Plasma and Beam Physics Commons^™

String-Of-Pearls Measurements Of Supersonic Plasma Jets Using Magnetospheric Multiscale Satellites, Amelia Koth

Discovery Day - Daytona Beach

High-energy supersonic plasma jets form when the solar wind, which is a flow of charged particles from the Sun, slows down as it encounters Earth’s magnetic shield. Occasionally, the solar wind remains at supersonic speeds as it enters this region. This forms plasma jets that propagate toward Earth; these jets can carry strong magnetic fields, drive magnetic reconnection, and potentially initiate substorms that lead to auroral activity.   Previously studied plasma jets occurred when the interplanetary magnetic field (IMF) points southward. In contrast, this study focuses on northward IMF conditions, which are less understood, yet still capable of producing supersonic jets. …

Multi-Dimensional Particle-In-Cell With Monte Carlo Collisions (Pic-Mcc) Simulation For Visualizing Plasma Flow And Secondary Ionization In Constricted-Anode Geometries, Parth Thakar

Discovery Day - Daytona Beach

Constricted-anode plasma sources generate locally intensified electric fields that enhance ionization near the anode, making them valuable in propulsion and laboratory plasma systems. However, the narrow geometry produces complex charge accumulation and secondary ionization effects that remain difficult to measure experimentally. To address this challenge, our research develops and applies a multi-dimensional Particle-in-Cell with Monte Carlo Collisions (PIC-MCC) simulation of a DC discharge in 1-D, 2-D, and 3-D configurations that model a constricted-anode device. PIC-MCC is a first-principles method that tracks electrons and ions individually while computing self-consistent electric fields and incorporating energy-dependent collision processes. This approach enables direct visualization …

Effect Of Anode Size On The Properties Of Constricted Hollow Anode Pulsed Plasma Source, Nirav Patel, Garret Seckinger

Discovery Day - Daytona Beach

With the advent of ion thrusters, burns requiring large velocity changes can be performed with a fraction of the propellant required by traditional chemical rocket engines. However, current ion thrusters produce thrust in the order of millinewtons and thus cannot be viable for launching vehicles or burns requiring velocity changes in a small amount of time. Furthermore, current ion thrusters experience grid and component erosion, where the two grids at the termination of the nozzle slowly erode due to particle impact, and the hot electrodes degrade due to high thermal load. This limits the life of ion engines, which require …

A Feedback Loop Control To Automate Cold Atmospheric Pressure Plasma Based Additive Manufacturing, Arineh Shahbazi

Discovery Day - Daytona Beach

Currently, nanoparticle annealing based additive manufacturing process requires high temperatures, making them unsuitable for a broad range of applications. By lowering the temperature and developing a process to use Cold Atmospheric Pressure Plasma (CAPP) for annealing, many more doors are opened to a wide range of materials, films, and environments for space, communication, and microelectronics. CAPP-based additive manufacturing technology is continually evolving, making projects like nanoparticle annealing more feasible. In this work, we designed a CAPP jet printer assembly consisting of a 0.25-inch outer diameter glass tube connected to a 3D printing nozzle. The flow of Argon gas in the …

Experimental Investigation Of The Discharge Modes Of Nanosecond Pulsed Plasmas At Atmospheric Pressure, Md Ziaur Rahman

Electrical & Computer Engineering Theses & Dissertations

The generation of repeatable and stable nanosecond pulsed atmospheric pressure plasmas is important to non-thermal plasma applications in various fields including medicine, material processing, food processing, and plasma ignition for combustion. This dissertation investigates the atmospheric pressure plasma initiation and formation under 10 – 200 ns pulsed power for electrode configurations applicable for transient plasma ignition (TPI) for combustion. The impacts of pulsed power parameters, gas condition, and electrode geometry on the discharge initiation and modes (i.e., streamer, transient spark and spark) are systematically evaluated for applying TPI for combustion. We evaluated the discharge modes driven by both longer and …

Simulations Of Atmospheric Pressure Streamer Discharges: Mechanisms Of Streamer Propagation And Related Physics, Dejan Nikic

Electrical and Computer Engineering ETDs

Gas discharge simulations are performed with particular focus on photoionization process in a positive streamer discharge. The effects of this process are investigated by isolating the change in photoionization mean free path (MFP) and keeping the additional processes constant. Furthermore, comparison are made between various effects of simulation parameters, such as initial conditions, geometry extent, simula- tion particle count etc. All of these simulations are performed using a modern Direct Simulation Monte Carlo Particle-in-Cell (DSMC-PIC) code developed by Sandia Na- tional Laboratories. Large scale simulations including 1 cm and 5 cm electrode gaps are performed under standard atmospheric condition air. …

