Polymer Chemistry Commons^™

Thiophene Derivative Monomers Co-Electropolymerized On Microelectrodes Within Arrays For Tailored Surface Chemistry And Electrochemical Properties, Benjamin J. Jones

Graduate Theses and Dissertations

Potentiodynamic co-electropolymerization of two thiophene derivatives, (2,3-dihydrothieno[3,4-b]dioxin-2-yl)methanol (1) and 4-((2,3-dihydrothieno[3,4-b][1,4]dioxin-2-yl)-methoxy)-4-oxobutanoic acid (2), in aqueous solutions (0.02 M total monomer, 0.05 M sodium dodecyl sulfate (SDS) and 0.1 M LiClO4) on gold microband electrodes in an array was investigated. A modified Steglich esterification reaction between monomer 1 and succinic anhydride produced monomer 2 at 93.6% yield. Seven deposition solutions of the two monomers, defined by mol% of monomer 2 (0, 25, 34, 50, 66, 75, 100) generated seven sets of polymer films by cyclic voltammetry in a specially designed cell to conserve monomer. The onset potential for monomer oxidation and total …

Effect Of Post-Consumer Content And Bioplastic Incorporation On Polymeric Resin In Consumer Applications, Shelby Bicknell

Electronic Theses & Dissertations

Controversy surrounds the use of plastic products, primarily due to their potentially negative impact on the environment at the end of their lifecycle. The most widely used plastics are manufactured from petrochemicals such as petroleum, coal or natural gas. Petrochemical plastics are not able to readily breakdown in the environment, which aggravates the existing pollution problems. Fortunately, there are eco-friendly alternatives to petrochemical-based plastics. Bioplastics may be derived from renewable sources, biodegradable, or both. Bio-based plastics are plastics that may be derived from renewable biomass sources including, but not limited to, vegetable oils, cornstarch, straw, woodchips, and food waste. They …

Fabrication Of Polymer Monoliths Within The Confines Of Non-Transparent 3d-Printed Polymer Housings, Noor Abdulhussain, Suhas H. Nawada, Sinéad Currivan, Marta Passamonti, Peter J. Schoenmakers

Articles

In the last decade, 3D-printing has emerged as a promising enabling technology in the field of analytical chemistry. Fused-deposition modelling (FDM) is a popular, low-cost and widely accessible technique. In this study, RPLC separations are achieved by in-situ fabrication of porous polymer monoliths, directly within the 3D-printed channels. Thermal polymerization was employed for the fabrication of monolithic columns in optically non-transparent column housings, 3D-printed using two different polypropylene materials. Both acrylate-based and polystyrene-based monoliths were created. Two approaches were used for monolith fabrication, viz. (i) in standard polypropylene (PP) a two-step process was developed, with a radical initiated wall-modification step …

The Synthesis Of A Mepeg-Based Hydroxide Conducting Electrolyte And The Optimization Of The Mepeg-Tosylation Reaction, Andrew Ladner

Honors Theses

As society is becoming increasingly aware of the effects of climate change and the ever-looming threat of a fuel shortage, exploring green and renewable alternative energy production, such as fuel cells, is paramount. This project investigates the synthesis of a polyethylene glycol monomethyl ether (MePEG_n) based polymer as well as the optimization of the MePEG Tosylation reaction. The MePEG explored contains seven polymerized ethoxy groups (MePEG₇). The MePEG₇ polymer was modified by substituting a positively-charged trimethylamine group in the place of the alcohol functional group at the end of the PEG chain. The reason for …

Hypervalent Iodine Compounds With Carboxylate And Tetrazolate Ligands, Avichal Vaish

Chemistry Theses and Dissertations

In modern organic chemistry, hypervalent (HV) iodine(III) compounds are frequently used as oxidizing agents but application of λ³-iodanes in polymer and material chemistry is still underexplored. This dissertation describes the preparation of dynamic and self-healing materials by employing ligand exchange reactions involving HV iodine(III) compounds of the type ArIL₂ (Ar = Aryl, L = ligand, e.g., carboxylate or (pseudo)halide). These compounds can undergo ligand exchange reactions in presence of nucleophiles (Nu^-) to form ArINu₂. Diacetoxyiodo benzene was successfully employed as a crosslinker to prepare dynamic and self-healing gels derived from carboxylate-containing polymers. Furthermore, …

Modification And Optimization Of Conducting Polymer-Modified, Redox-Magnetohydrodynamics (R-Mhd) Pumping For Enhanced And Sustained Microfluidics Applications, Md Foysal Zahid Khan

