Open Access. Powered by Scholars. Published by Universities.®

Operations Research, Systems Engineering and Industrial Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Industrial Engineering

Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 2881 - 2910 of 3572

Full-Text Articles in Operations Research, Systems Engineering and Industrial Engineering

Double Perforated Impingement Plate (Dpip) In Shell-And-Tube Heat Exchanger, S. S. Al-Anizi, A. M. Al-Otaibi Jul 2007

Double Perforated Impingement Plate (Dpip) In Shell-And-Tube Heat Exchanger, S. S. Al-Anizi, A. M. Al-Otaibi

Heat Exchanger Fouling and Cleaning VII

This paper presents a solution to a chronic problem causing repeated tube failure at shell-and-tube heat exchangers. The problem is related to fouling process on tubes surface which accumulates downstream the impingement plate at exchanger inlet nozzle within the first tube rows due to low velocity and vortices production. In fouling services, the suspended deposits, fouling, accumulates on tubes surface downstream the impingement plate causing under-deposit corrosion and raising tubes surface temperature due to lack of cooling accelerating fouling process. Under fouling corrosion attacks tubes and causes repeated tube failure costing a lot of money in terms of material, maintenance …

Go to article

Towards An Understanding Of How Tube Inserts Mitigate Fouling In Heat Exchangers, B. Aquino, C. Derouin, G.T. Polley Jul 2007

Towards An Understanding Of How Tube Inserts Mitigate Fouling In Heat Exchangers, B. Aquino, C. Derouin, G.T. Polley

Heat Exchanger Fouling and Cleaning VII

A number of studies undertaken by Total have measured the improvement that can be expected when TurbotalTM inserts are installed in heat exchangers. These studies have fully established that TurbotalTM both improve heat transfer coefficient and mitigate fouling. It has been found that fouling levels vary with application. Consequently, economics of installing inserts are difficult to quantify. Gains must be estimated through specific tests. A model that predicts fouling development solves this problem. In this paper first steps towards the understanding of how TurbotalTM limits the fouling rate are described. Authors suggest that the calculation of both pressure drop and …

Go to article

Cleaning High-Speed Marine Separators With An Environmentally-Friendly Cip Agent, Ulf Nylén, Roger Andersson, Peter Forsberg Jul 2007

Cleaning High-Speed Marine Separators With An Environmentally-Friendly Cip Agent, Ulf Nylén, Roger Andersson, Peter Forsberg

Heat Exchanger Fouling and Cleaning VII

The present contribution is devoted to the cleaning of high-speed marine separators employing the environmentally-friendly Cleaning In Place (CIP) agent Alpacon Multi Cip Super. For this particular study an Alfa Laval lube oil separator of type S831 on board the ship MS Isabella was dismantled prior to its first CIP treatment since installation and a few of the sludge-coated insert discs were taken as samples for laboratory experiments. Following assembly, the separator was cleaned according to a standard CIP protocol. Back in the laboratory, experiments mimicking the field CIP conditions verified the excellent cleaning results observed by visual inspection out …

Go to article

Biofouling Control In Heat Exchangers Using High Voltage Capacitance Based Technology, R. Romo, M. M. Pitts, N. B. Handagama Jul 2007

Biofouling Control In Heat Exchangers Using High Voltage Capacitance Based Technology, R. Romo, M. M. Pitts, N. B. Handagama

Heat Exchanger Fouling and Cleaning VII

Biofouling in industrial heat exchangers and piping systems is common in water from all sources. Problems generated by biofouling such as corrosion, sludge deposition and scale formation have a costly impact on industrial equipment and productivity. This paper describes an electronic approach using High Voltage Capacitance Based technology (HVCB) to control biofouling in industrial heat exchangers, focusing upon biofilm removal and the prevention of biofilm formation. Four different application case studies are presented in this paper in which the HVCB technology was used to control biofouling. The applications include an evaporative cooling wall in a greenhouse in Oracle, Arizona; a …

Go to article

Cleaning Monitoring Using Controlled Nano-Vibrations, A. Pereira, J. Mendes, L.F. Melo Jul 2007

Cleaning Monitoring Using Controlled Nano-Vibrations, A. Pereira, J. Mendes, L.F. Melo

Heat Exchanger Fouling and Cleaning VII

The monitoring of fouling and cleaning has become very important in order to optimize production cycles, to increase the quality of the final product and to reduce environmental impacts. The aim of the study here presented was to use the MSS – Mechatronic Surface Sensor, to detect the cleaning end-point of hair shampoo removal under different cleaning conditions. It was found that this new monitoring tool was able to clearly identify when the equipment was cleaned, producing different cleaning curves for different cleaning conditions.