Measurements And Scaling Of Ion Propulsion Impulse During Driven Magnetic Reconnection, Fatima Ebrahimi, Nicholas A. O'Gorman, Kush Maheshwari, Jongsoo Yoo, Alexandre Sainterme, Hantao Ji

Faculty Publications

Impulse scaling during magnetic reconnection, the magnetic energy conversion to kinetic energy, via direct Mach probe measurements in Magnetic Reconnection Experiment is examined. Ion exhaust velocity and impulse scalings with reconnecting magnetic field during the push phase of driven reconnection are presented. The outflows and impulse measurements are compared with global MHD simulations. Both measurements and simulations reveal a favorable scaling, greater than linear, of impulse with reconnecting field. These scaling results establish that magnetic reconnection could be utilized for plasma propulsion.

Determining The Electric Field In A 10 Ns Pulsed Plasma In Fuel-Air Mixtures Using Efish, Md Ziaur Rahman, Christopher J. Kliewer, Brian D. Patterson, Chunqi Jiang

Bioelectrics Publications

Transient plasma ignition (TPI) utilizes non-equilibrium plasmas, produced by nanosecond high-voltage pulses, to improve lean-fuel combustion performance and reduce emission. It is known that the relatively high reduced electric field (E/N) in TPI plays an important role in generating energetic electrons and facilitating energy-efficient radical productions, resulting in reliable ignition for lean combustion. Determining the reduced electric field in the discharge is hence important for the understanding of the TPI process and ultimately allowing for the control of the plasma chemistry. This study reports spatiotemporally resolved measurements of the electric field (E) in a 10 ns pulsed plasma that is …

Low Energy Ion Irradiation Effects In Electronic Devices And Materials, David C. Mccall

All Dissertations

The physics and engineering of ion-solid interactions are governed by the ion beam characteristics (flux, charge, energy) and target(s) in question. Here I present work on two projects related to the extraction of a high flux of low charge state Argon ions from a commercial plasma source and the irradiation of an engineered target, a transistor, with high charge state Argon ions.

An end-Hall ion source that produces a a high current plasma of ions and electrons in a rough vacuum environment is characterized. Using a Langmuir probe and multiple pressure measurements, the ion and electron content of the source …

Phase Nanoscopy With Correlated Frequency Combs, Xiaobing Zhu

Optical Science and Engineering ETDs

In this dissertation a sensing method applying to any physical quantity that modifies optical phase is developed. Two pulses are produced inside a synchronously pumped Optical Parametric Oscillator, generating two identical, undistinguishable frequency combs. The physical quantity to be measured applies a small phase shift/round trip to one of the pulses, resulting in a frequency shift of the corresponding comb. The latter frequency is measured as a beat by interfering the two combs on a detector. A world record resolution, close to the quantum limit, of 0.033 nanoradian (corresponding to 0.006 fm in displacement) is achieved. A detailed analysis of …

Development Of A Near Terahertz Backward Wave Oscillator Using Standard Waveguide, Alexander Glick

Electrical and Computer Engineering ETDs

There is a demand for terahertz (THz) frequency radiation sources. Applications include, but are not limited to, imaging for medical and security purposes, biochemical and organic spectroscopy, and velocimetry. Historically, there was a limited supply of THz devices due to technological limitations. In recent years much progress has been made to reduce this “gap” in supply and demand for THz sources. This work proposes a vacuum electronic device that produces high power, extremely high frequency radiation in the G-band, by utilizing a backward wave oscillator (BWO) based on WR3 standard waveguide. This device is compact, fundamentally simple, and has great …

Characterization Of A Magnetically Contained Hot Filament Plasma Source With A Wide-Sweeping Langmuir Probe, Jonas Rowan

Doctoral Dissertations and Master's Theses

Ionospheric plasma research in the Space and Atmospheric Instrumentation Laboratory’s Space Plasma Chamber has been hindered by the lack of a suitable plasma diagnostic instrument and understanding of its hot-filament plasma source. This thesis describes efforts made to remedy both problems. A wide-range Sweeping Langmuir Probe was developed with a ±35 V sweeping range to fully analyze ion and electron saturation regions in the entire IV curve. A method was derived to estimate the chamber source’s filament temperatures. The new Langmuir probe was integrated into a refurbished automated system designed in Python to measure plasma parameters for various chamber conditions, …

