Chemistry Commons^™

Effects Of Ti Addition On The Characteristics Of Al-10zn-6mg-2si/Zro2 Composites Produced By Squeeze Casting, Qesha Diva Prameshvara, Pipin Indah Lestari, Bondan Tiara Sofyan

Journal of Materials Exploration and Findings

Metal matrix composite (MMC) with 7xxx aluminum matrix is potential for ballistic applications due to the combination of strength, toughness, and light weight. Previous study successfully produced aluminum-based composites with SiC particles which were able to stop type III bullet, however cracks remained on back of the plate. Therefore, in this research, SiC was replaced by zirconia (ZrO₂) due to its high fracture toughness. Ti-B grain refiner was added to further improve toughness through grain boundary strengthening mechanism. This research developed 5 vol.% ZrO₂ strengthened Al-10Zn-6Mg-2Si composite with addition of Al-5Ti-1B grain refiner produced through squeeze casting …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Synthesis And Analysis Of A Novel Magnetic Surfactant, Donovan Turpin

Honors Theses

Researchers in the University of Mississippi Chemical Engineering Department have suggested that chelation of a large magnetic transition metal, namely dysprosium, into the large polar head group of a surfactant could result in a magnetic surfactant. This project was aimed at synthesizing a surfactant with a large enough head group and negative charge (specifically EDTA) to support this ion and demonstrating that the chelation process was successful. If so, the molecule would ideally be capable of forming micelles which could extract oily substances from water using a strong magnet—possibly applicable to environmental crises like oil spills.

NMR analysis has suggested, …

Model To Demonstrate Effects Of Mass Transfer And Applied Current In An Electrolytic Cell, George Ankrah

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

This study investigates the relationship between applied current and resulting cell potential in an electrolytic system, considering the transport of electroactive species. By applying Michael Faraday's laws of electrolysis and the Nernst-Planck equation, the behavior of electroactive species in diffusion-controlled systems with and without stirring is modeled. The plots demonstrate how stirring enhances ion transport and establishes a stable Nernst diffusion layer, affecting the kinetics of electrochemical reactions. Understanding these dynamics is crucial for optimizing electrolysis processes.

Review Of Cyclic Voltammetry Measurements For Uranium In Flinak Molten Salt, Jackson Ivory

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

The electrochemical behavior of uranium FLiNaK molten salts is explored, focusing on cyclic voltammetry (CV) as a powerful tool for redox characterization and diffusion studies. Through a comprehensive review of recent research, the study highlights the significance of CV in understanding electrode kinetics, material compatibility, and process optimization in molten salt environments. The findings underscore the potential of FLiNaK molten salt reactors in advancing nuclear energy technologies, fuel processing, and waste management strategies. Collaborative interdisciplinary efforts are emphasized to address challenges and accelerate innovation in electrochemical methods for nuclear applications.

Model Of The Effect Of Voltage On Contact Angle In An Electrolytic Cell Reaction, Aaron Essilfie

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

This paper investigates the hypothesis that the contact angle at the meniscus of an electrode-electrolyte can be altered during a redox reaction through the coupled understanding of electrowetting and capillarity rise. Recent studies in electrowetting have focused on dielectric surfaces but research on contact angle at the electrode-electrolyte surface is lacking. The study employs a basic electrolytic cell. By applying principles of electrowetting and capillary rise the research aims to understand the relationship between applied voltage and contact angle, to advancements in electrochemistry and microfluidics.

An Overview Of How To Measure The Kinetic Properties Of An Anode Material For The Chlorine Evolution Reaction, Cameron Vann

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

The process of generating chlorine gas using electrolysis in aqueous systems is well established. However, a new process requires chlorine to be generated at high temperatures using molten salt. This harsh environment requires a new study of anode materials for the chlorine evolution reaction. Anode materials can be compared by their kinetic parameters, the transfer coefficient α and the exchange current i0. The basic theory of these properties as they relate to the chlorine evolution reaction has been detailed and an analysis method for finding these effective parameters has been shown and demonstrated.

