Materials Science and Engineering Commons^™

Corrosion Behaviour Of Aisi 304 Stainless Steel In Contact With Eutectic Salt For Concentrated Solar Power Plant Applications, Omar Ahmed

Electronic Theses and Dissertations

In response to the extensive energy demands on national and global levels, concentrated solar power (CSP) plants are designed to harness and convert solar energy to electricity. For such green energy application, robust, reliable and durable materials for CSP constructions are required. The corrosion resistance is among many parameters to consider in these thermalelectrical stations such as for pipes and storage tanks in CSP. In this investigation, the corrosion behavior of AISI 304 stainless steel (18 wt. % Cr, 8 wt. % Ni) with the heat transfer fluid, also known as solar salt, has been examined. The ternary eutectic salt …

Interdiffusion And Impurity Diffusion In Magnesium Solid Solutions, Catherine Kammerer

Electronic Theses and Dissertations

Magnesium, being lightweight, offers potential to be developed into extensive structural applications. The transportation segment has particular interest in Mg and Mg alloy for applications where reduced vehicle weight is proportional to increased fuel efficiency. Aluminum and zinc are two of the most common alloying elements in commercial Mg alloys. They improve the physical properties of Mg through solid solution strengthening and precipitation hardening. Diffusion plays a key role in the kinetics of and microstructural development during solidification and heat treatment. However, there is limited diffusion data available for Mg and Mg alloys. In particular, because Al is monoisotopic, tracer …

Development Of Nitrogen Concentration During Cryomilling Of Aluminum Composites, Clara Hofmeister

Electronic Theses and Dissertations

The ideal properties of a structural material are light weight with extensive strength and ductility. A composite with high strength and tailorable ductility was developed consisting of nanocrystalline AA5083, boron carbide and coarser grained AA5083. The microstructure was determined through optical microscopy and transmission electron microscopy. A technique was developed to determine the nitrogen concentration of an AA5083 composite from secondary ion mass spectrometry utilizing a nitrogen ionimplanted standard. Aluminum nitride and amorphous nitrogen-rich dispersoids were found in the nanocrystalline aluminum grain boundaries. Nitrogen concentration increased as a function of cryomilling time up to 72hours. A greater nitrogen concentration resulted …

Nano-Morphology Of Polymer Bulk Herojunctions Studied By Time-Resolved Synchrotron X-Ray Scattering, Soo Kim

Material Science and Engineering Dissertations - Archive

This study investigates the phase transformation of an active layer in organic photovoltaics (OPV) during film deposition and post thermal treatment as well as effects of phase transformation on OPV performance. For this purpose, small - and wide angle X-ray scattering technique (SAXS and WAXS) was applied to examine the phase separation mechanism at relevant fabrication condition of the highest OPV device performance. The poly(3-alkylthiophene)/[6,6]-phenyl-C61 butyric acid methylester (P3AT/PCBM) blend sample was employed in order to study phase transformation of the active layer systemically.Our exploration with SAXS and WAXS technique found that the polarity of the substrate, a solubility, and …

Fabrication And Characterization Of Barium Titanate Thin Film On Polycrystalline Nickel Substrate, Parisa Sahebi

Material Science and Engineering Theses - Archive

Ferroelectric BaTiO₃(BTO) thin films were deposited on polycrystalline nickel disks and silicon wafer substrates by rf magnetron sputtering. Nickel oxide (NiO) and nanocrystalline nickel (nc-Ni) layers were used as interfacial buffer layers. Microstructural studies with X-ray diffraction and transmission electron microscopy reveal that the BTO films deposited at temperatures lower than 700℃ have an amorphous structure. However, the BTO films sputtered at temperatures higher than 700℃ are partially crystalline. BTO films have a good and continuous interface with both interfacial layers with no interdiffusion or reaction with the substrates. In the case of BTO deposition with nc-Ni interlayer at higher …

Effect Of Microwave Heating On The Migration Of Additives From Ps, Pp And Pet Container Into Food Simulants, Ruoyin Cai

