Manufacturing Commons^™

Vision-Based Process Monitoring For Laser Metal Deposition Processes, Sreekar Karnati, Niroop Matta, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser Metal deposition is a process with immense scope and promise for becoming a robust manufacturing technology in the near future. Monitoring process variables is very instrumental in process planning and output monitoring. The current work deals with realizing the effect of power modulation on size of the high temperature region during deposition with varying powder feed. A thermal camera was used to visualize and analyze the deposition process. The area of the high temperature region through the deposition was identified and compared to realize the effect of each variable parameter during deposition. The power modulation was fruitful in modulating …

Paste Development And Co-Sintering Test Of Zirconium Carbide And Tungsten In Freeze-Form Extrusion Fabrication, Ang Li

Masters Theses

"Ultra-high temperature ceramics are being investigated for future use in aerospace applications due to their superior thermo-mechanical properties, as well as oxidation resistance, at temperatures above 2000°C. However, their brittle properties make them susceptible to thermal shock failure. Components fabricated as functionally graded materials (FGMs) can combine the superior properties of ceramics with the toughness of an underlying refractory metal by fabricating graded composites. This paper discusses the grading of two materials through the use of a Freeze-form Extrusion Fabrication (FEF) system to build FGMs parts consisting of zirconium carbide (ZrC) and tungsten (W). Aqueous-based colloidal suspensions of ZrC and …

Part Height Control Of Laser Metal Additive Manufacturing Process, Yu-Herng Pan

Masters Theses

"Laser Metal Deposition (LMD) has been used to not only make but also repair damaged parts in a layer-by-layer fashion. Parts made in this manner may produce less waste than those made through conventional machining processes. However, a common issue of LMD involves controlling the deposition's layer thickness. Accuracy is important, and as it increases, both the time required to produce the part and the material wasted during the material removal process (e.g., milling, lathe) decrease. The deposition rate is affected by multiple parameters, such as the powder feed rate, laser input power, axis feed rate, material type, and part …

Parameter Optimization For Controlling Aluminum Loss When Laser Depositing Ti-6al-4v, Richard Charles Barclay

Masters Theses

"The ability to predict the mechanical properties of engineering materials is crucial to the manufacturing of advanced products. In the aerospace industry, Ti-6Al-4V is commonly used to build structures. Any deviation from the alloy's standard properties can prove detrimental. Thus, the compositional integrity of the material must be controlled. The ability to directly build and repair large, complicated structures directly from CAD files is highly sought after. Laser Metal Deposition (LMD) technology has the potential to deliver that ability. Before this process can gain widespread acceptance, however, a set of process parameters must be established that yield finished parts of …

Development Of A Postprocessor For A Multi-Axis Cnc Milling Center, Mihir Satish Adivarekar

Masters Theses

"Most of the current college design and manufacturing curricula are primarily focused on computer aided design (CAD), while less emphasis is given to computer aided manufacturing (CAM). A great opportunity has been missed as the benefits of CAD/CAM cannot then be fully learned. Postprocessor plays a vital role in integration of CAD//CAM with computer numerically controlled (CNC) machines. Hence, postprocessor must be developed accurately. This thesis is composed of one paper. Paper I proposes a novel methodology to determine compensation vectors for the post processor of multi-axis milling center. The new approach that has been implemented in Paper I involves …

Development Of A New Temporary Fastener For Aerospace Automation, Xiangwen Zhang

Masters Theses

"Temporary fasteners are required in aircraft assembly, especially in the assembly of wings, fuselage, and aircraft skin's substructure prior to drilling holes for permanent fasteners by automated drilling machines. The objective was to develop a temporary fastener that can be installed, clamped, loosened, and removed from one side with a short head length. Published papers, web pages and patents relating to temporary fasteners were reviewed. Then by considering the ability to meet the operation requirements and concerns, a temporary fastener was designed with the following advantages:

• a simple structure that can be easily fabricated
• a short head length to save …