Investigating The Impact Of Secondary Activation Time On The Adsorption Properties Of Activated Biochar For Arsenic Removal From Wastewater, Achyuth Bharadwaj Rayarao

Graduate Theses and Dissertations (2019 - present)

Biochar, a naturally occurring and renewable carbon material, becomes porous through activation. Activated biochar is an ideal candidate for use as an adsorbent. The objective of this study is to investigate whether activated biochar derived from Colorado soft pine serves as a better adsorbent and demonstrates enhanced adsorption capabilities after undergoing secondary physical activation at various activation times. The effect of secondary action time on physical adsorption properties drawn from the analysis of isotherm plots, surface areas and pore size patterns were examined by using a physisorption analyzer. Chemical structures were identified using both ultimate and proximate analyses, while porosity …

Enabling High-Rate Thermoplastic Composite Manufacturing Through Structure-Processing-Property Relationships Of Polyphenylene Sulfide, Lina Ghanbari

Dissertations

In this dissertation, relationships between polyphenylene sulfide (PPS) chain structure and melt processing parameters are linked to thermoplastic composite (TPC) properties and mechanical performance. Deviations from linear PPS structure and the formation of branching/crosslinked moieties upon exposure to TPC manufacturing steps presents an opportunity to systematically uncover the interdependencies of melt-state thermal history on polymer rheology, crystallization, crystal structure, and translate these properties to the continuum level. This work first explores unreinforced PPS and how the formation of non-linear chain architectures yield altered rheological states when held at melt processing temperatures. These hindered chains exhibit unconventional crystallization behavior and non-uniform …

Analysis Of Additively Manufactured Inconel 718 Combustion Behavior In Promoted Oxygen Environments, Dominic George Dieguez

Open Access Theses & Dissertations

Promoted combustion testing is a vital tool for engineers to establish the combustion and flammability characteristics of materials (metallic or otherwise) in oxygen enriched environments. Historically, much of the established data for metallic promoted combustion has been with regards to materials in their cast and wrought forms. However, with the emergence of additive manufacturing as a preferred method of fabrication, the need exists to evaluate how metals in that form behave. Recent testing has demonstrated that even if a metal or alloy is nominally the same with regards to chemistry, flammability between samples in the wrought form can differ significantly …

Earth Abundant Catalyst For Evironmental Sustainability Applications, Javier Hernandez

Open Access Theses & Dissertations

The development of experimental methodologies for synthesizing a diverse range of metallic and metal oxide nanoparticles tailored for sustainable water treatment applications was investigated. These nanoparticles are prepared using environmentally friendly and scalable synthesis methods, underscoring their potential for large-scale production. Synthesized nanoparticles are harnessed for various processes, including catalysis and electrocatalysis, with a primary objective of degrading and removing organic pollutants from water. Key to this research is the encapsulation of nanoparticles within solid supports. Multiple methodologies are explored to engineer supports that ensure nanoparticle stabilization, monodispersion, and prevent unintended release into the environment. Two alternative approaches were evaluated …

Modeling Sex-Specific Changes In Myocardial Fibrosis, Grace Martin

Chemical Engineering Undergraduate Honors Theses

Heart disease the leading cause of death for both men and women in the United States. Cardiac fibrosis, or accumulation of extracellular matrix proteins in the heart, can occur after a heart attack and increase the risk for further complications. Current treatments for heart disease do not include extracellular matrix regulators, partly due to the complicated signaling network responsible for the production of these proteins. By using a computational model of the signaling network in cardia fibroblasts, the relationship between particular molecules and downstream extracellular matrix production can be examined.

Biological sex is an important factor for cardiac health and …

Relations Between Printability And Rheology In A Ceramic Paste Extrusion Process, Nicholas Durand

Open Access Theses & Dissertations

Ceramic additive manufacturing (AM) uses the same fundamentals as material extrusion (MEX) that utilizes polymers or resins for printing applications. Ceramic AM uses the same process of slicing an STL file to determine a toolpath for the printer that will facilitate material deposition to manufacture full parts; ceramic AM also provides a low-cost advantage when compared to processes that require high powered lasers for melting metal powders or heated nozzles used for dispensing thermoplastics. Despite having the similar design freedom and ability for rapid prototyping that other printing methods benefit from with the addition of low cost, ceramic AM has …

Selective Transfection Of A Transferrin Receptor-Expressing Cell Line With Dna-Lipid Nanoparticles And Synthesis Of Parasite-Derived Glycans As Biomarkers For Leishmaniasis, Irodiel Vinales Lozano

