Materials Science and Engineering Commons^™

Magnetic Properties Of Nd–Fe–B Permanent Magnets Under Thermal Experimentation, Géraldine Houis

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Neodymium-Iron-Boron (Nd-Fe-B) magnets were developed in the 1980s, and since then, they have appeared as a common component in many fields. From the industry to consumers or defense applications, from turbines, computers, cellphones to most audio systems, Nd-Fe-B magnets are present everywhere. But when Nd-Fe-B magnets are applied to the motors of electric vehicles and wind-turbine generators, their temperature rises, therefore Nd-Fe-B-Dy magnets are used. However, while the use of these magnets is common at low temperatures, their properties decrease dramatically with the increase of temperature. In this paper, the Nd-Fe-B-based samples used were prepared by using arc melting, melt …

Extending Mission Duration Of Uas Multicopters: Multi-Disciplinary Approach, Marc Lussier

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Multicopters are important tools in industry, the military, and research but suffer from short flight times and mission durations. In this thesis, we discuss three different ways to increase flight times and therefore increase the viability of using multicopters in a variety of missions. Alternate fuel sources such as hydrogen fuel and solar cells are starting to be used on multicopters, in our research we simulate modern fuel cells and show how well they currently work as the power source for multicopters and how close they are to becoming useful in Unmanned Aircraft System (UAS) technology. Increasing the efficiency in …

The Application Of Gray-Scale Level-Set Method In Segmentation Of Concrete Deck Delamination Using Infrared Images, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Conventional nondestructive delamination detection of concrete pavements through thermography is often based on temperature contrasts between delaminated and sound areas. Non-uniform backgrounds caused by the environmental conditions are often challenging for contrast-based methods to robustly differentiate the delaminated areas from the sound areas. Instead of focusing on the temperature contrast, this study proposes a temperature gradient-based level set method (LSM) to detect boundaries for delamination segmentations. A modified edge indicator function is developed to represent the normalized temperature gradient of a thermal image. The experimental study was conducted to evaluate its applicability and stability for boundary detection in terms of …

Double-Sided Corrugated Composite Tube And Axle Protective Mechanism For Railway Vehicles, Hozhabr Mozafari

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Structural elements in transportation vehicles are exposed to different types of dynamic loadings and impact scenarios. Protecting passengers against injury and providing mechanisms to avoid impact induced damages to the critical components are the two hot topics in crashworthiness engineering. The presented research work includes two parts. The first part is about designing a novel double-sided composite corrugated tube that can be implemented in front chassis rail of ground vehicles to improve their crashworthiness against collision and car accidents. To maximize the controllable energy absorption of corrugation troughs as observed in the single sided corrugated (SSC) tube, we proposed and …

Smart Additive Manufacturing: In-Process Sensing And Data Analytics For Online Defect Detection In Metal Additive Manufacturing Processes, Mohammad Montazeri

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The goal of this dissertation is to detect the incipient flaws in metal parts made using additive manufacturing processes (3D printing). The key idea is to embed sensors inside a 3D printing machine and conclude whether there are defects in the part as it is being built by analyzing the sensor data using artificial intelligence (machine learning). This is an important area of research, because, despite their revolutionary potential, additive manufacturing processes are yet to find wider acceptance in safety-critical industries, such as aerospace and biomedical, given their propensity to form defects. The presence of defects, such as porosity, can …

Electrically Conductive Concrete Mix For Electromagnetic (Em) Ground Plane, Christopher Tuan, Lim Nguyen

Department of Civil and Environmental Engineering: Faculty Publications

Conductive concrete mixtures are described that are configured to reflect, for instance, EM waves propagating from an EM pulser onto the conductive concrete mixture forming a ground plane, rather than absorb or dissipate the electromagnetic energy. The conductive concrete mixtures include cement, aggregate, water, metallic conductive material, and conductive carbon particles.

