Mechanical Engineering Commons^™

Heat Exchanger Design And Development For Automotive Exhaust Waste Heat Recovery Using Thermoelectric Devices, Kazi S. Hassan

Open Access Theses & Dissertations

In this study several heat exchanger designs were constructed, tested, and the effect of the design on the overall efficiency and power generated by thermoelectric generators was measured. The thermoelectric elements were attached to the heat exchanger and hot gas passed through the system simulating automotive exhaust. An aluminum duct heat exchanger, a copper heat exchanger, and a heat exchanger with a twisted tape insertion were tested. The heat exchangers were all rectangular with similar dimensions and minimum thicknesses near the wall. The flow of exhaust gas was created by heated air flow ranging from 100-150 LPM. The cool side …

Electrical Characterization Of Microcrystalline Lifepo4 For Application In Lithium Ion Batteries, Sukhdeep Amarjeet Labana

Open Access Theses & Dissertations

Electrical Characterization of Microcrystalline LiFePO4 for application in lithium ion batteries. Mainly, to study about the electrical properties of Lithium Iron Phosphate as a cathode material to increase its Electrical consumption.

High-Order Central Finite-Volume Schemes For Atmospheric Modeling, Kiran Kumar Katta

Open Access Theses & Dissertations

Atmospheric numerical modeling has been going through drastic changes over the past decade, mainly to utilize the massive computing capability of the petascale systems. This obliges the modelers to develop grid systems and numerical algorithms that facilitate exceptional level of scalability on these systems. The numerical algorithms that can address these challenges should have the local properties such as the high on-processor operation count and minimum parallel communication i.e., high parallel efficiency. They should also satisfy the following properties such as inherent local and global conservation, high-order accuracy, geometric flexibility, non-oscillatory advection and positivity preservation properties. The goal of this …

Development Of A High Pressure Optically Accessible Combustor And Shear Co Axial Injector, Christopher David Navarro

Open Access Theses & Dissertations

A trend in the last decade in the field of propulsion and rocketry is leaning toward the use of the combination of Liquid Methane and Liquid Oxygen as propellant fuels. This is in contrast with the earlier trend of using Hydrogen systems and toxic hypergolic systems. The Multi-Purpose Optically Accessible Combustor (MOAC) and Shear Coaxial injectors have been developed to investigate injector design and combustion research involving Oxygen and Methane propellants. The MOAC is intended for the experimentation and research of combustion of liquid and gaseous propellants. Development of the MOAC system and versatility to use a number of injector …

Low Energy Disruption Of Lipid Containing Biomass, Joaquin Rodriguez

Open Access Theses & Dissertations

Lipid containing biomass from microalgae has received recent research interest as a renewable and sustainable feedstock for biofuel production. Algae is known to offer as much as 30 times the energy density than corn based ethanol, the current world standard for biomass based liquid transportation fuels. The development of large scale systems and methods of extracting lipids from microalgae is still in the early stages of development and significant increases in efficiency and reduction in costs are necessary to substantiate algae as a feasible alternative source of fuel. Traditional conversion of algae feedstock into a refineable feedstock for biofuel can …

Oxidation Of Borides And Carbides With Y2o3 And Ta Additions, Salvador Manuel Rodriguez

Open Access Theses & Dissertations

The study presented here describes an investigation of an oxidation scale of a fully-sintered Y2O3-ZrB2-TiC composite exposed in air at 1173K. Upon oxidation of the boride/carbide, a ZrO2-TiO2 was expected to form similar to the ZrO2-SiO2 dual scale of an oxidized ZrB2-SiC. The 47wt% Y2O3-38wt%ZrB2-16wt%TiC composite formed a dual scale consisting primarily of an Y2O3-ZrO2-TiC inner scale with an outer scale of ZrO2-TiO2-Y2O3.