Open Access Theses & Dissertations

Despite notable progress in lipid nanoparticle (LNP)-mediated gene delivery, achieving selective transfection of specific cell types, such as cancer cells, remains a significant hurdle, hindering the advancement of innovative gene therapies. In this study, we engineered an LNP formulation encapsulating plasmid DNA (pDNA) encoding the monomeric Green Lantern (mGL) fluorescent reporter protein. The DT7 peptide ligand targeting human transferrin receptor 1 (hTfR1) was also conjugated to the LNP surface for targeted delivery to hTfR1-expressing cells. Optimization of LNP composition yielded favorable particle diameter, ζ-potential, yield, and pDNA encapsulation efficiency. Evaluation of transfection selectivity using a panel of two engineered cell …

Revealing The Three-Dimensional Arrangement Of Polar Topology In Nanoparticles, Chaewa Jeong, Juhyeok Lee, Hyesung Jo, Jaewhan Oh, Hionsuck Baik, Kyoung-June Go, Junwoo Son, Si-Young Choi, Sergey Prosandeev, Laurent Bellaiche, Yongsoo Yang

Physics Faculty Publications and Presentations

In the early 2000s, low dimensional ferroelectric systems were predicted to have topologically nontrivial polar structures, such as vortices or skyrmions, depending on mechanical or electrical boundary conditions. A few variants of these structures have been experimentally observed in thin film model systems, where they are engineered by balancing electrostatic charge and elastic distortion energies. However, the measurement and classification of topological textures for general ferroelectric nanostructures have remained elusive, as it requires mapping the local polarization at the atomic scale in three dimensions. Here we unveil topological polar structures in ferroelectric BaTiO₃ nanoparticles via atomic electron tomography, which …

Engineering Multifunctional Silicon Nanostructures From Biorenewable Cellulose Nanocrystals, Nancy Chen

All Dissertations

The imperative search for alternative materials to address the pressing demand for advance energy storage is underscored by the escalating environmental predicaments. Lithium-ion batteries (LIBs) with graphite anodes have become the benchmark in energy storage; however, they are approaching a saturation point in terms of energy density. Silicon emerges as a promising contender to supplant graphite, owing to its profuse availability, cost-effectiveness, and impressive specific capacity of 4200 mAh g^-1. By integrating silicon anodes, LIBs stand to undergo a radical transformation, markedly diminishing in weight and size, thus heralding a novel wave of compact, lightweight energy storage systems. …

Design And Application Of Smart Systems To Address Analytical Problems, Lucas B. Ayres

All Dissertations

This dissertation is a multidisciplinary effort that integrates low-cost analytical instrumentation, redox chemistry, and artificial intelligence to overcome existing limitations in the fields of wearable sensing technology, Deep Eutectic Solvents (DES), and antioxidant chemistry. The overall goal behind each implemented strategy is to enhance the accuracy, efficiency, and accessibility of analytical processes and technologies. A general overview of the thesis, along with the research outcomes is included in Chapter One. The theoretical framework of this dissertation is presented in Chapter Two. Chapter Three describes the development of a wearable platform (sensor and instrumentation) to rapidly detect (~20 minutes) S. aureus …

Performance Effects Of Dissociated Hydrogen In Nuclear Thermal Propulsion Engines, Richard Adam Gorrell

UNLV Theses, Dissertations, Professional Papers, and Capstones

Nuclear thermal propulsion (NTP) research considers hydrogen dissociation as negligible to design and analysis of propulsion engines. This study reintroduces chemically reacting flow to NTP engine analysis for investigation of the dissociation effect on engine performance. A first-principles approach observes the basic chemical mechanism and reaction within the high-speed, high-temperature NTP flow to baseline expected atomic hydrogen levels and validate equilibrium. A surface reaction study looks into hydrogen absorption through dissociation and its effect on the boundary layer, and bulk flow. For total performance, the resulting dissociated flow is analyzed through nozzle expansion and performance metrics calculated.

