Chemistry Commons^™

Pd-Based Electrocatalysts For Oxygen Reduction And Ethanol Oxidation Reactions: Some Recent Insights Into Structures And Mechanisms, Zhi-Peng Wu, Chuan-Jian Zhong

Journal of Electrochemistry

The development of efficient electrocatalysts for applications in fuel cells, including proton-exchange membrane fuel cell (PEMFC) and direct ethanol fuel cell (DEFC), has attracted extensive research attention in recent years. Oxygen reduction reaction and ethanol oxidation reaction are two of the key reactions where the design of active, stable and low-cost electrocatalysts is critical for the mass commercializations of PEMFCs and DEFCs. This challenge stems largely from the limited understanding of the catalyst structures and reaction mechanisms. Progress has been made in investigations of electrocatalysts derived from Pd-based alloy nanomaterials both experimentally and computationally. We highlight herein some of the …

Suppressing Bias Stress Degradation In High Performance Solution Processed Organic Transistors Operating In Air, Hamna F. Iqbal, Qianxiang Ai, Karl J. Thorley, Hu Chen, Iain Mcculloch, Chad Risko, John E. Anthony, Oana D. Jurchescu

Chemistry Faculty Publications

Solution processed organic field effect transistors can become ubiquitous in flexible optoelectronics. While progress in material and device design has been astonishing, low environmental and operational stabilities remain longstanding problems obstructing their immediate deployment in real world applications. Here, we introduce a strategy to identify the most probable and severe degradation pathways in organic transistors and then implement a method to eliminate the main sources of instabilities. Real time monitoring of the energetic distribution and transformation of electronic trap states during device operation, in conjunction with simulations, revealed the nature of traps responsible for performance degradation. With this information, we …

Nitro Group Reduction For Use In Organic, Cathodic Materials, Brock G. Goeden

Honors Thesis

The industrial demand for higher capacity, light-weight battery materials has skyrocketed in recent years due to heavy investments in portable electronics, electronic vehicles, and renewable energy sources. However, rechargeable battery technology has seen little improvement since the invention of the Lithium-Ion battery in the 1980s. The low energy density of the traditionally utilized LiCoO2 cathodic material (specific capacity: 272 mAh g-1), has limited its potential to meet these increasing demands. To solve this problem, our research group is investigating new types of lightweight, organic, polymeric materials with conductive backbones as a possible replacement for the cathodic materials in Lithium-Ion batteries. …

Characterization Of Uranium, Lead, And Rare Earth Element Pollution In Natural Soils And Sediments, Hope Rasmussen

Civil and Environmental Engineering Theses and Dissertations

Heavy metals in the environment add to the global burden of pollution, negatively impacting public health and ecosystem resilience. This study included projects regarding uranium (U), lead (Pb), and rare earth elements (REE) in natural samples, due to their known toxicity, ubiquity, and relevance in context to recent pollution trends. The first project focused on testing the potential of using a hydroxyapatite product as a remediation solution for U-contaminated groundwater and soil at an EPA Superfund site. The results showed that the U was sequestered in a highly crystalline mineral form within the solids, guiding the EPA to specify the …

Bibliometric Analysis Of Named Entity Recognition For Chemoinformatics And Biomedical Information Extraction Of Ovarian Cancer, Vijayshri Khedkar, Charlotte Fernandes, Devshi Desai, Mansi R, Gurunath Chavan Dr, Sonali Tidke Dr., M. Karthikeyan Dr.

