Materials Science and Engineering Commons^™

A Computational Investigation Of Wood Selection For Acoustic Guitar, Jonah Osterhus

Senior Honors Theses

The acoustic guitar is a stringed instrument, often made of wood, that transduces vibrational energy of steel strings into coupled vibrations of the wood and acoustic pressure waves in the air. Variations in wood selection and instrument geometry have been shown to affect the timbre of the acoustic guitar. Computational methods were utilized to investigate the impact of material properties on acoustic performance. Sitka spruce was deemed the most suitable wood for guitar soundboards due to its acoustic characteristics, strength, and uniform aesthetic. Mahogany was deemed to be the best wood for the back and sides of the guitar body …

Effects Of Bending And Re-Bending On Mechanical Properties Of Locally-Manufactured Steel Rebars, Patrick W. Waruhiu, Simon I. Marandu, Mussa I. Mgwatu

Tanzania Journal of Science

Steel rebars experience deformation when subjected to bending and re-bending operations. Subsequently, their microstructures are impaired thus affecting the mechanical properties and leading to failure. This study establishes the effects of bending and re-bending the steel rebars on the mechanical properties. Experiments were conducted to determine the effects of bending and re-bending of the steel rebars. Testing was conducted on Ten virgin and Thirty specimens which were bent and re-bent at 45º, 90º, and 180º, and followed by tensile tests. Yield strength, ultimate tensile strength, elongation, and ultimate tensile strength to yield strength ratio (Rm/Re), were recorded. Results showed the …

A Study On High-Frequency Bending Fatigue, Microhardness, Tensile Strength, And Microstructure Of Parts Made Using Atomic Diffusion Additive Manufacturing (Adam) And Additive Friction Stir Deposition (Afsd), Hamed Ghadimi

LSU Doctoral Dissertations

This dissertation reports the findings of several studies on the mechanical and microstructural properties of parts made using atomic diffusion additive manufacturing (ADAM) and additive friction stir deposition (AFSD). The design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in Chapter 1. The design was optimized based on the finite element analysis and analytical solution. The stress–life (S–N) curve is obtained for Inconel alloy 718. Chapter 2 presents the findings of ultrasonic bending-fatigue and tensile tests carried out on the ADAM test specimens. The S-N curves were created in the very high-cycle fatigue regime. …

Restoration Of Strength In Polyamide Woven Glass Fiber Organosheets By Hot Pressing, Mohammad Nazmus Saquib, Edwing Chaparro-Chavez, Christopher Morris, Kuthan Çelebi, Diego Pedrazzoli, Mingfu Zhang, Sergii G. Kravchenko, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

Thermoplastic composite organosheets (OSs) are increasingly recognized as a viable solution for automotive and aerospace structures, offering a range of benefits including cost-effectiveness through high-rate production, lightweight design, impact resistance, formability, and recyclability. This study examines the impact response, post-impact strength evaluation, and hot-pressing repair effectiveness of woven glass fiber nylon composite OSs across varying impact energy levels. Experimental investigations involved subjecting composite specimens to impact at varying energy levels using a drop-tower test rig, followed by compression-after-impact (CAI) tests. The results underscore the exceptional damage tolerance and improved residual compressive strength of the OSs compared to traditional thermoset composites. …

Strength Comparison For Fully Dense Zirconium Diboride Ceramics Tested By Different Methods, Darko Kosanović, Suzana Filipović, Isaak Trajković, Nina Obradović, Paul M. Brune, Gregory E. Hilmas, William G. Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

The strength of zirconium diboride ceramics was tested by three different methods, 3-point flexure, 4-point flexure, and compression. Nearly full-density ceramics were obtained by hot pressing commercial ZrB₂ powder with the addition of.5 wt.% carbon as a sintering aid. The thermal properties and hardness were studied for ZrB₂ milled with ZrB₂ and WC media. Based on phase purity and higher thermal conductivity, ZrB₂ ceramics prepared from powders milled with ZrB₂ media were selected for mechanical property studies. The strength in 3-point flexure was 546 ± 55 MPa. The flexure strength was 476 ± 41 MPa …

Pressureless Sintering And Properties Of Additively Manufactured Zrb2–Sic, Marharyta Lakusta, Nicholas M. Timme, Jeremy L. Watts, William G. Fahrenholtz, Gregory E. Hilmas, David W. Lipke

