Manufacturing Commons^™

Multi-Axis Planning System (Maps) For Hybrid Laser Metal Deposition Processes, Frank W. Liou, Jianzhong Ruan, Todd E. Sparks

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper summarizes the research and development of a Multi-Axis Planning System (MAPS) for hybrid laser metal deposition processes. The project goal is to enable the current direct metal deposition systems to fully control and utilize multi-axis capability to make complex parts. MAPS allows fully automated process planning for multi-axis layered manufacturing to control direct metal deposition machines for automated fabrication. Such a capability will lead to dramatic reductions in lead time and manufacturing costs for high-value, low-volume components with high performance material. The overall approach, slicing algorithm, machine simulation for planning validation, and the planning results will be presented.

Optimization Of Selective Laser Sintering Process For Fabrication Of Zirconium Diboride Parts, Ming-Chuan Leu, Shashwatashish Pattnaik, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Selective Laser Sintering (SLS) was investigated to fabricate Zirconium Diboride (ZrB₂) parts for ultra-high temperature applications. Experiments were conducted to determine values of SLS process parameters (laser power, scan speed, line spacing, and layer thickness) that can be used to build ZrB₂ parts with high integrity and sharp geometrical features. A sacrificial plate with a proper number of layers (determined from experimentation) separated from the main part was built in order to reduce thermal gradients when building the main part. The sacrificial plate was found to assist in eliminating cracks in the bottom of the main part. …

Development Of A Low Cost Imaging System For A Laser Metal Deposition Process, Shyam Barua, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The size of the melt pool created by the laser is one of the most important quality characteristic in a laser metal deposition process. This paper discusses the development of a low-cost vision system to automatically determine the size of the melt pool for in-process control. To cope with the intense infrared signal from the laser and melt pool, external ultraviolet illumination is paired with narrow bandpass filters on a usb microscope to achieve a clear image of the melt pool. The sensitivity of the melt pool to changes in system parameters and various substrate materials are also evaluated.

Uncertainty Analysis In Laser Deposition Finish Machining Operations, Jomy Francis, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Laser Aided Manufacturing Process (LAMP) from Missouri S&T is a laser based metals rapid manufacturing process that uses machining to improve the final part's surface finish. When free-form machining, the absence of enough deposited material results in inconsistent scallop heights which result in poor surface finish or incorrect geometry in the final part. This paper investigates a probabilistic approach to various uncertainties involved in the deposition and subsequent machining of an arbitrary part. Furthermore, this paper analyses the machine errors which makes the response of Scallop Height to exceed the predefined maximum scallop height when traveling along the tool …

Selective Laser Sintering Of 13-93 Bioactive Glass, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Mariano Garcia Velez

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Bioactive glasses are more promising than biopolymers in fabricating scaffolds for bone tissue repair because they convert to hydroxyapatite, when implanted in vivo. Both direct and indirect selective laser sintering (SLS) methods of 13-93 bioactive glass were considered in this research to study the feasibility of fabricating scaffolds for bone repair applications. Stearic acid was used as the binder in the indirect method to fabricate the scaffolds. The green scaffolds underwent binder burnout and sintering at various soaking conditions between 675⁰C and 700⁰C, achieving a maximum compressive strength of 23.6 MPa, which is higher than that of the human cancellous …

Selective Laser Sintering And Freeze Extrusion Fabrication Of Scaffolds For Bone Repair Using 13-93 Bioactive Glass: A Comparison, Krishna C. R. Kolan, Nikhil P. Doiphode, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

13-93 glass is a third-generation bioactive material which accelerates the bone’s natural ability to heal by itself through bonding with surrounding tissues. It is an important requirement for synthetic scaffolds to maintain their bioactivity and mechanical strength with a porous internal architecture comparable to that of a human bone. Additive manufacturing technologies provide a better control over design and fabrication of porous structures than conventional methods. In this paper, we discuss and compare some of the common aspects in the scaffold fabrication using two such processes, viz. selective laser sintering (SLS) and freeze extrusion fabrication (FEF). Scaffolds fabricated using each …

