Materials Science and Engineering Commons^™

Investigation On Structural Heritability And Durability Of High Sulfate Resistance Portland Cement Mortar Modified By Aluminum Salt, Jun Xu

International Conference on Durability of Concrete Structures

The essential hydration and hardened properties of high sulfate resistance Portland cement paste/mortar were investigated with Al₂(SO₄)₃ as admixture. Experiment results showed that that the addition of Al₂(SO₄)₃ promoted the hydration of HSRP cement pastes, and the hydration rate accelerated with the increase of the addition amount. The mechanical properties and chloride diffusion coefficient of cement mortar were obviously improved with 0.25% Al₂(SO₄)₃ addition . For instance, the compressive strength of AS0.25 cement mortars was 24.8% higher than AS0 samples and the chloride ion migration …

Room-Temperature Mechanical Properties Of A High-Entropy Diboride, Alec C. Murchie, Jeremy Lee Watts, William Fahrenholtz, Gregory E. Hilmas

Materials Science and Engineering Faculty Research & Creative Works

The mechanical properties of a (Hf,Mo,Nb,Ta,W,Zr)B2 high-entropy ceramic were measured at room temperature. A two-step synthesis process was utilized to produce the (Hf,Mo,Nb,Ta,W,Zr)B2 ceramics. The process consisted of a boro/carbothermal reduction reaction followed by solid solution formation and densification through spark plasma sintering. Nominally, phase pure (Hf,Mo,Nb,Ta,W,Zr)B2 was sintered to near full density (8.98 g/cm3) at 2000°C. The mean grain size was 6 ± 2 µm with a maximum grain size of 17 µm. Flexural strength was 528 ± 53 MPa, Young's modulus was 520 ± 12 GPa, fracture toughness was 3.9 ± 1.2 MPa·m1/2, and hardness (HV0.2) was 33.1 …

Production Of Low-Cost Self-Consolidating Concrete (Scc) Using Manufactured Aggregates, Rabab Raydan, Farah Chamseddine, Ali Jahami, Oussama Baalbaki, Jamal Khatib, Adel Elkordi

BAU Journal - Science and Technology

Limitations to the sources of aggregates and the unavailability of sand is becoming a problematic issue for concrete production. A novel technology of manufactured aggregates can produce well graded round aggregates that can substitute natural aggregates while maintaining the same characteristics needed and preserving the resources. Self-Consolidating Concrete (SCC) using manufactured aggregates is assessed in this experimental work to understand the variability of workability properties and mechanical properties with the changes in w/c ratio and percentages of Coarse Aggregates and Manufactured Sand to Natural Sand in order to choose the best mixture that satisfies an adequate overall performance. Targeting compressive …

Insect Antennae As Bioinspirational Superstrong Fiber-Based Microfluidics, Griffin J. Donley

All Theses

Nature is frequently turned to for inspiration for the creation of new materials. Insect antennae are hollow, blood-filled fibers with complex shape, and are cantilevered at the head. The antenna is muscle-free, but the insect can controllably flex, twist, and maneuver it laterally. To explain this behavior, a comparative study of structural and tensile properties of the antennae of Periplaneta americana (American cockroach), Manduca sexta (Carolina hawkmoth), and Vanessa cardui (painted lady butterfly) was performed. These antennae demonstrate a range of distinguishable tensile properties, responding either as brittle fibers (Manduca sexta) or strain-adaptive fibers that stiffen when stretched (Vanessa cardui …

Plasma Spheroidization Of Gas-Atomized 304l Stainless Steel Powder For Laser Powder Bed Fusion Process, M. Hossein Sehhat, Austin T. Sutton, Chia-Hung Hung, Ben Brown, Ronald J. O'Malley, Jonghyun Park, Ming-Chuan Leu