Library Philosophy and Practice (e-journal)

With the massive amount of data that has been generated in the form of unstructured text documents, Biomedical Named Entity Recognition (BioNER) is becoming increasingly important in the field of biomedical research. Since currently there does not exist any automatic archiving of the obtained results, a lot of this information remains hidden in the textual details and is not easily accessible for further analysis. Hence, text mining methods and natural language processing techniques are used for the extraction of information from such publications.Named entity recognition, is a subtask that comes under information extraction that focuses on finding and categorizing specific …

Polymer Based Triboelectric Nanogenerator For Cost‐Effective Green Energy Generation And Implementation Of Surface‐Charge Engineering, Diana Lopez, Aminur Rashid Chowdhury, Abu Masa Abdullah, Muhtasim Ul Karim Sadaf, Isaac Martinez, Brishty Deb Chowdhury, Serena Danti, Christopher J. Ellison, Karen Lozano, Mohammed Jasim Uddin

School of Integrative Biological & Chemical Sciences (Formerly Dept. of Chemistry)

Performance of triboelectric nanogenerators for harvesting mechanical energy from the ambient environment has been limited by structural complexity, cost-effectiveness, and mechanical weakness of materials. Herein, a cost-effective vertical contact separation mode triboelectric nanogenerator using polyethylene (PE) and polycarbonate (PC) in a regular digital versatile disc is reported. This cost-effective nanogenerator with simplified structures is able to generate an open-circuit voltage of 215.3 V and short-circuit current of 80 μA. The effects of the distance of impact and the air gap between the triboelectric layers have also been tested from 3 to 9 cm, and 0.25 to 1 cm, respectively. It …

Adsorption And Transport Of Colloids At Interface And In Bulk, Jingyun Lee

LSU Doctoral Dissertations

Colloids are suspensions of microscopic insoluble particles dispersed in a continuum phase such as liquid or gas. Colloids are found in our everyday life from food and cosmetic industries to pharmaceutical and biomedical applications. Depending on a global minimum of the free-energy landscape, colloidal suspensions can be classified as two major classes: equilibrium or active colloidal system. This Ph.D dissertation presents strategies to engineer equilibrium self-assembled structures and out-of-equilibrium active matter using various interparticle forces.

First, we introduce the means to promote the equilibrium self-assembled structures driven by adsorption of colloids at interface. Typically, adsorption of colloids at interface is …

Alternative View Of Oxygen Reduction On Porous Carbon Electrocatalysts: The Substance Of Complex Oxygen-Surface Interactions, Giacomo De Falco, Marc Florent, Jacek Jagiello, Yongqiang Cheng, Luke L. Daemen, Anibal J. Ramirez-Cuesta, Teresa J. Bandosz

Publications and Research

Electrochemical oxygen reduction reaction (ORR) is an important energy-related process requiring alternative catalysts to expensive platinum-based ones. Although recently some advancements in carbon catalysts have been reported, there is still a lack of understanding which surface features might enhance their efficiency for ORR. Through a detailed study of oxygen adsorption on carbon molecular sieves and using inelastic neutron scattering, we demonstrated here that the extent of oxygen adsorption/interactions with surface is an important parameter affecting ORR. It was found that both the strength of O2 physical adsorption in small pores and its specific interactions with surface ether functionalities in the …

A Systematic Multiscale Investigation Of Nanoparticle-Assisted Co2 Enhanced Oil Recovery (Eor) Process For Shale Oil Reservoirs, Dayo A. Afekare

LSU Doctoral Dissertations

Shale oil reservoirs are prolific on the short term due to hydraulic fracturing and horizontal drilling but experience significant production decline, leading to poor ultimate recovery and leaving billions of barrels of oil buried in the ground. In this study, a systematic multi-scale investigation of an enhanced oil recovery (EOR) process using relatively inexpensive silicon dioxide nanoparticles and carbon dioxide for shale oil reservoirs was conducted. Using the Tuscaloosa Marine Shale (TMS) as a case study, aqueous dispersions of nanosilica in conjunction with CO₂ were investigated at nano-to-core scales. At the nanoscale, atomic force microscope was used to investigate …

Nanocellulose Sheets From Oil Palm Empty Fruit Bunches Treated With Naoh Solution, Farah Fahma, Faiza Ayu Lestari, Ika Amalia Kartika, Nurmalisa Lisdayana, Evi Savitri Iriani