Theses

Microwave food packaging has become a tremendous element in the food manufacturing process. The purpose of any food packaging regulations concerned with the safety of the food is to control and limit the migration of substances from the packaging into the food. The main objective of this thesis is to test three different microwaving packaging materials that are the most common material in the market, viz. polystyrene (PS), polypropylene (PP), and polyethylene terephthalate (PET), migrated into four food simulant solutions. Four different simulant solutions were used based on the food type and FDA recommendations and regulations. These food simulants include …

Fabricating And Characterizing Physical Properties Of Electrospun Polypeptide-Based Nanofibers, Dhan Bahadur Khadka

USF Tampa Graduate Theses and Dissertations

This dissertation has aimed to fabricate polypeptide based biomaterial and characterize physical properties. Electrospinning is used as a tool for the sample fabrication. Project focused on determining the feasibility of electrospinning of certain synthetic polypeptides and certain elastin-like peptides from aqueous feedstocks and to characterize physical properties of polymer aqueous solution, cast film and spun fibers and fiber mats. The research involves peptide design, polymer electrospinning, fibers crosslinking, determining the extent of crosslinking, fibers protease degradation study, fibers stability and self-organization analysis, structure and composition determination by various spectroscopy and microscopy techniques and characterization of mechanical properties of individual suspended …

Evaluating Cfrp-Masonry Bond Using Thermal Imaging, Joseph Christopher Ross

USF Tampa Graduate Theses and Dissertations

This study presents results from non-destructive testing to evaluate the degradation of the CFRP-masonry bond using thermal imaging. The goal of the research was to identify locations where there was evidence of bond deterioration that could subsequently be verified through destructive pull-off testing.

Four full-scale masonry walls were built outdoors at the University of South Florida in 1995 to evaluate the effectiveness of CFRP for repairing settlement damage. Two of the settlement-damaged walls were repaired using single layer, commercially available unidirectional CFRP systems that used Tonen (wall 3) and Henkel (wall 2) epoxies. These two walls were the subject of …

Kelvin Probe Electrode For Contactless Potential Measurement On Concrete-Properties And Applications, Michael Thomas Walsh

USF Tampa Graduate Theses and Dissertations

The practical feasibility of using a Kelvin Probe as a novel reference electrode in the measurement of both potential and polarization pulse response of reinforcing steel in concrete is demonstrated. Potential values measured using a KP reflect greater stability and repeatability than can typically be attained with conventional reference electrodes. Duplicate reinforced concrete beam test specimens with well-differentiated centrally corroding rebar segments were analyzed using both the Kelvin Probe (KP) and a conventional Saturated Calomel Electrode (SCE). Potential profile maps were developed using potential values recorded under static conditions with both the SCE and the KP. Nominal polarization resistance was …

Development Of Nanostructured Graphene/Conducting Polymer Composite Materials For Supercapacitor Applications, Punya A. Basnayaka

USF Tampa Graduate Theses and Dissertations

The developments in mobile/portable electronics and alternative energy vehicles prompted engineers and researchers to develop electrochemical energy storage devices called supercapacitors, as the third generation type capacitors. Most of the research and development on supercapacitors focus on electrode materials, electrolytes and hybridization. Some attempts have been directed towards increasing the energy density by employing electroactive materials, such as metal oxides and conducting polymers (CPs). However, the high cost and toxicity of applicable metal oxides and poor long term stability of CPs paved the way to alternative electrode materials. The electroactive materials with carbon particles in composites have been used substantially …

Corrosion Of Post-Tensioning Strands In Ungrouted Ducts - Unstressed Condition, Michael John Hutchison

USF Tampa Graduate Theses and Dissertations

Recent failures and severe corrosion distress of post-tensioned (PT) bridges in Florida have revealed corrosion of the 7-wire strands in tendons. Post-tensioned duct assemblies are fitted with multiple 7-wire steel strands and ducts are subsequently filled with grout. During construction, the length of time from the moment in which the strands have been inserted into the ducts, until the ducts are grouted, is referred to as the `ungrouted' period. During this phase, the steel strands are vulnerable to corrosion and consequently the length of this period is restricted (typically to 7 days) by construction guidelines. This investigation focuses on determining …

Synthesis And Investigations Of Type I And Ii Clathrates Of Group 14, Michael Blosser