Bridge Deck Delamination Segmentation Based On Aerial Thermography Through Regularized Grayscale Morphological Reconstruction And Gradient Statistics, Chongsheng Cheng, Zhexiong Shang, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Environmental and surface texture-induced temperature variation across the bridge deck is a major source of errors in delamination detection through thermography. This type of external noise poises a significant challenge for conventional quantitative methods such as global thresholding and k-means clustering. An iterative top-down approach is proposed for delamination segmentation based on grayscale morphological reconstruction. A weight-decay function was used to regularize the reconstruction for regional maxima extraction. The mean and coefficient of variation of temperature gradient estimated from delamination boundaries were used for discrimination. The proposed approach was tested on a lab experiment and an in-service bridge deck. The …

Deformation Mechanisms In Mg–Al Nanocomposite, Soodabeh Azadehranjbar, Jian Wang, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Magnesium is the lightest engineering metal. Replacing steel with Mg based materials in automotive applications would lead to more than 40% weight reduction which significantly boost fuel efficiency. However, conventional Mg alloys typically suffer from low strength and poor deformability due to very few slip systems and easy twinning. Alloying Mg with other materials and microstructural engineering are promising approaches to increase ductility and strength of Mg According to Wang et al. interfaces with low energy and high coherency may effectively constrict the nucleation of twins in Mg In this work, the microstructure of Mg nano layers and nano rods …

Thermographic Laplacian-Pyramid Filtering To Enhance Delamination Detection In Concrete Structure, Chongsheng Cheng, Ri Na, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Despite decades of efforts using thermography to detect delamination in concrete decks, challenges still exist in removing environmental noise from thermal images. The performance of conventional temperature-contrast approaches can be significantly limited by environment-induced non-uniform temperature distribution across imaging spaces. Time-series based methodologies were found robust to spatial temperature non-uniformity but requires extended period to collect data. A new empirical image filtering method is introduced in this paper to enhance the delamination detection using blob detection method that originated from computer vison. The proposed method employs a Laplacian of Gaussian filter to achieve multi-scale detection of abnormal thermal patterns by …

Proximitized Materials, Igor Žutić, Alex Matos-Abiague, Benedikt Scharf, Hanan Dery, Kirill Belashchenko

Kirill Belashchenko Publications

Advances in scaling down heterostructures and having an improved interface quality together with atomically thin two-dimensional materials suggest a novel approach to systematically design materials. A given material can be transformed through proximity effects whereby it acquires properties of its neighbors, for example, becoming superconducting, magnetic, topologically nontrivial, or with an enhanced spin–orbit coupling. Such proximity effects not only complement the conventional methods of designing materials by doping or functionalization but also can overcome their various limitations. In proximitized materials, it is possible to realize properties that are not present in any constituent region of the considered heterostructure. While the …

Femtosecond Photon-Mediated Plasma Enhances Photosynthesis Of Plasmonic Nanostructures And Their Sers Applications, Peng Ran, Lan Jiang, Xin Li, Bo Li, Pei Zuo, Yongfeng Lu

Department of Electrical and Computer Engineering: Faculty Publications

Laser ablation in liquid has proven to be a universal and green method to synthesize nanocrystals and fabricate functional nanostructures. This study demonstrates the superiority of femtosecond laser-mediated plasma in enhancing photoredox of metal cations for controllable fabrication of plasmonic nanostructures in liquid. Through employing upstream high energetic plasma during laser-induced microexplosions, single/three-electron photoreduction of metallic cations can readily occur without chemical reductants or capping agents. Experimental evidences demonstrate that this process exhibits higher photon utilization efficiency in yield of colloidal metal nanoparticles than direct irradiation of metallic precursors. Photogenerated hydrated electrons derived from strong ionization of silicon and water …

Drop Generation Using Cross-Flow In Rigid Body Rotation, Haipeng Zhang

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Inspired by crossflow membrane droplet generation and microfluidic droplet generation, I propose an easy method to generate monodisperse drops using cross-flow caused by rigid body rotation. In this approach, a dispersed phase (DP) liquid was injected through a stationary vertical needle into an immiscible continuous phase (CP) liquid which was in rigid body rotation. A DP drop growing at the end of the needle experienced fluid dynamic forces from the horizontal CP flow, and it was detached from the needle when it had grown to a certain size. This study investigated the relationship between the resultant size of drops and …

Magnetoelectric Memory Cells With Domain-Wall-Mediated Switching, Kirill Belashchenko, Oleg Tchernyshyov, Alexey Kovalev, Dmitri Nikonov

