Mechanical Engineering Commons^™

Study Of Role Of Meniscus And Viscous Forces During Liquid-Mediated Contacts Separation, Prabin Dhital

All Graduate Theses, Dissertations, and Other Capstone Projects

Menisci may form between two solid surfaces with the presence of an ultra-thin liquid film. When the separation operation is needed, meniscus and viscous forces contribute to an adhesion leading stiction, high friction, possibly high wear and potential failure of the contact systems, for instance microdevices, magnetic head disks and diesel fuel injectors. The situation may become more pronounced when the contacting surfaces are ultra-smooth and the normal load is small. Various design parameters, such as contact angle, initial separation height, surface tension and liquid viscosity, have been investigated during liquid-mediated contact separation. However, how the involved forces will change …

Finite Element Simulation Of Single-Lap Shear Tests Utilizing The Cohesive Zone Approach, Wilson A. Perez

Honors Undergraduate Theses

Many applications require adhesives with high strength to withstand the exhaustive loads encountered in regular operation. In aerospace applications, advanced adhesives are needed to bond metals, ceramics, and composites under shear loading. The lap shear test is the experiment of choice for evaluating shear strength capabilities of adhesives. Specifically during single-lap shear testing, two overlapping rectangular tabs bonded by a thin adhesive layer are subject to tension. Shear is imposed as a result. Debonding occurs when the shear strength of the adhesive is surpassed by the load applied by the testing mechanism. This research develops a finite element model (FEM) …

Silver Nanoparticles Supported On Carbon Nanotube Carpets: Influence Of Surface Functionalization, Anil K. Karumuri, Dhawal P. Oswal, Heather A. Hostetler, Sharmila M. Mukhopadhyay

Mechanical and Materials Engineering Faculty Publications

The effectiveness of nanoparticle-based functional devices depends strongly on the surface morphology and area of the support. An emerging powerful approach of increasing the available surface area without decreasing strength or increasing bulk is to attach arrays of suitable nanotubes on the surface, and to attach the necessary nanoparticles to them. Earlier publications by this team have shown that carpet-like arrays of carbon nanotubes (CNTs) can be successfully grown on a variety of larger carbon substrates such as graphite, foams and fabric, which offer hierarchical multiscale supporting architecture suitable for the attachment of silver nanoparticles (AgNPs). A limiting factor of …

High Temperature Mechanics Of Aerospace Ceramic Composites Via Synchrotron Radiation, Albert Manero Ii

Electronic Theses and Dissertations

This research investigates the mechanics of complex aerospace material systems designed for extreme environments. Ceramics and ceramic matrix composites (CMCs) provide highly sought-after capabilities including the potential to withstand extreme temperatures and heat fluxes, severe oxidation and mechanical stresses. Two important material systems form the basis of the scope for this effort: i) thermal barrier coatings (TBCs) on Ni-superalloys that have enabled dramatic increases in turbine inlet temperatures exceeding 1100°C; and ii) ceramic matrix composites that have shown capability and promise for hypersonic applications beyond 1300°C. Understanding the mechanical and material properties of these materials as they evolve with temperature …

A Parametric Study Of Meso-Scale Patterns For Auxetic Mechanical Behavior Optimization, Matthew C. Schuler

Honors Undergraduate Theses

This thesis focuses on the development, parameterization and optimization of a novel meso-scale pattern used to induce auxetic behavior, i.e., negative Poisson's ratio, at the bulk scale. Currently, the majority of auxetic structures are too porous to be utilized in conventional load-bearing applications. For others, manufacturing methods have yet to realize the meso-scale pattern. Consequently, new auxetic structures must be developed in order to confer superior thermo-mechanical responses to structures at high temperature. Additionally, patterns that take into account manufacturing limitations, while maintaining the properties characteristically attached to negative Poisson's Ratio materials, are ideal in order to utilize the potential …

Heat Transfer And Pressure Measurements From Jet Array Impingement Onto A Large Radius Curved Surface, John Harrington

