Materials Science and Engineering Commons^™

Voltage-Controlled Magnetic Anisotropy In Antiferromagnetic Mgo-Capped Mnpt Films, P. H. Chang, Wuzhang Fang, T. Ozaki, Kirill Belashchenko

Kirill Belashchenko Publications

The magnetic anisotropy in MgO-capped MnPt films and its voltage control are studied using first-principles calculations. Sharp variation of the magnetic anisotropy with film thickness, especially in the Pt-terminated film, suggests that it may be widely tuned by adjusting the film thickness. In thick films the linear voltage control coefficient is as large as 1.5 and -0.6 pJ/Vm for Pt-terminated and Mn-terminated interfaces, respectively. The combination of a widely tunable magnetic anisotropy energy and a large voltage-control coefficient suggest that MgO-capped MnPt films can serve as a versatile platform for magnetic memory and antiferromagnonic applications.

Development Of An Intraperitoneal Catheter Placement Device For Use On The Battlefield, Riley Reynolds

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The objective of this project was to simplify peritoneal cavity access so an Airforce field medic can safely infuse oxygen microbubbles (OMBs) into the intraperitoneal space for the emergency treatment of hypoxia due to lung damage. To solve this problem, we created an intraperitoneal catheter placement device for use on the battlefield. The three common methods and some of the most common devices for peritoneal cavity access were reviewed. Injury frequencies for each of the three methods were analyzed. The results showed that each of the access techniques gives a similar rate of iatrogenic injury.

The battlefield conditions where the …

Growth And Characterization Of Molecular Ferroelectric Thin Films, Yifan Yuan

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Compared with inorganic ferroelectrics, organic ferroelectrics have advantages of low cost and low toxicity, are in increasing demand in capacitors, piezoelectric, and memory devices to reduce the environmental load. This work focuses on two types of organic molecular ferroelectric materials, croconic acid (CA) and 2-methylbenzimidazole (MBI). The work here introduces several origins of ferroelectricity in typical organics and their switching mechanism. We then investigated the nucleation, growth, and ferroelectric measurements of CA thin films. We explored the effect of substrate temperature and an external electric field on the nucleation and growth processes. The results can be used to improve the …

In-Service Performance Evaluation And Installation Recommendations For Cable Median Barriers On Non-Continuously Shielded, Divided-Median Kansas Freeways, Nathan Dowler

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The Kansas Department of Transportation (KDOT) installed 7.95 miles of cable median barrier (CMB) along K-10, K-96, and US-75 freeways in 2011 and 2012. In January 2020, KDOT funded a study to determine the in-service performance of its CMBs. In addition, KDOT sought to determine if it was cost-effective to modify guidelines for installing median barriers, which were based on annual daily traffic and median width.

Researchers reviewed every crash within approximately ¼ mile of a CMB installation and extracted crashes which involved a CMB impact. Researchers analyzed the critical details of each CMB crash, with particular emphasis on penetrations, …

On Road Coordinates For Autonomous Vehicle Guidance, Ricardo Jacome

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A new roadmap framework is proposed to improve the guidance and trajectory prediction capabilities of connected and automated vehicles (CAVs). Independent of road shape determination through external sensors, the system serves as a backup for challenging conditions, such as low sensor visibility and adverse environmental effects (e.g., rain, fog, snow). Based on the fusion of vehicle dynamics principles, differential geometry, and road design standards, the roadmap framework provides a consolidated collection of critical reference points of roadway centerlines and information about the shape of the roadway in the vicinity of a vehicle, including curvature, optimal travel velocity, and road alignment …

Surface Acoustic Waves Increase Magnetic Domain Wall Velocity, Anil Adhikari, Shireen Adenwalla

Shireen Adenwalla Papers

Domain walls in magnetic thin films are being explored for memory applications and the speed at which they move has acquired increasing importance. Magnetic fields and currents have been shown to drive domain walls with speeds exceeding 500 m/s. We investigate another approach to increase domain wall velocities, using high frequency surface acoustic waves to create standing strain waves in a 3 micron wide strip of magnetic film with perpendicular anisotropy. Our measurements, at a resonant frequency of 248.8 MHz, indicate that domain wall velocities increase substantially, even at relatively low applied voltages. Our findings suggest that the strain wave …