Power-Beaming: Wireless Energy Transfer Using Lasers, Spencer L. Barnett

ATU Scholars Symposium

The objective of the project is to implement a wireless energy transfer system utilizing laser technology. This system involves modulating the laser’s beam profile and spatial distribution through precise optical manipulation. The energy transmitted by the laser is captured by a photovoltaic array, commonly referred to as a solar panel, which is engineered to convert incident photons into direct current (DC) electrical power. The current challenge is to develop a reliable wireless energy transfer mechanism capable of operating over extended distances, thereby overcoming the constraints imposed by wired connections, particularly in environments where wiring is impractical, such as in space. …

Developing Fixed-Bias Langmuir Probes For Multi-Point Constellation Deployments, Henry Carter Valentine

Doctoral Dissertations and Master's Theses

Since their initial development in the early 20th century, electrostatic Langmuir probes have proved invaluable in terrestrial and interplanetary ionospheric sounding applications. When deployed aboard rocket and satellite platforms, these probes yield high-cadence, in-situ measurements of key plasma parameters such as electron density, ion density, and electron temperature. Furthermore, the efficacy of Langmuir probes in characterizing the three-dimensional structure and dynamics of ionospheric plasmas can be augmented by the technique of multi-payload deployments. In this work, we discuss the design, development, and analysis of fixed-bias Langmuir probes constructed for two multi-point science campaigns: the Mars-bound, dual-satellite Escape and Plasma Acceleration …

Streamer Discharge Simulation For Plasma-Assisted Combustion, Stuart Jairo Reyes

Electrical & Computer Engineering Theses & Dissertations

A common and successful method to achieve atmospheric pressure fuel-air plasma-assisted combustion is through repetitive ns pulsed discharges and dielectric-barrier discharge. The transient phase in these discharges is dominated by transport influenced by strong space charges produced by ionization fronts, this can be best represented by the streamer model. The function of non-thermal plasma in these discharges is to excite the species in the fuel-air mixture to produce radicals which accelerate the chemical conversion reactions which directly lead to temperature rise, ultimately culminating in ignition. Therefore, the characterization of the streamer and its energy partitioning is essential to developing a …

Determining The Transient Electric Field And The Effect Of Pulse Repetition Frequency On The Field In A Repetitive 10-Ns Pulsed Discharge In A Quiescent Ch₄-Air Mixture, Chunqi Jiang

Bioelectrics Publications

The goal of this research is to understand the underlying physics enabled by nanosecond pulsed power in a discharge initiation and the following physicochemical processes that favor lean-fuel plasma ignition for combustion. The hypothesis of this project is that pulsed power waveforms such as the pulse repetition frequency (PRF), voltage amplitude, and dielectric surface alter the reduced electric field during the initiation of the discharge, resulting in different plasma properties, which will vary the physicochemical processes for efficient and selective radical productions. This is especially important for lean-burn combustion and reducing emission.

Outgassing Measurements Of Bare And Magnetite-Coated Low-Carbon Steel Vacuum Chambers, Aiman H. Al-Allaq, Md Abdullah Mamun, Matt Poelker, Abdelmageed Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

The outgassing properties of bare and magnetite-coated AISI 1020 low-carbon steel vacuum chambers were evaluated to establish material selection criteria for extreme high vacuum applications, namely, to explore the possibility of using these materials to build next-generation spin-polarized photoelectron guns. Water outgassing measurements using the throughput method revealed that the magnetite-coated chamber exhibited five times lower outgassing at room temperature prior to baking, but this advantage disappears after 80 °C baking. Hydrogen outgassing measurements demonstrated significant differences after intensive heat treatment: the bare low-carbon steel vacuum chamber achieved a specific outgassing rate of 9.6 × 10⁻¹⁶ Torr L s …

The Effect Of Electrode Geometry On Excited Species Production In Atmospheric Pressure Air-Hydrogen Streamer Discharge, Shirshak Kumar Dhali, Stuart Reyes

Electrical & Computer Engineering Faculty Publications

When a gas is overvolted at or near atmospheric pressure, it results in a streamer discharge formation. Electrode geometries exert significant impact on the electrical breakdown of gases by altering the spatial profile of the electric field. In many applications the efficient generation of radicals is critical and is determined by the characteristics of the streamer discharge. We examine the effect of electrode geometry on the streamer characteristics and the production of radicals. This is performed for three different electrode geometries: plane–plane, pin–plane, and pin–pin. A two-dimensional rotationally symmetric fluid model is used for the streamer discharge simulation in the …