PSMRC Faculty Research

Particles of AISI 304L stainless steel powder were spheroidized by the induction plasma spheroidization process (TekSphero-15 spheroidization system) to assess the effects of the spheroidization process on powder and part properties. The morphology of both as-received and spheroidized powders was characterized by measuring particle size and shape distribution. The chemistry of powders was studied using inductively coupled plasma optical emission spectroscopy for evaluation of composing elements, and the powder’s microstructure was assessed by X-ray diffraction for phase identification and by electron backscattered diffraction patterns for crystallography characterization. The Revolution Powder Analyzer was used to quantify powder flowability. The mechanical properties …

The Effect Of Green Biobased Binder On Structural, Mechanical, Liquid Absorption And Wetting Properties Of Coated Papers, Bilge N. Altay, Charles Klass, Ting Chen, Alexandar Fleck, Cem Aydemir, Arif Karademir, Paul D. Fleming

Articles

Synthetic styrene-butadiene (SB) and styrene-acrylic (SA) latex binders used in paper coating formulations are common and based on unsustainable petroleum sources. Today's papermaking industry turns towards sustainable substitutes that do not compromise quality, and reduce carbon emission, toxic substance release and waste disposal concerns related to fossil fuel sources. In this study, colloidal starch-based latex nanoparticles that do not require cooking were used for pigment coating and coated on the paper surfaces. The effects of these new biobased binders on the structural and mechanical strength properties, liquid absorption, wetting and surface topography of the paper were investigated and compared with …

An Investigation Into Energy-Material Properties Interaction In Additive Manufacturing Of Polymers., Pu Han

Electronic Theses and Dissertations

Additive manufacturing (AM), known as three-dimensional (3D) printing, is a fabrication process to build 3D objects layer by layer based on computer aided design (CAD) model or digital 3D model. Fused filament fabrication (FFF) has become a preferred method for additive manufacturing due to its cost-effectiveness and flexibility. However, the parts built using FFF process suffer from lower mechanical strength compared to that fabricated using traditional method and rough surface finish. With this motivation, this dissertation aims to develop and implement a novel in-process laser assisted technique on FFF to heal the microstructure of FFF built objects by enhancing reptation …

Enhancement Of Asphalt Performance By Graphene-Based Bitumen Nanocomposites, Sara Moghtadernejad, Ehsan Barjasteh, Ren Nagata, Haia Malabeh

Mineta Transportation Institute

As the State of California continues to grow, demand for enhanced infrastructure such as roadways and highways escalates. In view of the current average highway lifespan of 15–20 years, the improvement of asphalt binders leads to material sustainability by decreasing required maintenance and increasing the lifespan of roadways. In the present investigation, enhancement of asphalt binder properties was achieved by different methods of mixing varying compositions of graphene nanoparticles with an SBS polymer and asphalt binder. Additionally, experimental evaluation and comparison of the rheological and mechanical properties of each specimen is presented. Graphene nanoparticles have attracted great curiosity in the …

Strengthening Of 7175 Aluminum Alloy Through Multi-Step Aging Process, Colin E. Masterson, Ryland W. Jolliffe

Materials Engineering

7175 is a heat-treatable aluminum alloy commonly used in aerospace forgings. This alloy is aged with a multi-step heat treatment. This treatment must balance strength with stress corrosion cracking resistance through a degree of overaging. The team was tasked by Weber Metals to increase the strength of this treatment without sacrificing stress corrosion cracking resistance. Both two-step and retrogression and reaging treatments were tested in experiments to find a heat treatment that could increase the yield and tensile strength by 1-2 ksi while maintaining a minimum electrochemical conductivity equivalence of 38% relative to copper. Two-step aging is the more conventional …

Copper Slag As A Potential Waste Filler For Polyethylene-Based Composites Manufacturing, Aleksander Hejna, Paulina Kosmela, Mateusz Barczewski, Olga Mysiukiewicz, Adam Piasecki

Tanzania Journal of Science

The present study aimed to analyze the application of waste material from copper production– copper slag (ŻŻL) as filler for composites based on the high-density polyethylene (HDPE). Copper slag filler was introduced in the amounts of 1–20 wt%, and its influence on the appearance (color analysis), chemical structure (Fourier-transform infrared (FTIR) spectroscopy), microstructure (optical microscopy), as well as static (tensile tests) and dynamic (dynamical mechanical analysis (DMA)) mechanical properties of composites were investigated. Proper dispersion of filler implicated that the incorporation of up to 5 wt% of filler caused only slight, 5% drop of tensile strength, with the simultaneous 16% …