Go to article

Solving A Hydtrotreater Feed Filter Fouling Problem, X.A. Wu, K.H. Chung Jul 2007

Solving A Hydtrotreater Feed Filter Fouling Problem, X.A. Wu, K.H. Chung

Heat Exchanger Fouling and Cleaning VII

Feed filters were installed in Syncrude hydrotreater units to protect the catalyst beds from plugging by fine solids in the feed. Severe filter fouling occurred after a process flow sheet change. The root cause of fouling was revealed through a step-by-step scientific investigation. It was first confirmed that the fouling problem was related to a process flow sheet change that introduced a heavy vacuum gas oil (HVGO) stream into the coker combined gas oil (KCGO) stream prior to filtration. Characterization of the foulant and the feed indicated that the fouling reactions are likely oxidative polymerization. Iron naphthenate or naphthenic acid …

Go to article

Electrochemical Impedance And Digital Image Methods To Detect Initial Deposition Of Microorganisms, H. Men, S. W. Mu, Z. W. Lu, Y. L. Chen, S.R. Yang, Y. P. Jia, S. X. Cao Jul 2007

Electrochemical Impedance And Digital Image Methods To Detect Initial Deposition Of Microorganisms, H. Men, S. W. Mu, Z. W. Lu, Y. L. Chen, S.R. Yang, Y. P. Jia, S. X. Cao

Heat Exchanger Fouling and Cleaning VII

Microorganism in industrial cooling water can cause corrosion and biofouling. Electrochemical impedance method and digital image method (DIM) were used to detect quantitatively iron bacteria and heterotrophic bacteria. Microorganism growth and metabolism can change the impedance of culture medium. The detection time of impedance variation lie in the function relationship with the logarithm of bacteria concentration. 7-million-pixel CCD sensor was used to shoot the shape of microorganism in order to count the number. Compared with most probable number (MPN) method, the detection time of electrochemical impedance is shortened. The DIM reduces the bacteria counting time and the inaccuracy associated with …

Go to article

Slag Monitoring System For Combustion Chambers Of Steam Boilers, J. Taler, D. Taler Jul 2007

Slag Monitoring System For Combustion Chambers Of Steam Boilers, J. Taler, D. Taler

Heat Exchanger Fouling and Cleaning VII

The computer based boiler performance system, presented in this paper, has been developed to provide a direct and quantitative assessment of furnace and convective surface cleanliness. Temperature, pressure and flow measurements and gas analysis data are used to perform heat transfer analysis in the boiler furnace and evaporator. Power boiler efficiency is calculated using an indirect method. The on-line calculation of the exit flue gas temperature in a combustion chamber allows for an on-line heat flow rate determination, which is transferred to the boiler evaporator. Based on the energy balance for the boiler evaporator, the superheated steam mass flow rate …

Go to article

Cover Page, Hans Müller-Steinhagen, M. Reza Malayeri, Paul Watkinson Jul 2007

Cover Page, Hans Müller-Steinhagen, M. Reza Malayeri, Paul Watkinson

Heat Exchanger Fouling and Cleaning VII

No abstract provided.

Go to article

Free Alkali-Index For Optimizing The Fuel Mixture In Biomass Co-Firing, T.E. Blomberg Jul 2007

Free Alkali-Index For Optimizing The Fuel Mixture In Biomass Co-Firing, T.E. Blomberg

Heat Exchanger Fouling and Cleaning VII

Co-firing biomass with fossil fuels provides a cheap and efficient reduction of the CO2 emissions in electricity generation. One of the main challenges in co-firing is the increased fouling and corrosion rates of the heat transfer surfaces when biomass is added to the fuel mixture. Optimization of the fuel mixture from the fouling and corrosion point of view would be an easier task, if some fuel properties would provide correlation with the fouling and corrosion rates. Currently there is no clear understanding of the most useful fuel indices. The fouling indices used in coal firing have proved to be less …

Go to article

The Science Of Cleaning Of Dairy Fouling Layers, R. Mercadé-Prieto,, W.R. Paterson, D.I. Wilson Jul 2007