Polarized Photocathode R&D At Bnl And Spin Consideration For The Eic Preinjector, Jyoti Biswas, Erdong Wang, Omer Rahman, John Skaritka, Adam Masters, Sylvain Marsillac, Tai-De Li

Electrical & Computer Engineering Faculty Publications

Superlattice GaAs photocathodes are vital for producing polarized electron beams for the Electron-Ion Collider (EIC) at Brookhaven National Laboratory. The electron pre-injector at the EIC requires a 7 nC bunch with at least 85% spin polarization from a GaAs-based superlattice cathode. The doping density of the very surface layer of the cathode needs to be optimized to extract a high bunch charge beam from the high-voltage DC gun. The polarization axis of the emitted beam is longitudinal, and it will be rotated to transverse direction using two Wien filters, each rotating the spin by 45 degrees. In this paper, we …

Streamer Discharge Modeling For Plasma-Assisted Combustion, Stuart Reyes, Shirshak Kumar Dhali

Electrical & Computer Engineering Faculty Publications

Some of the popular and successful atmospheric pressure fuel/air plasma-assisted combustion methods use repetitive ns pulsed discharges and dielectric-barrier discharges. The transient phase in such discharges is dominated by transport under strong space charge from ionization fronts, which is best characterized by the streamer model. The role of the nonthermal plasma in such discharges is to produce radicals, which accelerates the chemical conversion reaction leading to temperature rise and ignition. Therefore, the characterization of the streamer and its energy partitioning is essential to develop a predictive model. We examine the important characteristics of streamers that influence combustion and develop some …

Optical Investigation Of A Low-Pressure Plasma In A Superconducting Radio-Frequency Cavity, Zachary A. Caudell

Electrical & Computer Engineering Theses & Dissertations

The state-of-the-art cryomodules for particle accelerators use superconducting radio-frequency (SRF) cavities. It is known that accumulation of hydrocarbon impurities reduces the cavity surface work function, decreasing cryomodule performance metrics such as field emission, thermal stability, and accelerating gradients. An in-situ method of plasma processing has recently been developed to clean the cavities and restore cryomodule performance [1]. This study is to understand the properties of the low-pressure plasmas generated in a C100 SRF cavity and ultimately to improve the performance of plasma surface cleaning using optical emission spectroscopy. Using a 500 mm focal length Czerny-Turner monochromator coupled with a photomultiplier …

Generation And Implementation Of Mixed Radiation From Laser Interactions On A Liquid Target, Benjamin M. Knight

Theses and Dissertations

The simultaneous generation of different forms of radiation from the same source is highly desirable but technically challenging. We present the generation of D-D fusion neutrons and >MeV-energy x-rays from extreme intensity (∼ 10¹⁹ W/cm² ), high repetition-rate (1 kHz) laser pulses on a thin liquid target. Total neutron fluxes of ∼ 105 neutrons/s and x-ray exposure rates up to ∼ 200 R/hr at 74 cm are measured. Evidence of D-D fusion is verified with a measurement suite including three independent neutron detection systems: an EJ-309 organic scintillator, a ³He proportional counter, and a set of 36 …

Surface Patterning On Zirconia Dental Implants Via Laser-Induced Shockwave Imprinting, Inomjon Majidov

Masters Theses & Specialist Projects

Zirconia is rapidly becoming a preferred alternative to titanium in dental applications, primarily due to its aesthetic resemblance to natural teeth. This material’s tooth-like color avoids the aesthetic issues associated with the grey metal tint of titanium implants. Additionally, zirconia is hypoallergenic, making it an ideal choice for patients with metal sensitivities or allergies. Despite these advantages, zirconia generally exhibits lower biocompatibility and osseointegration compared to titanium implants. This study investigates laser-assisted, controlled imprinting technique on zirconia surfaces to enhance these properties. Our research used zirconia pellets, produced from powdered monoclinic zirconia pressed in a pellet press machine. Two methods …

Redirection Of Current In A Dense Plasma Focus, Rocky Gonzalez

UNLV Theses, Dissertations, Professional Papers, and Capstones

The Mission Support & Test Services (MSTS) reports that significant amounts of energy needed for generating high energy neutrons is lost within a Dense Plasma Focus between its pinch-end of the anode stalk and at its base near the insulating sleeve. It is their mission and the goal of this research effort to both experimentally and theoretically study current redirection in a DPF during and after pinch dynamics. It is hypothesized that current redirection, due to restrike, behind the dynamic sheath of a dense plasma focus will result in a measurable change in the magnetic field along the longitudinal axis …