Freeze-Form Extrusion Fabrication Of Functionally Graded Material Composites Using Zirconium Carbide And Tungsten, Ang Li, Aaron S. Thornton, Bradley K. Deuser, Jeremy Lee Watts, Ming-Chuan Leu, Greg Hilmas, Robert G. Landers

Materials Science and Engineering Faculty Research & Creative Works

Ultra-high-temperature ceramics are being investigated for future use in aerospace applications due to their superior thermo-mechanical properties, as well as their oxidation resistance, at temperatures above 2000⁰C. However, their brittleness makes them susceptible to thermal shock failure. As graded composites, components fabricated as functionally-graded materials (FGMs) can combine the superior properties of ceramics with the toughness of an underlying refractory metal. This paper discusses the grading of two materials through the use of a Freeze-form Extrusion Fabrication (FEF) system to build FGM parts consisting of zirconium carbide (ZrC) and tungsten (W). Aqueous-based colloidal suspensions of ZrC and W were developed …

The Applications Of Additive Manufacturing Technologies In Cyber-Enabled Manufacturing Systems, Sriram Praneeth Isanaka, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The application of networked sensors and control in various areas, such as smart grids and infrastructures, has become a recent trend, called cyber-physical systems. The Cyber Enabled Manufacturing (CEM) environment is to apply these technologies in manufacturing systems to handle a significantly greater magnitude of manufacturing data. Additive manufacturing techniques print or place material layer by layer to form a part, thus have a great potential to help accelerate CEM process by printing or embedding sensors and actuators in the proper locations. This paper summarizes the roles of additive manufacturing technologies to help establish a CEM environment.

Interactions Of An Additive Manufacturing Program With Society, Frank W. Liou, Ming-Chuan Leu, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Additive Manufacturing (AM) has shown considerable promise for the future but also proposes some challenges. Many AM barriers tend to be non-technical and instead are human-centric issues such as lack of education of practitioners in AM capabilities, cultural differences, vested interests, and potentially lack of imagination. It is highly desirable for all research and educational institutions to help address these issues. This paper summarizes the additive manufacturing research and education program at the Missouri University of Science and Technology (Missouri S&T) and its interactions with various constituents, including K-12 students, undergraduate and graduate students, distance students, and industry.

Experimental Study Of Polymer Electrolyte Membrane Fuel Cells Using A Graphite Composite Bipolar Plate Fabricated By Selective Laser Sintering, Nannan Guo, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Selective Laser Sintering (SLS) can be used to fabricate graphite composite bipolar plates with complex flow fields for Polymer Electrolyte Membrane (PEM) fuel cells. The additive manufacturing process can significantly reduce the time and cost associated with the research and development of bipolar plates as compared to other fabrication methods such as compression molding. In this study, bipolar plates with three different designs, i.e., parallel in series, interdigitated, and bio-inspired, were fabricated using the SLS process. The performance of these SLS-fabricated bipolar plates was studied experimentally within a fuel cell assembly under various operating conditions. The effect of temperature, relative …

Comparison Of Compression Molding And Selective Laser Sintering Processes In The Development Of Composite Bipolar Plates For Proton Exchange Membrane Fuel Cells, Ehsan Taghipour, Ming-Chuan Leu, Nannan Guo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Bipolar plates are key components of Proton Exchange Membrane (PEM) fuel cells. They carry current away from the cell and withstand the clamping force of the stack assembly. Therefore, PEM fuel cell bipolar plates must have high electrical conductivity and adequate mechanical strength, in addition to being light weight and low cost in terms of both applicable materials and production methods. In order to attain these goals, we have manufactured graphite-carbon- polymer composite plates using Compression Molding (CM), which is suitable for mass production, and Selective Laser Sintering (SLS), which is suitable for making prototypes. In this paper, the electrical …

Modeling, Analysis And Simulation Of Paste Freezing In Freeze-Form Extrusion Fabrication, Mingyang Li, Robert G. Landers, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