Electronic Theses and Dissertations

This study investigates the heat transfer and pressure drop characteristics of jet array impingement in two distinct parts. In the first part, the performance of a uniform array of jets on both a flat and a large radius curved target surface are compared. This comparison was done at average jet Reynolds number ranging from 55,000 to 125,000. In the second part, the characteristics of a non-uniform array of jets, more typical of geometries used in actual gas turbine combustors, are investigated, including the effects of the removal of downstream rows and the placement of rib features onto the target surface. …

Transient Cfd Analysis Of Autorotation Using Hybrid Les And Adaptive Mesh Morphing Techniques, Patricia Coronado Domenge

Electronic Theses and Dissertations

Large-Eddy Simulation (LES) based turbulence modeling is a developing area of research in Fluid-Structure Interaction (FSI). There is considerable scope for further scientific research in this field and this dissertation aims to extend it to the study of flow-induced motion. The emphasis of this work is on autorotation, an important category of flow-induced motion that is commonly seen in energy applications such as wind turbines and in aviation applications such as the autogyro. In contrast to existing works on FSI that typically assume prescribed motion of structures in a flow field, this research develops LES based FSI studies for large-scale …

Drops In 2d, Said Shakerin

All Faculty Articles - School of Engineering and Computer Science

No abstract provided.

3d Infrastructure Condition Assessment For Rail Highway Applications, Teng Wang

Theses and Dissertations--Civil Engineering

Highway roughness is a concern for both the motoring public and highway authorities. Roughness may even increase the risk of crashes. Rail-highway grade crossings are particularly problematic. Roughness may be due to deterioration or simply due to the way the crossing was built to accommodate grade change, local utilities, or rail elevation. With over 216,000 crossings in the US, maintenance is a vast undertaking. While methods are available to quantify highway roughness, no method exists to quantitatively assess the condition of rail crossings. Conventional inspection relies on a labor-intensive process of qualitative judgment. A quantifiable, objective and extensible procedure for …

Modeling And Control Of Fuel Cell-Battery Hybrid Energy Sources, Nima Lotfi

Doctoral Dissertations

"Environmental, political, and availability concerns regarding fossil fuels in recent decades have garnered substantial research and development in the area of alternative energy systems. Among various alternative energy systems, fuel cells and batteries have attracted significant attention both in academia and industry considering their superior performances and numerous advantages. In this dissertation, the modeling and control of these two electrochemical sources as the main constituents of fuel cell-battery hybrid energy sources are studied with ultimate goals of improving their performance, reducing their development and operational costs and consequently, easing their widespread commercialization. More specifically, Paper I provides a comprehensive background …

Smart Tail-Light System, Julia Wood, Donald G. Haiss

Williams Honors College, Honors Research Projects

According to the National Highway Traffic Safety Administration (NHTSA) Safety Vehicle Research, 29% of all vehicle accidents are rear end collisions. Many are a result of failure to respond to a slowing or stopped vehicle. [1] The purposed LED rear lighting system will incorporate attention getting techniques to increase vehicle visibility to other drivers. Due to the small size and stature of the 2015 human powered vehicle called Joey, it will be out of the ordinary when traveling on roadways. “Three in four (72%) bicyclists who rode after dark said they tried to do something to make themselves more visible.” …

Shock Tube And Mid-Infrared Laser Absorption Measurements Of Ignition Delay Times And Species Time-Histories, Batikan Koroglu

Electronic Theses and Dissertations

Energy consumption has increased dramatically as the world advances and becomes more industrialized. Over the next twenty five years, the U.S. Department of Energy expects the energy demand to increase by 29% with majority of the new energy coming from natural gas (methane). Another promising fuel source for power generation and transportation is the biofuels. The biofuel use in the US is shown to have increased substantially in the last decade. There are serious environmental concerns associated with greenhouse (e.g. carbon-dioxide) and toxic gas emissions (e.g. nitrogen oxides and aldehydes such as propanal) due to deriving energy from natural gas …

Experimental And Numerical Investigation Of Aerodynamic Performance For Vertical-Axis Wind Turbine Models With Various Blade Designs, Travis E. Salyers

