Materials Science and Engineering Commons^™

Artificial Neural Network Modeling Of Rf Mems Resonators, Yongjae Lee, Yonghwa Park, Feng Niu, Bonnie Bachman, K. C. Gupta, Dejan Filipovic

Economics Faculty Research & Creative Works

In this article, a novel and efficient approach for modeling radio‐frequency microelectromechanical system (RF MEMS) resonators by using artificial neural network (ANN) modeling is presented. In the proposed methodology, the relationship between physical‐input parameters and corresponding electrical‐output parameters is obtained by combined circuit/full‐wave/ANN modeling. More specifically, in order to predict the electrical responses from a resonator, an analytical representation of the electrical equivalent‐network model (EENM) is developed from the well‐known electromechanical analogs. Then, the reduced‐order, nonlinear, dynamic macromodels from 3D finite‐element method (FEM) simulations are generated to provide training, validating, and testing datasets for the ANN model. The developed ANN …

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2004 Through June 30, 2004, Anthony Hechanova

Publications (NSTD)

UNLV hosted a meeting on NHI Materials and Heat Exchanger Design on Monday, May 17. Paul Pickard (Sandia National Lab) and Bill Corwin (Oak Ridge National Lab) facilitated the meeting. The purpose of the meeting was to summarize the hydrogen materials and heat exchanger requirements and priorities for UNLV staff and their collaborators to support the research proposal solicitation for the UNLV Research Foundation HTHX program. Attendance was heavier than anticipated and required a change of venue to accommodate the crowd of over 30.

Use Of Collaborative Learning Exercises To Increase Student Motivation And Learning In An Introduction To Materials Engineering Course, Stacy Gleixner, Hilary Lackritz

Faculty Publications

A collection of collaborative, in-class exercises have been designed for use in a freshmen/sophomore level Introduction to Materials Science and Engineering class. The activities are team based problems that include open ended design problems, calculation questions, and thought problems on unanswered research questions. The activities have been designed with the goal of having one or two a week embedded in a more traditional lecture setting. The exercises relate to the topics covered in most standard Introduction to Materials classes (crystal structure, mechanical properties, polymers, phase diagrams…). Each activity is designed specifically to engage the students in the lecture and excite …

Travelogue From The Materials World: A First Week Laboratory Activity, Katherine C. Chen, Blair London, Linda Vanasupa, Timothy T. Orling, Lisa Christensen

Materials Engineering

A fun, yet educational, laboratory activity was developed for the first week of an introductory Materials Engineering laboratory in order to set the stage for the rest of the quarter. The class is broken up into 8 teams, and each team performs a different experiment during each lab period. The teams then rotate lab experiments each week in a round robin manner, and thus teamwork is an important component of the class. In order to quickly promote team bonding the very first week, each team goes on a materials scavenger hunt together. A variety of materials-related items are to be …

Interactive Demonstrations And Laboratories Using Shape Memory Alloys, Wendy C. Crone, Eric J. Voss, Katherine C. Chen

Materials Engineering

Shape memory alloys (SMAs) constitute a unique class of materials that undergo a reversible phase transformation allowing the material to display dramatic stress-induced and temperature-induced deformations that are recoverable. Nickel titanium (NiTi) is a shape memory alloy used in a wide variety of biomedical, aerospace, automotive and other applications. The austenite-martensite phase transformation that occurs in these alloys with changes in temperature or applied stress is responsible for the unique properties of this material. The unusual behavior of SMAs provides an exciting way to engage students and can be incorporated into a variety of courses under topics such as phase …

The Structure Of The High-Energy Spin Excitations In A High-Transition-Temperature Superconductor, S. M. Hayden, H. A. Mook, Pengcheng Dal, T. G. Perring, F. Doǧan

Materials Science and Engineering Faculty Research & Creative Works

In conventional superconductors, lattice vibrations (phonons) mediate the attraction between electrons that is responsible for superconductivity. The high transition temperatures (high-Tc) of the copper oxide superconductors has led to collective spin excitations being proposed as the mediating excitations in these materials. The mediating excitations must be strongly coupled to the conduction electrons, have energy greater than the pairing energy, and be present at Tc. The most obvious feature in the magnetic excitations of high-Tc superconductors such as YBa 2Cu3O6+x is the so-called 'resonance'. Although the resonance may be strongly coupled to the superconductivity, it is unlikely to be the main …