All historic reactor …

Boron-Doped Diamond As A Resilient Electrode Material In Molten Salts, Hannah Katherine Patenaude

UNLV Theses, Dissertations, Professional Papers, and Capstones

Molten salt chemistry has a range of applications within nuclear technology, including for the Molten Salt Reactors (MSRs) and pyroprocessing to recover valuable actinides for energy and national security needs. However, the high-temperature, corrosive nature of molten salts makes them particularly challenging to deploy on an industrial scale and study in benchtop measurements. Material accountability and corrosion monitoring of MSR fuels are essential components to the successful deployment of MSRs, and electroanalytical techniques like cyclic voltammetry (CV) and spectroelectrochemistry (SEC) can provide a wealth of information to describe salt systems in situ. To perform such measurements, it is imperative to …

Surface Treatments' Effects On The Capacitor's Dielectric Performance Under Electro-Thermal Stresses, Haider. M. Umran, Feipeng Wang

Karbala International Journal of Modern Science

Biaxial-oriented polypropylene (BOPP) films are characterized by unfavorable aging behavior because of their poor susceptibility to high temperatures, humidity, and high electric fields. This makes them unqualified to withstand harsh operating conditions, such as in capacitor applications. This study investigates the impact of annealing BOPP samples at 100 °C for five hours after fluorination at different times (15, 30, and 60 minutes) on their electrical and mechanical performance under electro-thermal stresses. Scanning electron microscope (SEM) images confirm that there is an increase in surface roughness and the formation of a dense layer of fluorine-containing groups monotonically with fluorination time. So, …

Electrocatalytic Cyclopropanation Of Active Methylene Compounds, Liang-Hua Jie, Hai-Chao Xu

Journal of Electrochemistry

The development of novel strategies to access cyclopropanes has become increasingly important due to the vital role of these three-membered ring structures in synthetic intermediates, natural products, and pharmaceuticals. Herein, we present an electrocatalytic method for the synthesis of cyclopropanes through intermolecular dehydrogenative annulation of active methylene compounds and arylalkenes. This electrochemical process requires no chemical oxidants, allowing for a speedy access to various functionalized cyclopropanes from inexpensive and readily available materials.

Electrochemical Advanced Treatment Of Desulfurization Wastewater From Coal-Fired Power Plants, Ju-Cai Wei, Juan Yi, Xu Wu

Journal of Electrochemistry

Zero-emission of desulfurization wastewater is one of the main demands for coal-fired power plants. As typical high salinity wastewater, it is hard to purify the desulfurization wastewater from coal-fired power plants through traditional physicochemical treatment or biochemical treatment, e.g., COD and Cl^–. A high concentration of Cl^– ion in desulfurization wastewater restricts wastewater reuse and zero-emission. Electrochemical technology is an attractive method for high salinity wastewater zero-emission, which provides a versatile, efficient, cost-effective, easily automatable, and clean industrial process. For advanced treatment of effluent after triple box process treatment in power plants, this paper reports an electrochemical …

Electrochemical Syntheses Of Aryl-Substituted Benzothiophenes And Phenanthrenes Using Benzenediazonium Salts As The Aryl Radical Precursors, Li-Yuan Lan, Yang-Ye Jiang, Raymond Daniel Little, Cheng-Chu Zeng

Journal of Electrochemistry

Aryl-substituted benzothiophene and phenanthrene are important structural units in medicinal chemistry and materials science. Although extensive effort has been devoted to prepare these compounds and a variety of approaches have been developed to construct the 2-substituted benzothiophene core structure, environmental-friendly and efficient synthetic means are still desired. Based on our previous electrochemical Minisci-type arylation reaction with aryl diazonium salt as the aryl precursor, as well as the work from König’s group, herein, we described the use of paired electrolysis to achieve 2-aryl benzothiophenes and 9-aryl phenanthrenes employing benzenediazonium salts as the aryl radical precursors. Initially, 2-methylthiobenzendiazonium salt 1a and 4-methylbenzene …

Seeding Effects Of Submicron Caal-No3 Ldh Particles On The Hydration And Properties Of Portland Cement And Sulfoaluminate Cement Pastes, Sukanta K. Mondal, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

Layered double hydroxide (LDH) is reported to improve the durability of concretes, primarily due to its ability to exchange anionic species, including chloride, which is implicated in corrosion-driven durability issues. However, there is no comprehensive study investigating the effect of LDH on the properties of different cement systems at both early and mature ages. in this study, the early age and mature age properties of Portland cement (OPC) and calcium sulfoaluminate (CSA) cement pastes seeded with submicron-sized calcium aluminum-NO3 LDH (CaAl-NO3 LDH) were investigated. the effects of the 1–5%mass dosage of LDH on the hydration of both cement systems were …