Karbala International Journal of Modern Science

The objective of this study is to produce nanocellulose sheets from oil palm empty fruit bunches (OPEFBs). Nanocellulose sheets from OPEFBs were prepared through the dewatering process using vacuum filtration. Subsequently, the produced sheets were treated with NaOH solution to improve the mechanical stability of their structure, causing them to be firm in water. The water absorption of nanocellulose sheet increased with increasing NaOH concentrations up to 20 wt%, increasing tensile strength, and Young’s modulus, but decreased when they were treated with 30 wt%. The diameter shrinkage of nanocellulose sheets was directly proportional to the NaOH concentration and soaking time. …

Blood Driven Biopower Cells: Acquiring Energy From Reverse Electrodialysis Using Sodium Concentrations From The Flow Of Human Blood, Efecan Pakkaner, Chase Smith, Christina Trexler, Jamie Hestekin, Christa Hestekin

Chemical Engineering Faculty Publications and Presentations

With the growth of the healthcare industry, small scale power sources are needed to support advancements in medical implants, artificial organs, and sensors throughout the body. However, it remains a challenge to find safe, reliable, and stable power sources for these devices. In this study, a miniaturized reverse electrodialysis (RED) biopower cell design using physiological salinity concentration differences between renal bloodstreams is explored for its potential to be used as a power supply for implantable medical devices. Two small scale RED devices produced consistent power for up to three to ten days, depending on the device design. A two-fold decrease …

Preparations And Electrocatalytic Ethanol Properties Of Palladium Intercalated Hydrotalcite, Shou-Xun Hu, Liang Li, Jun-Hao Yang, Liu-Qiang Li, Zhi-Hao Jin

Journal of Electrochemistry

High-performance electrocatalysts play a vital role in the commercial application of direct fuel cells. Current anode materials still have such problems as low activity, easy poisoning and high cost. In this study, a new type of nano- palladium (Pd) catalyst was prepared by dipping method using layered double hydroxides (LDHs) as the carrier. X-ray diffractometer, scanning electron microscope (SEM), inductively coupled plasma mass spectrometer (ICP-MS), energy spectrometer, transmission electron microscope (TEM), cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscope were used to analyze the structure and electrocatalytic performance of the catalyst. The results showed that the newly prepared Pd/Mg-Al-LDHs still maintained …

Theoretical Study On Electrical Properties Of Molecular Junctions Of Viologen Derivatives, Zhuan-Yun Cai, Jia Liu, Si-Yuan Guan, De-Yin Wu, Zhong-Qun Tian

Journal of Electrochemistry

In this paper, the electrical properties of molecular junctions formed N,N′-bis(4-thioalkyl)-4,4′-bipyridinium (viologen) moiety between two gold (Au) electrodes have been investigated by combining density functional theory and non-equilibrium Green’s functional approach. To modulate the viologen molecule to be a cation with one and two positive charges (V⁺ and V²⁺), we introduce one and two trifluoroacetic acid ions (TFA^-) around the molecule, respectively. The valence states of V⁺ and V²⁺ are confirmed by checking Mulliken and NBO charges. Then the relationship between molecular conductance and electronic structures of the neutral state …

Study On Li3Bo3 Interface Modification Of Garnet Solid Electrolyte, Gui-Wei Chen, Zheng-Liang Gong

Journal of Electrochemistry

Garnet solid-state electrolytes have become the research hotspot due to their high ionic conductivity, wide electrochemical stability window and good air stability. However, there are still a series of problems to be solved. The poor contact between the lithium (Li) metal and garnet pellet make it difficult to build stable ion diffusion channels, resulting in large interfacial resistance. The continuous growth of lithium dendrites can penetrate the electrolyte pellet and cause a short circuit in the solid-state battery. Herein, a novel strategy is proposed to improve the wettability of LLZTO electrolyte with Li metal, via interfacial modification of LLZTO electrolyte …

Preparation Of Pdcoir Tetrahedron Nanocatalysts And Its Performance Toward Ethanol Oxidation Reaction, Zhi-Yuan Yu, Rui Huang, Jie Liu, Guang Li, Qian-Tong Song, Shi-Gang Sun