Graduate Theses and Dissertations

In this work, a novel microfluidic pumping approach, redox-magnetohydrodynamics (R-MHD) has improved by materials and device optimization to use in lab-on-a-chip applications. In R-MHD, magnetic flux (B) and ionic current density (j) interacts to generate body force (FB) in between active electrodes, according to the equation FB = j×B. This unique fluid pumping approach is scalable, tunable, generates flat flow profile, and does not require any channels or valves. Pumping performance, such as speed scales with the ionic current density (j) and duration depends on the total charge (Q). The ionic current density (j) results from the conversion of electronic …

Voc Emission Factors From 3d Printers - Abs (Acrylonitrile-Butadiene-Styrene) Type Filaments, Dean Lay

LSU Master's Theses

Acrylonitrile-butadiene-styrene (ABS) is a polymer that is widely used in many plastic products and is receiving new attention due to its use as a filament for fused deposition modelling (FDM) 3D printers. It has been shown to emit potentially dangerous volatile organic compounds (VOCs) when heated at temperatures used in the 3D printing process. Many new products are becoming available that contain various additives to the polymer matrix, which have an unknown effect on the emission profiles and rates. In this study a method is developed using a modified system for thermal diagnostic studies (STDS) to evaluate VOC emission from …

Properties And Applications Of Tetraalkylphosphonium Alkylsulfate Ionic Liquids And 3d Printed Polymerized Ionic Liquids, Mustafa Mohammed Alhussain

Murray State Theses and Dissertations

Ionic liquids (ILs) are defined as pure salts with a melting temperature below 100 °C with a subset called room-temperature ILs (RTILs) with melting temperatures at or below room temperature. The sizes of the cation and anion play a critical role in determining the properties, with smaller ions forming stronger ionic forces and packing better, raising viscosity and lowering conductivity of the IL. At the same time, intermolecular forces such as van der Waals and hydrogen bonding can play a role in IL properties as well. Our research described herein is focused on three tetraalkylphosphonium-based cations coupled with three alkylsulfate …

Increased Utility Of Ph Sensitive Indicators As High Concentration Co2 Detectors Through The Use Of Polyelectrolyte Complexes As Stabilizing Media, Camden James Johnson

All Master's Theses

Development of plastic materials which produce visible color change when exposed to different environments has recently attracted attention for many biomedical applications.^1,2Many biomedical devices are packaged under high concentrations of carbon dioxide (CO₂) which can lower the pH of the packaging environment. This is similar to the CO₂ chemistry responsible for ocean acidification.³ Dye molecules that are sensitive to environmental changes in pH (known as pH indicators) can be encapsulated in plastics and produce a visible color change when a medical device is removed from the sterile CO₂ environment. Plastics made from large …

Multidimensional Mass Spectrometry Of Chemonic™ Ccg-6 Nonionic Surfactant With Separation By Polarity And Shape, Charles Johnson

Williams Honors College, Honors Research Projects

Chemonic™ CCG-6 surfactant is a water-soluble poly(ethylene glycol) (PEG) conjugated alkyl glyceride emollient. This surfactant exists as a complex mixture of a glycerol cores conjugated with poly(ethylene glycol) branches (PEGylation) that were partially esterified with caprylic (C8) and capric (C10) acids. These may be esterified on one, two, or all three arms of the glyceride. The architecture of the structures in this mixture was studied using multidimensional mass spectrometry (MS). Mass spectrometry was interfaced with ultra-performance liquid chromatography (UPLC) and ion mobility (IM) separation. The mixture was separated by reversed-phase LC, oligomers of the star-branched polymer were separated according to …

Stabilized, Hybrid Solid-State Photocatalysts For Water Purification: Preparation, Properties And Performance Under Visible Light Irradiation, Karpagavalli Ramji

Seton Hall University Dissertations and Theses (ETDs)

Stabilized heterogeneous photocatalysts that use only solar light and air have been prepared and successfully employed to decontaminate water from organic pollutants. Organic dye pollutants present, for example in textile effluents, are one of the major sources of water pollution owing to their limited biodegradability, toxicity and potential carcinogenic risks. Before certifying water for public consumption, reuse in industries or for discharge in surface water the organic pollutants must be degraded, an effort that is energy intensive and currently requires complex methodologies. We report solid-state photocatalysts that use only visible light and air to treat wastewater. Perfluoroalkyl perfluoro-substituted zinc phthalocyanine …

Electropolymerization Of Polyaniline In The Presence Of Ferricyanide: Electrochemical, Spectroscopic And Gravimetric Studies, Lucas Marinelli

Master's Theses

In this work, ferricyanide-doped polyaniline (PANI) is electropolymerized by constant current and cyclic voltammetry (CV) measurements with simultaneous monitoring of mass changes using electrochemical quartz crystal microbalance (eQCM). Raman spectroscopy, Fourier transform infrared spectroscopy and CV measurements confirm the incorporation of the ferricyanide into the film and indicate modified electrical conductivity. UV-Vis absorbance spectroscopy and Raman spectroscopy confirm the conducting ‘emeraldine-salt’ state and confirm the presence of polarons, i.e. charge carriers.