Kirill Belashchenko Publications

A magnetoelectric memory cell with domain - wall - mediated switching is implemented using a split gate architecture . The split gate architecture allows a domain wall to be trapped within a magnetoelectric antiferromagnetic ( MEAF ) active layer . An extension of this architecture applies to multiple gate linear arrays that can offer advantages in memory density , programmability , and logic functionality . Applying a small anisotropic in - plane shear strain to the MEAF can block domain wall precession to improve reliability and speed of switching

Study Of The Femtosecond Laser Processed Surfaces, Imprinting, And Casting For Changing The Wettability Of Surfaces, Yingxiao Song

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Femtosecond Laser Surface Processing (FLSP) is a technology to fabricate micro/nano surface structures. These patterned surface structures show great importance in many applications, especially in controlling the wettability of the surface. Imprinting is a typical method for manufacturing large volumes of surfaces. This study combines two processes (FLSP and stamping) together to produce a surface structure similar to the original FLSP surface. In the first step, micro/nano structured surface mounds were fabricated by femtosecond laser processing. Then, these FLSP surfaces served as molds for subsequent imprinting to replicated the “negative” surface on a blank material. Surface morphology and peak-to-valley roughness …

Tunable Plasmonic Resonances In Highly Porous Nano-Bamboo Si-Au Superlattice-Type Thin Films, Ufuk Kılıç, Alyssa Mock, René Feder, Derek Sekora, Matthew J. Hilfiker, Rafal Korlacki, Eva Schubert, Christos Argyropoulos, Mathias Schubert

Department of Electrical and Computer Engineering: Faculty Publications

We report on fabrication of spatially-coherent columnar plasmonic nanostructure superlattice-type thin films with high porosity and strong optical anisotropy using glancing angle deposition. Subsequent and repeated depositions of silicon and gold lead to nanometer-dimension subcolumns with controlled lengths. The superlattice-type columns resemble bamboo structures where smaller column sections of gold form junctions sandwiched between larger silicon column sections (“nano-bamboo”). We perform generalized spectroscopic ellipsometry measurements and finite element method computations to elucidate the strongly anisotropic optical properties of the highly-porous nano-bamboo structures. The occurrence of a strongly localized plasmonic mode with displacement pattern reminiscent of a dark quadrupole mode is …

Interface Structure And Deformation Mechanisms Of Mg/Nb Multilayers, Xinyan Xie

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Magnesium (Mg) and its alloys, as the lightest structural materials, are very attractive for a range of weight sensitive applications, such as aircraft engine, transportation industry and so on. However, their further applications are limited due to the weak properties, such as the low strength and poor ductility. In recent years, advanced techniques aiming at the modification of the microstructures, have been developed to promote the properties of Mg and its alloys, such as modifying the texture, refining the grain size, forming the intermetallic phase, and introducing the interfaces or stacking faults into the systems. Constructing Mg/Nb multilayers, which introduces …

Critical-Point Model Dielectric Function Analysis Of Wo3 Thin Films Deposited By Atomic Layer Deposition Techniques, Ufuk Kılıç, Derek Sekora, Alyssa Mock, Rafał Korlacki, Elena M. Echeverría, Natale J. Ianno, Eva Schubert, Mathias Schubert

Department of Electrical and Computer Engineering: Faculty Publications

WO₃ thin films were grown by atomic layer deposition and spectroscopic ellipsometry data gathered in the photon energy range of 0.72-8.5 eV and from multiple samples was utilized to determine the frequency dependent complex-valued isotropic dielectric function for WO₃. We employ a critical-point model dielectric function analysis and determine a parameterized set of oscillators and compare the observed critical-point contributions with the vertical transition energy distribution found within the band structure of WO₃ calculated by density functional theory. We investigate surface roughness with atomic force microscopy and compare to ellipsometric determined effective roughness layer thickness.