Computer Aided Contour Profiling Of High Strength Deposits, Sriram Praneeth Isanaka, Amar Bala Sridhar, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Additive manufacturing processes suffer from the effect of ripples, edge rounding and surface variations. To reduce their effect, ideal process parameters for the laser deposition process were investigated. Also, a new method was identified to analyze deposits by accurately plotting their contours. This was achieved through point cloud data of the deposits generated using coordinate measurement and 3D scanning. Curve fitting was performed on the data in Matlab to generate the contours of the deposit. The intercept values, heights, and contact angle of the curves give an indication of the uniformity of deposits and aid in reducing defects.

Effect Of Different Graphite Materials On Electrical Conductivity And Flexural Strength Of Bipolar Plates Fabricated By Selective Laser Sintering, Nannan Guo, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Graphite is an excellent material for bipolar plates used in Proton Exchange Membrane (PEM) fuel cell due to its great chemical resistance, but the brittle nature makes it difficult to manufacture. Selective Laser Sintering (SLS) based on layer-by-layer manufacturing technology can fabricate graphite bipolar plates with complex gas flow channels. To improve the performance of bipolar plates including electrical conductivity and flexural strength, different graphite materials (natural graphite, synthetic graphite, carbon black, and carbon fiber) were investigated to fabricate test samples. These samples then went through post processing including carbonization and infiltration. The results show that bipolar plates with electrical …

Freeze Extrusion Fabrication Of 13-93 Bioactive Glass Scaffolds For Bone Repair, Tieshu Huang, Nikhil D. Doiphode, M. N. Rahaman, Ming-Chuan Leu, B. Sonny Bal, D. E. Day

Materials Science and Engineering Faculty Research & Creative Works

There is an increasing demand for synthetic scaffolds with the requisite biocompatibility, internal architecture, and mechanical properties for the bone repair and regeneration. In this work, scaffolds of a silicate bioactive glass (13-93) were prepared by a freeze extrusion fabrication (FEF) method and evaluated in vitro for potential applications in bone repair and regeneration. The process parameters for FEF production of scaffolds with the requisite microstructural characteristics, as well as the mechanical and cell culture response of the scaffolds were evaluated. After binder burnout and sintering (60 min at 700°C), the scaffolds consisted of a dense glass network with interpenetrating …

Functionally Graded Materials By Laser Metal Deposition (Preprint), Syamala R. Pulugurtha, Joseph William Newkirk, Frank W. Liou, Hsin-Nan Chou

Materials Science and Engineering Faculty Research & Creative Works

Fabrication of functionally graded materials (FGMs) by laser metal deposition (LMD) has the potential to offer solutions to key engineering problems over the traditional metalworking techniques. But the issues that need to be addressed while building FGMs are intermixing in the layers and cracking due to the residual stresses. This paper is to present the study of the effect of process parameters (laser power and travel speed) on the degree of dilution between the substrate (or, previous layer) and powder material for few metallurgical systems.

Freeze Extrusion Fabrication Of 13-93 Bioactive Glass Scaffolds For Bone Repair, Nikhil D. Doiphode

Masters Theses

"We have investigated Freeze Extrusion Fabrication (FEF) of 13-93 bioactive glass to fabricate three dimensional scaffolds for bone tissue engineering. Bioactive glass paste was prepared for consistent extrusion through micro-nozzle and controlled porosity scaffolds were fabricated using additive manufacturing FEF. CAD models were prepared for different scaffold designs and computer controlled layer-by-layer deposition of pseudoplastic paste was carried out to in accordance. Liquid nitrogen assisted freezing of pastes was used for the consolidation of deposited layers. Post processing binder burnout and sintering schedules were designed for evaporation of organic binder and densification of glass. Sintering shrinkage was measured, and X-ray …

Mechanical Properties And Microstructure Study For Direct Metal Deposition Of 316l Stainless Steel, Tian Fu