Materials Science and Engineering Faculty Research & Creative Works

Densification behavior, grain growth kinetics, mechanical and thermal properties of pressurelessly sintered zirconium diboride–silicon carbide (ZrB2–SiC) fabricated by extrusion of high solids loading pastes have been studied. The effects of sintering temperature (1600–2300°C), heating rate during constant heating rate sintering (10–50°C/min), and time during isothermal sintering (3–24 h) on density and grain size were examined. The apparent activation energy for densification was determined to be 940 ± 90 kJ/mol, suggesting lattice diffusion as the dominant sintering mechanism. Grain growth of both ZrB2 and SiC followed a normal grain growth power law with grain growth exponent n = 2 indicating diffusion-controlled …

The Characterization And Nanomechanical Properties Of Microstructurally Complex Systems, Kerry Ann Baker

Theses and Dissertations--Chemical and Materials Engineering

Since the dawn of civilization, the use of metals has played an integral role in the evolution of human society. Over the years, and with the introduction of new engineering and science, we have learned how to combine metals to create new metallic systems. We have expanded our understanding of dealloying and chemical reactions, and, in doing so, we created nanoporous metals. Our use of metals has evolved from basic alloys such as bronze and steel to more complex alloys such as multi-principal element alloys. Nanoporous gold is an advanced metallic system that can be created through the dealloying process. …

Investigation Of The Effect Of Preparation Parameters On The Structural And Mechanical Properties Of Gelatin/Elastin/Sodium Hyaluronate Scaffolds Fabricated By The Combined Foaming And Freeze-Drying Techniques, Mansour Qamash, S. Misagh Imani, Meisam Omidi, Ciara Glancy, Lobat Tayebi

Electrical & Computer Engineering Faculty Publications

This paper aimed to evaluate the effects of different preparation parameters, including agitation speed, agitation time, and chilling temperature, on the structural and mechanical properties of a novel gelatin/elastin/sodium hyaluronate tissue engineering scaffold, recently developed by our research group. Fabricated using a combination of foaming and freeze-drying techniques, the scaffolds were assessed to understand how these parameters influence their morphology, internal microstructure, porosity, mechanical properties, and degradation behavior. The fabrication process used in this study involved preparing a homogeneous aqueous solution containing 8% gelatin, 2% elastin, and 0.5% sodium hyaluronate (w/v), which was then subjected to mechanical agitation at speeds …

Parametric Optimization Of Friction Stir Welding Of Aa6061-T6 Samples Using The Copper Donor Stir-Assisted Material Method, Aiman H. Al-Allaq, Joseph Maniscalco, Srinivasa Naik Bhukya, Zhenhua Wu, Abdelmageed Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

This study presents an optimization of the process parameters for the effect of copper (Cu) donor material percentage on the friction stir welding (FSW) of AA6061-T6 alloy. Extensive factorial experiments were conducted to determine the significance of the rotational speed (ω), the transverse speed (v), the interface coefficient of friction (μ), and the Cu donor material percentage in the plunge, left, right, and downstream zones. Design Expert 13 software was used to identify the number of simulation experiments to be conducted using the Abaqus simulation software. From Design Expert 13, which is a thorough multi-objective optimization analysis software, we were …

Experimental Characterization And Quantification Of Deformation Behavior In A Porous Carbon Fiber Network, Robert N Quammen

Theses and Dissertations--Chemical and Materials Engineering

Due to their wide range of attractive functional properties (such as low thermal conductivity and low density) porous materials are utilized in a variety of applications. In order to characterize these properties and others, the intrinsically heterogeneous microstructures of these materials need to be taken into account. These microstructures result in interactions across multiple length scales spanning several orders of magnitude. This makes the creation of robust computational models and straight-forward predictions of mechanical properties difficult for porous materials. With this in mind, this dissertation aims to provide experimental mechanical and deformation information spanning the length scales of interest for …

Spatially Resolved Elastic Modulus Of Magnesium Silicate Hydrate: A Cementitious Material, Arif Syed

Material Science and Engineering Theses - Archive

Magnesium-based cements such as magnesium silicate hydrate (MSH) have drawn interest as an environmentally friendly substitute for ordinary Portland cement because of their potential for reduced carbon footprint. The precise determination of these materials' elastic moduli is important to better assess their mechanical performance. Atomic force microscopy (AFM) is an effective tool for precise and spatially resolved quantification of nanomechanical characteristics of materials, including thin films. In this study, elastic modulus maps of MSH grown on single crystal mica surfaces were obtained using amplitude modulation-frequency modulation AFM. The effects of the Mg:Si ratio and morphology on the elastic modulus of …

Analyzing The Effects Of Ultrafast Laser Processing On Mechanical Properties Of 3d-Printed Pla Parts, Darshan Pramodbhai Yadav

