Energy Systems Commons^™

Performance Augmentation Of Single-Slope Solar Distiller Using An Evacuated Tube Solar Collector: Theoretical Study, Eman Mohammed Abuelezz Eng., Yasser El-Samadony Prof., Khaled Khodary Esmaeil Assoc. Prof., Mohamed Elsheshtawy Zayed Dr.

Journal of Engineering Research

In this research, the performance analysis of a solar-powered desalination system incorporating a single slope-slope solar still and an evacuated tube solar collector is theoretically investigated. The system comprises a solar evacuated tube that absorbs solar radiation, transferring heat to saline water. This water then flows into a solar still, where it absorbs solar energy, boosting the evaporation rate. Two solar distillers, namely the conventional solar distiller (Still-I) and solar still integrated with evacuated tube solar collector (Still-II), are simulated and analyzed under identical outdoor conditions in Tanta, Egypt. A comprehensive theoretical model, developed using FORTAN programming, simulates the performance …

Numerical Analysis Of Flow Fields For The Different Models Of The Shrouded Savonius Rotor, Alsaied Khalil Mahmoud, Mohamed Mahgoub Bassuoni, Mohamed Fawzy Obiaa, Ahmed Mostafa Khaira

Journal of Engineering Research

In this study, the effect of three different lengths (short, medium, and long) of flanged shrouded Savonius wind turbines is investigated three-dimensional (3-D) numerically by ANSYS-FLUENT. The 3-D numerical model of a simple rotor is validated by comparing the results with previous published experimental ones at the same operating conditions and geometry. The numerical and experimental results indicate a good agreement with each other when using the SST K-ω model with a time step size of 0.0025 s.The analysis of the numerical results of the three flanged shrouded models shows an enhancement of the torque coefficient at tip speed ratio …

Modeling Thermosyphon And Heat Pipe Performance For Mold Cooling Applications, Dwaipayan Sarkar

Electronic Thesis and Dissertation Repository

Thermosyphons are enhanced heat transfer devices that can continuously transfer very large amounts of heat rapidly over long distances with small temperature differences. The high heat transfer rate is achieved through simultaneous boiling and condensation of the working fluid and the continuous heat transfer is achieved through recirculation of the working fluid in its liquid and vapor phase. A potentially important application of the thermosyphons has been towards reducing the cycle times of the mold cooling processes which would provide economic incentives to the automotive industry.

Different operational and geometrical parameters such as the input heating power, fill ratio (FR), …

Enhancing The Performance Of Conventional Solar Still Using The Nano-Doped Paint (Ndp) Coating, Hagar Alm-Eldin Bastawissi Prof.Dr, Nermin Elgendy Engineer, Ayman R. El-Tohamy

Journal of Engineering Research

Nations are throughout the entire globe continuously confronting the problem of potable water shortage. Recently, it has been thought that using solar energy to desalinate brackish water offers a practical answer to the world's water crises. The output of these stills, is meager, and academics haven't done much to boost it in any way. Solar distillers have been proposed as an efficient method to produce potable water. In recent years, saltwater has produced drinking water by various ways. The efficiency of a solar distiller is significantly influenced by various factors, most important factor of them is the absorber surface. In …

Numerical Study Of The Effect Of Long Shroud Diffuser With And Without Plate Obstacle On The Performance Of Savonius Wind Turbine, Alsaied Khalil Mahmoud, Mohamed Mahgoub Bassuoni, Mohamed Fawzy Obiaa, Ahmed Mostafa Khaira

Journal of Engineering Research

This study presents the three-dimensional (3-D) numerical analysis of the influence of the plate obstacle installed at the entrance of the long flanged diffuser on the simple Savonius rotor performance by ANSYS 2022 R1. In the beginning, the 3-D numerical model is validated using the sst k-ω turbulence model with the previous published experimental results at the same conditions, and they are in good agreement with each other. The numerical results indicate the remarkable enhancement of the rotor performance at a tip speed ratio of 0 to 0.7 by using a flanged diffuser with a plate obstacle. The shrouded diffuser …