During the freeze-form extrusion fabrication process for aqueous-based pastes, the sub-zero temperature environment aids the part in maintaining its shape by freezing the water present in the paste. The paste freezes very quickly when deposited on a substrate in a freezing environment. However, as the part’s height increases, the freezing time increases as the heat conduction rate to the substrate decreases. The freezing time can exceed the time required to extrude one layer of paste due to water’s high latent heat, thus leaving the extruded paste in its semi-liquid state and causing the part to deform or even collapse. Therefore, …

Fabrication Of Complex Ceramic Parts With Sacrificial Material Using Freeze-Form Extrusion Fabrication, Diego Armando Garcia MontañO

Masters Theses

"An additive manufacturing process called Freeze-form Extrusion Fabrication (FEF) was developed in this study to fabricate complex ceramic parts that require the use of sacrificial materials. The aqueous paste of alumina (Al₂O₃) was used as the main material, with solids loadings as high as 50 vol. % and water as the main liquid medium. Methyl cellulose, with a 10 vol. % solids loading and 90 vol. % water content, was used as the sacrificial material. The freeze-form extrusion machine has multiple extruders (extrusion devices) capable of fabricating parts from multiple materials without mixing them. The dynamic process of extruding alumina …

Generic Kinematic Simulation For Verification Of Laser Deposition Tool Paths, Sweta Dhaveji Chakravadhanula

Masters Theses

"The development of 3D visual simulation tool for machine simulation is a key approach in saving time and reducing cost. It is an important step before a manufacturing operation is performed on a part, as a tool to detect collision and validate the operation results. There are several kinds of manufacturing equipment being used and hence there is a need for the development of a generalized method to visually simulate a variety of machines. This paper presents the research conducted on describing machine configuration in a generic format which not only gives useful information, but can also be used as …

5-Axis Tool Path Generation With Collision Detection For Finish Machining Of Freeform Surfaces, Jomy Francis

Masters Theses

"Research in the field of Tool path generation for freeform surfaces has been done intensively in the past. However, the main challenge that still exists is the computational efficiency related to the tool path generation. Tool path generation for freeform surface involves instantaneous calculation of new tool orientations which does not collide with the neighboring surfaces. Since the collision check of tool and neighboring surface is done repetitively at every instant of the tool, the calculations at every instant are to be computationally as easy as possible.

This thesis is composed of one paper. Paper I presents a novel extension …

Development Of A Technique For Testing Of Tensile Properties With Miniature Size Specimens For Metal Additive Manufacturing, Sujitkumar Dongare

Masters Theses

"The study of mechanical properties of metals provides a basis to decide on the capability of a particular metal for a task and also to make predictions about its life. The concepts of stress, strain and strength of materials are employed in practically every engineering discipline. Mechanical properties such as stiffness, yield strength, tensile strength, ductility, toughness, impact resistance, creep resistance, fatigue resistance and others, influence the design, fabrication and service life of equipment. Therefore, more than one property is considered for the material selection process for an application. For complete understanding of any material and its feasibility for a …

A Planning Tool To Predict The Welding Angle In Laser Metal Deposition, Sriram Prabhu

Masters Theses

"Research in Laser Metal Deposition (LMD) has been done rigorously in the past. However, the main challenge that still exists is the production of complex part geometries having overhang features. Production of such features requires individual tracks with a high aspect ratio and wider bead angle. The use of destructible/ non-destructible support structures involves costly post production operations which increase production cost. Tilting or moving the deposition surface can be useful to create overhangs but are applicable only to special cases. Since such techniques have to be used by the manufacturing community, the techniques need to be simple in calculation …

Effect Of Particle Size, Binder Content And Heat Treatment On Mechanical Properties Of 13-93 Bioactive Glass Scaffolds, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Mariano Garcia Velez

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Particle size, binder content and the post-processing schedule are important parameters that affect the microstructure, and, hence, the mechanical properties of parts produced using the indirect selective laser sintering process. 13-93 bioactive glass, with mean particle sizes ranging from 10 μm to 44 μm, is mixed with different amounts of stearic acid binder to fabricate green scaffolds. Through the design of the post-processing schedule, the time required for postprocessing the green scaffolds is reduced from the initial 80 hrs to 12 hrs. The compressive strength varies from 41 MPa for a part with~60% porosity to 157 MPa for a part …

