Materials Science and Engineering Commons^™

Nucleation And Crystal Growth Of Pt Electrodeposition On Poly Crystal Au Microdisc Electrode, Zhi-Yong Tao, Pei-Fang Liu

Journal of Electrochemistry

Based on the Fleischmann's model of nucleation and crystal growth for electrodeposition combined with the Barradas-Bosco's adsorption-nucleation model for electrochemical phase formation, the chronoamperometry was well fitted for Pt deposition on polycrystalline Au micro disc electrodes (30 μm in diameter) in different H₂PtCl₆ concentrations at different over-potentials. The initial stage of Pt deposition in dilute H₂PtCl₆ could be interpreted by the model of H₂PtCl₆ adsorption combined with instantaneous nucleation and two-dimensional cylindrical growth. The rate constant of the two-dimensional growth increased linearly with overpotential. Then the deposit grew layer by layer …

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma, You-Qun Chu, Ying-Hong Zhu, Zhi-Hua Xu

Journal of Electrochemistry

The tungsten carbide (WC) electrode was constructed by using polyterafluoroethylene as binder. The electrochemical behavior of nitrobenzene on the WC electrode in acidic solution was investigated by cyclic voltammetry, linear scan method and chronoamperometry. Experimental results showed that WC electrode had good activity for the electrochemical reduction of nitrobenzene, and the electrode process was controlled by diffusion and electrochemical stepssimultaneously. The apparent active energy of the electrode process is 23.7kJ⋅mol^-1, while the active energy of the electrochemicalstep is 10.91kJ⋅mol^-1.

Preparation And Electrochemical Performance Of New Composite Seperators For Lithium-Ion Batteries, Hu Cheng, Hong-Yan Du, Yong Yang

Journal of Electrochemistry

New composite seperators for lithium ion batteries were prepared by coating PEO mixed with nanosize SiO₂ onto microporous polypropylene(PP) seperators. Highly conductive electrolytes were prepared by soaking them in an electrolyte solution. With these composite separators, the lithium ion cell consisting of Li anode and LiNi_0.8Co_0.2O₂ cathode were assembled. The high initial discharge capacity and good capacity retention were obtained through the cell.

Effects Of Barium On The Performance Of Secondary Alkaline Zinc Electrode, Yi Zheng, Jian-Ming Wang, Hua Chen, Hai-Bo Shao, Jian-Qing Zhang

Journal of Electrochemistry

The active material of secondary alkaline zinc electrode with barium additives was prepared by a chemical reaction method and characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The electrochemical performance of various pasted Zn electrodes was investigated by cyclic voltammetry, charge/discharge method and electrochemical impedance spectra (EIS) technology. The addition of barium can synthesize a compound barium zincate with the molecular structure of BaZn(OH)₄·xH₂O and improve the discharge performance. The EIS of the various Zn electrodes showed two time constants besides diffusion impedance, including a state variable representing the covering degree of discharge products …

Solid State Synthesis And Electrocatalysis Of Pt/Moo3 For The Oxidation Of Methanol, Qing Wang, Yi-Ming Zhou, Yang Shao, Yi-Gang Ji, Juan Xu, Ya-Wen Tang, Tian-Hong Lu, Tao Shen

Journal of Electrochemistry

The electrocatalyst, Pt/MoO₃ synthesized by solid state reaction, was used for the oxidation of methanol in direct methanol fuel cells. The X-Ray diffraction and cyclic voltammetry were employed to investigate the performance of the material. It was shown that the typical diffraction peaks for Pt appeared in XRD. And a good electrocatalysis for methanol oxidation was observed. The peak potential of the methanol oxidation appeared at ca. 0.63V(vs.SCE) and the peak current density for the oxidation was 78.1 mA⋅cm^-2.

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin

Journal of Electrochemistry

TiO₂(B) Nanobelts were synthesized by using the "Soft chemical"method. The products were characterized by means of transmission electron microscope(TEM), X-ray diffraction(XRD), Raman spectrum and energy dispersive spectrum(EDS). Galvanostatic charging and discharging tests showed that lithium-ion intercalation/deintercalation occurred reversibly in the TiO₂(B) nanobelts electrode, and a high capacity (265 mAh·g^-1) can be obtained. The results suggested that TiO₂(B) Nanobelts might be a promising negative electrode material of second Lithium battery.