Plasma Diagnostics For Anode Cathode Plasmas And High Energy Density Physics On A Linear Transformer Driver, Robert Beattie-Rossberg

Electrical and Computer Engineering ETDs

A twelve-brick air insulated linear transformer driver (LTD) was characterized by charging to voltages ranging from 30 to 70 kV and delivering energy to two separate resistive loads. Various plasma diagnostics were built and fielded with an emphasis on the design, implementation and analysis of a Mach Zehnder interferometer, a moiré deflectometer and a spectroscopy system providing information on the temporal evolution of plasma electron density and atomic composition. Rogowski coils, XRD radiation detectors, framing camera images and time integrated DSLR images are used to further understand load conditions where current data, x ray radiation data, velocity data and instability …

Pulsed-Power Neutron Production With Deuterated Polymer Accelerator Targets, Anthony O. Hagey, Juan J. Manfredi, Whitman T. Dailey, S. L. Jackson, E. R. Kaiser, J, W. Schumer

Faculty Publications

This document presents an investigation of the effect of deuterated accelerator targets on the neutron fluence from a local mass injection dense plasma focus (LMIDPF) driven by the United States Naval Research Laboratory's (NRL) Hawk pulsed-power generator. Deuterated targets were made using two methods: a well-established thin-film casting technique for flat targets and a more novel additive manufacturing technique that allowed targets to be three-dimensional (3D) printed in both flat and conical geometries. These targets were then tested during neutron-producing experiments conducted using Hawk, and theneutron fluences measured for the various target types were compared. Additive manufacturing was used as …

Spectroscopic Characterization Of Trivalent Holmium In Liyf4 And Bay2F8 Crystals, Vivian R. Hedberg

Theses and Dissertations

Yttrium-fluoride crystals doped with trivalent holmium are promising laser gain media for mid-infrared laser systems. To accurately model laser systems, a complete optical characterization of the laser gain medium is required. The key modeling parameters were obtained by a spectroscopic investigation of Ho³⁺ in LiYF₄ and BaY₂F₈ crystal hosts. Several important mid-infrared laser transitions were characterized at nominal Ho³⁺ ion concentrations of 10-30 at.%. Polarized emission cross-sections were determined from the fluorescence spectra using the Füchtbauer-Ladenburg method. Polarized absorption cross-sections were obtained using the Integral Reciprocity method. The upper-state lifetimes were measured at room …

Parametrization Of Fluid Models For Electrical Breakdown Of Nitrogen At Atmospheric Pressure, Shirshak K. Dhali

Electrical & Computer Engineering Faculty Publications

In the transient phase of an atmospheric pressure discharge, the avalanche turns into a streamer discharge with time. Hydrodynamic fluid models are frequently used to describe the formation and propagation of streamers, where charge particle transport is dominated by the creation of space charge. The required electron transport data and rate coefficients for the fluid model are parameterized using the local mean energy approximation (LMEA) and the local field approximation (LFA). In atmospheric pressure applications, the excited species produced in the electrical discharge determine the subsequent conversion chemistry. We performed the fluid model simulation of streamers in nitrogen gas at …

The Discharge-Induced Polarity-Dependent Propagation Characteristics Of A Strong Shock Wave, Anna Markhotok

Physics Faculty Publications

The specifics of a shock wave propagation down a positive column of a DC discharge in molecular chemically inert gases has been investigated. It was shown that axial gradients caused by the imbalance in the charged particle momentum transfer to the gas molecules can be a reason for the shock velocity dependence on the electric field direction. In pure nitrogen gas, the calculated shock velocity difference of up to 13.5% is in good agreement with the 12% value obtained in the experiment. A returning gas flow organizing in the discharge as a possible mechanism for an extended shock structure and …

Adaptive Plasmonic Metasurfaces For Radiative Cooling And Passive Thermoregulation, Azadeh Didari-Bader, Nooshin M. Estakhri, Nasim Mohammadi Estrakhri

Engineering Faculty Articles and Research

In this work, we investigate a class of planar photonic structures operating as passive thermoregulators. The radiative cooling process is adjusted through the incorporation of a phase change material (Vanadium Dioxide, VO₂) in conjunction with a layer of transparent conductive oxide (Aluminum-doped Zinc Oxide, AZO). VO₂ is known to undergo a phase transition from the “dielectric” phase to the “plasmonic” or “metallic” phase at a critical temperature close to 68°C. In addition, AZO shows plasmonic properties at the long-wave infrared spectrum, which, combined with VO₂, provides a rich platform to achieve low reflections across the …