The Science Of Cleaning Of Dairy Fouling Layers, R. Mercadé-Prieto,, W.R. Paterson, D.I. Wilson

Heat Exchanger Fouling and Cleaning VII

The science underlying the removal of dairy fouling layers, and particularly the dissolution of proteinaceous deposits in alkaline solution, is relatively poorly understood even though this is a critical feature of many cleaning-in-place operations. We report key results from a series of investigations on heat-induced gels of β- lactoglobulin, the primary whey protein component in milk and whey foulant. These model systems were used to elucidate the reaction behaviour of gels and aggregates whereby the proteinaceous material is converted to a softer, swollen form that can then be removed by fluid shear or diffusion. We show that several features, such …

Go to article

Study Of An Organic Crystallization Fouling Problem, Hirofumi Inokuchi, Mitsutaka Nakamura, Yoshio Koga Jul 2007

Study Of An Organic Crystallization Fouling Problem, Hirofumi Inokuchi, Mitsutaka Nakamura, Yoshio Koga

Heat Exchanger Fouling and Cleaning VII

One of the aromatic compound plants in Mitsubishi Chemical Corporation has a heavy crystallization fouling problem. We have been studying the crystallization process using the shell and tube heat-exchanger. In order to solve our fouling problem of the heat exchanger, we developed the specified evaluation equipment (crystallization fouling simulator : CFS) which consists of a single tube heatexchanger (Tube size: ID=10.3mm Length=500mm). The result of the modeling for describing the crystallization fouling rate and the countermeasure of the fouling problem are discussed in this work. It can be possible to describe the fouling rate as one equation which has two …

Go to article

Bacterial And Protein Adhesion On Ni-P-Ptfe Coated Surfaces, Q. Zhao, C. Liu, Y. Liu, S. Wang Jul 2007

Bacterial And Protein Adhesion On Ni-P-Ptfe Coated Surfaces, Q. Zhao, C. Liu, Y. Liu, S. Wang

Heat Exchanger Fouling and Cleaning VII

The adhesion of bacteria and proteins on the surfaces of heat exchangers and food processing equipment has been recognized as a widespread problem. Biofouling not only reduces heat transfer performance significantly, but also causes considerable pressure drop, calling for higher pumping requirements. Biofouling also present a considerable hygiene risk in the food industry. It would be much more desirable if surfaces with an inherently lower stickability for biofouling could be developed. In this paper, stainless steel 304 plates were modified by electroless plating Ni-P and small amounts of PTFE. The experimental results showed that the surface free energy of the …

Go to article

Evaluation Of Heat Transfer Boundary Conditions For Cfd Modeling Of A 3d Plate Heat Exchanger Geometry, T.M. Pääkkönen, M. Riihimäki, R. Ylönen, E. Muurinen, C.J. Simonson, R.L. Keiski Jul 2007

Evaluation Of Heat Transfer Boundary Conditions For Cfd Modeling Of A 3d Plate Heat Exchanger Geometry, T.M. Pääkkönen, M. Riihimäki, R. Ylönen, E. Muurinen, C.J. Simonson, R.L. Keiski

Heat Exchanger Fouling and Cleaning VII

In this paper fluid flow and heat transfer are modeled in a corrugated 3D plate heat exchanger geometry with a commercial computational fluid dynamics (CFD) program, Fluent 6.1.22 (Fluent Inc., Lebanon), in order to find out the most realistic heat transfer boundary conditions for a plate heat exchanger. The built-in boundary conditions of Fluent available for this case are Heat flux, Convection and Constant wall temperature. The CFD models are verified with correlations and experimental data obtained by a flat plate test equipment of which parameters can be calculated analytically. Deficiencies are found in all the built-in heat transfer boundary …

Go to article

Metallic Micro Heat Exchangers: Properties, Applications And Long Term Stability, J.J. Brandner, W. Benzinger, U. Schygulla, S. Zimmermann, K. Schubert Jul 2007

Metallic Micro Heat Exchangers: Properties, Applications And Long Term Stability, J.J. Brandner, W. Benzinger, U. Schygulla, S. Zimmermann, K. Schubert