The Influence Of Academic Dishonesty On Ethical Decision- Making In The Workplace: A Study Of Engineering Students, Trevor S. Harding, Donald D. Carpenter, Cynthia J. Finelli, Honor J. Passow

Materials Engineering

According to studies conducted over the past four decades, engineering students self-report high frequencies of academic dishonesty (cheating) while in college. Research on college students in all fields has indicated that such behavior is more common among students who participate in academic dishonesty at the high school level and that it is correlated with other deviant or unethical behaviors, such as petty theft and lying. If, in fact, such correlations do exist, one might hypothesize that there is also a relationship between academic dishonesty in college and deviant or unethical behavior in professional practice. Placing this relationship in the context …

Life Cycle Assessment As A Tool For Green Manufacturing Education, Trevor S. Harding

Materials Engineering

The design and production of engineering products that have a reduced impact on the environment and human health has increasingly become a strategic goal of corporations. Consequently, starting engineers will need to be educated in green design techniques. One method that is particularly attractive to engineers is Life Cycle Assessment (LCA). LCA is an objective approach to evaluating the environmental burden of a product, process or activity by identifying and quantifying material and energy usage and waste outputs at every life stage. LCA involves three steps: identification of scope of analysis, life cycle inventory, and impact analysis. Such an approach …

Does Academic Dishonesty Relate To Unethical Behavior In Professional Practice? An Exploratory Study, Trevor S. Harding, Donald D. Carpenter, Cynthia J. Finelli, Honor J. Passow

Materials Engineering

Previous research indicates that students in engineering self-report cheating in college at higher rates than those in most other disciplines. Prior work also suggests that participation in one deviant behavior is a reasonable predictor of future deviant behavior. This combination of factors leads to a situation where engineering students who frequently participate in academic dishonesty are more likely to make unethical decisions in professional practice. To investigate this scenario, we propose the hypotheses that (1) there are similarities in the decision-making processes used by engineering students when considering whether or not to participate in academic and professional dishonesty, and (2) …

Synchronous Motor Phase Control By Vector Addition Of Induced Winding Voltages, Daniel J. Simon, Dennis L. Feucht

Electrical and Computer Engineering Faculty Publications

We propose a simple low-cost approach to the winding-sensed control of three-phase synchronous permanent-magnet motors. Our approach results from a straightforward but elegant application of vector-based motor theory. The method therefore does not depend on the differential equations that describe the motor dynamics, and it does not depend on the particular motor parameters. The single method we derive applies to both wye- and delta-configured motors. We vectorially sum the voltage waveforms at the motor terminals in a certain way and use their zero crossings to produce a correctly phased six-step switch sequence. We discuss the implementation for both wye- and …

Structural And Magnetic Properties Of Mrsr₂Y₁.₅Ce₀.₅Cu₂Oz (M-1222) Compounds With M = Fe And Co, V. P. S. Awana, Anurag Gupta, H. Kishan, Satish K. Malik, William B. Yelon, J. Lindén, M. Karppinen, H. Yamauchi, Darshan C. Kundaliya

Physics Faculty Research & Creative Works

The MSr2Y1.5Ce0.5Cu2Oz (M-1222) compounds, with M = Fe and Co, have been synthesized through a solid-state reaction route. Both compounds crystallize in a tetragonal structure (space group 14/mmm). A Rietveld structural refinement of the room-temperature neutron diffraction data for Fe-1222 reveals that nearly half the Fe remains at the M site, while the other half goes to the Cu site in the CuO2 planes. Existence of Fe at two different lattice sites is also confirmed by 57Fe Mössbauer spectroscopy from which it is inferred that ~50% of the total Fe occupies the Cu site in the CuO2 planes as Fe3+, …

Crystallization Kinetics Study Of The Glasses In Se–Te System, Fareed Abdul Raheem Al-Gheyath

Theses

The aim of the present work is to study the crystallization kinetics of some chalcogenide glassy alloys in the Selenium-Tellurium system. Four glassy systems have been prepared: Se₈₀Te_20-xSb_x (x= 0, 4, 6, 8, and 10); Se₇₀Te_30-xSb_x (x= 2, 6, 8, and 10); Se₈₀Te_20-xCd_x (x= 2, 4, and 10); and Se₈₀Te_20-xSn_x (x= 2, 4, and 10). The starting materials of (99.999%) purity were weighted according to their atomic percentages and sealed in evacuated silica tubes, under a pressure of about 10 …

Rehabilitation Of Concrete Structure Using Composite Materials, Ibtesam J.Saeed Al-Saifi

Theses

In the United Arab Emirates, most of the concrete structures including road, infrastructure and different types of buildings have been reported to be in need of rehabilitation. It is universally acknowledged that the environment of the countries in the Arabian Gulf is extremely severe and very aggressive to construction materials and operations. It is anticipated that the cost of rehabilitation of civil infrastructure will gradually increase over the next decade as a direct consequence of the increase in the number of structures reaching their expected service life.