Microstructure Evolution And Mechanical Property Response Of Tc11 Titanium Alloy Under Electroshock Treatment, Chang Liu, Lechun Xie, Dongsheng Qian, Lin Hua, Liqiang Wang, Lai-Chang Zhang

Research outputs 2014 to 2021

© 2020 The Authors This work investigated the effects of electroshock treatment (EST) on the microstructure variation and mechanical properties of TC11 alloy. The average hardness of the specimens decreased from 358 HV to 328 HV after EST of 0.04 s, then increased to 396 HV after EST of 0.06 s. After EST, the yield strength of specimen declined from 959 MPa to 797 MPa after EST of 0.04 s, and then increased to 1265 MPa after EST of 0.06 s, but the fracture strain decreased continuously. The variation in mechanical properties was closely related to the phase transition from …

Determination Of Hydrogel Degradation By Passive Mechanical Testing, Avery Rosh-Gorsky

Honors Theses

This paper details a new technique to measure the mechanical properties of ETTMP PEGDA hydrogels using Hertz Contact Theory and simultaneously analyze both the model drug release and gel erosion in situ. This method involves curing a drug loaded hydrogel in a standard cuvette and placing a glass bead and phosphate buffer solution (PBS). Over time, the cross-linked network of the hydrogel breaks down, and, as a result, the ball sinks into the hydrogel. This method provides a macroscopic and inexpensive way to continuously and passively measure properties of the hydrogel as the hydrogel degrades. By plotting both the …

Exploring Rapid Solidification And Equal Channel Angular Pressing In The Fabrication Of Mg-Based Alloys For Medical Applications, Emily Tom

Dissertations, Master's Theses and Master's Reports

The development of magnesium bioresorbable implants has become increasingly popular due to the increased need for temporary implants and magnesium’s excellent biocompatibility and suitable elastic modulus. Even though magnesium is an excellent candidate, when alloyed with other metals magnesium’s corrosion rate becomes too rapid for bioresorbable medical applications. The investigation into novel processing techniques to control the formation of precipitates to improve mechanical strength and ductility as well as corrosion rates has become of interest. This work investigates the combination of two nonequilibrium processing techniques, rapid solidification (RS) and equal channel angular pressing (ECAP), and the effects it has on …

Properties And Performance Of The Basalt-Fiber Reinforced Texture Roof Tiles, Parinya Chakartnarodom, Wichit Prakaypan, Pitcharat Ineure, Nutthita Chuankrerkkul, Edward A. Laitila, Nuntaporn Kongkajun

Michigan Tech Publications, Part 1

The mechanical and the physical properties, and the performance of texture roof tiles reinforced with the basalt fibers were observed. The samples of the basalt-fiber reinforced texture roof tiles were produced on the industrial scale by using filter pressing method. After forming, the as-molded samples were air cured and characterized based on ASTM C1185 standard for their mechanical properties and physical properties. In addition, the roof-tile installation test was also performed. The results showed that the samples of the basalt-fiber reinforced texture roof tile (BFRT) could be produced on the industrial scale by using the common setting of the forming …

The Effect Of Compaction Temperature And Pressure On Mechanical Properties Of 3d Printed Short Glass Fiber Composites, Pushpashree Jain Ajith Kumar Jain

Mechanical & Aerospace Engineering Theses & Dissertations

Among many thermoplastics that are used in engineering, polyamide 6 (nylon 6) is an extremely versatile engineering thermoplastic. Nylon filled with glass fibers has higher mechanical strength and high wear resistance than general purpose nylon. 3D printed composites, based on fused filament modeling, typically suffer from poor bead-to-bead bonding and relatively high void content, limiting their mechanical properties