Quantifying Asphalt Binder Uv Effects With Relaxometry, Rosalee Brown

Undergraduate Research Conference at Missouri S&T

Asphalt deterioration involves many physical and chemical changes caused by environmental factors such as automotive strain, extreme heat, and UV exposure. Asphalt binder assessment in the industry is currently based on structurally destructive testing methods and tests of physical performance without accounting for chemical structure. An emerging evaluation of asphalt binder uses relaxometry, a field of nuclear magnetic resonance (NMR) spectroscopy, to directly observe how asphalt binder is changed by causes of deterioration such as UV exposure. NMR relaxometry explores nuclear spins' interactions with their environment. This noninvasive method can provide a detailed view into the chemical environment of virgin …

Iron Doped Zeolitic Materials For Propane Dehydrogenation Catalyst, Emily Cahill, Amitava Choudhury

Undergraduate Research Conference at Missouri S&T

This research describes the synthesis of iron-doped zeolitic catalysts for the transformation of propane to propylene. The goal of this research is to develop a dehydrogenation catalyst to convert shale-gas derived cheap propane feedstock to economically valuable propylene, while at the same time making this catalyst sustainable and non-toxic to the environment. Fedoped zeolitic frameworks have shown promising activity in percentage of conversion and in selectivity. In our study we analyzed zeolites ZSM-5 and AIP0-5. These were chosen because they have differences in pore structure , channel sizes, and connectivity between channels. Most importantly the differences in the chemistry as …

Thermal Frontal Polymerization – Applications In Coatings And Composites, Maria Martinez

LSU Doctoral Dissertations

Thermal frontal polymerization has long been used as a method to cure composites and coatings. However, this is the first time these applications have been used without the use of a catalyst, for the case of composites and coatings.

Chapter 2 discusses how to optimize cure-on-demand, thin layer coatings, using frontal polymerization. Previously, for the use of curing thin layer coating using thermal FP, it was known to just make the formulation viscous enough, as this would prevent premature quenching caused by heat loss. It was discovered that for a given layer thickness, a minimum viscosity and initiator concentration were …

Broadband Dielectric Spectroscopic Detection Of Volatile Organic Compounds With Zinc Oxide And Metal-Organic Frameworks As Solid-State Sensor Materials, Papa Kojo Amoah

Electrical & Computer Engineering Theses & Dissertations

The industrial revolution drove technological progress but also increased the release of harmful pollutants, posing significant risks to human health and the environment. Volatile organic compounds (VOCs), which have various anthropogenic and natural sources, are particularly concerning due to their impact on public health, especially in urban areas. Addressing these adverse effects requires comprehensive strategies for mitigation as traditional gas sensing techniques have limitations and there is a need for innovative approaches to VOC detection.

VOCs encompass a diverse group of chemicals with high volatility, emitted from various human activities and natural sources. These compounds play a crucial role in …

Development Of On-The-Fly Quasi-Steady State Approximation For Chemical Kinetics In Cfd, Abhinav Balamurugan

Doctoral Dissertations and Master's Theses

This study analyzes the feasibility of On-The-Fly Quasi-Steady-State Approximation (OTF-QSSA) application for solving chemical kinetics within Computational Fluid Dynamics (CFD) simulations, aiming to reduce the computational demand of detailed mechanisms. An algorithm that dynamically identifies and designates Quasi-Steady-State (QSS) species at specific grid locations and instances during the simulation was developed. With this information, our method pseudo-delays the advancement of concentrations for these QSS species—effectively setting their rate of concentration change to zero for a set number iteration before updating using the detailed mechanism and thereby omitting the computationally intensive processes typically required for their calculation during those skipped iteration. …

Shorting At Long Duration: Impact Of Extended Discharge Capacity On Battery Solid Electrolytes, Ryan C. Hill, Amanda S. Peretti, Leo J. Small, Erik D. Spoerke, Yang-Tse Cheng

Chemical and Materials Engineering Faculty Publications

Long-duration energy storage (LDES) is critical to a stable, resilient, and decarbonized electric grid. While batteries are emerging as important LDES devices, extended, high-power discharges necessary for cost-competitive LDES present new materials challenges. Focusing on a new generation of low-temperature molten sodium batteries, we explore here unique phenomena related to long-duration discharge through a well-known solid electrolyte, NaSICON. Specifically, molten sodium symmetric cells at 110 ° C were cycled at 0.1 A cm−2 for 1–23 h discharges. Longer discharges led to unstable overpotentials, reduced resistances, and decreased electrolyte strength, caused by massive sodium penetration not observed in shorter duration discharges. …