The samples oxidized with a parabolic layer growth allowing the calculation of the effective diffusion coefficient indicating that the oxidation was controlled by oxygen ingress through primarily the ZrO2-Y2O3 phase. The oxygen potential between the inner layer …

Investigation On A Gas-Solid Fluidized Bed Hydrodynamics Using A Non-Intrusive Technology To Visualize Flow Field, Md Rashedul Hasan Sarker

Open Access Theses & Dissertations

The biggest challenge for 21st century is to fulfill global energy demand and at the same time reduce detrimental impact on environment. Gasification technology can meet the requirement and also reduce emission without compromising its performance. In coal gasification, instead of burning coal completely a partial combustion takes place with presence of steam and limited amount of oxygen. In this controlled environment a chemical reaction takes place and produces a mixture of clean synthetic gas. Gas-solid fluidized bed is one type of gasification technology. During gasification mixing behavior of solid (coal) and gas and their flow pattern very complicated to …

Control Of A Robotic Prototype Multi-Axis Synergistic System, Julio A. Torres

Open Access Theses & Dissertations

Balance is an ability that every person has and uses in normal daily life, to walk, run, stand, dance, etc. However, there are people who suffer a kind of balance impairment. The Computerized Dynamic Posturography (CDP) is technique in balance rehabilitation, where the patient is asked to stand on a moving platform that is equipped with sensors that measure how well you maintain your balance. In this thesis, a new CDP mechatronic system, the Multi-Axis Synergistic System (MASS), for balance assessment is being developed.

As a first stage and as the objective of this research work the transferable control algorithm …

Skin Cell Regeneration, Polette Cortez^, Maria Yanez, Thomas Boland*

COURI Symposium Abstracts, Summer 2011

No abstract provided.

Experimental Study Of Thermoelectric Properties For Randomly Distributed Carbon Nanotubes And Silicon Carbide Nanoparticles, Onasis Garcia

Open Access Theses & Dissertations

In this experimental study, the thermoelectric (TE) properties of carbon nanotubes (CNTs) and Silicon carbide (SiC) nanoparticles have been investigated. Nanoparticles were randomly disrtibuted on a non-conductive glass or quartz substrate. The carbon nanotubes used were single-walled and multi-walled type, consisting of approximately 60% semiconducting 40% metallic tubes. The experimental design is analogous to that of a thermocouple measurement, with the nanoparticle layers creating hot and cold joints with a dissimilar metal Alumel (Ni-Al). Voltage (mV), current (μA) and resistance (Ω) values were measured with respect to temperature (°C), and Seeback coefficient values were also calculated in parallel. Summarized results …

Evaluation Methods For Health Monitoring Of Aerospace Structure Rotary Joints, Sergio Armando Navarro

Open Access Theses & Dissertations

In September 2007, the excessive vibrations played a significant role in the station operation since one of the rotary joints, which provides the station electrical energy, presented an anomaly. The replacement of its bearing components and re-lubrication were necessary to reduce the problem. To avoid a new anomaly, the inspection of the rotary joints performance continues by using the accelerometers data. This thesis presents three new approaches to monitor the vibrations at the International Space Station based on Root-Mean-Square, kurtosis, and Approximate Entropy (ApEn). MATLAB functions and codes were necessary to implement the three monitoring techniques results from the provided …

Development Of A Heat Transfer Test Rig For Finding Heat Transfer Characteristics Of Liquid Methane, Sergio Flores

Open Access Theses & Dissertations

Most large scale rocket engines use a regeneratively cooled system to cool the rocket engine using either the rocket fuel or oxidizer. The use of liquid methane as a rocket fuel is an emerging technology proving to have several advantages over current rocket fuels. However, liquid methane is lacking the extensive research as a rocket fuel compared to highly used rocket fuels like liquid hydrogen. A heat transfer test rig was built with the goal to characterize the heat transfer characteristics of liquid methane as it passes through a heated channel. The development of the test rig underwent considerations designed …

On Feasibility Of Reducing Metal Fuel Content And Operating Temperatures In Chemical Oxygen Generators, Allen Garcia