College of Graduate Studies: Theses & Dissertations

The demand for wind energy as a renewable source is rising substantially. A growing interest exists in utilizing potential energy conversion applications in areas with less powerful and less consistent wind conditions. In these areas, vertical-axis wind turbines (VAWTs) possess several advantages over the conventional horizontal-axis type. Savonius turbines are drag-based rotors which operate due to a pressure difference between the advancing and retreating blades. These turbines are simpler in design, less expensive to install, non-dependent of wind direction, and more efficient in lower wind speeds. In the present study, six different rotor designs with equal swept areas are analyzed …

Enhancing Project Management With Lean World Class Manufacturing In Construction, Jacob Randles

College of Graduate Studies: Theses & Dissertations

In construction, the goal of commercial projects is to turn a profit. This is achieved by minimizing inputs and maximizing outputs while building a product that meets the customer’s perception of value. Value is determined through pre-negotiated specifications, plans, and material quality. Even in U.S. military construction, the unit executing the construction wants to complete the task on time and on budget, which can be difficult to do. Studies on project completion showcase a surprisingly high rate of failure in reaching the aforementioned “on time, on budget” goal. It is important to understand the nuances and details of U.S. Army …

Efficiency Evaluation Of A Magnetically Driven Multiple Disk Centrifugal Blood Pump, Kayla H. Moody

Theses and Dissertations

Heart failure is expected to ail over 8 million people in America by 2030 leaving many in need of cardiac replacement. To accommodate this large volume of people, ventricular assist devices (VADs) are necessary to provide mechanical circulatory support. Current VADs exhibit issues such as thrombosis and hemolysis caused by large local pressure drops and turbulent flow within the pump. Multiple disk centrifugal pumps (MDCPs) use shearing and centrifugal forces to produce laminar flow patterns and eliminate large pressure drops within the pump which greatly reduce risks that are in current VADs. The MDCP has a shaft drive system (SDS) …

Power Maximization For Pyroelectric, Piezoelectric, And Hybrid Energy Harvesting, Murtadha A. Shaheen

Theses and Dissertations

The goal of this dissertation consists of improving the efficiency of energy harvesting using pyroelectric and piezoelectric materials in a system by the proper characterization of electrical parameters, widening frequency, and coupling of both effects with the appropriate parameters.

A new simple stand-alone method of characterizing the impedance of a pyroelectric cell has been demonstrated. This method utilizes a Pyroelectric single pole low pass filter technique, PSLPF. Utilizing the properties of a PSLPF, where a known input voltage is applied and capacitance C_p and resistance R_p can be calculated at a frequency of 1 mHz to 1 Hz. …

Ionic And Electronic Conductivities Of Atomic Layer Deposition Thin Film Coated Lithium Ion Battery Cathode Particles, Rajankumar L. Patel, Jonghyun Park, Xinhua Liang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

It is imperative to ascertain the ionic and electronic components of the total conductivity of an electrochemically active material. A blocking technique, called the “Hebb-Wagner method”, is normally used to explain the two components (ionic and electronic) of a mixed conductor, in combination with the complex ac impedance method and dc polarization measurements. CeO₂ atomic layer deposition (ALD)-coated and uncoated, LiMn₂O₄ (LMO) and LiMn_1.5Ni_0.5O₄ (LMNO) powders were pressed into pellets and then painted with silver to act as a blocking electrode. The electronic conductivities were derived from the currents obtained using …

Silicon-Wall Interfacial Free Energy Via Thermodynamics Integration, Wan Shou, Heng Pan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We compute the interfacial free energy of a silicon system in contact with flat and structured walls by molecular dynamics simulation. The thermodynamics integration method, previously applied to Lennard-Jones potentials [R. Benjamin and J. Horbach, J. Chem. Phys. 137, 044707 (2012)], has been extended and implemented in Tersoff potentials with two-body and three-body interactions taken into consideration. The thermodynamic integration scheme includes two steps. In the first step, the bulk Tersoff system is reversibly transformed to a state where it interacts with a structureless flat wall, and in a second step, the flat structureless wall is reversibly transformed into an …