This thesis explores the effect of compaction pressure and temperature on improving the mechanical properties of 3D printed composites. Engineering moduli in the printing and transverse to printing direction, as well as ultimate strength were measured using the tensile testing with Digital …

Aerosol Jet Printed Capacitive Strain Gauge For Soft Structural Materials, Kiyo T. Fujimoto, Jennifer K. Watkins, Timothy Phero, Takoda Bingham, Kshama Lakshmi Ranganatha, Benjamin C. Johnson, Zhangxian Deng, Brian Jaques, David Estrada

Materials Science and Engineering Faculty Publications and Presentations

Soft structural textiles, or softgoods, are used within the space industry for inflatable habitats, parachutes and decelerator systems. Evaluating the safety and structural integrity of these systems occurs through structural health monitoring systems (SHM), which integrate non-invasive/non-destructive testing methods to detect, diagnose, and locate damage. Strain/load monitoring of these systems is limited while utilizing traditional strain gauges as these gauges are typically stiff, operate at low temperatures, and fail when subjected to high strain that is a result of high loading classifying them as unsuitable for SHM of soft structural textiles. For this work, a capacitance based strain gauge (CSG) …

Microstructural Evolution And Mechanical Properties Of Ultra-Fine Grained Tubular Components Processed By Severe Plastic Deformation, Mesbah Mohsen

Student Works (2020-2029)

The lightweight alloys have been widely used in various engineering applications such as automotive, aerospace, construction, and biomedical industries due to their low densities, high ductility, formability, and facile machining. However, the emerging trend for materials with high mechanical strength and plasticity hampers the widespread application of these alloys. Over the last two decades, severe plastic deformation (SPD) has been introduced as a promising approach for enhancement of the mechanical performance of the lightweight alloys through microstructural manipulations and grain refinement. However, the SPD techniques have been extensively utilized for the fabrication of non-tubular geometries and the studies on the …

Effects Of New And Recycle Flux On The Mechanical Properties Of Submerged Arc Welded (Saw) Line Pipe Grade X52m And X65m, Taib Meor Mohd Adli

Student Works (2020-2029)

Two line pipe grade X52M and X65M were manufactured using submerged arc welding process. For each grade, two different welding flux condition were simulated, i.e. 100% new flux and 100% recycle flux. The flux used was aluminate basic type trade name OP 132. The outside diameter and wall thickness for X52M was 610mm x 12.7mm and for X65M was 762mm x 14.3mm. Lower weld re-entrant angle and higher weld bead height were observed in recycle flux condition. Lower weld manganese content recorded in recycle flux condition. And lower mechanical tests (i.e. tensile, impact, and hardness) value reported for recycle flux …

Materials-Processing Relationships For Metal Fused Filament Fabrication Of Ti-6al-4v Alloy., Paramjot Singh

Electronic Theses and Dissertations

Additive manufacturing (AM) is at the mainstream to cater the needs for rapid tooling and small-scale part production. The metal AM of complex geometries is widely accepted and promoted in the industry. While several metal AM technologies exist and are matured to a level where expectation in terms of design and properties are possible to realize. But the metal AM suffers from the heavy expense to acquire equipment, isotropic property challenges, and potential hazards to work with loose reactive metal powder. With this motivation, the dissertation aims to develop the fundamental aspects to print metal parts with bound Ti-6Al-4V powder …

Effects Of Polytetrafluoroethylenemicro–Particles On Mechanical Andtribological Properties Of Glass Fiberreinforced Polyoxymethylene, Kunnan Singh Jasbir Singh

Student Works (2020-2029)

Reinforcing polyoxymethylene (POM) with glass fibers (GF) enhances its mechanical properties, but at the expense of tribological performance. Formation of a transfer film to facilitate tribo–contact is compromised due to the abrasiveness of GF. As a solid lubricant, for example, polytetrafluoroethylene (PTFE) significantly improves friction and wear resistance. The effects of chemically etched PTFE micro–particles on the fiber– matrix interface of POM/GF/PTFE composites have not been systematically characterized. This research investigated the effects of PTFE micro–particles on mechanical and tribological properties of POM/GF/PTFE composites. Since PTFE is immiscible with most polymers, the surface was etched using sodium naphthalene salt dissolved …