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren, Zhen-Xing Liang, Xin-Sheng Zhao, Qin Xing, Gong-Quan Sun, Xue-Feng Yang

Journal of Electrochemistry

This paper describes the methanol permeability characterization of SPEEK membranes and their feasibility for DMFC application. The SPEEK membranes showed a significant lower methanol permeation than Nafion 115 determined from voltammetric methods. An increase in open circuit voltage was found in the performance of SPEEK membranes in DMFC. The power density of the cell using SPEEK membrane was considerably poorer than that of Nafion 115. If modified properly, the SPEEK membranes can be chosen for DMFC application based on this study.

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang

Journal of Electrochemistry

Tape cast method was applied to prepare green sheets of Ni/YSZ anode supported YSZ thin film. After isostatic pressure treatment and cosintering, the YSZ film on the Ni/YSZ anode was gas-tight dense, and 15~30 μm thick. The area of the composite film was over 100 cm². A Ce_0.8Sm_0.2O_1.9 (CSO) interlayer was sintered on to the YSZ electrolyte film to protect La_0.6Sr_0.4CoO₃ (LSCO) cathode from reaction with YSZ at high temperatures. The LSCO cathode layer was screen printed onto the CSO interlayer and sintered at 1200 ℃ for 3 …

Preparation Of Photo-Electrochemical Anticorrosion Tio2 Films By Anodization Method, Peng-Fei Wu, Mou-Cheng Li, Jia-Nian Shen, Mei-Qun Xiao, Dong Liu

Journal of Electrochemistry

Titanium oxide films have photo-electrochemical anticorrosion effect. We investigated the TiO₂ films prepared by anodization method to protect for 45# carbon steel in man-made seawater(3%NaCl). Various parameters, including voltages, electrolytes nature and concentration of electrolyte were examined. The polarization curves and of TiO₂ and coupling photo-current curve between TiO₂ film and 45#  carbon steel were measured.

First-Principles Study Of Adsorption Of Methanethiol On Co(0001), Ligen Wang, Evgeny Y. Tsymbal, Sitaram Jaswal

Materials Research Science and Engineering Center: Faculty Publications

Investigation of the resident site and the adsorption phase structure of thiolates is of fundamental importance for understanding the formation of self-assembled organic monolayers on metal substrate surfaces. In the present study, we have investigated adsorption of methanethiol, CH₃SH, on the ferromagnetic Co (0001) surface using density functional theory calculations.We find that the dissociative adsorption of CH₃SH forming an adsorbed methylthiolate (CH₃S) and an adsorbed H atom is energetically favorable, and that the CH₃S molecule adsorbed at the threefold fcc and hcp hollow sites is most stable. The adsorption energy at the …

Mixed Ion-Polaron Transport In Na2o-Pbo-Fe2o3-P2o5 Glasses, A. Moguš-Milanković, A. Šantić, Signo Tadeu Dos Reis, K. Furić, D. E. Day

Materials Science and Engineering Faculty Research & Creative Works

The electrical and dielectric properties of the xNa₂O · (100 - x) · [28.3PbO · 28.7Fe₂O₃ · 43.0P₂O₅] (0 ≤ x ≤ 30) glasses were measured by impedance spectroscopy in the frequency range from 0.01 Hz to 3 MHz and the temperature range from 303 to 473 K. the conductivity for glasses containing ≤15 mol% Na₂O is predominantly electronic and is controlled by electron hopping between Fe(II) and Fe(III) ions. in these glasses the sodium ions have such a low mobility, caused by ion-polaron interaction, that they make no …

Study Of Ceramic Slurries For Investment Casting With Ice Patterns, Qingbin Liu, Ming-Chuan Leu, Harish Jose, Von Richards

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Ice patterns generated by rapid freeze prototyping or a molding process can be used to make ceramic investment molds for metal castings. Due to the use of ice, the ceramic slurries must be poured around the pattern and cured at sub-freezing temperatures. Success of this process depends greatly on the mold strength after the gelation of the slurries. This paper describes the experimental results of the mold strength after the gelation of the slurries under different compositions. The parameters considered include mixing time, alumino-silicate vs. fused silica ratio, volume of binder, and volume of catalyst. The strength of the gelled …

Wavelenght-Dispersive X-Ray Flourescence Accuration, H. Widyatmoko

Makara Journal of Technology

Wavelenght–Dispersive X-Ray Flourescence Accuration. X-Fuorescence spectrometry is a method, which is increasingly applied in the geochemical analysis. X-Fuorescence spectrometry is classified under two categories – WDXRF (wavelenght – dispersive X-ray fluorescence spectrometer) and EDXRF (energy-dispersive X – ray fluorescence spectrometer). WDXRF can be configured as a sequential spectrometer , a simultaneous spectrometer or a hibrid instrument, which combines the advantages of the simultaneous and sequential spectrometers into one instrument. Each instrument is different in some characteristics, and each has applications for which it is specifically suited. In this investigation sequential spectrometer PW 1450 was used to analyze the major, minor …