Accordingly demand on rehabilitation methods will increase. In addition the severe climatic conditions …

Optimization Studies Of Thermal Bimorph Cantilevers, Electrostatic Torsion Actuators And Variable Capacitors, Wuyong Peng

Dissertations

In this dissertation, theoretical analyses and optimization studies are given for three kinds of MEMS devices: thermal bimorph cantilevers, electrostatic torsion actuators, and variable capacitors. Calculation, simulation, and experimental data are used to confirm the device behavior and demonstrate the application of the design approaches.

For thermal bimorph cantilevers, an analytical model is presented which allows theoretical analysis and quantitative optimization of the performance based on material properties and device dimensions. Bimorph cantilevers are divided into two categories for deflection optimization: either the total thickness is constant, or the cantilever has one constant and one variable layer thickness. The optimum …

Mechanisms Of Layer-Transfer Related To Silicon-On-Insulator Structures, Bo Chen

Dissertations

The objective of this dissertation was to study the mechanisms that affect an efficient hydrogenation process in silicon and to validate a hypothesis concerning the hydrogenation mechanism of pre-implanted silicon wafers under hydrogen-plasma processing. These studies are related to a general process. A trapping layer for hydrogen was introduced by ion beam implantation into the silicon wafer. Next, this wafer was hydrogenated using a hydrogen plasma. It was hypothesized that the trapping layer acts as a getterer for the hydrogen diffusing into the silicon wafer. It was found that a large amount of hydrogen could be absorbed in the trapping …

Boron And Phosphorous Implantation Into (100) Germanium : Modeling And Investigation Of Dopant Annealing Behavior, Yong Seok Suh

Dissertations

Germanium is increasingly being considered at this time for future silicon compatible optoelectronic and complementary metal oxide semiconductor (CMOS) device application. Germanium implantation will be a critical process for future device fabrication. However, critical properties like Pearson parameters and dopant activation temperatures are not well established. In this study, boron and phosphorus were implanted into (100) germanium with energies ranging from 20 to 320 keV and doses of 5 x 10¹³ to 5 x 10¹⁶ cm^-2. The behavior of the boron and phosphorus before and after annealing for 3 hours at 400, 600 or 800°C in …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: Third Quarterly Report 03/01/2004-05/31/2004, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the TRP proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Exchange Model For Oscillatory Interlayer Coupling And Induced Unidirectional Anisotropy In [Pt/Co]3/Nio/[Pt/Co]3 Multilayers, Mikhail Ye Zhuravlev, Evgeny Y. Tsymbal, Sitaram Jaswal

Materials Research Science and Engineering Center: Faculty Publications

In a recent Letter [1] Liu and Adenwalla found an interesting oscillatory behavior of the interlayer exchange coupling (IEC) through an insulating NiO (111) layer with a period of 2 monolayers (ML). They interpreted this phenomenon in terms of multiple reflections of electronic waves from a periodic atomic potential in the spirit of the model of Ref. [2]. However, this interpretation is not consistent with the tunneling mechanism used by the authors which would result in a modulated exponential decrease of the IEC but no periodic change in sign. In this Comment we show that the observed oscillatory IEC can …

Preparation, Characterization And Photoelectrochemical Activities Of Cu-Tio2/Ito Films, Dong Shu, Chun He, Han-Xia Zhang, Ya Xiong

Journal of Electrochemistry

Cu-TiO₂/ITO films were prepared by direct photo-reduction deposition of Cu²⁺ on TiO₂/ITO films. The nanocomposite films were characterized by UV-vis diffuse reflectance spectra (DRS), XRD spectra, Scanning Electron Microscope (SEM) technology, and photovoltage measurement. The feasibility of improving the photocatalytic activity of TiO₂ film by combining the modification of Cu nanoparticles with the application of anodic bias was investigated. The experimental results showed that the deposited Cu has an apparent enhancement effect with respect to suppressing the recombination between the photogenerated charge carriers and enhancing the photocatalytic oxidation of formic acid. The combination could …

Investigation Of Adsorption And Oxidation Behavior Of Isosafrole On A Smooth Pt, Xiao-Hong Zhang, Xiao-Jing Su, Qi-Ling Zhong, Lei Zhang, De-Sheng Mei, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

The electro-oxidation of isosafrole on a smooth platinum electrode was investigated in the non-aqueous solution. The CV curve shows two oxidation peaks and one reduction peak in the potential region between -0.5 V and 1.95 V. The relation between the oxidation and reduction peaks has been determined also by CV. The adsorption behavior of isosafrole on Pt was also investigated.