USF Tampa Graduate Theses and Dissertations

Clathrates are a class of new materials that have an open-framework structure that allows guest atoms or molecules to be enclosed inside of their polyhedral framework. Varying the number, weight, and size of the guest species in a particular framework allows one to alter the physical properties of the clathrate. This relationship enables one to further the fundamental understanding of the physics and chemistry of the clathrate structure and use this knowledge to "tune" certain properties. This "tunability" of inorganic clathrates is of great interest as it allows one to optimize their physical properties; making them promising candidates for a …

Effect Of Cement Chemistry And Properties On Activation Energy, Andre J. Bien-Aime

USF Tampa Graduate Theses and Dissertations

The objective of this work is to examine the effect of cement chemistry and physical properties on activation energy. Research efforts indicated that time dependent concrete properties such as strength, heat evolution, and thermal cracking are predictable through the concept of activation energy. Equivalent age concept, which uses the activation energy is key to such predictions. Furthermore, research has shown that Portland cement concrete properties are affected by particles size distribution, Blaine fineness, mineralogy and chemical composition. In this study, four Portland cements were used to evaluate different methods of activation energy determination based on strength and heat of hydration …

Analytical And Numerical Modeling Of Assembly Procedures Of Steel Fulcra Of Bascule Bridges, Sriharsha Garapati

USF Tampa Graduate Theses and Dissertations

To model shrink-fitting in metal components, an analytical model for two long compound cylinders with temperature dependent material properties and interference between them is developed for calculating transient temperatures and stresses. A finite element model is developed for the same geometry which incorporated the temperature dependent material properties. A convergence study is performed on the finite element and analytical model. The finite element model is validated by comparing the approximations of finite element model with the analytical solution.

In an assembly procedure of fulcrums for bascule bridges, called AP1, the trunnion is shrink-fitted into a hub, followed by shrink fitting …

Structured Materials For Catalytic And Sensing Applications, Selma Hokenek

USF Tampa Graduate Theses and Dissertations

The optical and chemical properties of the materials used in catalytic and sensing applications directly determine the characteristics of the resultant catalyst or sensor. It is well known that a catalyst needs to have high activity, selectivity, and stability to be viable in an industrial setting. The hydrogenation activity of palladium catalysts is known to be excellent, but the industrial applications are limited by the cost of obtaining catalyst in amounts large enough to make their use economical. As a result, alloying palladium with a cheaper, more widely available metal while maintaining the high catalytic activity seen in monometallic catalysts …

Mse Annual Report 2013, Department Of Materials Science And Engineering, Michigan Technological University

Department of Materials Science and Engineering Annual Reports

Table of Contents

• Paul Sanders, Project-Oriented Learning
• A New Way to Prevent Deadly Infections
• 3D Printers for Peace and Progress
• Faculty and Staff News
• Graduate Student Update
• Outreach
• Undergraduate Student News
• Alumni at a Glance

Faulted Structures In Li Ion Exchanged Namo2 (M=Ni(0.25)Mn(0.75)), Aaron M. Dewahl

Dissertations, Master's Theses and Master's Reports - Open

A family of LiMO2 materials (M=Ni_0.25Mn_0.75) was prepared from Na_1.2-xLi_xMO_∂ precursors (0≤x≤0.6) via ion exchange. The resulting IE products were examined via XRD and compared to simulated XRD patterns produced using DIFFax to determine the defect structures resulting from the IE process. For the 0.1≤x≤0.6 materials, it is observed that there are 3 LiMO₂ sub-phases with different Li contents present. As the amount of Li in the precursor increases, the amount of each phase changes resulting in a net shift to higher 2-theta; corresponding to an overall decrease in lattice …

An Investigation Of Waste Glass-Based Geopolymers Supplemented With Alumina, Mary U. Christiansen

Dissertations, Master's Theses and Master's Reports - Open

An increased consideration of sustainability throughout society has resulted in a surge of research investigating sustainable alternatives to existing construction materials. A new binder system, called a geopolymer, is being investigated to supplement ordinary portland cement (OPC) concrete, which has come under scrutiny because of the CO2 emissions inherent in its production.