Peridynamic Modeling Of Dynamic Fracture In Bio-Inspired Structures For High Velocity Impacts, Sneha Akula

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Bio-inspired damage resistant models have distinct patterns like brick-mortar, Voronoi, helicoidal etc., which show exceptional damage mitigation against high-velocity impacts. These unique patterns increase damage resistance (in some cases up to 3000 times more than the constituent materials) by effectively dispersing the stress waves produced by the impact. Ability to mimic these structures on a larger scale can be ground-breaking and could be used in numerous applications. Advancements in 3D printing have now made possible fabrication of these patterns with ease and at a low cost. Research on dynamic fracture in bio-inspired structures is very limited but it is …

Nanostructural Origin Of Semiconductivity And Large Magnetoresistance In Epitaxial Nico2O4/Al2O3 Thin Films, Congmian Zhen, Xiaozhe Zhang, Wengang Wei, Wenzhe Guo, Ankit Pant, Xiaoshan Xu, Jian Shen, Li Ma, Denglu Hou

Xiaoshan Xu Papers

Despite low resistivity (~1 mΩ cm), metallic electrical transport has not been commonly observed in inverse spinel NiCo₂O₄, except in certain epitaxial thin films. Previous studies have stressed the effect of valence mixing and the degree of spinel inversion on the electrical conduction of NiCo₂O₄ films. In this work, we studied the effect of nanostructural disorder by comparing the NiCo₂O₄ epitaxial films grown on MgAl₂O₄ (1 1 1) and on Al₂O₃ (0 0 1) substrates. Although the optimal growth conditions are similar for the …

Saw Assisted Domain Wall Motion In Co/Pt Multilayers, Westin Edrington, Uday Singh, Maya Abo Dominguez, James Rehwaldt Alexander, Rabindra Nepal, Shireen Adenwalla

Shireen Adenwalla Papers

The motion of domain walls in thin ferromagnetic films is of both fundamental and technological interest. In particular, the ability to use drivers other than magnetic fields to control the positions of domain walls could be exciting for memory applications. Here, we show that high frequency dynamic strain produced by surface acoustic waves is an efficient driver of magnetic domain walls in ferromagnetic films with perpendicular anisotropy. A standing surface acoustic wave of resonant frequency 96.6MHz increases the domain wall velocities in thin films of [Co/Pt]n by an order of magnitude compared to magnetic fields alone. This effect is highly …

Generalized Ellipsometry On Complex Nanostructures And Low-Symmetry Materials, Alyssa Mock

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, complex anisotropic materials are investigated and characterized by generalized ellipsometry. In recent years, anisotropic materials have gained considerable interest for novel applications in electronic and optoelectronic devices, mostly due to unique properties that originate from reduced crystal symmetry. Examples include white solid-state lighting devices which have become ubiquitous just recently, and the emergence of high-power, high-voltage electronic transistors and switches in all-electric vehicles. The incorporation of single crystalline material with low crystal symmetry into novel device structures requires reconsideration of existing optical characterization approaches. Here, the generalized ellipsometry concept is extended to include applications for materials with …

Synthesis Of Graphene And Graphene-Based Composite Membrane, Yuanjun Fan

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Vibration membrane equipped for earphone requires high performance in both mechanical properties and electronic properties. With extraordinary properties on both, graphene and graphene-based composite materials appear as a promising candidate for this application. Chemical vapor deposition (CVD) is believed to be the most convenient way to synthesize a large area (on scale of square centimeters) as well as a homogeneous thickness for the membrane. The thesis focuses on applying control variable experiment method to analyze different effects on mechanical property of the two CVD setting parameters: cooling rate, and hydrocarbon precursor. For isolating the specimens efficiently, a modified electrochemical method …

Viscoelastic Analysis And Fatigue Characterization Of Bituminous Materials In Two Length Scales Under The Influence Of Aging, Santosh Reddy Kommidi

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Fatigue cracking in asphalt concrete (AC) is of immense importance to pavement design and analysis because it is one of the most important forms of distress that can lead to structural failure in pavement. Once started, these types of cracks can be combined with other environmental factors leading to detrimental effects such as faster rates of pavement deterioration and shortened pavement life and functionality.

