Plasma and Beam Physics Commons^™

Simulation Of Neutron Generation From Laser-Driven Fusion In A Liquid D2o Sheet Using Novel Warpx Module, Colton R. Stoner

Theses and Dissertations

Using WarpX’s new nuclear fusion module, this work attempts to model an experimental system at the ELL at the AFIT with WarpX and draw conclusions about fusion products from resulting simulations. Recently, a table-top, high repetition rate, mixed radiation source was demonstrated at the ELL employing a HIL to fuse the deuterium nuclei present in a unique liquid target of heavy water. Analysis of the simulations predicted an isotropic output of neutrons from deuterium-deuterium fusion. These simulated neutrons were created in tens of femtoseconds from dense bodies of deuterons that were perturbed by the laser. However, it was found that …

Pulsed Power Neutron Production With Deuterated Polymer Accelerator Targets, Anthony O. Hagey

Theses and Dissertations

This document presents an investigation of the effect of deuterated polyethylene accelerator targets on the neutron fluence from a local mass injection dense plasma focus driven by the United States Naval Research Laboratory’s Hawk pulsed-power generator. After successful production of thin targets, the acquisition of thicker targets, and testing inside Hawk, it was found that the presence of a deuterated polyethylene target increased the neutron fluence. Results suggested that fluence can significantly increase with the presence of a deuterated target vs a nondeuterated target. Additive manufacturing printing was used as a production method in order to determine if deuterated accelerator …

On The Chronological Understanding Of The Homogeneous Dielectric Barrier Discharge, Xinpei Lu, Zhi Fang, Dong Dai, Tao Shao, Feng Liu, Cheng Zhang, Dawei Liu, Lanlan Nie, Chunqi Jiang

Bioelectrics Publications

Dielectric barrier discharges (DBD) are widely utilised non-equilibrium atmospheric pressure plasmas with a diverse range of applications, such as material processing, surface treatment, light sources, pollution control, and medicine. Over the course of several decades, extensive research has been dedicated to the generation of homogeneous DBD (H-DBD), focussing on understanding the transition from H-DBD to filamentary DBD and exploring strategies to create and sustain H-DBD. This paper first discusses the influence of various parameters on DBD, including gas flow, dielectric material, surface conductivity, and mesh electrode. Secondly, a chronological literature review is presented, highlighting the development of H-DBD and the …

A High-Precision Electron Emission Model: Computational Methods For Nanoscale Structures, Alister J. Tencate

Graduate Research Theses & Dissertations

The high-intensity, high-brightness and precision frontiers for charged particle beams are an increasingly important focus for study. Electron microscopy has demonstrated high quality beams from a single nanotip emitter, and cathodes of structured nanoscale arrays show promise as ultracold electron sources. Optimization of the cathode design for precision applications necessitates a detailed treatment of the interplay between the structure geometry, quantum mechanical emission mechanism, and electromagnetic interactions between the emitted electrons and the boundary interface. This dissertation details the numerical tools developed to simulate these processes efficiently with enough fidelity to be accurate even in the ultracold regime.

Conventional simulation …

Impulse Measurement Methods For Pulsed Laser Ablation Propulsion, Ishaan Mishra, Scott Kirkpatrick

Rose-Hulman Undergraduate Research Publications

Pulsed laser ablation propulsion has the potential to revolutionize space exploration by eliminating the requirement of a spacecraft to carry its propellant and power source as the high-power laser is situated off-board. More experimentation needs to be done to optimize this propulsion system and understand the mechanisms of thrust generation. There are many methods used to calculate the impulse imparted in pulsed laser ablation experiments. In this paper, key performance parameters are derived for some of the impulse measurement methods used in ablation propulsion experiments. Regimes discussed include the torsional pendulum system, simple pendulum system, and solid and liquid microspheres.

Arrayed Waveguide Lens For Beam Steering, Mostafa Honari-Latifpour, Ali Binaie, Mohammad Amin Eftekhar, Nicholas Madamopoulos, Mohammad-Ali Miri

Publications and Research

Integrated planar lenses are critical components for analog optical information processing that enable a wide range of applications including beam steering. Conventional planar lenses require gradient index control which makes their on-chip realization challenging. Here, we introduce a new approach for beam steering by designing an array of coupled waveguides with segmented tails that allow for simultaneously achieving planar lensing and off-chip radiation. The proposed arrayed waveguide lens is built on engineering the evanescent coupling between adjacent channels to realize a photonic lattice with an equi-distant ladder of propagation constants that emulates the continuous parabolic index profile. Through coupled-mode analysis …