Development Of B-Type And Multi-Ion Doped Carbonated Hydroxyapatite Bioceramics, Safarzadeh Marjan

Student Works (2020-2029)

The present research is aimed to investigate the effect of varying the carbonate to phosphate (CO32−/ PO43‒) molar ratios from 0.5 to 5 on the physical and mechanical properties of carbonated hydroxyapatite (CHA) synthesized by a wet chemical method. The sintering was performed under dry carbon dioxide atmosphere at 900 °C to maintain the B-type CHA structure. It was found that increases in CO32−/ PO43‒ ratio was accompanied by an increase in the c/a lattice ratio. The diffraction peaks of the synthesized 0.5-5 CHA powders exhibited a single phase material except for 5CHA which revealed the some minor calcite or …

Effect Of Cobalt In Thin Wall Ductile Iron And Solid Solution Strengthened Ferritic Ductile Iron, Alejandra I. Almanza

Dissertations, Master's Theses and Master's Reports

Ductile Iron is a material that is constantly evolving. Consequently, the ferrous industry is not only focusing on lightweighting but also on improving the impact strength and fracture toughness of typical ferritic-pearlitic ductile iron grades and solid solution strengthened ferritic ductile irons. Recently, the demand for thin-wall ductile iron and solid solution strengthened ferritic ductile iron grades has increased. The challenges behind the fabrication of these two ductile iron materials are the presence of carbides and the embrittlement of ferrite. In response, research has been focused on looking at alternative methods that can mitigate carbide formation in thin sections and …

Microstructure And Mechanical Behavior Of Metastable Beta Type Titanium Alloys, Chirag Dhirajlal Rabadia

Theses: Doctorates and Masters

Current biomaterials such as stainless steel, Co-Cr alloys, commercially pure titanium and Ti-6Al- 4V either possess poor mechanical compatibility and/or produce toxic effects in the human body after several years of usage. Consequently, there is an enormous demand for long-lasting biomaterials which provide a better combination of mechanical, corrosion and biological properties. In addition to this, alloys used in high-strength applications possess either high-strength or large plasticity. However, a high-strength alloy should possess a better blend of both strength and plasticity when used in high-strength applications. Metastable β-titanium alloys are the best suited alloys for biomedical and high-strength applications because …

A Study On Ultrasonic Energy Assisted Metal Processing : Its Correeltion With Microstructure And Properties, And Its Application To Additive Manufacturing., Anagh Deshpande

Electronic Theses and Dissertations

Additive manufacturing or 3d printing is the process of constructing a 3-dimensional object layer-by-layer. This additive approach to manufacturing has enabled fabrication of complex components directly from a computer model (or a CAD model). The process has now matured from its earlier version of being a rapid prototyping tool to a technology that can fabricate service-ready components. Development of low-cost polymer additive manufacturing printers enabled by open source Fused Deposition Modeling (FDM) printers and printers of other technologies like SLA and binder jetting has made polymer additive manufacturing accessible and affordable. But the metal additive manufacturing technologies are still expensive …

Development Of Stage-I Tempered High Strength Cast Steel For Ground Engaging Tools, Viraj Ashok Athavale

Doctoral Dissertations

"Ground Engaging Tools (GET) are the expendable replacement parts used in heavy machinery used with mining or construction equipment. GET’s protect the expensive machine components from the wear and tear found common in high-impact or high-abrasion environments. The goal of this project is to develop advanced next-generation alloy choices that outperforms the existing GET materials. A method of predicting tempered hardness of mixed microstructures was formulated. Using this model, two alloy series viz. Cr-Ni-Mo and Mn-Si-Mo-V were proposed and experimented with the goal of obtaining a high strength and impact resistant cast steel. Cast iterations of Cr-Ni-Mo alloy series were …