Heat Exchanger Fouling and Cleaning VII

Micro heat exchangers, which until recently have been implemented only at laboratory scale, are now being available for industrial applications. They are well known for their superior heat transfer properties due to the large surface-to-volume ratio. But there are little data available on the long term stability of these devices. In this paper application several application examples for micro heat exchangers made of stainless steel are presented. The devices consist of stainless steel foils providing numerous micro channels generated by mechanical micromachining or wet chemical etching. A number of the foils are arranged in a specific way and bonded together. …

Go to article

Fouling Monitoring And Cleaning Optimisation In A Heat Exchanger Network Of A Crude Distillation Unit, Andrea Heins, Ramón Veiga, Carlos Ruiz, Andrés Riera Jul 2007

Fouling Monitoring And Cleaning Optimisation In A Heat Exchanger Network Of A Crude Distillation Unit, Andrea Heins, Ramón Veiga, Carlos Ruiz, Andrés Riera

Heat Exchanger Fouling and Cleaning VII

Fouling in preheat networks of crude distillation units (CDU) plays an important role in energy consumption. In this work a procedure to monitor the performance of the heat exchanger network (HEN) and to optimize the cleaning strategies is presented. The procedure is based on a rigorous simulation of the HEN using Hysys (from Aspen Technology). The simulation is used to estimate the service overall heat transfer coefficient with real operational data acquired from the unit’s Plant Information System (PI). The clean overall heat transfer coefficient is calculated for each one of the individual heat exchangers with a rigorous simulation using …

Go to article

Cfd And Neural Network-Based Expert System For The Supervision Of Boilers And Furnaces, Hugo Calisto, Nelson Martins, Naim Afgan Jul 2007

Cfd And Neural Network-Based Expert System For The Supervision Of Boilers And Furnaces, Hugo Calisto, Nelson Martins, Naim Afgan

Heat Exchanger Fouling and Cleaning VII

CFD (Computational Fluid Dynamics) tools were used to build a "virtual" furnace, validated with experimental data. This model was used to simulate both normal and “faulty” behaviours, regarding parameters such as energy conversion efficiency, steam leakage and fouling. A database was developed comprising normal situations and simulated fault sets, characterized by virtual sensor outputs used in the evaluation of diagnostic parameters patterns to be processed and recognized by the diagnostic system. The database was processed using Neural Networks, with satisfactory results even in their most simple form (backpropagation networks) trained using standard algorithms. Pattern recognition was thus performed, identifying root …

Go to article

Preliminary Estimates Of Building Cost And The Lowest Evaluated Tender, Harriet Eliufoo Jun 2007

Preliminary Estimates Of Building Cost And The Lowest Evaluated Tender, Harriet Eliufoo

Tanzania Journal of Engineering and Technology (TJET)

The paper has investigated and established to what extent are preliminary estimates of building costs close to the lowest evaluated tender and how geographical proximity influences the variance between preliminary estimate and the lowest evaluated tender. A multiple case study constituting 43 building projects in Tanzania were statistically analysed covering a period from 1995- 1999. Findings reveal a significant variance exists between the quantity surveyor’s preliminary estimate figure and the lowest evaluated tender; and that the variance between the quantity surveyor’s figure and the bidder is small when the proposed building project is geographically closer to the quantity surveyor’s base. …

Go to article

Fabrication Of Net-Shape Functionally Graded Composites By Electrophoretic Deposition And Sintering: Modeling And Experimentation, E.A. Olevsky, X. Wang, A. Maximenko, M.A. Meyers Jun 2007

Fabrication Of Net-Shape Functionally Graded Composites By Electrophoretic Deposition And Sintering: Modeling And Experimentation, E.A. Olevsky, X. Wang, A. Maximenko, M.A. Meyers

Industrial and Manufacturing Engineering

It is shown that electrophoretic deposition (EPD) sintering is a technological sequence that is capable of producing net-shape bulk functionally graded materials (FGM). By controlling the shape of the deposition electrode, components of complex shapes can be obtained. To enable sintering net-shape capabilities, a novel optimization algorithm and procedure for the fabrication of net-shape functionally graded composites by EPD and sintering has been developed. The initial shape of the green specimen produced by EPD is designed in such a way that the required final shape is achieved after sintering-imposed distortions. The optimization is based on a special innovative iteration procedure …

Go to article

Development Of Prediction Models To Measure Vendor Performance In Surveillance And Auditing Of Aircraft Maintenance, Nikhil Iyengar May 2007