Ultrashort Pulse Laser Filamentation Electrical And Optical Diagnostic Comparison, James E. Wymer

Optical Science and Engineering ETDs

Results presented here examine the effect of changing gas pressure on the radio frequency (RF) emissions of an ultrashort pulse laser filament plasma and how those emissions vary longitudinally in the laser focal region. We use a WR284 rectangular waveguide with a 1.5 cm hole that allows the beam through. A 3.2 GHz microwave signal is emitted in the waveguide, and signals are received through a waveguide-to-coax antenna connected to an HP8470B Schottky diode. By enabling and disabling the 3.2 GHz signal, we measure both the self-emitted RF from a USPL filament and subsequently the degree of attenuation a filament …

Design And Commissioning Of An E-Beam Irradiation Beamline At The Upgraded Injector Test Facility At Jefferson Lab, Xi Li, Helmut Baumgart, Charles Bott, Gianluigi Ciovati, Shaun Gregory, Fay Hannon, Mike Mccaughan, Robert Pearce, Matthew Poelker, Hannes Vennekate, Shaoheng Wang

Electrical & Computer Engineering Faculty Publications

The Upgraded Injector Test Facility (UITF) at Jefferson Lab is a continuous-wave superconducting linear accelerator capable of providing an electron beam with energy up to 10 MeV. A beamline for electron-beam irradiation has been designed, installed and successfully commissioned at this facility, aimed at the degradation study of 1,4-dioxane and per- and polyfluoroalkyl substances (PFAS) in wastewater treatment. A solenoid with a peak axial magnetic field of up to 0.28 T and a set of raster coils were used to obtain a Gaussian beam profile with a transverse standard deviation of ∼15.0 mm at the target location. Monte-Carlo simulations using …

Artificial Intelligence, Controls, And Sensor Fusion For Optimization And Modeling Of Space Missions And Particle Accelerators, Reza Pirayeshshirazinezhad

Mechanical Engineering ETDs

This PhD dissertation is devoted to developing artificial intelligence (AI) applications for space missions and particle accelerators considering constraints on the computational resources. The space mission studied in this research, the Virtual Telescope for X-ray Observations (VTXO), is the mission exploiting 2 6U-CubeSats operating in a precision formation. The goal of the VTXO project is to develop a space-based, X-ray imaging telescope with high angular resolution precision. VTXO space mission is designed and the mission is optimized to increase the performance of the mission. Trajectory optimization with AI, hybrid control, control algorithms, and high performance computing are all used to …

Foundations Of Plasmas For Medical Applications, T. Von Woedtke, Mounir Laroussi, M. Gherardi

Electrical & Computer Engineering Faculty Publications

Plasma medicine refers to the application of nonequilibrium plasmas at approximately body temperature, for therapeutic purposes. Nonequilibrium plasmas are weakly ionized gases which contain charged and neutral species and electric fields, and emit radiation, particularly in the visible and ultraviolet range. Medically-relevant cold atmospheric pressure plasma (CAP) sources and devices are usually dielectric barrier discharges and nonequilibrium atmospheric pressure plasma jets. Plasma diagnostic methods and modelling approaches are used to characterize the densities and fluxes of active plasma species and their interaction with surrounding matter. In addition to the direct application of plasma onto living tissue, the treatment of liquids …

Pseudo-Modal Expansions For Generating Random Electromagnetic Beams, Milo W. Hyde Iv, Olga Korotkova

Faculty Publications

Excerpt: We derive two pseudo-modal expansions that provide insight into the structure of stationary electromagnetic sources and can be used for their physical realization and in computer simulations. Both expansions are derived from the vectorial version of Bochner’s theorem of functional analysis.

Grand Challenges In Low Temperature Plasmas, Xinpei Lu, Peter J. Bruggeman, Stephan Reuter, George Naidis, Annemie Bogaerts, Mounir Laroussi, Michael Keidar, Eric Robert, Jean-Michel Pouvesle, Dawei Liu, Kostya (Ken) Ostrikov

Electrical & Computer Engineering Faculty Publications

Low temperature plasmas (LTPs) enable to create a highly reactive environment at near ambient temperatures due to the energetic electrons with typical kinetic energies in the range of 1 to 10 eV (1 eV = 11600K), which are being used in applications ranging from plasma etching of electronic chips and additive manufacturing to plasma-assisted combustion. LTPs are at the core of many advanced technologies. Without LTPs, many of the conveniences of modern society would simply not exist. New applications of LTPs are continuously being proposed. Researchers are facing many grand challenges before these new applications can be translated to practice. …

Beamline For E-Beam Processing At Uitf, G. Ciovati, C. Bott, S. Gregory, F. Hannon, Xi Li, M. Mccaughan, R. Pearce, M. Poelker, H. Vennekate

Electrical & Computer Engineering Faculty Publications

No abstract provided.