Open Access Theses & Dissertations

Chemical oxygen generators are widely used in aircraft, submarines, spacecraft, and other applications, problems such as combustion instabilities and a risk of fire may be present. For example, due to malfunction of an oxygen generator, fire occurred onboard the Mir Space Station in 1997. It is thus important to improve the process stability and fire safety of chemical oxygen generators. Chemical compositions for oxygen generators include an oxygen source such as sodium chlorate (NaClO3), a transition metal oxide as a catalyst, and a metal fuel to provide energy for self-sustaining combustion. Eliminating or decreasing the metal fuel would decrease the …

Study Of Probabilistic Approach For Structural Health Assessment Of Aerospace Structures, Jose Antonio Garcia

Open Access Theses & Dissertations

Current practical approaches used in structural health assessment programs of aerospace structures involve performing a fracture mechanics analysis to verify the safe life of structural components. The analysis typically makes several conservative assumptions implemented by NASA fracture control standard practices for critical structural components. This well-established paradigm for fracture control follows a deterministic approach and, in some cases, the calculations may produce overly conservative remaining life estimates.

This thesis describes the results of a study to approach the health assessment challenge of several critical components using probabilistic methods. The probabilistic analysis takes the current deterministic model and identifies variables that …

Investigation On Flame Characteristics Of Oxy-Fuel Combustion, Md R. Islam

Open Access Theses & Dissertations

Oxy-fuel combustion is currently being considered by the U.S Department of Energy as a promising technology for efficient carbon capture. This technology could substantially reduce NOx and CO2 emissions. In addition, the implementation of oxy-fuel combustion technology in a power generation system could potentially reduce negative environmental impacts of fossil fuel use. It also encourages the use of reliable and domestic energy sources. The U.S. Department of Energy has made efforts to investigate the performance of a CO2 and H2O diluted oxy-fuel combustion system in a high-pressure combustor. In an effort to better understand and characterize the fundamental flame characteristics …

A Combined X-Fem And Level Set Approach For Modeling Composite Material's Micro Structure, Himanshu Kumar

Open Access Theses & Dissertations

Composite materials are usually made of fibers and binding matrix. It's always a challenge to model composite materials' microstructure through the traditional finite element method because construction of an approximation space which is discontinuous across a given line or surface will place strict restrictions on the FE mesh. The interfacing of fibers in composites' microstructure through the standard finite element method is irksome and tedious because the presence of fiber presents a discontinuity in the binding material. In this present work, the composite's microstructure is modeled through the combined approach of Level Set and Extended Finite Element Method. The fiber …

Synthesis, Microstructure And Thermal Analysis Of Gd2o3 - Hfo2 Coatings, Chandan Kumar Roy

Open Access Theses & Dissertations

Thermal barrier coatings (TBCs) are critical for future gas turbines of advanced coal based power generation systems. The TBCs are protective layers of low thermal conductivity ceramic materials, which prevent the damage of components that are exposed to very high temperature of the hot gases. Due to increasing demand to improve the efficiency, it is necessary to find alternate TBC materials which can withstand higher temperature for longer period than state-of-art TBCs. The present study focuses on the Gd2O3 stabilized HfO2 (GSH) as a potential candidate for TBC. GSH materials were synthesized in bulk and coatings form. The Gd2O3 content …

Experimental Investigation Of Magnesium/Regolith Combustion For In-Situ Production Of Materials On The Moon, Christopher White

Open Access Theses & Dissertations

Future settlements on the Moon will require that strong, cost-effective structural materials be developed in whole or in part from locally available resources. Such materials can be created in-situ from the lunar regolith using self-propagating high-temperature synthesis (SHS). By mixing the lunar regolith with metal additives, such as aluminum or magnesium, a combustible mixture is formed which, when ignited, can reach temperatures high enough to allow combustion to be self-sustaining, sintering the lunar regolith without further energy input and without the need for atmospheric oxygen. The resulting products may be strong enough for some structural applications, such as radiation shielding, …

Combustion Of Lunar Regolith Mixed With Energetic Additives: Thermodynamic Calculations And Experimental Studies, Francisco Alvarez