Data Driven And Machine Learning Based Modeling And Predictive Control Of Combustion At Reactivity Controlled Compression Ignition Engines, Behrouz Khoshbakht Irdmousa

Dissertations, Master's Theses and Master's Reports

Reactivity Controlled Compression Ignition (RCCI) engines operates has capacity to provide higher thermal efficiency, lower particular matter (PM), and lower oxides of nitrogen (NOx) emissions compared to conventional diesel combustion (CDC) operation. Achieving these benefits is difficult since real-time optimal control of RCCI engines is challenging during transient operation. To overcome these challenges, data-driven machine learning based control-oriented models are developed in this study. These models are developed based on Linear Parameter-Varying (LPV) modeling approach and input-output based Kernelized Canonical Correlation Analysis (KCCA) approach. The developed dynamic models are used to predict combustion timing (CA50), indicated mean effective pressure (IMEP), …

Depressurization Characteristics Of Steam-Based Reciprocating Vacuum Pump, Hongling Deng

Dissertations

This dissertation introduces a novel vacuum technology that leverages low-pressure saturated steam and cooling-controlled condensation, offering an efficient way to utilize low-grade thermal energy sources like waste heat, steam, or solar energy. At the heart of this technology is a unique duo-chamber vacuum pump system, featuring a reciprocating piston and a heat-conductive wall, designed to generate a vacuum through steam-condensation and cooling processes.

The core of this research lies in developing and validating mechanistic models for the steam-condensation depressurization process, a complex phenomenon involving phase change and transport mechanisms. Prior to this work, these mechanisms were not sufficiently modeled or …

Investigation Of Thermofluid Processes In A Pcm Based Thermal Storage Module, Luca M. Crnjac

Electronic Thesis and Dissertation Repository

Latent heat thermal energy storage systems can capture and store solar thermal energy, enhancing the reliability of solar energy by facilitating a continuous and consistent energy supply. However, phase change materials used in these systems suffer from low thermal conductivities making it difficult to achieve suitable charging and discharging rates. The present research investigated this issue using computational and experimental approaches to improve the design of a thermal storage module through heat transfer enhancement. Various heat transfer enhancements including a finned honeycomb structure, and metal wool were incorporated into a thermal storage module to analyze their effect on charging and …

Effects Of Back Reflectors And Thin Metal Covers On The Performance Of Near-Field Thermophotovoltaic Devices, Mehran Habibzadeh

Electronic Theses and Dissertations

Highly efficient energy harvesting devices that can recover a large amount of waste energy are of significant interest. Thermophotovoltaics (TPVs) are solid-state devices that can convert thermal energy radiated by a heated emitter into electrical power through the process of photovoltaic effect. In a TPV system, heat is converted to electricity by using a high-temperature emitter to radiate photons, which are then absorbed by a photovoltaic (PV) cell, generating electron-hole pairs and producing electrical power.

TPV devices have the advantages of producing High efficiency and being lightweight with low maintenance cost and zero pollution. However, these devices have not been …

Effect Of A Geothermal Heat Pump System On Cooling Residential Buildings In A Hot, Dry Climate, Rania Rushdy Moussa, Ayman H. Mahmoud

Architectural Engineering

ABSTRACT In the last century, electricity demand has doubled due to urban expansion, which has contributed to the formation of more urban heat islands (UHI) and the appearance of environmental hazards such as the global climate change phenomenon. Since residential buildings are considered the main electricity consumer sector in Egypt, they consume up to 42% of total energy consumption, which contributes to increasing temperatures and constitutes UHI in cities. In this context, the research aims to examine the effectiveness of using the closed vertical loop geothermal system (GSHPCV) for cooling residential buildings in a hot, dry climate, such as Cairo, …

Dynamics Modeling Of Molten Salt Reactors, Visura Umesh Pathirana

Doctoral Dissertations

The abundance of energy is a necessity for the prosperity of humans. The rise in energy demand has created energy shortages and issues related to energy security. Nuclear energy can produce vast amounts of reliable energy without many of the negative externalities associated with other competing energy sources, such as coal and natural gas. As a result, public interest in nuclear power has increased in the past decade. Many new types of nuclear reactor are proposed. These nuclear reactor designs feature many passive technologies that can operate without external influence. Reactors that feature advanced passive safety features are catagorized as …