The addition of ferricyanide during electropolymerization of the PANI film results in an increase of polymerization rate as confirmed using eQCM. A decrease in counter ion ingress/egress and an …

Characterization Of Coacervate Systems Using Redox Sensitive Dyes, Caleb Kaiser

All Master's Theses

Coacervates are systems that spontaneously form when two oppositely charged polyelectrolytes are mixed in a concentrated salt solution. When coacervates form, a biphasic equilibrium occurs in the sample with two phases present in the solution. The two phases are described as the dense phase and the lean phase, named after the amount of polyelectrolyte material in each phase. Coacervates have been topics of interest to researchers in a variety of fields including biomedical applications, drug delivery devices, and more. This thesis worked towards the characterization of coacervate systems on the molecular level by investigating the interaction of the polyelectrolytes and …

Enhanced Analysis Of Lignin Dehydrogenation Oligomers Via Mass Spectrometry, Amber Suzanne Bowman

Theses and Dissertations--Chemistry

Effective analytical techniques need to be developed to characterize the products of lignin degradation experiments to be able to generate renewable products from lignin. Mass spectrometry is an valuable analytical approach for lignin characterizaion, but it is hindered by lignin’s poor ionization efficiency, especially in the positive ion mode. In this work, we attempt to improve lignin’s ionization by utilizing electrospray and laser desorption mass spectrometry coupled with the addition of cations and chemical derivatives. We confronted the ionization problem from both a top-down and bottom-up analytical approach by analyzing synthesized monomers, dimers, and polymers along with natural lignin extracts …

A Quartz Crystal Microbalance Study Of Thiol:Ene Poly(Ionic Liquid) Polymerization And Gas Absorption, Yueming Wu

Murray State Theses and Dissertations

ABSTRACT

The polymerization process of, and gas absorption by, imidazolium-containing thiol:ene poly (ionic liquid)s (PILs), prepared from bisallylimidazolium bis(trifluoromethyl sulfonyl)imide [NTf₂^-] and pentaerythritoltetrakis(3 mercaptopropionate), was studied. The thiol:ene PILs examined were recently reported by groups at Murray State University. The advantage of thiol:ene PILs over other reported PILs is that thiol:ene polymers are made rapidly by UV exposure and exhibit high mechanical and thermal stability due to high cross-linking. The properties of interest for the thiol:ene PILs were studied using a quartz crystal microbalance (QCM). QCM techniques are based on the piezoelectric effect, where certain crystals (e.g., …

Nitric Oxide Release From Poly(Lactic-Co-Glycolic Acid) Nanoparticles And Titanium Alloy, Nina A. Reger

Electronic Theses and Dissertations

Current methods for the treatment of bacterial infection involve the use of systemic antibiotics, which are high concentrations of antibiotics delivered over a long period time. Unfortunately, the use of systemic antibiotics can cause harmful side effects to the patient and increases the possibility for antibiotic resistance. The delivery of antibiotics or alternative antimicrobial compounds, such as nitric oxide, directly to the site of infection would decrease the amount of antibiotic necessary to treat a bacterial infection.

Poly (lactic-co-glycolic acid)/polyvinyl alcohol nanoparticles and a titanium- aluminum-vanadium metal oxide alloy implant were surface functionalized to deliver nitric oxide. Polymer nanoparticles can …

Micro-Spectroscopy Of Bio-Assemblies At The Single Cell Level, Jeslin Kera

Honors Undergraduate Theses

In this thesis, we investigate biological molecules on a micron scale in the ultraviolet spectral region through the non-destructive confocal absorption microscopy. The setup involves a combination of confocal microscope with a UV light excitation beam to measure the optical absorption spectra with spatial resolution of 1.4 μm in the lateral and 3.6 μm in the axial direction. Confocal absorption microscopy has the benefits of requiring no labels and only low light intensity for excitation while providing a strong signal from the contrast generated by the attenuation of propagating light due to absorption. This enables spatially resolved measurements of single …

Synthesis And Development Of Zwitterionic Pei (Zpei) For Optimized Delivery Of Nucleic Acids, Joseph Raleigh Duke Iii