Numerical Investigations Of 2-D Magnetic Nozzles On Pulsed Plasma Plumes, Joshua Daniel Burch

Masters Theses

"This research presents studies of a novel type of magnetic nozzle that allows for three-dimensional (3-D) steering of a plasma plume. Numerical simulations were performed using Tech-X's USim® software to quantify the nozzle's capabilities. A2-D planar magnetic nozzle was applied to plumes of a nominal pulsed inductive plasma (PIP) source with discharge parameters similar to those of Missouri S&T's Missouri Plasmoid Experiment (MPX). Argon and xenon plumes were considered. Simulations were verified and validated through a mesh convergence study as well as comparison with available experimental data. Periodicity was achieved over the simulation run time and phase angle samples were …

Improvements To Emissive Plume And Shock Wave Diagnostics And Interpretation During Pulsed Laser Ablation Of Graphite, Timothy I. Calver

Theses and Dissertations

This dissertation covers nanosecond pulsed laser ablation of graphite for 4-5.7 J/cm² fluences with 248 nm and 532 nm lasers in 1-180 Torr helium, argon, nitrogen, air, and mixed gas. Three experiments were performed to improve the interpretation of common diagnostics used to characterize pulsed laser ablation, find simple but universal scaling relationships for comparing dynamics across different materials and ablation conditions, and provide a systematic analysis of graphite emissive plume and shock wave dynamics. A scaling of the Sedov-Taylor energy ratio was developed and validated for a range of studies despite differences in wavelength, pulse duration, fluence, and …

One Dimensional Study Of Magnetoplasmadynamic Thrusters For A Potential New Class Of Heavy Ion Drivers For Plasma Jet Driven Magnetoinertial Fusion, Patrick M. Brown

Theses and Dissertations

Plasma Jet Driven Magnetoinertial Fusion (PJMIF) requires high velocity heavy ion drivers in order to compress a magnetized target to fusion conditions. Previous work with heavy ion drivers has revealed sub-par accelerations due to plasma instabilities; thus, it is necessary to investigate new methods of heavy ion plasma acceleration. One such method is Magnetoplasmadynamic (MPD) thrusters. Past studies of these thrusters have been conducted at an initial temperature at or below the energy of full ionization. Here MPD thrusters are investigated using a Godunov type MHD solver with a Harten-Lax van Leer-D (HLLD) flux solving scheme assuming the plasma is …

Plasma Aerodynamics: Experimental Quantification Of The Lift Force Generated On An Airfoil Using Plasma Actuation To Estimate Power Requirements In Small Uav Applications, Getachew Ashenafi

UNLV Theses, Dissertations, Professional Papers, and Capstones

This research addressed the amount of electric power required to induce specific changes in lift force using a NACA 2127 airfoil with a chord length of ~28 mm, connected to a micro load cell, in a wind tunnel of 103 square centimeter cross-section. A DBD plasma actuator supplied by a ZVS driven high voltage pulsed DC circuit, operating at a frequency of 17.4 kHz, was utilized for voltages of up to 5000 V. Two configurations of electrode gapping were compared to determine the efficient use of power. The configuration with a gap of ~1 mm between the upstream and downstream …

On The Dynamic Generation Of Megagauss-Level Magnetic Fields On 100-Ns Timescales To Stabilize And Magnetize Pulsed-Power-Driven Liner Implosions, Gabriel A. Shipley

Electrical and Computer Engineering ETDs

This dissertation presents analysis of experiments and simulations executed to develop the auto-magnetizing liner concept (AutoMag) for use as an alternative premagnetization mechanism for MagLIF. Tests of each stage of AutoMag (magnetization, dielectric breakdown, and implosion) were executed on the Mykonos accelerator and the Z accelerator. Experiments demonstrate strong peak axial magnetic field production (20 – 150 T), dielectric breakdown initiation that depends on global induced electric field across the target, and a level of cylindrical implosion uniformity high enough to be useful for prospective fusion-fuel-filled (auto-magnetized MagLIF) experiments.