Journal of Electrochemistry

As a new energy conversion device, direct ethanol fuel cells (DEFCs) are widely concerned because of their remarkable advantages such as high theoretical energy density and wide fuel sources. However, the rapid development of DEFCs has been severely impeded due to the sluggish kinetic process and toxic intermediates especially in their anodic reactions. Palladium (Pd)-based materials are considered to be excellent anode catalysts for DEFCs, especially under alkaline conditions. And further improving their performance is an important direction to promote the development of DEFCs. Surface structure and composition are the key factors affecting the performance of catalysts which can be …

Research Progress On Transition State Of Organic Electrode Materials, Xue-Qian Zhang, Zhou-Guang Lu, Wei-Wei Huang

Journal of Electrochemistry

With the increasing requirements for high energy density, long lifetime, high safety, environmentally friendly fabrication, and sustainable development of large energy storage devices, the society calls for new electrode materials in rechargeable batteries beyond traditional inorganic materials which are limited by specific capacity. Organic electrode materials have been widely used in rechargeable batteries due to their advantages of large theoretical capacity, designable structures and environmentally friendly fabrications. In this review, the radical intermediates of organic electrode materials produced in the charging-discharging process (redox reaction) and their types are systematically reviewed. The stability of radical intermediates controlled by changing the structure …

Research Progress Of Sio2 Regrowth During Selective Etching Process In 3d Nand Manufacture Procedure, Zi-Han Zhou, Yun-Wen Wu, Ming Li, Su Wang

Journal of Electrochemistry

As one of the most significant memory chips in semiconductor market, NAND has been developed from two-dimension (2D) to three-dimension (3D). Due to the three-dimensional memory structure of 3D NAND, the capacity density, read-write speed and reliability of memory chips have been greatly improved, as well as the reduction of power dissipation. It is by nitride-oxide selective etching process in the alternate stacked structure of 3D NAND that the inter-dielectric layers can be obtained. The more stack layers, the better performance of chips will be. Meanwhile, however, silicon dioxide (SiO₂) would regrow on the corner of oxide layers, …

Preparation And Performance Investigation Of Li-Sgo Doped Semi-Ipns Porous Single Ion Conducting Polymer Electrolyte, Yun-Feng Zhang, Jia-Ming Dong, Chang Tan, Shi-Kang Huo, Jia-Ying Wang, Yang He, Ya-Ying Wang

Journal of Electrochemistry

Herein, the lithiated sulfonated graphene oxide (Li-SGO) was successfully prepared via three steps by sulfonation of graphene oxide with 3-merraptnpropylt rimethnxysilane, oxidation of thiol into sulfonate with hydrogen peroxide and lithiation of sulfonate with aqueous lithium hydroxide. The as-prepared Li-SGO was then introduced into the semi-interpenetrating networks of single ion conducting polymer electrolyte (Li-SGO-FPAS) and poly vinylidenefluoride-hexafluoro propylene (PVDF-HFP) binder by in-situ polymerization to fabricate the porous single ion conducting polymer electrolyte membrane (Li-SGO-po-FPAS) generated from the poor compatibility between aromatic Li-SGO-FPAS and aliphatic PVDF-HFP binder. The key properties such as morphology, porosity, solvent uptake, mechanical …

Combined Applications Of Photocurrent Spectroscopy, Photoluminescence Spectroscopy And Uv-Vis Spectroscopy For Nano-Semiconductor Based Photoelectric Devices, Si-Da Bian, Jian-Zhang Zhou, Zhong-Hua Lin

Journal of Electrochemistry

The electronic structures and properties of nano-semiconductors are quite different from those of bulk semiconductors due to the nano-size effect (such as quantum size effect). Moreover, when the nano-semiconductor materials are deposited onto the substrate to construct a device, their electronic properties are also affected by the substrate or other components, which may lead to different performances of nano-semiconductors based photoelectric devices, and consequently, different corresponding characterization methods are needed. The combination of photocurrent spectroscopy, photoluminescence spectroscopy with UV-Vis absorption spectroscopy can provide a more comprehensive characterization for the electronic properties and photoelectrochemical performances of nano-semiconductors in photoelectric devices. Our …