Geopolymers are produced from the alkali activation of a powdered aluminosilicate source by an alkaline solution, which results in a dense three-dimensional matrix of tetrahedrally linked aluminosilicates. Geopolymers have shown great potential as a building construction material, offering similar mechanical and durability properties to OPC. Additionally, geopolymers have …

Molecular Modeling Of Pmr-15 Polyimide, Fnu Pruthul Kokkada Ravindranath

Dissertations, Master's Theses and Master's Reports - Open

PMR-15 polyimide is a polymer that is used as a matrix in composites. These composites with PMR-15 matrices are called advanced polymer matrix composite that is abundantly used in the aerospace and electronics industries because of its high temperature resistivity. Apart from having high temperature sustainability, PMR-15 composites also display good thermal-oxidative stability, mechanical properties, processability and low costs, which makes it a suitable material for manufacturing aircraft structures. PMR-15 uses the reverse Diels-Alder (RDA) method for crosslinking which provides it with the groundwork for its distinctive thermal stability and a range of 280-300 degree Centigrade use temperature. Regardless of …

Dysprosium Transport In Nd-Fe-B Pellets, Parawee Pumwongpitak

Dissertations, Master's Theses and Master's Reports - Open

The addition of heavy rare earth (RE) elements to Nd2Fe14B based magnets to form (Nd,Dy)₂Fe₁₄B is known to increase the coercivity and high temperature performance required for hybrid vehicle electric motors and other extreme temperature applications. Attempts to conserve heavy rare earth elements for high temperature (RE)₂Fe₁₄B based magnets have led to the development of a grain boundary diffusion process for bulk magnets. This process relies on transport of a heavy rare earth, such as Dy, into a bulk Nd₂Fe₁₄B magnet along pores, a low volume fraction of …

Parametric Study Of Reaxff Simulation Parameters For Molecular Dynamics Modeling Of Reactive Carbon Gases, Benjamin David Jensen

Dissertations, Master's Theses and Master's Reports - Open

Abstract

Intergranular Corrosion And Stress Corrosion Cracking Of Extruded Aa6005a, David James Seguin

Dissertations, Master's Theses and Master's Reports - Open

A research program focused on understanding the intergranular corrosion (IGC) and stress corrosion cracking (SCC) behavior of AA6005A aluminum extrusions is presented in this dissertation. The relationship between IGC and SCC susceptibility and the mechanisms of SCC in AA6005A extrusions were studied by examining two primary hypotheses.

IGC susceptibility of the elongated grain structure in AA6005A exposed to low pH saltwater was found to depend primarily on the morphology of Cu-containing precipitates adjacent to the grain boundaries in the elongated grain structure. IGC susceptibility was observed when a continuous (or semi-continuous) film of Cu-containing phase was present along the grain …

Accurate Prediction Of Spectral Phonon Relaxation Time And Thermal Conductivity Of Intrinsic And Perturbed Materials, Tianli Feng

Open Access Theses

The prediction of spectral phonon relaxation time, mean-free-path, and thermal conductivity can provide significant insights into the thermal conductivity of bulk and nanomaterials, which are important for thermal management and thermoelectric applications. We perform frequency-domain normal mode analysis (NMA) on pure bulk argon and pure bulk germanium. Spectral phonon properties, including the phonon dispersion, relaxation time, mean free path, and thermal conductivity of argon and germanium at different temperatures have been calculated. We find the dependence of phonon relaxation time τ on frequency ω and temperature T vary from ~ω^-1.3 to ~ω^-1.8 and ~T^-0.8 to ~T^{-1.8 …}

High Speed Turning Of Compacted Graphite Iron (Cgi) Using Controlled Modulation, Tyler Paul Stalbaum

Open Access Theses

Compacted graphite iron (CGI) is a material which emerged as a candidate material to replace cast iron (CI) in the automotive industry for engine block castings. Its thermal and mechanical properties allow the CGI-based engines to operate at higher cylinder pressures and temperatures than CI-based engines, allowing for lower fuel emissions and increased fuel economy. However, these same properties together with the thermomechanical wear mode in the CGI-CBN system result in poor machinability and inhibit CGI from seeing wide spread use in the automotive industry.