Masters Theses

"Direct metal deposition or laser cladding is a process capable of producing fully dense and net shape metal products and this process could be used on coating metal components in various engineering applications. This process has fast heating and cooling rates which can improve the surface hardness and provide excellent adhesion through metallurgical bond between coating material and substrate. This paper evaluated the laser deposited 316L stainless steel coating on 4340 steel, which is widely used for aircraft landing gear applications. The microstructure, micro-hardness and quantitative EDS were explored to verify the coating properties. The desired homogeneous microstructure and high …

Quantification Of Product Color Preference In A Utility Function, Hannah L. Turner

Masters Theses

"Currently, many marketing and engineering tools exist to help a designer optimize quantitative attributes of a product, such as height, weight, volume, or cost. However, these methods cannot effectively take into consideration aesthetic attributes of a product, or any other attributes for which there is no understood functional relationship between the attribute's potential values and the consumer's preference. This research has begun the work of developing this necessary functional relationship for the aesthetic attribute of color and has created a methodology for further research. To do this, colors were represented by their red, green, and blue light components, and preference …

Design And Development Of Microwire Feeder For Laser Applications, Amogh J. Shenoy

Masters Theses

"This thesis focuses on the design and development of a microwire feeder for laser applications. The use of wire-feeders in laser welding and electrical discharge machining applications has been prominent which can handle wire of 0.25 mm and it can go up to 10.0 mm in other applications. Development of microwire handling devices is complicated and difficult due to its low buckling strength; the need for high accuracy for its use; and the harsh environment it is exposed to, in laser applications. This paper presents a systematic methodology for the design and development of a high-precision microwire handling device. This …

Maskless Additive Manufacturing Of Micro Structures By Laser Sintering Of Nanoparticles, Vivekram Ramanathan

Masters Theses

"The focus of this study was to investigate an alternate microfabrication process of sintering nanoparticles using a patterned laser light to generate two dimensional (2D) and three dimensional (3D) geometries. With trends of producing electronic and medical devices using cheaper and faster technologies, a new procedure was developed to deposit and bond miniature patterns of silver nanoparticles onto silicon substrates.

The process consists of spraying silver nanoparticles onto the substrate while a patterned or modulated laser beam is focused onto the sprayed nanoparticles. These nanoparticles exposed under the modulated laser light undergo partial melting or sintering and adhere to the …

Functionally Graded Materials By Laser Metal Deposition, Syamala Rani Pulugurtha, Joseph William Newkirk, Frank W. Liou, Hsin-Nan Chou

Materials Science and Engineering Faculty Research & Creative Works

Fabrication of functionally graded materials (FGMs) by laser metal deposition (LMD) has the potential to offer solutions to key engineering problems over the traditional metal-working techniques. But the issues that need to be addressed while building FGMs are intermixing in the layers and cracking due to the residual stresses. This paper is to present the study of the effect of process parameters (laser power and travel speed) on the degree of dilution between the substrate (or, previous layer) and powder material for few metallurgical systems.

Development Of Extrusion-On-Demand For Ceramic Freeze-Form Extrusion Fabrication, Thomas Oakes, Parimal Kulkarni, Robert G. Landers, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In the Freeze-form Extrusion Fabrication (FEF) process, extrusion-on-demand (EOD) refers to the ability to control the start and stop of paste extrusion on demand and is vital to the fabrication of parts with complex geometries. This paper describes the development of EOD for ceramic FEF through modeling and control of extrusion force, selection of appropriate process parameters, and a dwell technique for start and stop of extrusion. A general tracking controller with integral action is used to allow tracking of a variety of reference forces while accounting for the variability in the paste properties. Experiments are conducted to model the …

Fuel Cell Development Using Additive Manufacturing Technologies -- A Review, Nikhil P. Kulkarni, Gargi Tandra, Frank W. Liou, Todd E. Sparks, Jianzhong Ruan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Fuel cells are being perceived as the future clean energy source by many developed countries in the world. The key today for clean power is the reliance of fuel cells not only to power automobiles but also for residential, small commercial, backup power etc. which calls for production on a large scale. Additive manufacturing is perceived as a way to develop cost effective fuel cells. It imparts flexibility to design different kinds of fuel cells along with reduction in material wastage. This paper deals with the review of additive manufacturing processes for research and development of fuel cell components, such …