Effect Of Powder Particle Size On The Fabrication Of Ti-6al-4v Using Laser Metal Deposition From Elemental Powder Mixture, Xueyang Chen, Lei Yan, Wei Li, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Direct LMD (laser metal deposition) was used to fabricate thin-wall Ti-6Al-4V using the powder mixture of Ti-6 wt.%Al-4 wt.%V. SEM (scanning electron microscopy), OM (optical microscopy) and EDS (energy dispersive spectroscopy) were employed to examine the chemical composition and microstructure of the as-deposited sections. Vickers hardness tests were then applied to characterize the mechanical properties of the deposit samples which were fabricated using pre-mixed elemental powders. The EDS line scans indicated that the chemical composition of the samples was homogenous across the deposit. After significant analysis, some differences were observed among two sets of deposit samples which varied in the …

The Coupled Photothermal Reaction And Transport In A Laser Additive Metal Nanolayer Simultaneous Synthesis And Patterning For Flexible Electronics, S. Tsai, Y. Liu, Heng Pan, C. Liu, M. Lee

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Decomposition Of A Double Salt Ionic Liquid Monopropellant On Heated Metallic Surfaces, Steven P. Berg, Joshua L. Rovey

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A monopropellant consisting of 59% hydroxylammonium nitrate and 41% 1-ethyl-3-methylimidazolium ethyl sulfate by mass is tested for decomposition on heated platinum, rhenium, and titanium surfaces. It was found that the propellant decomposes at 165 °C on titanium, which is the decomposition temperature of HAN. The onset temperature for decomposition on platinum was 85 °C and on rhenium it was 125 °C. This suggests that platinum and rhenium act as catalysts for the decomposition of the monopropellant. From the experimental data, Arrhenius-type reaction rate parameters were calculated. The activation energy for platinum was 3 times less than that of titanium suggesting …

Observation Of Late-Time Ablation In Electric Solid Propellant Pulsed Microthrusters, Matthew S. Glascock, Joshua L. Rovey, Shae Williams, Jason Thrasher

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric solid propellants are an interesting potential option for propulsion because they are ignited by an applied electric current. The electric nature of these materials leads to the capability for use in pulsed electric propulsion devices. In this work, the ablation process of an electric solid propellant during pulsed micro thruster operation is investigated using a triple Langmuir probe, thrust stand and high-speed video camera. Results include quantitative time-of-flight, ablation mass per pulse and impulse-per-pulse measurements. Additionally, qualitative images from the high-speed video are temporally correlated to these measurements. Analyses indicate 45±11% of the ablated mass per pulse is expelled …

Fiber Orientation Prediction And Strength Evaluation Of Composite Spur Gears Reinforced By Discontinuous Fiber, Nawrin Jahan

Electronic Theses and Dissertations

Composite materials have been extensively used for their important role in attenuation of components design, low specific weight, high mechanical performance, and excellent corrosion resistance offer significant advantages over metallic materials. These superlative properties can be attained by tailoring different material in an appropriate combination of the reinforcing phase (carbon fiber, alumina, etc.) and matrix phase (polymer, ceramic, metals, etc.). Carbon fiber reinforced composites are mostly used on intricate stress sensitive structures like wings of aero plane or gear. Amount of fiber, fiber type, and size of the fiber and the orientation of reinforcing fibers directly influence the mechanical properties …

Effects Of Defects On The Performance Of Hierarchical Honeycomb Metamaterials Realized Through Additive Manufacturing, Kazi Moshiur Rahman

Electronic Theses and Dissertations

Cellular metamaterials are of immense interest for many current engineering applications. Tailoring the structural organization of cellular structures leads to new metamaterials with superior properties providing lightweight and very strong/stiff structures. The incorporation of hierarchy to regular cellular structures enhances the properties and introduces novel tailorable metamaterials. For many complex cellular metamaterials, the only realistic manufacturing process is additive manufacturing (AM). The use of AM to manufacture large structures may lead to several types of defects during the manufacturing process, such as imperfect cell walls, irregular thickness, flawed joints, partially missing layers, and irregular elastic plastic behavior due to toolpath. …