Freeze-Form Extrusion Fabrication Of Composite Structures, Ming-Chuan Leu, Lie Tang, Bradley K. Deuser, Robert G. Landers, Greg Hilmas, Shi C. Zhang, Jeremy Lee Watts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A Freeze-form Extrusion Fabrication (FEF) process capable of making three-dimensional (3D) parts and structures with graded composite materials is presented in this paper. The process development includes the design and manufacture of a gantry machine with a triple-extruder mechanism and the associated electronics hardware and computer software for fabricating functionally graded parts from multiple aqueous pastes. A rheological behavior study with Al₂O₃ paste is performed to identify an efficient binder for transforming the paste into a pseudoplastic with a high yield stress. A green part is first fabricated using the triple-extruder FEF machine in a layer-by-layer manner …

Bio-Inspired Design Of Bipolar Plate Flow Fields For Polymer Electrolyte Membrane Fuel Cells, Nannan Guo, Ming-Chuan Leu, Maoliang Wu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The flow field of a bipolar plate distributes hydrogen and oxygen for polymer electrolyte membrane (PEM) fuel cells and removes the produced water from the fuel cells. It greatly influences the performance of fuel cells, especially regarding reduction of mass transport loss. Flow fields with good gas distribution and water removal capabilities reduce the mass transport loss, thus allowing higher power density. Inspired by natural structures such as veins in tree leaves and blood vessels in lungs, which efficiently feed nutrition from one central source to large areas and are capable of removing undesirable by-products, a mathematic model has been …

Numerical Simulation Of Ram Extrusion Process For Ceramic Materials, Mingyang Li, Lie Tang, Fei Xue, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The freeze–form extrusion process for aqueous-based ceramic paste is complex due to the non-Newtonian behavior of the paste. In this paper the process is studied numerically using a developed mathematical model. The ceramic paste viscosity is characterized by the Herschel-Bulkley model. The relationship between plunger velocity and extrusion force is computed numerically. The influence of air, which is mixed with the paste during the loading process, is also examined. Due to the compressibility introduced by the trapped air, the plunger force dynamic response is typically dominated by a first order response. It is also shown that the extrusion plunger force …

A Strategy For Fabricating Complex Structures Via A Hybrid Manufacturing Process, Tarak A. Amine, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The purpose of this paper is to introduce a strategy for fabricating complex structures via a hybrid manufacturing process. The Laser Aided Manufacturing Process (LAMP) lab at Missouri S&T has developed a hybrid process combining both a direct metal deposition process and a five-axis CNC milling. Accessibility is a difficulty when finish machining internal features. The concept is to pause the deposition process to finish machine an internal feature while it is still visible is one possible solution to this issue. However, this must be done in a manner that will not be spoiled when the deposition process continues. This …

Octree Approach For Simulation Of Additive Manufacturing Toolpath, Ch. Sweta Dhaveji, Todd E. Sparks, Jianzhong Ruan, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Machine simulation is an effective way of checking additive manufacturing tool paths for both interferences and errors in part produced. This paper presents an algorithm to visually simulate a multi axis additive manufacturing system as it executes a process plan. Simulation results are intended to be used as a verification step before physically producing the part. Verification is particularly important for large builds of expensive materials. The algorithm uses an octree approach to efficiently model the deposition of part geometry and its changes. This paper discusses development of the simulation algorithm, including both the representation of the additive manufacturing machine …

Process Planning And Control For Functionally Graded Material Fabrication Using Freeze-Form Extrusion Fabrication, Brad Deuser, Lie Tang, Jeff Geldmeier, Robert G. Landers, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using multiple materials in additive manufacturing technologies is critical for building parts with functionally gradient geometries. In order to achieve a desired material gradient, an advanced process planning and control system is required. This paper details the development of a process planning method and control system for functionally graded material fabrication using a triple extruder Freeze-form Extrusion Fabrication (FEF) system including motion code generation, extruder dynamic modeling and control, and composition gradient control. The effect that extruding multiple materials from a single orifice via static mixing has on the time delay of the resulting mixture is taken into account for …

Development Of Virtual Engineering Simulation For Lean Education, Akalpit Kiran Gadre

Masters Theses

"Global competition and customer demands are pressing modern industry operations to become leaner. The race among the global corporations to "go lean" demands engineers with an in-depth understanding of lean philosophies. An overview of current methods for teaching lean shows that they include small scale hands-on projects, presentations, and guest lectures. There is a need to incorporate a more immersive virtual simulation to further inspire students. Many lean simulation games are available in the market; however, they lack simplicity, ability to store the results, and modeling power.