Increase Of Heat Transfer To Reduce Build Time In Rapid Freeze Prototyping, Ming-Chuan Leu, Sriram Praneeth Isanaka, Von Richards

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Reduction of part build time in the Rapid Freeze Prototyping (RFP) process, which fabricates a 3D ice part layer-by-layer by depositing and freezing water droplets, has been achieved by increase of heat transfer. Three mechanisms have been experimentally investigated: 1) cooling the substrate, 2) use of forced convection, and 3) use of a chilling plate. Cooling the substrate is effective for parts of small heights but becomes ineffective with increase in part height. Forced convection produced desirable reduction in part build time but with the undesirable formation of frost on the built ice part. The use of chilling plate to …

Development Of A Melt Pool Tracking Vision System For Laser Deposition, Todd E. Sparks, Lie Tang, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper chronicles the development of a vision system for tracking melt pool morphology in the laser metal deposition process. This development is to augment an existing temperature feedback control system. Monitoring both the temperature and shape of the melt pool is necessary because of the effects of local geometry on the cooling rate at the melt pool. Temperature feedback alone cannot accommodate this effect without complex process planning. The vision system's hardware, software, and integration into the laser deposition system's controller is detailed in this paper. Preliminary testing and the effects on depositionquality is also discussed.

Evaluation Of Direct Diode Laser Deposited Stainless Steel 316l On 4340 Steel Substrate For Aircraft Landing Gear Application, Tian Fu, Todd E. Sparks, Frank W. Liou, Joseph William Newkirk, Zhiqiang Fan, Syamala Rani Pulugurtha, Jianzhong Ruan, Hsin-Nan Chou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

300M steel is used extensively for aircraft landing gears because of its high strength, ductility and toughness. However, like other high-strength steels, 300M steel is vulnerable to corrosion fatigue and stress corrosion cracking, which can lead to catastrophic consequences in the landing gear. Stainless steels offer a combination of corrosion, wear, and fatigue properties. But for an aircraft landing gear application a higher surface hardness is required. A laser cladding process with fast heating and cooling rates can improve the surface hardness. AISI 4340 steel is used as a lower cost alternative to 300M due to its similar composition. In …

Development Of Extrusion On Demand For Ceramic Freeze-Form Extrusion Fabrication Processes, Parimal Sanjay Kulkarni

Masters Theses

"Freeze-form Extrusion Fabrication (FEF) is a Solid Freeform Fabrication method. It involves the deposition of a ceramic paste in a layer by layer manner to construct a three dimensional structure. The ceramic paste used in this process consists of a high solids loading of ceramic powder mixed with water and a nominal amount of an aqueous organic binder. These characteristics make the process environmentally friendly. Also the absence of dies or molds in the process makes it suitable for fabrication of materials like ceramics. In the past, parts have been fabricated with continuous extrusion of a ceramic paste. In FEF, …

Investigation Of Selective Laser Sintering Of Zirconium Diboride Parts, Shashwatashish Pattnaik

Masters Theses

"This research investigates the fabrication of three-dimensional parts from ZrB₂, an ultra high temperature ceramic (UHTC), using the selective laser sintering (SLS) process. Based on an experimental investigation, optimum values for the SLS parameters (scan speed, laser power, energy density, scan spacing and layer thickness), used on a DTM Sinterstation 2000, were determined to build green ZrB₂ parts with high integrity and sharp geometrical features. This was done by melting the polymer binder used to bond the ceramic particles layer-by-layer according to the cross-section of a CAD model. The use of a sacrificial plate to eliminate cracks in the bottom …

Freeform Fabrication Of Zirconium Diboride Parts Using Selective Laser Sintering, Ming-Chuan Leu, Erik B. Adamek, Tieshu Huang, Greg Hilmas, Fatih Dogan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using the Selective Laser Sintering (SLS) process, both flexural test bars and 3D fuel injector components have been fabricated with zirconium diboride (ZrB₂) powder. Stearic acid was selected as the binder. Values of SLS process parameters were chosen such that the green parts could be built with sharp geometrical features and that the sintered parts could have good mechanical properties. After binder burnout and sintering, the SLS fabricated ZrB₂ test bars achieved 80% theoretical density, and the average flexural strength of the sintered samples was 195 MPa. These values demonstrate the feasibility of the SLS process for …