Open Access Theses & Dissertations

The future of space exploration will require longer missions in order to better understand the conditions of near-Earth celestial objects, like the Moon or Mars. Future space missions will require the development of goods, such as propulsion fuel and structural materials, produced using the extraterrestrial resources available. The area that develops these technologies is called In-Situ Resource Utilization (ISRU). ISRU allows reducing the payload, and as a consequence reduces the energy consumption and cost of space travel. The production of structural materials on the Moon can be accomplished using Self-Propagating High-Temperature Synthesis (SHS). This work describes the combination of ISRU …

Design And Cfd Optimization Of Methane Regenerative Cooled Rocket Nozzles, Christopher Linn Bradford

Open Access Theses & Dissertations

Liquid rocket engines benefit in life cycle from the active regenerative cooling method which passes the fuel as the coolant through channels surrounding the combustion chamber. These channels are designed and optimized using structural considerations as well as heat transfer theory, then CFD simulations with the software FLUENT are performed for the final analysis. The difficulty in using methane as the fuel/coolant is addressed, and requires the use of the ideal gas numerical model in preliminary CFD simulations. Comparison to real gas numerical models is made, and results also given for one channel design. The techniques utilized herein allow the …

Experimental And Numerical Investigation Of The Effect Of Fuel Composition On Flame Stability On A Gas Turbine Combustor, Gilberto Corona

Open Access Theses & Dissertations

Gas turbines are used for power generation and aviation all over the world. Fossil fuels remain the main source of energy for the operation of gas turbines but the recent increase in environmental awareness has influenced government agencies to impose stringent limits on pollutant emissions from power generation plants. Pollutant emissions control is one of the major challenges for gas turbine designers. In this study, experimental methods and computational fluid dynamics (CFD) technologies are used to study the problems that arise when coal derived fuels are used in Gas Turbine Combustors.

Gas turbine designers need both experimental data and combustion …

Improved Joining Method For Segmental Prestressed Structures, Ralph Warren Jensen

Open Access Theses & Dissertations

This dissertation addresses the need for more robust and materially efficient structures, specifically structures that absorb higher levels of energy, can self-erect and which have variable reaction capabilities. These structures can take much higher levels of strain and loading compared to current technologies in reinforced concrete and carbon fiber composites. These structures are made using a novel method of joining segmental elements. A great advantage with this segmental structural system is it's survivability under overloaded conditions. During an impact, or concentrated pressure load, the structure will wrap around the impact zone thereby widely distributing the contact stresses. This function or …

An Investigation On Pulsing Performance Of Mn Class Bi-Propellant Thrusters, Carlos Francisco Gomez

Open Access Theses & Dissertations

With the advancement of technology and machining methods, considerable attention has been focused in manufacturing micro thrusters for micro spacecraft applications (Yetter et al, 2003). Micro propulsion systems are currently being investigated for Miniature Kill Vehicles (MKV) and Micro Satellite Systems (MSS) with an emphasis in reducing weight and cost but without affecting performance. Reducing the weight seems practical when reducing the size of the propulsion system, but problems are encountered with system design.

In addition, propulsion requirements strongly influence choice in propellant and complexity. A thorough understanding of stabilizing thrust levels and the ability to control the propulsion system …

Combustion Characteristics Of Alh3 Flame, Sudipa Sarker

Open Access Theses & Dissertations

The combustion characteristics of Al hydride and Al were compared using a combustion chamber. Burning rate, ignition energy and temperature at atmospheric temperature and pressure in carbon dioxide and O2 were tested with a volumetric flow rate that ranged from 10 to 50% in Ar. A spark ignition system was used to ignite the Alane and Aluminum. The combustion rate was measured using a high speed camera. Results showed the combustion rate of Alane and Aluminum decreases with increasing volumetric flow rate of oxidizer. And the combustion rate of Alane is higher than that of Aluminum. Alane needs more ignition …

Scaffold Based In-Vitro Osteodistraction For Bone Tissue Engineering, Cesar Adrian Terrazas

Open Access Theses & Dissertations

Engineering of hard tissues such as bone is a challenge because of the limited ability of the body to heal large defects. Current treatment options, such as employing bone sections from the patient or a deceased donor have been utilized for some time now with various degrees of success. However, these methods still exhibit many limitations such as limited supply and the possibility of transmission of disease.