Currently AASHTO TP101, also known as linear amplitude sweep (LAS) specification, is being widely used to evaluate the ability of an asphalt binder to resist fatigue. The LAS method, although mechanistic in its approach, has certain …

Electrical Characterization Of Irradiated Semiconducting Amorphous Hydrogenated Boron Carbide, George Glen Peterson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Semiconducting amorphous partially dehydrogenated boron carbide has been explored as a neutron voltaic for operation in radiation harsh environments, such as on deep space satellites/probes. A neutron voltaic device could also be used as a solid state neutron radiation detector to provide immediate alerts for radiation workers/students, as opposed to the passive dosimetry badges utilized today. Understanding how the irradiation environment effects the electrical properties of semiconducting amorphous partially dehydrogenated boron carbide is important to predicting the stability of these devices in operation. p-n heterojunction diodes were formed from the synthesis of semiconducting amorphous partially dehydrogenated boron carbide on silicon …

Molecular Dynamics Modeling And Simulation Of Bitumen Chemical Aging, Farshad Fallah

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Chemical aging of asphalt binder leads to significant changes in its mechanical and rheological properties, resulting in poor pavement behavior and distress. Various laboratory methods have been used to simulate asphalt aging during the service life of the pavement. However, controversy exists regarding the capability of these methods to predict field aging, as various factors interact with the pavement during service and the mechanism behind aging is not fully understood. The two main outcomes of chemical aging are oxidation of asphalt molecules, and change in asphalt SARA (saturate, aromatic, resin, and asphaltene) fractions. Reaction of oxygen with asphalt components forms …

Elastic Properties Of Superconductors And Materials With Weakly Correlated Spins, Christian Binek

Christian Binek Publications

It is shown that in the ergodic regime, the temperature dependence of Young’s modulus is solely determined by the magnetic properties of a material. For the large class of materials with paramagnetic or diamagnetic response, simple functional forms of the temperature derivative of Young’s modulus are derived and compared with experimental data and empirical results. Superconducting materials in the Meissner phase are ideal diamagnets. As such, they display remarkable elastic properties. Constant diamagnetic susceptibility gives rise to a temperature independent elastic modulus for ceramic and single crystalline superconductors alike. The thermodynamic approach established in this report, paves the way to …

The Magnetic, Electrical And Structural Properties Of Copper-Permalloy Alloys, Makram A. Qader, A. Vishina, Lei Yu, Cougar Garcia, Rakesh K. Singh, Nicholas D. Rizzo, Mengchu Huang, Ralph Chamberlin, Kirill Belashchenko, Mark Van Schilfgaarde, N. Newman

Kirill Belashchenko Publications

Copper-permalloy [Cu_1–x(Ni₈₀Fe₂₀)_x] alloy films were deposited by co-sputtering and their chemical, structural, magnetic, and electrical properties were characterized. These films are found to have favorable weak ferromagnetic properties for low temperature magnetoelectronic applications. Our results show that by varying the composition, the saturation magnetization (M_s) can be tuned from 700 emu/cm³ to 0 and the Curie temperature (T_c), can be adjusted from 900 K to 0 K. The M_s and T_c are found to scale linearly between x = 25% and 100%. Electronic structure calculations …

Peridynamic Models For Fatigue And Fracture In Isotropic And In Polycrystalline Materials, Guanfeng Zhang

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

To improve design and reliability, extensive efforts has been devoted to understanding damage and failure of materials and structures using numerical simulation, as a complement of theory and experiment. In this thesis, peridynamics is adopted to study fatigue and dynamic failure problems.

Fatigue is a major failure mode in engineering structures. Predicting fracture/failure under cyclic loading is a challenging problem. Classical model cannot directly be applied to problems with discontinuities. A peridynamic model is adopted in this work because of important advantages of peridynamics in allowing autonomous crack initiation and propagation. A recently proposed peridynamic fatigue crack model is considered …

Near-Field Thermal Radiation For Solar Thermophotovoltaics And High Temperature Thermal Logic And Memory Applications, Mahmoud Elzouka

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This dissertation investigates Near-Field Thermal Radiation (NFTR) applied to MEMS-based concentrated solar thermophotovoltaics (STPV) energy conversion and thermal memory and logics. NFTR is the exchange of thermal radiation energy at nano/microscale; when separation between the hot and cold objects is less than dominant radiation wavelength (~1 μm). NFTR is particularly of interest to the above applications due to its high rate of energy transfer, exceeding the blackbody limit by orders of magnitude, and its strong dependence on separation gap size, surface nano/microstructure and material properties.

Concentrated STPV system converts solar radiation to electricity using heat as an intermediary through a …

Fabrication And Study Of The Structure And Magnetism Of Rare-Earth Free Nanoclusters, Bhaskar Das

Department of Physics and Astronomy: Dissertations, Theses, and Student Research

No abstract provided.