Influence Of Resveratrol On Performance Of Long-Term Storage’S Lithium-Ion Battery Electrolyte, Lei Zhang, Xu-Ping Zhang, Si-Wei Zhang, Quan-Chao Zhuang

Journal of Electrochemistry

Electrolyte of lithium-ion battery usually goes through processes of filling, transportation and storage from the completion of manufacture to the use. Understanding the influence of long-term storage process on performance of lithium-ion battery electrolyte is of theoretical significance for production of lithium-ion battery. Scanning electron microscope (SEM) images showed that the solid electrolyte interface (SEI) film formed on the surface of the graphite electrode was thicker in the base electrolyte after 6 months of storage. The charge/discharge test results showed that the reversible cycle capacity and cycle stability (capacity retention rate) of graphite electrode decreased significantly after 6 months of …

Research Progress In Electrodeposition Technology Of Titanium-Based Iridium Oxide Electrode, Dan-Dan Wu, Xu Wu

Journal of Electrochemistry

Titanium-based iridium oxide electrode has been widely used in various fields, such as electrocatalytic oxidation, biomedical applications, hydrometallurgical metal recovery, electro-osmotic dewatering, etc. At present, it is mainly prepared by traditional thermal decomposition method, however, which has high cost, cumbersome process, mainly relying on manual labor and cannot be mass-produced yet. It is, therefore, urgently necessary to explore new preparation technologies by focusing on electrodeposition technology, with technological characteristics such as eco-friendly and sustainable development. This article systematically discusses the research progress in iridium oxide electrodeposition preparation technology from the aspects of deposition solution formulation, base material selection and treatment, …

Preparations And Electrochemical Properties Of Bc/Coni2S4@Ppy Flexible Composites For Supercapacitors, Si-Yuan Peng, Shi-Run Yang, Jing-Hong Zhou, Zhi-Jun Sui, Tao Zhang, Yi Shi, Xing-Gui Zhou

Journal of Electrochemistry

Flexible supercapacitor is one of the most promising energy storage devices for portable and wearable electronic products due to its advantages of high power density, fast charging and long cycle life. Therefore, self-supporting flexible electrode materials with high performance have attained more and more attention both in academia and in industry recently. In this work, using bacterial cellulose (BC) as a flexible substrate, the bacterial cellulose/nickel-cobalt sulfide@polypyrrole (BC/CoNi₂S₄@PPy) flexible composites with three-dimensional porous network and good conductivity were prepared by a combined solvothermal-in-situ polymerization-vacuum filtration method. The samples were characterized by X-ray diffraction, …

Syntheses Of Na3V2(Po4)2O2F As A Cathode For Sodium Ion Battery Application, Kai Wu

Journal of Electrochemistry

High-temperature solid-state method, hydro-thermal method and solvo-thermal method have been mainly employed to synthesize Na₃V₂(PO₄)₂O₂F (NVPF) cathode materials. However, these methods are energy consuming and complicated, which is not applicable for a large scale industrial production. In this study, a rather low-temperature (70℃) co-precipitation strategy was proposed to synthesize NVPF cathode materials. The as-prepared NVPF cathode materials showed a spherical shape with a diameter of 400 ~ 500 nm, and exhibited a sodium storage of 105.6 mAh·g^-1 and an efficiency of 90.06%. After a simple thermal process, the specific …

Characterization, Immobilization, And Polymer Related Applications Of Watermelon Seed Powder, A Practical Source Of Urease Enzyme, Anthony Quan Quoc Mai