Theses and Dissertations--Chemistry

Gene therapy holds promise for the treatment a wide range of diseases ranging from cystic fibrosis to cardiovascular disease to cancer. The need for safe and efficient gene delivery methods remains the primary barrier to human gene therapy. Non-viral vector materials, including polymers, can be designed to be biocompatible and non-immunogenic, but lack the efficiency to be clinically relevant. Gene therapy awaits the development of new materials that are both safe and efficient. Here, we have synthesized a series of modified zwitterionic polymers based on the common transfecting agent polyethylenimine (PEI). Using a variety of biochemical and biophysical methods we …

Direct Attachment Of 4-Hydroxybenzoic Acid Polymers And Capture Agents To Flat Sheet And Microdialysis Membranes For Improved Mass Transport, Sarah Jane Phillips

Graduate Theses and Dissertations

Microdialysis (MD) sampling is a diffusion-based separation method which has the ability to sample any analyte that can diffuse across the semi-permeable membrane. However one challenge for MD is that for soluble proteins greater than 10 kDa, the relative recovery (RR) using a 100 kDa MD probe is between 1-5%.1 There are two major barriers that lead to these low recovery values - nonspecific adsorption (NSA) and poor solute mass transport. To overcome these two barriers, the modification of PES-based MD membranes has been initiated by laccase. Previous researchers have used laccase to modify PES flat sheet and hollow fiber …

A Comparison Of Solvent And Water-Borne Alkyd Coatings And The History Of Voc Regulations In The United States, Molly Elise Burns

Master's Theses

A Comparison of Solvent and Water-Borne Alkyd Coatings Abstract

Conventional solvent based alkyd coatings have gone out of favor due to concerns over volatile organic compound (VOC) content. However, due to recent focus on renewable raw materials, alkyds are making a comeback in waterborne form. Water based alkyd coatings are known to have poor shelf stability and corrosion resistance, as well as other problems during the formulation process. This project focused on comparing solvent borne to two types of water-borne alkyds, water reducible alkyds and alkyds emulsions. The purpose was to understand the differences between the three types of alkyds …

An Investigation Into The Use Of Polymer Bound Boronic Acid For Glucose Detection In Paper Based Microfluidic Devices, Spencer A. Schultz

Master's Theses

Paper Based Microfluidic Devices (microPADs) are a new platform for point-of-care diagnostic assays for use in resource-limited settings. These devices rely typically on enzymatic assays to produce their results, which makes them susceptible to degradation when exposed to extreme environmental conditions such as high temperature. In order to overcome this limitation, this research project focused on investigating the use of polymers instead of enzymes to detect analytes on microPADs.

Polymer-bound boronic acid, a glucose and pH sensitive polymer, was incorporated into microPADs in order to develop a chronometric, paper-based glucose assay. The polymer was tested with both lateral and vertical …

Development And Characterization Of Reagent Pencils For Microfluidic Paper Based Analytical Devices, Cheyenne H. Liu

Master's Theses

Microfluidic paper based analytical devices (microPADs) are a novel platform for point of care (POC) diagnostics. Limitations of reagent shelf life have been overcome with the introduction of reagent pencils as a method for solid-based reagent deposition. While useful, little work has been reported on the characterization and optimization of reagent pencils. Herein, an investigation on reagent pencil composition and efficiency is conducted via colorimetric release profile tests utilizing an erioglaucine disodium salt that yields a quantifiable blue colored product in the presence of water. Within this work, an investigation on the molecular weight dependence, polymer chain end functionality, and …

Quantifying The Use Of Chloroform Vapor Exposure To Improve The Adhesion Of Au Thin Films Onto Pmma, Kathleen T. Krist

Senior Honors Projects, 2010-2019

The metallization of Au onto plastics is an important processing step in applications such as the aerospace and automotive industries, the field of microelectronics, and the fabrication of microfluidic devices. While its corrosion resistance and excellent electrical and thermal conductivity make Au a useful choice, its inertness results in poor adhesion to polymer surfaces. Previous studies have indicated that exposing commercially available poly(methyl methacrylate) (PMMA) sheets to chloroform vapor following Au deposition significantly improves adhesion. In this study, we utilized electron-beam evaporation and magnetron sputtering to deposit Au thin films onto 1.50 mm thick PMMA and exposed the samples to …

Curing Of Polymer Thermosets Via Click Reactions, Mark Richard Brei

Dissertations

In the first project, an azide functional resin and tetra propargyl aromatic diamines were fabricated for use as a composite matrix. These systems take already established epoxy/amine matrices and functionalize them with click moieties. This allows lower temperatures to be used in the production of a thermoset part. These new systems yield many better mechanical properties than their epoxy/amine derivatives, but their T_gs are low in comparison.