Ultrafast Spin-Currents And Charge Conversion At 3d-5d Interfaces Probed By Time-Domain Terahertz Spectroscopy, T. H. Dang, J. Hawecker, E. Rongione, G. Baez Flores, D. Q. To, J. C. Rojas-Sanchez, H. Nong, J. Mangeney, J. Tignon, F. Godel, S. Collin, P. Seneor, M. Bibes, A. Fert, M. Anane, J. M. George, L. Vila, M. Cosset-Cheneau, D. Dolfi, R. Lebrun, P. Bortolotti, Kirill Belashchenko, S. Dhillon, H. Jaffrès

Kirill Belashchenko Publications

Spintronic structures are extensively investigated for their spin-orbit torque properties, required for magnetic commutation functionalities. Current progress in these materials is dependent on the interface engineering for the optimization of spin transmission. Here, we advance the analysis of ultrafast spin-charge conversion phenomena at ferromagnetic-Transition metal interfaces due to their inverse spin-Hall effect properties. In particular, the intrinsic inverse spin-Hall effect of Pt-based systems and extrinsic inverse spin-Hall effect of Au:W and Au:Ta in NiFe/Au:(W,Ta) bilayers are investigated. The spin-charge conversion is probed by complementary techniques-ultrafast THz time-domain spectroscopy in the dynamic regime for THz pulse emission and ferromagnetic resonance spin-pumping …

Fluid Modeling And Analysis Of A Mash Tl-6 Vehicle Model, Elisa Vasquez

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The objective of this research project was to replicate the dynamic behavior of a truck-tank trailer combination vehicle using representative dimensions, properties, and inertias of the trailer/fluid ballast combination. A literature review was completed describing techniques for modeling fluids and fluid-container interactions using finite element analysis. Various fluid modeling techniques were identified, and parameters associated with those models were archived. Next, researchers utilized the tank geometry of the elliptical straight-frame 5949 trailer produced by LBT Inc. to generate a finite element mesh using finite element analysis preprocessors HyperMesh and LS PrePost. Material properties were taken from reference guides, research papers, …

Toward Understanding Underlying Mechanisms Of Drag Reduction In Turbulent Flow Control, Alex Rogge

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The underlying mechanisms of three different flow-control strategies on drag reduction in a turbulent channel flow are investigated by direct numerical simulations. These strategies include the addition of a small concentration of long-chain polymers into a fluid, the incorporation of slip surfaces, and the application of an external body force. While it has been believed that such methods lead to a skin-friction reduction by controlling near-wall flow structures, the underlying mechanisms at play are still not as clear. In this study, a temporal analysis is employed to elucidate underlying drag-reduction mechanisms among these methods. The analysis is based on the …

Machine Learning Augmentation Micro-Sensors For Smart Device Applications, Mohammad H. Hasan

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Novel smart technologies such as wearable devices and unconventional robotics have been enabled by advancements in semiconductor technologies, which have miniaturized the sizes of transistors and sensors. These technologies promise great improvements to public health. However, current computational paradigms are ill-suited for use in novel smart technologies as they fail to meet their strict power and size requirements. In this dissertation, we present two bio-inspired colocalized sensing-and-computing schemes performed at the sensor level: continuous-time recurrent neural networks (CTRNNs) and reservoir computers (RCs). These schemes arise from the nonlinear dynamics of micro-electro-mechanical systems (MEMS), which facilitates computing, and the inherent ability …

Proximity-Induced Magnetization In Graphene: Towards Efficient Spin Gating, Mihovil Bosnar, Ivor Lončarić, P. Lazić, Kirill Belashchenko, Igor Žutić

Kirill Belashchenko Publications

Gate-tunable spin-dependent properties could be induced in graphene at room temperature through the magnetic proximity effect by placing it in contact with a metallic ferromagnet. Because strong chemical bonding with the metallic substrate makes gating ineffective, an intervening passivation layer is needed. Previously considered passivation layers result in a large shift of the Dirac point away from the Fermi level, so that unrealistically large gate fields are required to tune the spin polarization in graphene (Gr). We show that a monolayer of Au or Pt used as the passivation layer between Co and graphene brings the Dirac point closer to …

Detection Of Uncompensated Magnetization At The Interface Of An Epitaxial Antiferromagnetic Insulator, Pavel N. Lapa, Min Han Lee, Igor V. Roshchin, Kirill Belashchenko, Ivan K. Schuller