Theses and Dissertations

Recent advances in additive manufacturing technologies have already led to wide-scale adoption of 3D-printed parts in various industries. The expansion in choice of materials that can be processed, particularly using Fused Deposition Modeling (FDM), and the steady advancements in dimensional accuracy control have extended the range of applications far beyond rapid prototyping. However, additive manufacturing still has considerable limitations compared to traditional and subtractive manufacturing processes. This work addresses limitations associated with the as-deposited surface roughness of 3D-printed parts. The effects of roughness-induced stress concentrations were studied on ultimate tensile strength and fatigue life. The samples were manufactured using a …

Synergistic Strategies In Sinter-Based Material Extrusion (Mex) 3d Printing Of Copper: Process Development, Product Design, Predictive Maps And Models., Kameswara Pavan Kumar Ajjarapu

Electronic Theses and Dissertations

3D printing pure copper with high electrical conductivity and exceptional density has long been challenging. While laser-based additive manufacturing technologies suffered due to copper's highly reflective nature towards laser beams, parts printed via binder-assisted technologies failed to reach over 90% IACS (International Annealed Copper Standard), electrical conductivity. Although promising techniques such as binder jetting, filament, and pellet-based 3D printing that can print copper exist, they however still face difficulties in achieving both high sintered densities and electrical conductivity values. This is due to a lack of comprehensive understanding of property evolution from green to sintered states and the strategies that …

Effect Of Heating Temperature, Holding Time And Stabilization Temperature On The Al-Foam Properties, Dewi Puspitasari, Poppy Puspitasari, Mazli Mustapha, Turnad Lenggo Ginta

Journal of Mechanical Engineering Science and Technology (JMEST)

The interest in metallic foam is increasing since their cellular structures have a unique combination of properties such as high stiffness, low density, lightweight, high specific strength, and thermal insulation. Commonly, the performance of metallic foam can be improved by the heat treatment process. However, the previous heat treatment methods still present the brittle crack path and the research on heat treatments of the metal foam properties is very limited. In this study, individual parameters in stress relieving treatment that contribute to Al-Foam properties were investigated. The stress-relieving process of the samples was performed using a vacuum furnace. The composition …

Molecular Dynamics Study Of Characterization In Metal-Free Friction Materials, Yizhan Zhang

Electronic Theses and Dissertations

Metallic friction materials currently used in industry may adversely impact the environment. Substitutions for metals in friction materials, on the other hand, can introduce operational safety issues and other unforeseeable issues such as thermal-mechanical instabilities and insufficient strength. In view of it, this dissertation focuses on developing different kinds of materials from simple structure to complex structure and evaluating the material properties with the assistance of molecular dynamics (MD) tools at the nano scale.

First, the concept of the contacted surfaces in friction at the atomic scale was introduced in order to get accurate understanding of the friction process compared …

Analysis Of Bombyx Mori Silk And Polyimide Nanofibers, Sabrina Leseul

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis presents a study on the properties of Bombyx Mori silk nanofibers and polyimide (PI) nanofibers. Firstly, a Bombyx Mori silk solution has been created with degummed silkworm cocoons in order to separate the fibroin and the sericin, the two main proteins of the silk. The fibroin was then centrifuged to remove insoluble particles and stored and 4°C before mixing with hexafluoroisopropanol (HFIP). On the second part, a polyimide solution, made with shavings of polyimide and N,N-dimethylformamide (DMF). Both solutions are then electrospun. Electrospinning parameters are studied. In this way, a part of my thesis has been dedicated to …

Characterization Of Ground Albedo Materials For Bifacial Solar Farms, Fernanda De Los Angeles Garcia, Benny Tam, Jean Lee, James Vance

College of Engineering Summer Undergraduate Research Program

Bifacial photovoltaics can collect solar energy from both sides, unlike regular one-sided solar panels. With the ability to collect energy from both sides, the energy production of bifacial photovoltaic farms is about 2-6% more efficient than typical solar farms. However, the increase in efficiency is highly dependent on the reflectivity of the ground material. This project explores six different materials to determine which material would be best to implement as a ground material for a bifacial photovoltaic farm, based on their mechanical properties and albedo value. Albedo refers to the ratio between the reflected solar radiation to the incident solar …

Retracted: Fabrication And Characterization Of Wood Fiber Reinforced Polymer Composites, Firoz Ahmed, Omar Faroque, Saif Hasan, Khan Rajib Hossain, Rezaul Karim Sheikh