Stability And Electrochemical Performance Of Nio Cathode Modified By Zno Additive For Mcfc In Molten Carbonates, Bo Huang, Fei Li, Qing-Chun Yu, Gang Chen, Ke-Ao Hu

Journal of Electrochemistry

The ZnO/Ni composite cathode was fabricated by tape-casting method, which microstructures and phases were studied. The electrochemical behaviors of ZnO impregnated NiO cathodes were also evaluated in molten 62 mol%Li₂CO₃ + 38 mol%K₂CO₃eutectic at 650 ℃ by electrochemical impedance spectroscopy (EIS) as a function of ZnO content and immersion time. The ZnO impregnated nickel cathodes showed the similar porosity, pore size and morphology to the reference nickel cathode. The stability tests of ZnO impregnated NiO cathodes showed that the ZnO additive could dramatically reduce the solubility of NiO in a eutectic carbonate mixture …

Structures And Redox Activities Of Poly(M-Methoxyaniline), Yun-You He, Yi-Ting Xu, Li-Zong Dai, Jean-Yves Gal, Hui-Huang Wu

Journal of Electrochemistry

Poly(m-methoxyaniline), PmMAn, was prepared in the presence of HCl, p-toluene-sulfonic acid and perchloric acid. By using cyclic voltammetry, the effect of different acid dopant on electrochemical activities of PmMAn was studied. The results showed that perchloric acid is the best acid to prepare PmMAn with good electrochemical activities The FTIR spectra indicate that the acid radical anions have embedded into PmMAn molecularchain as counter-ion during synthetic process, and this great influences the redox activities of PmMAn. SEM and XRD measurements illustrate that PmMAn is characterized by its typical molecular crystalline being monoclinic.

Study On Reduction Process Of Electrolyic Manganese Dioxide In Situ By Ultraviolet-Visible Absorption Spectroscopy, Li-Cai Zhu, Zhong-Zhi Yuan, Wei-Shan Li

Journal of Electrochemistry

The concentrationsof soluble Mn(Ⅲ) species, during the reduction ofelectrolytic MnO₂ (EMD) in alkaline solution,have been monitored in situ by UV-visible spectroscopy. The concentration of Mn(Ⅲ) ion in solution changes with discharge time. The first electron discharge process of EMD can be described by three different steps: 1) the reduction of Mn⁴⁺ ions on the surface of EMD particles and the structural defect regions within the EMD, 2) the reduction of Mn⁴⁺ ions in ramsdellite, 3)the reduction of Mn⁴⁺ ions in pyrolusite. During the second electron discharge of EMD, the soluble Mn(Ⅲ) is reduced to Mn(Ⅱ) , …

Study Of Anti-Corrosion Property On Poly(An-Co-Oas)/Epoxy, Qing-Wu Wang, Geng-Chao Wang

Journal of Electrochemistry

Polyaniline, polyanisidine and their copolymer poly(An-co-oAs) were synthesized via the solution chemical oxidative polymerization of aniline and anisidine in an acidic aqueous medium, and their properties and structure were characterized. The electrochemical method were applied to evaluate the corrosion behavior of tined iron uncoated or coated by polyaniline, poly(An-o-oAs), polyanisidine and poly(An-co-oAs)/epoxy blend in acid or saline aqueous solution. The result showed that with the increase of anisidine content, the solubility of polymers is improved apparently but their oxidation extent decreases accordingly. It is also founded that polyaniline, poly(An-co-oAs) and polyanisidine all have good anti-corrosion properties, and their anti-corrosion capacity …

The Matching Study Of Electrodes In C/Ni(Oh)2 Hybrid Capacitor, Yue-Feng Su, Feng Wu