This dissertation also presents detailed simulations of the Solid Liner Dynamic …

Impendance Probe Payload Development For Space-Based Joint Service Collaboration, Brian T. Kay

Theses and Dissertations

Collaborations utilizing small spacecraft in near earth orbit between the U. S. Coast Guard Academy (CGA), Naval Research Lab (NRL), the U. S. Naval Academy (USNA), and the Air Force Institute of Technology (AFIT) have initiated scientific and engineering space-based experiments. Sourced opportunities like the VaSpace ThinSat missions have provided a platform for payload, sensor, and experiment development that would have otherwise been resource prohibitive. We have constructed an impedance probe payload derived from the existing ‘Space PlasmA Diagnostic suitE’ (SPADE) mission operating from NASA’s International Space Station. Currently both space and laboratory plasmas are investigated with AC impedance measurements …

Design Of A 10 Mev Beamline At The Upgraded Injector Test Facility For E-Beam Irradiation, Xi Li, Helmut Baumgart, Gianluigi Ciovati, F.E. Hannon, S. Wang

Electrical & Computer Engineering Faculty Publications

Electron beam irradiation near 10 MeV is suitable for wastewater treatment. The Upgraded Injector Test Facility (UITF) at Jefferson Lab is a CW superconducting linear accelerator capable of providing an electron beam of energy up to 10 MeV and up to 100 µA current. This contribution presents the beam transport simulations for a beamline to be used for the irradiation of wastewater samples at the UITF. The simulations were done using the code General Particle Tracer with the goal of obtaining an 8 MeV electron beam of radius (3-σ) of ~2.4 cm. The achieved energy spread is ~74.5 keV. The …

Reflection And Transmission Of Electromagnetic Pulses At A Planar Dielectric Interface: Theory And Quantum Lattice Simulations, Abhay K. Ram, George Vahala, Linda Vahala, Min Soe

Electrical & Computer Engineering Faculty Publications

There is considerable interest in the application of quantum information science to advance computations in plasma physics. A particular point of curiosity is whether it is possible to take advantage of quantum computers to speed up numerical simulations relative to conventional computers. Many of the topics in fusion plasma physics are classical in nature. In order to implement them on quantum computers, it will require couching a classical problem in the language of quantum mechanics. Electromagnetic waves are routinely used in fusion experiments to heat a plasma or to generate currents in the plasma. The propagation of electromagnetic waves is …

Simulation Studies On The Interactions Of Electron Beam With Wastewater, X. Li, S. Wang, Helmut Baumgart, G. Ciovati, F. Hannon

Electrical & Computer Engineering Faculty Publications

The manufactured chemical pollutants, like 1,4 dioxane and PFAS (per- and polyfluroralkyl substances), found in the underground water and/or drinking water are challenging to be removed or biodegraded. Energetic electrons are capable of mediating and removing them. This paper utilizes FLUKA code to evaluate the beam-wastewater interaction effects with different energy, space and divergence distributions of the electron beam. With 8 MeV average energy, the electron beam exits from a 0.0127 cm thick titanium window, travels through a 4.3 cm distance air and a second 0.0127 cm thick stainless water container window with 2.43 cm radius, and finally is injected …

Equations Of State For Warm Dense Carbon From Quantum Espresso, Derek J. Schauss

Theses and Dissertations

Warm dense plasma is the matter that exists, roughly, in the range of 10,000 to 10,000,000 Kelvin and has solid-like densities, typically between 0.1 and 10 grams per centimeter. Warm dense fluids like hydrogen, helium, and carbon are believed to make up the interiors of many planets, white dwarfs, and other stars in our universe. The existence of warm dense matter (WDM) on Earth, however, is very rare, as it can only be created with high-energy sources like a nuclear explosion. In such an event, theoretical and computational models that accurately predict the response of certain materials are thus very …

Transient Behavior Of Drift And Ionization In Atmospheric Pressure Nitrogen Discharge, S. K. Dhali

Electrical & Computer Engineering Faculty Publications

The fluid models are frequently used to describe a non-thermal plasma such as a streamer discharge. The required electron transport data and rate coefficients for the fluid model are parametrized using the local field approximation (LFA) in first order models and the local-mean-energy approximation (LMEA) in second order models. We performed Monte Carlo simulations in Nitrogen gas with step changes in the E/N (reduced electric field) to study the behavior of the transport properties in the transient phase. During the transient phase of the simulation, we extract the instantaneous electron mean energy, which is different from the steady state mean …