LSU Doctoral Dissertations

Urease enzyme was crystallized almost a century ago, and to this day its intrinsic stability is not ideal for everyday applications. This work introduces a new process by which a naturally encapsulated material, watermelon seed powder (WMSP), is characterized for its stability and activity. WMSP enzymatic activity has been measured for over a year at various storage conditions—exposed to ambient atmosphere for a year, WMSP retained above 90% activity. In aqueous conditions, the enzyme maintained above 60% activity after two months; with the addition of a preservative that number stays at about 90%. There is a pH shift of the …

An Investigation Of Cross-Links On Crystallization And Degradation In A Novel, Photocross-Linkable Poly (Lactic Acid) System, Nicholas Baksh

USF Tampa Graduate Theses and Dissertations

Polymeric molecular structure consists of repeating units bonded together. Mechanicalproperties can be altered without affecting chemical makeup by altering the number of these units. Small molecules can be introduced and/or polymers can be modified to form bonds between molecular chains. Cross-linking, as this is called, also introduces mechanical variation with minimal effects on chemical composition. Lastly, polymer chains reorient themselves in response to intermolecular forces. This temperature dependent response is known as crystallization. Although chemistry is unaltered, mechanical properties can depend highly on the percent of the sample that is crystallized.

Cross-linking is known to enhance the mechanical properties of …

Exploring The Silent Aspect Of Carbon Nanopores, Teresa J. Bandosz

Publications and Research

Recently, owing to the discovery of graphene, porous carbons experienced a revitalization in their explorations. However, nowadays, the focus is more on search for suitable energy advancing catalysts sensing, energy storage or thermal/light absorbing features than on separations. In many of these processes, adsorption, although not emphasized sufficiently, can be a significant step. It can just provide a surface accumulation of molecules used in other application-driving chemical or physical phenomena or can be even an additional mechanism adding to the efficiency of the overall performance. However, that aspect of confined molecules in pores and their involvement in the overall performance …

Computational Modelling Enables Robust Multidimensional Nanoscopy, Matthew D. Lew

Electrical & Systems Engineering Publications and Presentations

The following sections are included:

• Present State of Computational Modelling in Fluorescence Nanoscopy

• Recent Contributions to Computational Modelling in Fluorescence Nanoscopy

• Outlook on Computational Modelling in Fluorescence Nanoscopy

• Acknowledgments

• References

Substituent Effects On The Solubility And Electronic Properties Of The Cyanine Dye Cy5: Density Functional And Time-Dependent Density Functional Theory Calculations, Austin Biaggne, William B. Knowlton, Bernard Yurke, Jeunghoon Lee, Lan Li

Materials Science and Engineering Faculty Publications and Presentations

The aggregation ability and exciton dynamics of dyes are largely affected by properties of the dye monomers. To facilitate aggregation and improve excitonic function, dyes can be engineered with substituents to exhibit optimal key properties, such as hydrophobicity, static dipole moment differences, and transition dipole moments. To determine how electron donating (D) and electron withdrawing (W) substituents impact the solvation, static dipole moments, and transition dipole moments of the pentamethine indocyanine dye Cy5, density functional theory (DFT) and time-dependent (TD-) DFT calculations were performed. The inclusion of substituents had large effects on the solvation energy of Cy5, with pairs of …

Nanoengineered Materials For Energy Conversion & Storage Applications: A Density Functional Theory Study, Ahmed Biby

Theses and Dissertations

The conventional approach for the development of novel materials has become long relative to the desired product development cycle. Thus, the sluggish pace of the development of materials within the conventional approach hinders the rapid transformation of the scientific outcomes into useful technological products. To this end, the field of hierarchical materials informatics evolved to bridge this gap. In this field, the multiscale material internal structure is considered the starting point and the core of this approach. This being said, the density functional theory (DFT) was used to generate useful materials data for the advancement of the hierarchical materials data-bases …

Coating Compositions And Methods For Using The Same, Fateme Rezaei, Thomas P. Schuman, Glenn Morrison

Chemical and Biochemical Engineering Faculty Research & Creative Works

Coating compositions and methods for using the same are disclosed. The coating compositions can include an aminosilica adsorbent. The coating compositions can adsorb CO₂.