Direct 3d Layer Metal Deposition, Jianzhong Ruan, Lie Tang, Todd E. Sparks, Robert G. Landers, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Multi-axis slicing for solid freeform fabrication (SFF) manufacturing processes can yield non-uniform thickness layers, or 3D layers. Using the traditional parallel layer construction approach to build such a layer leads to a staircase which requires machining or other post processing to form the desired shape. This paper presents a direct 3D layer deposition approach. This approach uses an empirical model to predict the layer thickness based on experimental data. The toolpath between layers is not parallel; instead, it follows the final shape of the designed geometry and the distance between the toolpath in the adjacent layers varies at different locations. …

Product Focused Freeform Fabrication Education, Frank W. Liou, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Presented in this paper is our experience of teaching freeform fabrication to students at the Missouri University of Science and Technology, and to high school students and teachers. The emphasis of the curriculum is exposing students to rapid product development technologies with the goal of creating awareness to emerging career opportunities in CAD/CAM. Starting from solid modeling, principles of freeform fabrication, to applications of rapid prototyping and manufacturing in industry sponsored product development projects, students can learn in-depth freeform fabrication technologies. Interactive course content with hands-on experience for product development is the key towards the success of the program.

Direct-To-Part Machining Waste Recycling Using Laser Metal Deposition, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser metal deposition typically uses metal powders as the build material of choice. The ability to reprocess waste materials using this technology would significantly reduce the material cost and cradle-to-grave energy content of parts produced using these methods. This capability will also greatly increase the utility of laser deposition, to potential industrial uses. This paper explores the usage of machining chips as an alternate source of build material. Topics covered include material handling, material preprocessing, and comparison to powder- based deposition.

Modeling And Experimental Results Of Concentration With Support Material In Rapid Freeze Prototyping, Frances D. Bryant, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Ice structures with complex geometries and overhung areas are created by the Rapid Freeze Prototyping (RFP) process in a sufficiently cool environment by freezing water into ice as the main material in conjunction with a eutectic dextrose-water solution as the sacrificial support material. The supported areas in an ice structure are removed via an increase in temperature in a separate environment after the structure is completely fabricated. To understand to what extent these two materials mix during fabrication, two methods of modeling the concentration changes that occur near the interface of the main and support materials have been developed. The …

Microstructural Characterization Of Diode Laser Deposited Ti-6al-4v, Tian Fu, Zhiqiang Fan, Syamala R. Pulugurtha, Todd E. Sparks, Jianzhong Ruan, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser Direct Metal Deposition (DMD) is an effective approach to manufacturing or repairing a range of metal components. The process is a layer-by-layer approach to building up a three dimensional solid object. The microstructure influences mechanical properties of the deposited parts. Thus, it is important to understand the microstructural features of diode laser deposited parts. This paper presents a microstructure analysis of a diode laser deposited Ti-6Al-4V onto a Ti-6Al-4V substrate. laser deposited parts. This paper presents a microstructure analysis of a diode laser deposited Ti-6Al-4V onto a Ti-6Al-4V substrate.

Layer-To-Layer Height Control For Laser Metal Deposition Processes, Lie Tang, Jianzhong Ruan, Todd E. Sparks, Robert G. Landers, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A Laser Metal Deposition (LMD) height controller design methodology is presented in this paper. The height controller utilizes the Particle Swarm Optimization (PSO) algorithm to estimate model parameters between layers using measured temperature and track height profiles. The process model parameters for the next layer are then predicted using Exponentially Weighted Moving Average (EWMA). Using the predicted model, the powder flow rate reference profile, which will produce the desired layer height reference, is then generated using Iterative Learning Control (ILC). The model parameter estimation capability is tested using a four-layer deposition. The results demonstrate the simulation based upon estimated process …