Secondary Flow Experimental Study For Axial Compressor Cascade Strong Stagger With And Without Tip- Clearance: Static Pressure Distribution On Blade Surface, Syamsuri Syamsuri

Makara Journal of Technology

Secondary Flow Experimental Study for Axial Compressor Cascade Strong Stagger With and Without Tip- Clearance: Static Pressure Distribution on Blade Surface. The performance of blade cascade is influenced by the growth and boundary layer’s separation along blade surface and endwall (casing and hub). The secondary flow which happens near hub and casing compressors is three dimentional flow separation phenomenon comes from interaction blade boundary layer with casing and hub boundary layers in the compressor. The secondary flow causes secondary losses, blockage effect, and turning angle (deflection) distribution along blade span. The result of the research shows that the increase of …

Effect Of Photoperiodicity On Co2 Fixation By Chlorella Vulgaris Buitenzorg In Bubble Column Photobioreactor For Food Supplement Production, Anondho Wijanarko, Dianursanti Dianursanti, Arief Budi Witarto, Roekmijati Widaningroem Soemantojo

Makara Journal of Technology

To reduce the level of CO2 content in air, effort on converting CO2 to useful products is required. One of the alternatives includes CO2 fixation to produce biomass using Chlorella vulgaris Buitenzorg. Chlorella vulgaris Buitenzorg is applied for production of food supplement. Chlorella vulgaris Buitenzorg is also easy to handle due to its superior adaptation. Currently, Chlorella vulgaris Buitenzorg has been analyzed by some experts for its cellular composition, its ability to produce high quality biomass and the content of essential nutrition. A series of experiments was conducted by culturing Chlorella vulgaris Buitenzorg using Beneck medium in bubbling column photobioreactor. …

Synthesize Of Emulsion Polymer Latex For Sub-Grade Cbr Improvement In The Road Construction, Keba Moto, V. Julian, Syamsudin Syamsudin, T. A. Wiradi, S. R. Wijaya

Makara Journal of Technology

Synthesize of emulsion polymer latex for sub-grade CBR improvement in the road construction. Latex polymer for California Bearing Ratio (CBR) enhancement in sub-grade soil of road building has been prepared by emulsion polymerizations technique. The prepared polymer then characterize by Fourier Transform Infrared (FTIR). For application purpose, CBR test was done to the compacted polymer added-soil. The CBR test is done also for both soaked and unsoaked samples. It is found that our latex polymer is better then other imported latex polymer. For the latex polymer, which is design to have Temperatur glass (Tg) around 9.8-19.6o, indicating the formation of …

Experimental Investigation Of Time Dependent Behavior Of Welded Topopah Spring Tuff, Lumin Ma

Publications (YM)

Four types of laboratory tests have been performed. Specimens were attained from four lithophysal zones of the welded Topopah Spring Tuff unit at Yucca Mountain, Nevada: upper lithophysal, middle nonlithophysal, lower lithophysal and lower nonlithophysal zones. Two types of tests are conducted to study time-dependent behavior: constant strain rate and creep tests. Sixty five specimens from the middle nonlithophysal zone were tested at six strain rates: 10 , 10 , 10 , 10 , 10 , and 10 . Test durations range from 2 seconds to 7 days. Fourteen specimens from middle nonlithophysal, lower lithophysal and lower nonlithophysal zones are …

46th Rocky Mountain Conference On Analytical Chemistry

Rocky Mountain Conference on Magnetic Resonance

Final program, abstracts, and information about the 46th annual meeting of the Rocky Mountain Conference on Analytical Chemistry, co-endorsed by the Colorado Section of the American Chemical Society and the Rocky Mountain Section of the Society for Applied Spectroscopy. Held in Denver, Colorado, August 1-5, 2004.