Analysis Of Mechanical Properties And Permeability Of Sand Moulding By Using Eggshell In Sand Casting, Wahyu Kurnianto, Poppy Puspitasari, Wahono Wahono

Journal of Mechanical Engineering Science and Technology (JMEST)

This study aimed to analyse the usage of Eggshell as mixture material of bentonite in metal casting process which used dried sand moulding. Eggshell variations in this study were 4%, 7%, 10% eggshell, and additional 3% of bentonite on each sample. This study used pre-experimental method and included to OneShot Case Study model. The highest strength was found on the sample 3 ES 10%. Tensile strength of dried sand moulding reach up to 0.09 kg/cm2, the compressive strength of dried sand moulding reached up to 3.11 kg/cm2, and the shear strength of dried sand moulding reached up to 1.13 kg/cm2. …

The Analysis Of Permeability And Mechanical Properties Of Sand Moulding Using Mixed Material Clamshell (Placuna Placenta) On Sand Casting, Kritchakhris Nawettanaprasert, Zakaria Bagus Aminanta, Putut Murdanto

Journal of Mechanical Engineering Science and Technology (JMEST)

This study objected to determine mechanical properties of sand moulding by conducting tensile test, compressive and shear test, and also permeability test. This study also had the other objective that was analyse clamshell (Placuna placenta) as mixture material for bentonite as binder in manufacturing sand moulding in order to reduce the usage of bentonite. The method that used in this study was pre-experimental method with One-Shot Case Study model. The best mechanical properties obtained on sample 3 clamshell 11%, permeability results obtained was 190 ml/min, tensile strength results obtained for the dry sand was 0.015 kg/cm2, compressive strength obtained for …

Aging Response And Precipitation Behavior After 5% Pre-Deformation Of An Al-Mg-Si-Cu Alloy, Shuoxun Jin, Tungwai Ngai, Liejun Li, Shian Jia, Tongguang Zhai, Dongjie Ke

Chemical and Materials Engineering Faculty Publications

In this study, Al-1.00 Mg-0.65 Si-0.24 Cu alloy was solution heat-treated, water-quenched, and then pre-deformed for 5% before aging. The peak hardness and yield strength of the pre-deformed sample with subsequent artificial aging were similar to that of a T6 condition sample. It was also found that the pre-deformation treatment could inhibit the negative influence of natural aging to some degree. After seven days of natural aging, the pre-deformed sample obtained better peak hardness and yield strength upon artificial aging than the sample without pre-deformation. In addition, the pre-deformation treatment could reduce 50% of the artificial aging time to reach …

Mechanical Properties And Permeability Of Sand Casting Moulds With Eggshells Binder, Maryam Sharifi Jebeli Sharifi Jebeli, Wahyu Kurnianto, Wahono Wahono

Journal of Mechanical Engineering Science and Technology (JMEST)

This research aimed to analyse whether or not eggshell could be a potential addition to sand mould composition as a binding material together with bentonite. Different amounts of eggshell material, i.e. 4%, 7%, 10% and 3%, were added to each sample. This study was a type of pre-experimental design called the one-shot case study. Among all sand moulds under study, sample 3 10% ES in dry conditions had the highest tensile, compressive and shear strengths of 0.09 Kg/cm2, 3.11 Kg/cm2 and 1.13 Kg/cm2, respectively. The results of the permeability test with heat treatment at 110˚C for 60 minutes showed that …

Characterization Of Process Induced Defects In Laser Powder Bed Fusion Processed Alsi10mg Alloy, Edward Stugelmayer

Graduate Theses & Non-Theses

Additive manufacturing using laser powder bed fusion (AM-LPBF) methods have recently experienced rapid growth and development, having the potential to replace manufacturing by plastic deformation, precision machining, or casting. AM offers advantages such as the freedom to design highly complex geometries, time and cost savings through material usage efficiency and shortened production cycles, and the potential for improved mechanical properties. Process induced defects, however, result in degradation and scattering of mechanical properties and hinder the widespread adoption of AM-LPBF in industry. This investigation focuses on the effects of varying energy density and build orientation on the evolution of process induced …