Journal of Electrochemistry

The energy storage mechanisms of electrochemical double-layer capacitor (EDLC) and C/Ni(OH)₂ hybrid capacitor had been studied. The results proved that,the difference between the capacity of EDLC and C/Ni(OH)₂ hybrid capacitor was detemined by the effectiveness usage of the activated carbon negative electrode, which is a criterion to estimate or design the theoretic capacity of the C/Ni(OH)₂ hybrid capacitor. The electrochemical availability of activated matter in Ni(OH)₂ electrode was introduced, and the quantity of the activated matter in Ni(OH)₂ electrode should be compatible with the capacity of carbon electrode. When the capacities of Ni(OH)₂ electrode …

Electrodeposition Of Copper Into Trenches Under Rotating Hydrodynamic Condition, Jian-Jun Sun, Bu-Gao Xie, Wen-Hui Yin, Guo-Nan Chen

Journal of Electrochemistry

Silicon chips patterned with treneches were fixed onto a rotating electrode. Copper was electrodeposited into the trenches under rotating hydrodynamic conditions The sizes of the trenches are 1 m in height and 0.35 m, 0.50 m and 0.70 m in width, respectively. The effects of rotating of the chip, the current density and the concentration of Cu²⁺ on the filling of thetrenches were studied. It is found that lower current density and moderate concentration of Cu²⁺ resulted in a void free filling of the trenches.

Two Kinds Of Polarons Observedin Polyaniline In Aqueous H2So4, Qin Zhou, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

Simultaneous electrochemistry electron spin resonance (ESR) conductance measurements were carried out on electropolymerized polyaniline and ESR spectra were obtained with high signal/noise ratio. Spectral simulation revealed that in the early stage of polymerization, there were two kinds of polarons. According to the potential dependence of the ESR line width and the corresponding conductivitychange of the polymer, the two polarons are thought to be in ordered and disordered domains, respectively. With increasing doping level, the two polarons underwent similar transfer from Curie spin to Pauli spin and both polarons were charge carriers in the conducting polymer. This deduction was further supported …

Studies Of Infrared Optical Properties Of Palladium Nanoparticles With Different Sizes And Dispersed States, Yan-Xia Jiang, Hong-Gang Liao, Wei Chen, Shi-Gang Sun

Journal of Electrochemistry

Pd nanoparticles with different sizes and dispersed states were prepared. Their infrared optical properties were studied with CO molecule probe. The infrared spectroscopic investigation revealed that Pd_n of 6.6 nm and Pd_n(cube)of 100～150nmexhibit normal IR absorption. The center of IR bands are around 1970 cm^-1 and 1910cm^-1. Pd_nis introduced into the surface of electrode, and is induced by interface electric fieldto form the aggregation of nanoparticles Pd_n(ag). The Pd_n(ag) has a different IR optical property from Pd_n. The direction of IR absorption band of Pd_{n …}

Electrochemical Lithium Insertion Of Nanosized Tio2, Ying Lan, Jian-Wen Liu, Xue-Ping Gao, Xing-Di Zhou, Jin-Qiu Qu, Feng Wu, De-Ying Song

Journal of Electrochemistry

The protonic titanate nanotubes with the diameter of 10～15 nm were synthesized via hydrothermal method in NaOH solution and the calcined nanotubes at 500 ℃ were transferred to anatase nanorods with the diameter of 12～20 nm due to dehydration.The electrochemical behavior of the anatase nanorods as lithium insertion materials was examined. The results showed that the nanorod electrode had the high initial discharge capacity of 232 mAh/g and second reversible capacity of 198 mAh/g. The capacity of nanorod electrode maintained 152mAh/g after 20 cycles.

Electrocatalytic And Lifetime Studies Of Commercial Catalystsin A Pemfc, Cheng Xuan, Yan-Yun Ma, Li Qi, Cheng Peng, Ling Chen, Jun Zhao, Ying Zhang, Qin-Bai Fan

Journal of Electrochemistry

A particularly designed H-type cell was used to simulate the operating condition of a hydrogen-air proton exchange membrane fuel cell (PEMFC). The electrocatalytic activity, morphology, structure and lifetime of commercially available catalysts, carbon support platinum (Pt/C) and unsupported platinum-ruthenium (Pt-Ru), were preliminary studied by carrying out electrochemical measurements and by SEM, XRD techniques. The catalysts were simultaneously tested in the H-cell under operation, and also separately tested in a conventional electrochemical cell for comparison. It was found that the characteristic peaks of hydrogen adsorption/desorption on cyclic voltammograms shifted considerably to a more positive direction for Pt/C, while a more negative …