Embrittlement And Localized Corrosion In Alloy Ht-9, Sudheer Sama

UNLV Theses, Dissertations, Professional Papers, and Capstones

This investigation is focused on the evaluation of stress corrosion cracking (SCC), hydrogen embrittlement (HE) and localized corrosion susceptibility of Alloy HT -9 in neutral and acidic solutions at 30, 60 and 90°C. Constant-load and slow-strain-rate (SSR) testing techniques were used to evaluate the SCC and HE behavior of this alloy by using smooth and notched tensile specimens. Hydrogen effect on the cracking behavior was evaluated by applying cathodic (negative) potential to the test specimens. Localized corrosion susceptibility was evaluated by cyclic potentiodynamic polarization technique. The results of constant load SCC testing showed a threshold stress at 80% of the …

Environment-Induced Degradations In A Target Structural Material For Transmutation Applications, Ramprashad Prabhakaran

UNLV Theses, Dissertations, Professional Papers, and Capstones

This investigation is focused on the evaluation of stress corrosion cracking (SCC) and localized corrosion behavior of Type 422 stainless steel in aqueous environments at ambient and elevated temperature. The results of constant load SCC testing using smooth specimens showed no failure in the neutral solution but a threshold stress of 97 ksi was observed in the 90°C acidic environment. SCC testing by the slow-strain-rate test method indicate that the time-to-failure, true failure stress and ductility parameters were gradually reduced with increasing temperature, showing more pronounced effect in the acidic solution. The application of a controlled cathodic potential showed further …

Field-Controlled Domain-Wall Resistance In Magnetic Nanojunctions, John D. Burton, Arti Kashyap, Mikhail Ye. Zhuravlev, Ralph Skomski, Evgeny Y. Tsymbal, Sitaram Jaswal, O.N. Mryasov, R.W. Chantrell

Materials Research Science and Engineering Center: Faculty Publications

The electrical resistance of a constrained domain wall in a nanojunction is investigated using micromagnetic modeling and ballistic conductance calculations. The nanojunction represents two ferromagnetic electrodes connected by a ferromagnetic wire of 10 nm in length and of a few nanometers in cross section. We find that the anisotropy of the electrodes favors a localization of the domain wall within the constriction (wire) revealing a positive domain-wall resistance. An applied magnetic field moves the domain wall toward one of the electrodes and reduces its width. This compression of the domain wall leads to a sizeable enhancement of the domain-wall resistance.

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials: Annual Progress Report (May 2003 – May 2004), Ajit K. Roy

Transmutation Sciences Materials (TRP)

As indicated in the original proposal, the primary objective of this task was to evaluate the effect of hydrogen on environment-assisted cracking of candidate target structural materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization were martensitic stainless steels including Alloy EP 823, HT-9, and Type 422 stainless steel. The susceptibility to stress corrosion cracking (SCC) of these materials were evaluated in neutral and acidic aqueous environments using smooth and notched tensile specimens under constant-load (CL) and slow-strain-rate (SSR) conditions. Further, the …

Fabrication, Characterization, And Modeling Of Organic Capacitors, Schottky Diodes, And Field Effect Transistors, Mo Zhu

Doctoral Dissertations

The objectives of this project are to fabricate, characterize, and model organic microelectronic devices by traditional lithography techniques and Technology Computer Aided Design (TCAD).

Organic microelectronics is becoming a promising field due to its number of advantages in low-cost fabrication for large area substrates. There have been growing studies in organic electronics and optoelectronics. In this project, several organic microelectronic devices are studied with the aid of experimentation and numerical modeling.

Organic metal-insulator-metal (MIM) and metal-insulator-semiconductor (MIS) capacitors consisting of insulating polymer poly(4-vinylphenol) (PVP) have been fabricated by spin-coating, photo lithography, and reactive ion etching techniques. Based on the fabricated …

The Effect Of Transition Metal Additions On The Microstructure And Properties Of Nanocomposite Pr–Fe–B Permanent Magnets, Jeffrey E. Shield, Yi Liu, R. Marr, Z. Chen, Baomin Ma

Materials Research Science and Engineering Center: Faculty Publications

Permanent magnets with the general composition Pr₉ (Fe_0.95Co_0.05)_85.5M_0.5B₅, where M denotes a transition metal, have been produced by melt spinning. The effect on the microstructure and magnetic properties of eight different alloying elements has been examined. The grain size and distribution have been correlated to the maximum energy product obtained. The grain size of the Pr₉ (Fe_0.95Co_0.05) _85.5B₅ control alloy was determined to be 17.5 nm, and it was found that the grain size was not significantly reduced compared to the control …

Domain-Wall Pinning At Inhomogenities Of Arbitrary Cross-Sectional Geometry, Ralph Skomski, Jian Zhou, Arti Kashyap, David J. Sellmyer

Materials Research Science and Engineering Center: Faculty Publications

Abstract—The coercivity of cellular Sm-Co based permanent magnets is investigated by model calculations. The grain boundaries responsible for the pinning coercivity are modeled as planar inhomogenities with arbitrary cross-sectional geometry. The calculation yields a physically transparent integral equation for the pinning energy, whose derivative is the pinning force. The theory rationalizes experimental data on a semiquantitative level, but without adjustable parameters, and bridges the gap between smooth concentration gradients and abrupt interfaces. Explicit results are obtained for sinoidal profiles, for very thin grain boundaries, and for profiles intermediate between attractive and repulsive pinning. The corrections predicted by the present model …