Additively Manufactured Nature Inspired Morphology For Redesign: Advancing Next Generation Energy Systems, Vanshika Singh

Doctoral Dissertations

To meet cleaner energy goals and increasing demand, energy systems such as gas turbines and power plants are required to be operated under harsh loading conditions like higher temperatures and pressures, fluctuating loads, and corrosive environments. Advanced manufacturing techniques such as additive manufacturing (AM) have put us on the trajectory for next-generation system designs, allowing complex geometries and high-temperature alloys with tailored material properties. We need new and systematic design philosophies to use AM's unique characteristics prudently. For a given functionality, nature tends to provide similar solutions in animate and inanimate structures. We propose to take inspiration from nature's repetitive …

An Investigation Into Computational Modelling Of Melting And Solidification Of Phase Change Materials, Maryam Hemmat

Electronic Thesis and Dissertation Repository

This thesis evaluates the effectiveness of the enthalpy-porosity approach in simulating melting and solidification of phase change materials within latent heat thermal energy storage systems. It systematically investigates the sensitivity of the computational model to four adjustable parameters: mushy zone coefficient, thermal expansion coefficient, solidus/liquidus temperatures, and latent heat. The study includes individual and combined analyses of these factors in simulations of the melting process by comparing outcomes with extensive experimental data, resulting in a calibrated melting model. The calibrated model is validated across various heating conditions in the cylindrical cavity, and then in a rectangular cavity, confirming its reliability …

Onshore Power For The Docked Container Vessels In Apapa Port Through Blended Finance, Oladayo Matthew Atilola

World Maritime University Dissertations

No abstract provided.

Potential Roles Of Vessel Traffic Services (Vts) In Maritime Decarbonization, Suleiman Mustapha Bunza

World Maritime University Dissertations

No abstract provided.

Application Of Wind Propulsion In The Existing Fleet Of The Caspian Sea Using Real Wind Data, Mahmud Suleymanli

World Maritime University Dissertations

No abstract provided.

Analysis Of The Pros And Cons Of The Acquisition Of Training Ships By Metis, Jeremiah Yaw Frimpong

World Maritime University Dissertations

No abstract provided.

Exploring The Role Of Education In Addressing The Skills Gap For Seafarers In Bangladesh's Maritime Industry, Fatema Tuz Tahera

World Maritime University Dissertations

No abstract provided.

Design And Characterization Of A High Pressure Flow Loop For Heat Transfer Experiments Of Supercritical Carbon Dioxide, Joseph Sauerbrun

Doctoral Dissertations and Master's Theses

Supercritical carbon dioxide (sCO2) sees heightened heat transfer characteristics near its critical point due to its drastically changing thermophysical properties. Conventional single phase heat transfer theory was not developed to capture this nonlinear variation in properties and cannot predict the heat transfer characteristics of sCO2 to a practical level useful for design. To delve deeper into the behavior near the critical point and shed light on this crucial phenomenon, a state-of-the-art closed flow loop was developed. This setup enabled convective heat transfer experiments of sCO2 under diverse boundary conditions and test section geometries. Key components of the loop include the …

Investigation Of Solar Assisted Water Heating System Integrated With Pcm Storage Tank, Sohrab Saadat Pour

Major Papers

This study discusses the importance of integrating renewable energy sources, particularly Solar Water Heating Systems (SWHSs) with Thermal Energy Storage (TES) technology, to address the growing energy consumption in residential buildings, aligning with the United Nations' Sustainable Development 2030 agenda. The combination of SWHSs and TES helps reduce building energy consumption by storing excess solar energy, which can be used for Domestic Hot Water (DHW) needs during peak periods and nighttime. The study proposes a dynamic model using TRNSYS software to simulate a SWHS over a 30-hour period in a residential apartment. Additionally, a novel MATLAB component simulates an encapsulated …