To address the many limitations of bone grafts, synthetic engineered substitutes have been developed and widely researched for nearly three decades. Generally termed scaffolds, these are matrices that serve the purpose of temporary …

Sensitivity Analysis Of The Johnson-Cook Plasticity Model For Hypervelocity Impacts: A Hydro-Code Study, Carlos David Castellanos

Open Access Theses & Dissertations

Computer simulations have been in use for decades in the modeling of hypervelocity impacts and general large deformation problems. Several computer codes have been developed to simulate this type of problems under a variety of geometric configurations and for any number of materials. These codes make use of several constitutive material models to simulate the response of the material under a variety of thermo-mechanical conditions. The Johnson-Cook constitutive model is widely used in the simulation hypervelocity impacts for the simulation of crater formation and even perforation of target structures. This thesis presents the results of a sensitivity study of this …

Multidisciplinary Collaborative Model For Complex, Angel Ernesto Delgado

Open Access Theses & Dissertations

Nowadays, most devices with advanced technology require the development of embedded systems with mechanical and electrical components as well as software including more than one discipline. These are devices that are usually complex in terms of composition and functionality and that design must follow a methodology in order to successfully design and launch a device of this nature. Hence, the assembly of a multidisciplinary engineering group is required to carry out such complex devices and develop a fully functional product. The group may also need an expert on the field that can provide guidance and knowledge where needed. This is …

Automated Fluid Handling And Leveling System For Multiple Material Stereolithography, Yinko I. Grajeda

Open Access Theses & Dissertations

This work addresses the development of an automated multiple material fluid handling and leveling system for its implementation into a Multiple-Material Stereolithography (MMSL) apparatus. A patent filed by Wicker et al. (US Patent 7,556,490) disclosing a MMSL apparatus served as the basis for the development of this work. The system is designed to operate in a variety of MMSL apparatus configurations. Fluid vats are designed to meet the enclosure constraints, facilitate the interface to the pump and sensor, and support the handling of the fluids. Due to its fluid isolation and bi-directional flow capabilities, a digital drive peristaltic pump is …

Processing Of Zrb2-Zrc-Zrxsiy Ceramic By Reactive Metal Penetration, Nischel B. Maheswaraiah

Open Access Theses & Dissertations

The processing of ZrB2-ZrC-ZrxSiy composite by reactive metal penetration was investigated as a successor to the ZrB2-SiC composites for hypersonic vehicles application, which cannot be used for extended time at temperatures greater than 1600C due to formation of SiO and CO gases. Zirconium (Zr), zirconium disilicide (ZrSi2), and boron carbide (B4C) were reacted in graphite crucibles for 60, 120, 180, and 240 minutes. Microscopy and x-ray diffraction (XRD) deduced the formation of a heterogeneous microstructure of ZrB2-ZrC-ZrxSiy precipitates surrounded by a solidified Zr-Si melt. Unreacted boron carbide was observed in samples held at 1860C for 60 minutes and 120 minutes, …

Development Of A Micro-Catbed For Miniature Thrusters, Chance Paul Garcia

Open Access Theses & Dissertations

The goal of this work is to develop a micro catalytic bed for miniature thrusters. A test bed was constructed for experimental testing to characterize several parts of the micro catalytic bed. The reactant fluid studied is 90% Hydrogen Peroxide (H2O2) by weight. Three different cross sectional area designs were tested to determine decomposition efficiency, temperature reaction propensity, optimum flow rate, and temperature distribution across each bed. The products of decomposition were condensed to measure the oxygen released from decomposition. The results will be used to develop the basis for a micro catalytic bed design to implement into future miniature …