The second project investigates the characterization of a linear system based off of the above azide functional resin and a difunctional alkyne. Through selectively choosing catalyst the linear system can show …

Fabrication Of Multifunctional Nanostructured Porous Materials, Ahmed A. Farghaly

Theses and Dissertations

Nanostructured porous materials generally, and nanoporous noble metals specifically, have received considerable attention due to their superior chemical and physical properties over nanoparticles and bulk counterparts. This dissertation work aims to develop well-established strategies for the preparation of multifunctional nanostructured porous materials based on the combination of inorganic-chemistry, organic-chemistry and electrochemistry. The preparation strategies involved one or more of the following processes: sol-gel synthesis, co-electrodeposition, metal ions reduction, electropolymerization and dealloying or chemical etching. The study did not stop at the preparation limits but extended to investigate the reaction mechanism behind the formation of these multifunctional nanoporous structures in order …

Green Chemistry As A Tool For Understanding The Toxic Substances Control Act: A Lecture Module For Undergraduate Students, Molly R. Blessing

Honors Scholar Theses

The Toxic Substances Control Act (TSCA) is the central form of chemical regulation existent in the United States today, yet scientists are often unaware or uncertain of its provisions. Violations of TSCA by unknowing chemists set industry and government unnecessarily at odds. A lecture on TSCA was developed for undergraduate students that uses the concept of green chemistry to promote interest and incentivize learning. Green chemistry methods are cleaner and less wasteful than traditional chemical ones, and many companies using them are at the forefront of technological innovation. The lecture explains both green chemistry and TSCA, includes company case studies, …

Inhalable Nanocomposites And Anticancer Agents For Cancer Therapy, Nathanael A. Stocke

Theses and Dissertations--Chemical and Materials Engineering

Cancer is designated as the leading cause of mortality worldwide and lung cancer is responsible for nearly 30% of all cancer related deaths. Over the last few decades mortality rates have only marginally increased and rates of recurrence remain high. These factors, among others, suggest the need for more innovative treatment modalities in lung cancer therapy. Targeted pulmonary delivery is well established for treating pulmonary diseases such as asthma and provides a promising platform for lung cancer therapy. Increasing local deposition of anticancer agents (ACAs) and reducing systemic exposure of these toxic moieties could lead to better therapeutic outcomes and …

Characterization Of Noncovalent Complexes Of Polyelectrolytes By Mass Spectrometry, Anthony J. Marino

Williams Honors College, Honors Research Projects

Various ions of poly-L-lysine and polystyrene sulfonic acid were successfully observed first within a matrix-assisted laser desorption/ionization mass spectrometer and subsequently in an electrospray ionization mass spectrometer. The successful ionization of these polymers allowed for studies to be performed on the noncovalent interactions between the two. Noncovalent interactions were effectively studied on both instruments, but further quantified using tandem mass spectrometry found within the MALDI system and ion-mobility mass spectrometry found within the electrospray ionization system. As a result of employing the use of ion-mobility, various different stoichiometries and charges of polyelectrolyte complexes could be distinguished.

Synthesis And Applications Of Mutimodal Hybrid Albumin Nanoparticles For Chemotherapeutic Drug Delivery And Phototherml Therapy Platforms, Donna V. Peralta

LSU New Orleans Theses and Dissertations

Progress has been made in using human serum albumin nanoparticles (HSAPs) as carrier systems for targeted treatment of cancer. Human serum albumin (HSA), the most abundant human blood protein, can form HSAPs via a desolvation and crosslinking method, with the size of the HSAPs having crucial importance for drug loading and in vivo performance. Gold nanoparticles have also gained medicinal attention due to their ability to absorb near-infrared (NIR) light. These relatively non-toxic particles offer combinational therapy via imaging and photothermal therapy (PPTT) capabilities.

A desolvation and crosslinking approach was employed to encapsulate gold nanoparticles (AuNPs), hollow gold nanoshells (AuNSs), …

Modified-Electrodes For Redox-Magnetohydrodynamic (Mhd) Pumping For Microfluidic Applications, Christena Kayl Nash

Graduate Theses and Dissertations

A new microfluidic pumping and stirring technique was demonstrated for lab-on-a-chip applications. Microfluidics was accomplished via redox-MHD, which takes advantage of a body force (F_B) that is generated when there is a net movement of ions in solution (j) in the presence of a perpendicular magnetic field (B), according to the equation F_B = j×B. In this work the movement of ions in solution was generated using electrodes modified with the conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT) rather than a redox species in solution, which can interfere with analyte detection and with biological species. …