Development Of Prediction Models To Measure Vendor Performance In Surveillance And Auditing Of Aircraft Maintenance, Nikhil Iyengar

All Dissertations

Elimination of aviation accidents is one of the primary goals of the Federal Aviation Administration (FAA) and the airline industry. A leading cause of aviation accidents is lack of oversight of various organizational issues, in particular, the organization's maintenance operation performance. The technologies used in the industry generate multiple risks, mostly from three domains: systems, hardware and people. Maintenance performance analyses identify the inherent risk in distributed, large-scale systems. Analysis of existing aviation maintenance data is a crucial step in meeting the aviation industry's need to improve aviation safety. Presently, we lack suitable tools to analyze large bodies of maintenance …

Go to article

An Experimental Evaluation Of Performance Variance For Internally Threaded Geometry Related To Extended Tap Wear In Low Carbon Steel, Todd E. Alberts May 2007

An Experimental Evaluation Of Performance Variance For Internally Threaded Geometry Related To Extended Tap Wear In Low Carbon Steel, Todd E. Alberts

All-Inclusive List of Electronic Theses and Dissertations

The development of internal threads in a manufactured part is in many cases one of the final operations in the production workflow. Quality issues in thread form development can destroy a part that has previously undergone expensive machining. The issue of tap wear is one of the multi-faceted elements that have a direct correlation on the quality of threaded components. The purpose of this research centers on resultant mechanical pull performance for the stripping of internally threaded geometry in low carbon steel as measured over various increments of the tap cutting life cycle.

Go to article

Models Of Semi-Systematic Visual Search, Sourav Das May 2007

Models Of Semi-Systematic Visual Search, Sourav Das

All Dissertations

Visual search is an important aspect of many examination and monitoring tasks. As a result, visual search performance has been the topic of many empirical investigations. These investigations have reported that individual search performance depends on subject factors such as search behavior, which has motivated the development of models of visual search that incorporate this behavior. Search behavior ranges from random to strictly systematic; variation in behavior is commonly assumed to be caused by differences in memory retrieval and search strategy. Accordingly, a mathematical model of semi-systematic search is proposed here that can account for both memory retrieval and other …

Go to article

Investigation Of The Lead-Free Solder Joint Shear Performance, James Webster, Jianbiao Pan, Brian J. Toleno Apr 2007

Investigation Of The Lead-Free Solder Joint Shear Performance, James Webster, Jianbiao Pan, Brian J. Toleno

Industrial and Manufacturing Engineering

Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The purpose of this study is to investigate the effects of reflow profile and thermal shock on the shear performance of eutectic SnPb (SnPb) and Sn3.0Ag0.5Cu (SAC305) solder joints. Test boards were assembled with four different sized surface mount chip resistors (1206, 0805, 0603 and 0402). Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb were developed with three levels of peak temperature (12ºC, 22ºC, and 32ºC above solder liquidus temperature, or 230ºC, 240ºC, and 250ºC for SAC …

Go to article

Determining Underlying Characteristics Of Supplier Evaluation Model: A Quantitative Empirical Research, Zeynep Ozlem Ozgun Apr 2007

Determining Underlying Characteristics Of Supplier Evaluation Model: A Quantitative Empirical Research, Zeynep Ozlem Ozgun

Engineering Management & Systems Engineering Theses & Dissertations

Rapid changes in the business environment, driven by competitive pressures and business complexity, present challenges that organizations cannot address without the support of their suppliers. In the past decades, performance evaluation factors such as quality, delivery, and price have been widely used by organizations to measure their suppliers' performance. Traditional supplier performance dimensions now considered to be only single dimensional, and not guarantee long term success of an organization. Use of internationally recognized standards and guidelines such as ISO 9000, MBNQA are recommended to be feasible for supplier Quality Management System evaluation in the literature. However, their effectiveness as a …

Go to article

Synthesis Of Gold Micro- And Nano-Wires By Infiltration And Thermolysis, E.A. Olevsky, X. Wang, E. Bruce, M.B. Stern, S. Wildhack, F. Aldinger Feb 2007

Synthesis Of Gold Micro- And Nano-Wires By Infiltration And Thermolysis, E.A. Olevsky, X. Wang, E. Bruce, M.B. Stern, S. Wildhack, F. Aldinger

Industrial and Manufacturing Engineering

An approach for synthesizing micro- and nano-sized gold wires by infiltration and thermolysis is investigated. A porous ZrO2 ceramic preform with aligned pores obtained by unidirectional freezing and freeze-drying is employed as an infiltration template. The sintered porous ZrO2 preform is then infiltrated by a brushing gold solution. The thermolysis is conducted at 600 °C in air. Micro- and nano-sized gold wires are developed within the walls of the pores after thermolysis. The diameter of the gold wires ranges from several hundred nanometers to several microns.