The goal of this research is to develop a virtual simulation platform, enabling …

Innovative Air Breathing Design And Output Control For Portable Proton Exchange Membrane Fuel Cell, Amar Bala Sridhar

Masters Theses

"Proton Exchange Membrane (PEM) Fuel Cell Technology is an energy source that can provide several times more energy per unit volume than current lithium ion batteries that are available in the market today. The barriers that exist that prevent the fuel cell from entering the world of portable applications are mainly system architecture integration. The idea is to have a fully functioning fuel cell with optimum power output using an innovative chimney design. Tests were conducted to quantify the advantage of using a chimney with the fuel cell. Further research was done to shed light on how different chimney designs …

Analysis And Modeling Of Depth-Of-Cut During End Milling Of Deposited Material, Haythem Gaja

Masters Theses

"This study addresses depth-of-cut detection and tool-workpiece engagement using an acoustic emission monitoring system during milling machining for a deposited material. Online detection of depth-of-cut presents many technical difficulties. Researchers have used various types of sensors and methods to assess the depth-of-cut and surface errors. Due to the strong correlation between acoustic emission and cutting depth during the depth end milling process, it is useful to forecast the depth-of-cut from the acoustic emission signal. This work used regression analysis to model and detect the depth-of-cut. The experiments were carried out on a Fadal vertical 5-Axis computer numerical control machine using …

Development Of Lower Cost Imaging Systems For Laser Metal Deposition Process, Shyam Barua

Masters Theses

"Laser Metal Deposition (LMD) has been used as an additive manufacturing process in industries such as aerospace and die castings. LMD is especially useful in repair applications involving die repair. However, it is still not used widely in industry due to variations in the quality of parts. There are multiple interactions between various factors which influence the quality of deposit.

There exists a need for defect detection systems to detect any changes in the deposition quality during deposition. On demand detection enables adjustment in process parameters and minimization of rework cost.

Vision systems have been used extensively in the industry …

Mea Manufacturing Using An Additive Manufacturing Process To Deposit A Catalyst Pattern In An Mea And Its Impact On Cost Reduction, Nikhil P. Kulkarni, Todd E. Sparks, Gargi Tandra, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The manufacturing of a fuel cell Membrane Electrode Assembly (MEA) is a significant cost driver in polymer-electrolyte membrane (PEM) fuel cell technologies, primarily due to the inclusion of expensive materials in the catalyst layer. The selective deposition of a catalyst on the MEA of a fuel cell can drastically reduce the costs depending upon the catalyst, method used for deposition, and production volume. In this paper, testing and analysis of a novel catalyst iridium oxide is discussed. The performance of the catalyst will be compared with the conventional catalysts which will give us an estimate of its effectiveness however, in …

Laser Based Rapid Manufacturing Of Metallic Gas Diffusion Layers For Pem Fuel Cells, Gargi Tandra, Todd E. Sparks, Shyam Barua, Nikhil P. Kulkarni, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Gas Diffusion layers (GDL’s) are an essential component of Polymer Electrolyte Membrane Fuel cells (PEMFC’s) which aid in thermal & electrical conductivities, water management and act as backup layers for the membrane electrode assemblies. This paper summarizes the effort to prototype metallic GDL designs using a miniature laser deposition system developed at Missouri University of Science & Technology. The pore sizes are controlled by masking the diverging laser beam using stainless steel masks of varying sizes and shapes. The through pore feature and further treatment of the GDL’s for hydrophobicity reduces the water management issue and thereby increases the performance …