Al-Bahir

Wood-polymer composites (WPCs) combine the properties of wood and polymers. Creating composites involves adding plant or wood fibers as fillers to a polymer matrix. This study used mahogany and mango wood sawdust as reinforcement materials, while high-density polyethylene (HDPE) and polyvinyl chloride (PVC) were used as matrices. The investigated data in this study comprises four different (10, 20, 30, and 40) weight percentages (wt%) of mahogany and mango sawdust paired with corresponding wt% (90, 80, 70, and60) of HDPE and PVC matrices. The extrusion method produced composites with different amounts of sawdust and polymer matrices. Wood polymer composites were characterized …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario F. Buchely, Ronald J. O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the Face-Centered Cubic (FCC) Multi-Principal Element Alloys (MPEAs) Developed Thus Far Contain Cobalt. for Many Applications, it is Either required or Beneficial to Avoid Cobalt, Since Cobalt Has Long-Term Activation Issue (For Nuclear Applications), is Expensive, and is Considered a Critical Material. in Addition, FCC Structured Solid-Solution MPEAs Tend to Have Relatively Low Strength. a FCC Solid-Solution Fe30Ni30Mn30Cr10 (At %) MPEA Was Fabricated Via Arc Melting, Followed by Homogenization at 1100 °C for 12 H. the Alloy Was Hot Rolled at 1100 °C with a Total Reduction of Up to 97 %. the Microstructure Was Characterized and Mechanical …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …

Enhancing Compatibility And Mechanical Properties Of Natural Rubber Composites, Krisma Yessi Sianturi, Adam Febriyanto Nugraha, Belle Kristaura, Mochamad Chalid

Journal of Materials Exploration and Findings

Pure natural rubber (NR) exhibits low mechanical properties, necessitating the incorporation of additives like vulcanizing agents and fillers. Carbon black and silica, conventional fillers, are relatively expensive and not environmentally friendly. This study explores using Oil Palm Empty Fruit Bunch (OPEFB) fiber as an affordable, abundant, and biodegradable alternative filler for NR. However, compatibility issues arise between the nonpolar NR and the polar OPEFB fiber. A latex-starch hybrid coupling agent (CA (NR-St)) was added to the composite formulation to address this. NR, OPEFB fiber, and the coupling agent were mixed using an open roll mill with a 10 phr OPEFB …

A High-Strength Precipitation Hardened Cobalt-Free High-Entropy Alloy, Matthew Luebbe, Jiaqi Duan, Fan Zhang, Jonathan Poplawsky, Hans Pommeranke, Maalavan Arivu, Andrew Hoffman, Mario Buchely, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. a Co-free (Fe0.3Ni0.3Mn0.3Cr0.1)88Ti4Al8 HEA was developed and studied in this work. in contrast to previous Co-free HEAs, this alloy is close to Equi atomic in its composition and promises a more …

Nanoclays‑Containing Bio‑Based Packaging Materials: Properties, Applications, Safety, And Regulatory Issues, Kalpani Y. Perera, Maille Hopkins, Amit K. Jaiswal Dr, Swarna Jaiswal

Articles

Food packaging is an important concept for consumer satisfaction and the increased shelf life of food products. The introduction of novel food packaging materials has become an emerging trend in recent years, which could be mainly due to environmental pollution caused by plastic packaging and to reduce food waste. Recently, numerous studies have been carried out on nanoclays or nanolayered silicate to be used in packaging material development as reinforcing filler composites. Different types of nanoclays have been used as food packaging materials, while montmorillonite (MMT), halloysite, bentonite (BT), Cloisite, and organically modified nanoclays have become of great interest. The …

Mechanical Properties Of Zrb2 Ceramics Determined By Two Laboratories, Jeffrey J. Swab, Jecee Jarman, William Fahrenholtz, Jeremy Lee Watts

Materials Science and Engineering Faculty Research & Creative Works

The mechanical properties for zirconium diboride (ZrB2) were measured at two laboratories and compared. Two billets of ZrB2 were prepared by hot-pressing commercial powder. The relative densities of the billets were >99% and with an average grain size of 5.9 ± 4.5 µm. Both laboratories prepared American Society for Testing and Materials (ASTM) C1161 B-bars for strength and ASTM C1421 bars with notch configuration A for fracture toughness. Specimens were machined by diamond grinding at the Army Research Laboratory (ARL) and electrical discharge machining (EDM) at Missouri S&T. Strength bars tested at Missouri S&T were polished to a.25 μm finish …

Effect Of Mechanical Activation On Carbothermal Synthesis And Densification Of Zrc, Nina Obradović, Lun Feng, Suzana Filipović, Miljana Mirković, Darko Kosanović, Jelena Rogan, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