Go to article

Backward And Forward Compatibility, Jianbiao Pan, Jasbir Bath, Xiang Zhou, Dennis Willie Jan 2007

Backward And Forward Compatibility, Jianbiao Pan, Jasbir Bath, Xiang Zhou, Dennis Willie

Industrial and Manufacturing Engineering

In response to the European Union (EU) Restriction of Hazardous Substances (RoHS) and other countries’ impending lead-free directives, the electronics industry is moving toward lead-free soldering. Total lead-free soldering requires not only lead-free solder paste but also lead-free printed circuit board (PCB) finish and lead-free component/packages. Transitioning tin-lead (SnPb) soldering to totally lead-free soldering is a complex issue and involves movement of the whole electronics industry supply chain. In reality, there is a transition period.

Go to article

A Framework For The Assessment And Analysis Of Multi-Hazardsinduced Risk Resulting From Space Vehicles Operations, Serge Sala-Diakanda Jan 2007

A Framework For The Assessment And Analysis Of Multi-Hazardsinduced Risk Resulting From Space Vehicles Operations, Serge Sala-Diakanda

Electronic Theses and Dissertations

With the foreseeable increase in traffic frequency to and from orbit, the safe operation of current and future space vehicles at designated spaceports has become a serious concern. Due to their high explosive energy potential, operating those launch vehicles presents a real risk to: (1) the spaceport infrastructure and personnel, (2) the communities surrounding the spaceport and (3) the flying aircrafts whose routes could be relatively close to spaceport launch and reentry routes. Several computer models aimed at modeling the effects of the different hazards generated by the breakup of such vehicles (e.g., fragmentation of debris, release of toxic gases, …

Go to article

Details And Description Of Operations Research, Paul Savory Jan 2007

Details And Description Of Operations Research, Paul Savory

Department of Industrial and Management Systems Engineering: Reports

The ambiguous term operations research was coined during World War II. A frequent substitute is management science. Operations research is a scientific approach to analyzing problems and making decisions. It uses mathematics and mathematical modeling on computers to forecast the implications of various choices and zero in on the best alternatives. This content paper provides an overview of operations research. It highlights operations research problems, methods for solving problems, different areas of operations research, and example problems.

Go to article

Pre/Post Assessment Of Abilities, Paul Savory Jan 2007

Pre/Post Assessment Of Abilities, Paul Savory

Department of Industrial and Management Systems Engineering: Instructional Materials

One approach to assess if students are learning in a course is to conduct a pre-test, post-test assessment of the course material. By comparing the two results, one can make an assessment of the knowledge learned in the course. For certain types of courses, it can be a challenge in defining an assessment instrument that measure student knowledge. This example is one I have developed for my IMSE 440/840 (Discrete Event Computer Simulation) course. Students are asked rate their ability for key course objectives defined on the course syllabus. I administer it on the first day of the course and …

Go to article

Methodology For Analyzing And Characterizing Error Generation In Presence Of Autocorrelated Demands In Stochastic Inventory Models, Rafael Diaz Jan 2007

Methodology For Analyzing And Characterizing Error Generation In Presence Of Autocorrelated Demands In Stochastic Inventory Models, Rafael Diaz

Computational Modeling & Simulation Engineering Theses & Dissertations

Most techniques that describe and solve stochastic inventory problems rely upon the assumption of identically and independently distributed (IID) demands. Stochastic inventory formulations that fail to capture serially-correlated components in the demand lead to serious errors. This dissertation provides a robust method that approximates solutions to the stochastic inventory problem where the control review system is continuous, the demand contains autocorrelated components, and the lost sales case is considered. A simulation optimization technique based on simulated annealing (SA), pattern search (PS), and ranking and selection (R&S) is developed and used to generate near-optimal solutions. The proposed method accounts for the …

Go to article

First Prev Next Last