Magnetization Reversal And Giant Coercivity In Sm-Co/Cu-Ti Particulate Films, Jian Zhou, Arti Kashyap, Yi Liu, Ralph Skomski, David J. Sellmyer

Materials Research Science and Engineering Center: Faculty Publications

Highly coercive granular SmCo/CuTi films were produced by thermal processing of sputtered SmCo₅ (CuTi) multilayers and investigated experimentally and theoretically. Electron microscopy shows that the processed films consist of spherical grains that have diameters of 5–10 nm and are embedded in a matrix. Both the grains and the matrix phase exhibit the CaCu₅ structure, but the matrix is probably Cu-rich. The films have high coercivities of up to 50.4 kOe at 300 K. Analytical calculations and micromagnetic simulations yield a transition from a nucleation-type weak-interaction regime to a discrete-pinning-type strong-interaction regime. The transition occurs at packing fractions similar …

L10 Ordered Fept:C Composite Films With (001) Texture, M. L. Yan, Renat F. Sabiryanov, Yinfan Xu, Xingzhong Li, David J. Sellmyer

Materials Research Science and Engineering Center: Faculty Publications

Highly textured (001) FePt:C nanocomposite thin films, deposited directly on thermally oxidized Si wafers, are obtained by multilayer deposition plus subsequent thermal annealing. Nanostructures, crystalline orientations, interactions, and magnetic properties are investigated by transmission electron microscopy (TEM), X-ray diffraction (XRD), magnetic force microscopy, and magnetic measurements. The formation of the ordered L1₀ phase is confirmed by XRD, and only visible (00 ) peaks indicate a high degree of the (001) texture. TEM observation reveals that FePt grains are embedded in the C matrix and appear to be well isolated.

Nanostructure And Magnetic Properties Of Fept :C Cluster Films, Yinfan Xu, M. L. Yan, David J. Sellmyer

Materials Research Science and Engineering Center: Faculty Publications

Magnetic properties and nanostructure of FePt : C cluster-deposited films with C volume fraction of 7%, 14%, 33%, and 45% have been studied. As-deposited FePt : C films were prepared by a multilayer method in which FePt layers were deposited from a cluster source employing a gas-aggregation technique and C layers from a normal sputtering gun. In the as-deposited films, FePt clusters with fcc structure are embedded in the C matrix. The high anisotropy FePt L1₀ cluster structure was realized in the films via post-deposition annealing and the nanostructure of the films was observed by high-resolution transmission electron microscope …

Magnetization Processes In Melt-Spun Sm-Co-Based Alloys With The Tbcu7-Type Structure, A. Hsiaoa, S. Aich, L. H. Lewis, Jeffrey E. Shield

Materials Research Science and Engineering Center: Faculty Publications

The initial magnetization processes in melt-spun Sm-Co alloys with remanent ratios above 0.7 have been studied. Alloys of (Sm_(1/(6+x) Co _(5+x)/(6+x) ) ₉₄Nb₃C₃ (x = 067, 1.7, 2.3 and 3) alloys modified with Nb and C were melt spun at wheel speeds of 20 and 40 m/s, and the compositions span the range between the Sm₂Co₁₇ and SmCo_{5 stoichiometries. Structurally, all alloys formed in the TbCu7-type structure, although a small amount of Sm2Co7 was observed in Sm-rich samples, and a small amount of fcc Co formed …}

Artificial Neural Network Modeling Of Rf Mems Resonators, Yongjae Lee, Yonghwa Park, Feng Niu, Bonnie Bachman, K. C. Gupta, Dejan Filipovic

Economics Faculty Research & Creative Works

In this article, a novel and efficient approach for modeling radio‐frequency microelectromechanical system (RF MEMS) resonators by using artificial neural network (ANN) modeling is presented. In the proposed methodology, the relationship between physical‐input parameters and corresponding electrical‐output parameters is obtained by combined circuit/full‐wave/ANN modeling. More specifically, in order to predict the electrical responses from a resonator, an analytical representation of the electrical equivalent‐network model (EENM) is developed from the well‐known electromechanical analogs. Then, the reduced‐order, nonlinear, dynamic macromodels from 3D finite‐element method (FEM) simulations are generated to provide training, validating, and testing datasets for the ANN model. The developed ANN …