In industry, machining of CGI is done only at low speeds, less than V = …

Rapid Repair Of Severely Damaged Rc Columns With Different Damage Conditions: An Experimental Study, Ruili He, Lesley Sneed, Abdeldjelil Belarbi

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.

Applications Of High Throughput (Combinatorial) Methodologies To Electronic, Magnetic, Optical, And Energy-Related Materials, Martin L. Green, Ichiro Takeuchi, Jason R. Hattrick-Simpers

Faculty Publications

High throughput (combinatorial) materials science methodology is a relatively new research paradigm that offers the promise of rapid and efficient materials screening, optimization, and discovery. The paradigm started in the pharmaceutical industry but was rapidly adopted to accelerate materials research in a wide variety of areas. High throughput experiments are characterized by synthesis of a “library” sample that contains the materials variation of interest (typically composition), and rapid and localized measurement schemes that result in massive data sets. Because the data are collected at the same time on the same “library” sample, they can be highly uniform with respect to …

A Laboratory Experiment Using Nanoindentation To Demonstrate The Indentation Size Effect, Wendelin Wright, Gang Feng, William D. Nix

Faculty Journal Articles

A laboratory experiment using nanoindentation to demonstrate the indentation size effect is described. This laboratory introduces students to sophisticated instrumentation at low cost and low risk and utilizes recent research in the materials community as its foundation. The motivation, learning objectives, experimental details, data, and data analysis are presented. This experiment is intended for use in an upper-division materials science elective at the university level and has been successfully used in laboratory courses for senior undergraduates and first-year graduate students at Stanford University and Santa Clara University.

The Processing Of Aluminum Gasarites Via Thermal Decomposition Of Interstitial Hydrides, Joseph James Licavoli

Dissertations, Master's Theses and Master's Reports - Open

Gasarite structures are a unique type of metallic foam containing tubular pores. The original methods for their production limited them to laboratory study despite appealing foam properties. Thermal decomposition processing of gasarites holds the potential to increase the application of gasarite foams in engineering design by removing several barriers to their industrial scale production. The following study characterized thermal decomposition gasarite processing both experimentally and theoretically. It was found that significant variation was inherent to this process therefore several modifications were necessary to produce gasarites using this method. Conventional means to increase porosity and enhance pore morphology were studied. Pore …

The Use Of Elemental Powder Mixes In Laser-Based Additive Manufacturing, Rodney Michael Clayton

Masters Theses

"This study examines the use and functionality of laser depositing alloys from mixes of elemental metallic powders. Through the use of laser-based additive manufacturing (LAM), near net-shaped 3-Dimensional metallic parts can be produced in a layer-by-layer fashion. It is customary for pre-alloyed powders to be used in this process. However, mixes of elemental powders can be used to produce alloys that are formed during the deposition process. This alternative technique requires that the elemental powders adequately mix during deposition for a homogeneous deposit to be produced. Cost savings and versatility are among several of the advantages to using elemental powder …

Liquid Phase Sintering Of 20bi(Zn₀.₅Ti₀.₅)O₃-80batio₃ Dielectrics With Bismuth-Zinc-Borate And Bismuth Borosilicate Glasses, David I. Shahin

Masters Theses

"Dielectrics in the Bi(Zn₀.₅Ti₀.₅O₃-BaTiO₃ system (specifically 20BZT-80BT, in mol%) are promising candidates for high energy density capacitor applications due to broad temperature-dependent dielectric constant maxima and a relatively field-independent permittivity. Bulk samples require sintering temperatures of greater than 1180ºC to reach useful densities. Due to incompatibility of Bi with low-pO₂ processing, BZT-BT-based multilayer capacitors must utilize noble metal electrodes that resist oxidation during sintering. Sintering temperatures must be reduced to allow use of less expensive electrode materials (Cu, etc.). This work studies the reduced temperature sintering behavior and dielectric properties of BZT-BT sintered with 30 Bi₂O₃-30ZnO-40B₂O₃ and 50Bi₂O₃-25B₂O₃-25SiO₂ (mol%) liquid …