The Resistive Barrier Discharge: A Brief Review Of The Device And Its Biomedical Applications, Mounir Laroussi

Electrical & Computer Engineering Faculty Publications

This paper reviews the principles behind the design and operation of the resistive barrier discharge, a low temperature plasma source that operates at atmospheric pressure. One of the advantages of this plasma source is that it can be operated using either DC or AC high voltages. Plasma generated by the resistive barrier discharge has been used to efficiently inactivate pathogenic microorganisms and to destroy cancer cells. These biomedical applications of low temperature plasma are of great interest because in recent times bacteria developed increased resistance to antibiotics and because present cancer therapies often are accompanied by serious side effects. Low …

High Voltage Design And Evaluation Of Wien Filters For The Cebaf 200 Kev Injector Upgrade, Gabriel Palacios-Serrano, Helmut Baumgart, C. Hernández-García, P. Adderley, J. Benesch, D. Bullard, J. Grames, A. Hofler, D. Machie, M. Poelker, M. Stutzman, R. Suleiman

Electrical & Computer Engineering Faculty Publications

High-energy nuclear physics experiments at the Jefferson Lab Continuous Electron Beam Accelerator Facility (CEBAF) require highly spin-polarization electron beams, produced from strained super-lattice GaAs photocathodes, activated to negative electron affinity in a photogun operating at 130 kV dc. A pair of Wien filter spin rotators in the injector defines the orientation of the electron beam polarization at the end station target. An upgrade of the CEBAF injector to better support the upcoming MOLLER experiment requires increasing the electron beam energy to 200 keV, to reduce unwanted helicity correlated intensity and position systematics and provide precise control of the polarization orientation. …

Applications Of Cathodoluminescence In Plasmonic Nanostructures And Ultrathin Inas Quantum Layers, Qigeng Yan

Graduate Theses and Dissertations

Due to the advanced focusing ability, characterization methods based on the electron-beam excitation have been broadly applied to investigate nanomaterials. Structural or compositional information is commonly acquired using electron microscopes. Moreover, taking advantage of the super spatial resolution of the focused electron beam, optical properties of nanomaterials can be also obtained. Herein, general concepts and processes of the interaction between electrons and materials are studied. Two specific optical nanomaterials, including plasmonic nanostructures and semiconductor quantum layers, are investigated by the cathodoluminescence (CL) measurement.

Surface plasmonic resonance can be generated when high-energy electrons strike the interface between the dielectric medium and …

Impacts Of Laboratory Vibrations And Laser Flicker Noise On Digital Holography, Douglas E. Thornton, Mark F. Spencer, Christopher A. Rice, Glen P. Perram

Faculty Publications

In this paper, we experimentally demonstrate the impacts of laboratory vibrations and laser flicker noise on digital holography (DH). Specifically, we measure both the vibration efficiency and the coherence efficiency of our DH system at various focal-plane array integration times and path-length differences between the signal and reference. These efficiencies, in practice, contribute to the overall mixing efficiency, which is a measure for how well the detected signal and reference interfere. The results show that when the integration time is ≤1ms, the laboratory vibrations are negligible with a vibration efficiency of 100%; however, when the integration time equals 100 ms, …

Growth Of Small Particles In Nonequilibrium Plasmas, Necip Berker Üner

McKelvey School of Engineering Graduate Student Theses & Dissertations

Nonequilibrium plasma (NEP) is an extraordinary environment for material synthesis. NEP is comprised of hot electrons with temperatures greater than 10000 K and of cold ions and neutrals that are usually at few hundred kelvins above room temperature. Due to this large difference in species’ temperatures, the assumption of local thermal equilibrium does not hold in NEP. Therefore, NEP can act as a unique processor of mass, and it can transform materials along pathways that are not accessible by methods wherein local thermal equilibrium is valid. For decades, NEPs have been employed in the semiconductor industry to manufacture many thin …

Optimizing Llrf Parameters In The Electron-Ion Collider, William M. Bjorndahl

Physics

To improve particle interaction in the future Electron-Ion Collider (EIC), we investigated different feedback implementations to control the accelerating voltage and examined the power and beam phase for each instance. Using MATLAB, we studied three feedback mechanisms: Direct, One Turn, and Feedforward. Enacting feedforward yielded the best performance. To minimize the klystron power consumption, we analyzed different Low-Level Radio Frequency (LLRF) parameters such as detuning. Combining theory and simulated results, we found the optimal detuning value that minimizes klystron power consumption.