Zirconium carbide ceramics were prepared by carbothermal reduction of ZrO₂ and C that were mixed by high-energy ball milling. Powders were milled for times from 0 to 120 min in air. As milling time increased, the surface area of the powders increased, indicating significant particle size reduction. Milled powders were reacted at 1600 °C and then densified by spark plasma sintering at 2000 °C, which was sufficient to convert the starting powders to zirconium carbide. Unmilled powders did not reach full density. Milled powders reached full density, but ZrO₂ impurities were found for specimens prepared from powders milled …

Strength Retention Of Single-Phase High-Entropy Diboride Ceramics Up To 2000°C, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Yue Zhou, Jincheng Bai

Materials Science and Engineering Faculty Research & Creative Works

The mechanical properties of single-phase (Hf_0.2,Nb_0.2,Ta_0.2,Ti_0.2,Zr_0.2)B₂ ceramics with high purity were investigated. The resulting ceramics had relative density greater than 99%, and an average grain size of 4.3 ± 1.6 μm. At room temperature (RT), the Vickers hardness was 25.2 ± 0.6 GPa at a load of 0.49 N, Young's modulus was 551 ± 7 GPa, fracture toughness was 4.5 ± 0.4 MPa m1/2, and flexural strength was 507 ± 10 MPa. Flexural strength increased by more than 50% from 507 ± 10 MPa at RT to 776 ± …

Solid-State Electrolytes For Long Duration Molten Sodium Batteries, Ryan C. Hill

Theses and Dissertations--Chemical and Materials Engineering

Rechargeable batteries have become a staple of modern society, driving the development and expansion of portable electronics and electric vehicles. The long lifetime and high energy density provided by batteries have made them excellent candidates for use in the emerging field of long duration, grid-scale energy storage. However, traditional battery chemistries, such as Li-ion, are not an ideal solution for grid-scale storage, due to high-cost raw materials that are often sourced from volatile markets. Sodium-based batteries are a promising alternative for long duration storage, owing to the domestic abundance of raw materials and energy densities that nearly rival that of …

Processing And Mechanical Properties Of Hot-Pressed Zirconium Diboride – Zirconium Carbide Ceramics, Eric W. Neuman, William Fahrenholtz, Gregory E. Hilmas

Materials Science and Engineering Faculty Research & Creative Works

ZrB2 was mixed with 0.5 wt% carbon and up to 10 vol% ZrC and densified by hot-pressing at 2000 °C. All compositions were > 99.8% dense following hot-pressing. The dense ceramics contained 1–1.5 vol% less ZrC than the nominal ZrC addition and had between 0.5 and 1 vol% residual carbon. Grain sizes for the ZrB2 phase decreased from 10.1 µm for 2.5 vol% ZrC to 4.2 µm for 10 vol% ZrC, while the ZrC cluster size increased from 1.3 µm to 2.2 µm over the same composition range. Elastic modulus was ~505 GPa and toughness was ~2.6 MPa·m½ for all compositions. …

Effect Of Boron In Cast Iron, Suyash Durendra Pawaskar

Masters Theses

"Boron, mostly considered a residual element, has started to cause issues in the cast iron foundries by causing a decrease in the strength of pearlitic gray and ductile iron castings. Because of the increase in the use of boron-added steel scrap from automotive steel and a lack of agreement on the critical levels of boron in cast iron, foundries are facing difficulties in controlling the microstructure of gray iron castings when boron is present. The current investigation was designed to analyze the effects of boron in cast irons and predict a mechanism to understand its effects with a vision of …

Mechanical Properties And Microstructure Of High Strength Lc3 Pastes With Varying Limestone/Calcined Clay Ratios And Different Curing Conditions, Yemin Dong

International Conference on Durability of Concrete Structures

研究（抗施工蒸馏）石石和石榴石在淀粉胶系统（即0标准和低水印）下的水胶系统（即0标准和低水墨）X射线比、水量值水量-电子背基相关研究.61.25 .25.25.25.0.25.25.25.25.25.0.25.25.25.25.25.1.25.7.25.0.0.0.0.0.0.0.0.0.0.0.0.0.0.1.25.1.25.25.1.25.1.25.1.25.1.25.1.25.1 .25.1.25.1.25.1.25.1.25.1.25.0.0.0.0.0.0.0.00.0.0.1.25.1.25.1.25.1.25.1.25.0.0.0.00.0.0.0.0.0.0.0.0.0.0.0.0.0.00.0 .00.0.00.X射线比值、水量-电子显微镜相关研究测量值。早期的水泥水化程度小水的压合含煤量，降低了水泥石的。因此，需要采用合适的钙铝内容和体系以提高碳系统的性能。