Polymer Chemistry Commons^™

An Investigation Of Poly(N-Isopropylacrylamide) For Applications With Microfluidic Paper-Based Analytical Devices, Haydn Thomas Mitchell

Master's Theses

N,N′-methylenebisacrylamide-crosslinked poly(N-isopropylacrylamide), also known as P(NIPAM), was developed as a fluid delivery system for use with microfluidic paper-based analytical devices (microPADs). MicroPADs are postage-stamp-sized devices made out of paper that can be used as platforms for low-cost, simple-to-use point-of-care diagnostic assays. P(NIPAM) is a thermally responsive polymer that absorbs aqueous solutions at room temperature and will expel the solutions to microPADs when heated. The fluid delivery characteristics of P(NIPAM) were assessed, and P(NIPAM) was able to deliver multiple solutions to microPADs in specific sequences or simultaneously in a laminar-flow configuration. P(NIPAM) was then shown to be suitable …

Development Of Quantitative Ft- Ir Methods For Analyzing The Cure Kinetics Of Epoxy Resins, Sang Ha Son

Open Access Dissertations

Epoxy thermosets are important engineering materials with applications in coating, adhesives, packaging and as structural components in a variety of advanced engineering products. The ultimate performance of polymer critically depends upon the details of the cure chemistry used to produce the thermoset. In order to better understand and monitor the cure chemistry, quantitative analysis of the FT-IR response has been developed for describing the epoxy-amine curing reaction as well as monitoring the hydrogen bonding that occurs in these systems The FT-IR analysis includes (i) quantitative deconvolution of complex peaks into individual spectral contributions, (ii) peak identification via DFT analysis and …

Development Of Colloid Displacement Lithography Platforms For Sensor Applications, Mahesh Thugu

Masters Theses & Specialist Projects

In this work, Poly (diallyldimethylammonium) chloride - (PDDA) was used as a base layer for developing colloid displacement lithography platforms for sensor applications. Previous work shows that glass coated with PDDA and exposed to gold acts as a good platform for colloid displacement lithography. However, for actual sensor applications, electrical isolation of individual sensor sections must be achieved. This is attempted by laying down a 40 μm stripe of PDDA on a cleaned substrate and coating that stripe with gold colloid. The size of 40 μm or less in width is set as the target to fit within the scan …

Polymers For Dna Binding, Sue Yuan Li

Seton Hall University Dissertations and Theses (ETDs)

.

Preparation And Rapid Analysis Of Antibacterial Silver, Copper And Zinc Doped Sol–Gel Surfaces, Brendan Duffy, Swarna Jaiswal, Patrick Mchale

Articles

The colonisation of clinical and industrial surfaces with microorganisms, including antibiotic-resistant strains, has promoted increased research into the development of effective antibacterial and antifouling coatings. This study describes the preparation of metal nitrate (Ag, Cu, Zn) doped methyltriethoxysilane (MTEOS) coatings and the rapid assessment of their antibacterial activity using polyproylene microtitre plates. Microtitre plate wells were coated with different volumes of liquid sol–gel and cured under various conditions. Curing parameters were analysed by thermogravimetric analysis (TGA) and visual examination. The optimum curing conditions were determined to be 50–70C using a volume of 200ul. The coated wells were challenged with Gram-positive …

Chemical Modification On Gold Slides To Gain Better Control Of Patterning Techniques, Ragini Vuppalapati

Masters Theses & Specialist Projects

Nanolithography is a rapidly evolving field that requires new combinations of techniques to improve patterning and to assist in fabricating electromechanical devices. An increasing number of applications require surfaces with defined regions of different chemical functionality. In our previous project optimum conditions for lithographic patterning were determined and potential blockers were identified to reduce force on the tip.

This work is focused on identifying good chemical modifications that will allow better control of basic patterning and to investigate the minimum force of patterning required while using each chemical system. The primary aim is to gain better control of basic pattern …

The Synthesis And Systematic Evaluation Of Modified Polymeric Foams And Electrically Conductive Polyimide/Carbon/Metal Films, John Macharia Kinyanjui

UNLV Theses, Dissertations, Professional Papers, and Capstones

Thermally processed PU foams are examined as a function of processing temperatures (25, 45, 65, and 85°C) at the side, middle, and center of a simple cylindrical mold. The PU foams show both chemical and morphological differences as a function of the processing temperature and radial position within the mold. Thermal degradation of uretoneimine structures, the emergence of carbodiimide structures, and extent of reaction of isocyanate groups are measured using photoacoustic FTIR spectroscopy. Chemical gradients and morphology differences between the side, middle, and center of the molded foam are observed for all processing temperatures. The data indicate that thermal activation …

Genetically Engineered Repetitive Polypeptides : Design, Synthesis, Characterization, And Applications, Natalya I. Topilina

Legacy Theses & Dissertations (2009 - 2024)

This work is dedicated to the investigation of protein folding with the emphasis on the aggregation and amyloid fibrils formation. The focus of the research is to elucidate the relationship between polypeptide chain sequence and folding/aggregation properties. For this purpose, i) libraries of the de novo macromolecular repetitive β-sheet forming polypeptides were designed, and ii) the strategy for their rapid creation was developed. The strategy enables retention of a basic polypeptide core, yet allowing variations in the repetitive sequence, degree of polymerization and distribution of specific amino acids. The polypeptides were expressed in E. coli, purified, and characterized by various …

A Selectivity Study On The Use Of Caffeine And Theobromine Imprinted Polypyrrole Surface Electrodes, Anil Kiran Kumar Vinjamuri

Masters Theses & Specialist Projects

Molecularly imprinted polymers (MIPs) are proving to be very effective in development of synthetic recognition systems and are of great interest to those interested in the field of sensor technology. The use of MIPs is receiving considerable interest due to the ability to prepare recognition matrices that possess high substrate selectivity and specificity. Conducting polymers (CP) have proved to be an excellent tool for the preparation of nano-structured biologically selective systems. Polypyrrole (Ppy) is one such CP that is extensively used for the construction of bioanalytical sensors. Ppy has shown great promise primarily due to its biocompatibility and thermal stability …