last two decades. In preparation for a larger project which will use several methods to simulate this phenomena, small scale research had to be done to find ways to generate similar conditions on scaled models in a low speed wind tunnel and examine boundary layer behavior.

In this project, boundary layer measurement techniques, such as …

Design, Manufacturing And Testing Of An Environmentally-Green Bipropellant Thruster, Alex Bendoyro, Gabriel Sanchez, Erin Stearns, Phillip Takahashi

Aerospace Engineering

This project reviews the design, manufacturing and experimentation process of a green bi-propellant thruster designed to output 5 lbf. The goals were to successfully design, manufacture and test a thruster, while discovering the complications that arise through out the complete design process of a green thruster. The thruster was successfully designed using ideal rocket equations and the design was successfully confirmed using CFD and FEA. Manufacturing of the thruster was fully planned and revealed mild flaws in thruster design. For example some features were not manufacturable to the exact measurements desired. Testing of the engine gave results inconsistent with expected …

Numerical Modeling Of The Cn Spectral Emission Of The Stardust Re-Entry Vehicle, Alexandre Martin, Erin D. Farbar, Iain D. Boyd

Mechanical Engineering Faculty Publications

Re-entry vehicles designed for space exploration are usually equipped with thermal protection systems made of ablative material. In order to properly model and predict the aerothermal environment of the vehicle, it is imperative to account for the gases produced by ablation processes. In the case of charring ablators, where an inner resin is pyrolyzed at a relatively low temperature, the composition of the gas expelled into the boundary layer is complex and may lead to thermal chemical reactions that cannot be captured with simple ow chemistry models. In order to obtain better predictions, an appropriate gas ow chemistry model needs …

Human Powered Helicopter: Observing The Impacts Of Ground Effect And Intermeshed Rotors, Shane Stowe

Physics

No abstract provided.

Port Flow Test System, Daniel Chairez, Chelsea E. Crawford, Daniel S. Welch

Mechanical Engineering

Solar Turbines Gas Compressor Engineering Division of San Diego, California called upon the Mechanical Engineering students of California Polytechnic University, San Luis Obispo to provide recommendations for optimization of compressor end cap port design. Various sizes of compressors have end caps with numerous ports that exchange fluids between the inside and outside of the working fluid pressure vessel. Because so many ports must exist on the end caps, unusual flow paths are created to supply the appropriate location within the compressor. These flow paths commonly consist of a drilled inlet hole which intersects with a sudden expansion. The sudden expansion …

Rayleigh Test Apparatus Design Report, Josef Duller, Owen Raybould, James Nicovich

Mechanical Engineering

The Rayleigh Test Apparatus is a device that will be used to test the thermodynamic properties of Nitrous Oxide to assess the feasibility of using this fluid as a coolant for a hybrid rocket aero spike. The aero spike is intended to redirect the propulsion flow as it leaves the engine to create a more efficient flow pattern at low and high altitudes. However, there are issues of overheating which leads to melting of the aero spike. For this reason, the use of nitrous oxide (N2O) as a coolant is being explored. N20 is being considered because it is already …

Construction Of Naca 66-415 Nlf Composite Wing For Acoustic Turbulence Testing, Scott Sawyer, Sean Stewart

Aerospace Engineering

A design is developed for a Natural Laminar Flow (NLF) wing, to be used at California Polytechnic State University for acoustic turbulence testing. Composite materials are used to produce high-quality surface finishes necessary for laminar flow. A design for the test apparatus is presented and justified. A manufacturing procedure is proposed for the carbon fiber skin, using Vacuum Resin Infusion (VRI). This procedure is tested on a scaled part with satisfactory results; lessons learned are discovered and integrated into the final manufacturing process. The test section has been fit to the Cal Poly wind tunnel, but full implementation has not …

Designing The Human-Powered Helicopter: A New Perspective, Gregory Hamilton Gradwell

Master's Theses

The concept of human-powered vertical flight was studied in great depth. Through the manipulation of preexisting theory and analytical methods, a collection of design tools was created to expediently conceptualize and then analyze virtually any rotor. The tools were then arranged as part of a complete helicopter rotor design process. The lessons learned as a result of studying this process—and the tools of which it consists—are presented in the following discussion. It is the belief of the author that by utilizing these tools, as well as the suggestions that accompany them, future engineers may someday build a human-powered helicopter capable …