Low Temperature Solution-Processed Sb:Sno2 Nanocrystals For Efficient Planar Perovskite Solar Cells, Yang Bai, Yanjun Fang, Yehao Deng, Qi Wang, Jingjing Zhao, Xiaopeng Zheng, Yang Zhang, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Inorganic metal oxide electron-transport layers (ETLs) have the potential to yield perovskite solar cells with improved stability, but generally need high temperature to form conductive and defect-less forms, which is not compatible with the fabrication of flexible and tandem solar cells. Here, we demonstrate a facile strategy for developing efficient inorganic ETLs by doping SnO₂ nanocrystals (NCs) with a small amount of Sb using a low-temperature solution-processed method. The electrical conductivity was remarkably enhanced by Sb-doping, which increased the carrier concentration in Sb:SnO₂ NCs. Moreover, the upward shift of the Fermi level owing to doping results in improved …

Propagation Of Extensional Waves In A Piezoelectric Semiconductor Rod, C.L. Zhang, X. Y. Wang, W. Q. Chen, J. S. Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We studied the propagation of extensional waves in a thin piezoelectric semiconductor rod of ZnO whose c-axis is along the axis of the rod. The macroscopic theory of piezoelectric semiconductors was used which consists of the coupled equations of piezoelectricity and the conservation of charge. The problem is nonlinear because the drift current is the product of the unknown electric field and the unknown carrier density. A perturbation procedure was used which resulted in two one-way coupled linear problems of piezoelectricity and the conservation of charge, respectively. The acoustic wave and the accompanying electric field were obtained from the equations …

Functional Performance Differences Between The Genium And C-Leg Prosthetic Knees And Intact Knees, Michael J. Highsmith, Jason T. Kahle, Rebecca M. Miro, M. E. Cress, Derek J. Lura, William S. Quillen, Stephanie Carey, Rajiv V. Dubey, Larry J. Mengelkoch

Mechanical Engineering Faculty Publications

Microprocessor prosthetic knees (MPKs) have advanced technologically, offering new features to decrease impairment and activity limitations for persons with transfemoral amputation (TFA). The Genium knee is functionally untested, and functional differences between it and intact knees are unknown. This study sought to determine whether Genium use improves functional performance compared with the C-Leg. A randomized experimental crossover design was used, with a cross-section of five nonamputee controls for comparison to nor­mal. Twenty community-ambulating persons with TFA were trained and tested for accommodation with study components. All subjects (n = 25) were assessed using the Continuous-Scale Physical Functional Performance-10 (CS-PFP10) …

User Involvement In The Partner Program Of The Educational Social Network, Ilya V. Osipov, Alex A. Volinsky, Anna Y. Praskikova

Mechanical Engineering Faculty Publications

The paper describes experiments to attract active online system users to the partner program. The objective is to grow the number of users by involving existing system users in viral mechanics. Several examples of user motivation are given, along with the specific interface implementations and viral mechanics. Viral K-factor was used as the metrics for the resulting system growth assessment. Specific examples show both positive and negative outcomes. Growth of the target system parameters is discussed.

Optimization-Based Path Planning For Separation Assurance On Small Unmanned Aircraft, Matthew Duffield, Andrew Ning, Timothy Mclain

Faculty Publications

This paper presents a time-based path planning optimizer for separation assurance for unmanned aircraft systems (UAS). Given Automatic Dependent Surveillance-Broadcast (ADS-B) as a sensor, intruder information such as position, velocity, and identification information is available at ranges on the order of 50 nautical miles. Such long-range intruder detection facilitates path planning for separation assurance, but also poses computational challenges. The time-based path optimizer presented in this paper provides a path-planning method that takes advantage of long-range ADS-B information and addresses the associated challenges. It is capable of long-range path planning and, due to the convex formulation, is computationally efficient enough …

Computational Assessment Of Neural Probe And Brain Tissue Interface Under Transient Motion, Michael Polanco, Sebastian Bawab, Hangsoon Yoon

Mechanical & Aerospace Engineering Faculty Publications

The functional longevity of a neural probe is dependent upon its ability to minimize injury risk during the insertion and recording period in vivo, which could be related to motion-related strain between the probe and surrounding tissue. A series of finite element analyses was conducted to study the extent of the strain induced within the brain in an area around a neural probe. This study focuses on the transient behavior of neural probe and brain tissue interface with a viscoelastic model. Different stages of the interface from initial insertion of neural probe to full bonding of the probe by astro-glial …