Kirill Belashchenko Publications

We have probed directly the temperature and magnetic field dependence of pinned uncompensated magnetization at the interface of antiferromagnetic FeF₂ with Cu, using FeF₂-Cu-Co spin valves. Electrons polarized by the Co layer are scattered by the pinned uncompensated moments at the FeF₂-Cu interface giving rise to giant magnetoresistance. We determined the direction and magnitude of the pinned uncompensated magnetization at different magnetic fields and temperatures using the angular dependencies of resistance. The strong FeF₂ anisotropy pins the uncompensated magnetization along the easy axis independent of the cooling field orientation. Most interestingly, magnetic fields as …

Reinvestigation Of The Intrinsic Magnetic Properties Of (Fe1-Xcox)2b Alloys And Crystallization Behavior Of Ribbons, Tej Nath Lamichhane, Olena Palasyuk, Vladimir P. Antropov, Ivan A. Zhuravlev, Kirill Belashchenko, Ikenna C. Nlebedim, Kevin W. Dennis, Anton Jesche, Matthew J. Kramer, Sergey L. Bud'ko, R. William Mccallum, Paul C. Canfield, Valentin Taufour

Kirill Belashchenko Publications

New determination of the magnetic anisotropy from single crystals of (Fe_1-xCo_x)2B alloys are presented. The anomalous temperature dependence of the anisotropy constant is discussed using the standard Callen-Callen theory, which is shown to be insufficient to explain the experimental results. A more material specific study using first-principles calculations with disordered moments approach gives a much more consistent interpretation of the experimental data. Since the intrinsic properties of the alloys with x=0.3-0.35 are promising for permanent magnets applications, initial investigation of the extrinsic properties are described, in particular the crystallization of melt spun ribbons with Cu, Al, …

Wavelength Decomposition Of Hybrid Additive Manufacturing Power Signals And Their Relationship With Surface Integrity, Xingtao Wang

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Additive Manufacturing (AM) has been a promising manufacturing technology in industrial applications and gained a massive amount of attention from researchers all over the world. Directed Energy Deposition (DED) is an AM process in which focused thermal energy is used to fuse materials by melting as they are deposited. One of the most significant challenges involved in current metal AM processes is improving repeatability and consistency. Substantial effort has already been invested in this area of research.

In this dissertation, a milling tool not only played a role in subtractive manufacturing but also acted as a method of monitoring the …

Automatic Delamination Segmentation For Bridge Deck Based On Encoder-Decoder Deep Learning Through Uav-Based Thermography, Chongsheng Cheng, Zhexiong Shang, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Concrete deck delamination often demonstrates strong variations in size, shape, and temperature distribution under the influences of outdoor weather conditions. The strong variations create challenges for pure analytical solutions in infrared image segmentation of delaminated areas. The recently developed supervised deep learning approach demonstrated the potentials in achieving automatic segmentation of RGB images. However, its effectiveness in segmenting thermal images remains under-explored. The main challenge lies in the development of specific models and the generation of a large range of labeled infrared images for training. To address this challenge, a customized deep learning model based on encoder-decoder architecture is proposed …

In-Service Performance Evaluation Of Concrete Sloped End Treatments In Iowa, Jessica Lingenfelter

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Sloped end treatments were historically developed as low-cost, low-maintenance end treatments for rigid features like concrete barriers and bridge rails. Crash testing indicated that sloped end treatments are associated with significant instability for impacting vehicles. However, the in-service performance of these features has not been evaluated. An in-service performance evaluation (ISPE) was performed to evaluate vehicle crashes with sloped end treatments in Iowa between 2008 and 2017. Researchers generated a geographic inventory of sloped end treatment locations, reviewed crash narratives and scene diagrams for crashes near these sloped end treatments, and calculated an estimated crash rate and crash cost for …

Development Of A Novel Vehicle Guidance System: Vehicle Risk Mitigation And Control, Michael Sweigard

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Over a half of fatal vehicular crashes occur due to vehicles leaving their designated travel lane and entering other lanes or leaving the roadway. Lane departure accidents also result in billions of dollars in cost to society. Recent vehicle technology research into driver assistance and vehicle autonomy has developed to assume various driving tasks. However, these systems are do not work for all roads and travel conditions. The purpose of this research study was to begin the development a novel vehicle guidance approach, specifically studying how the vehicle interacts with the system to detect departures and control the vehicle

A …

Evaluation And Update Of Mash Test Vehicles, Kellon B. Ronspies

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The Manual for Assessing Safety Hardware (MASH) requires full-scale crash testing of roadside features using worst practical impact conditions. Vehicle selection for full-scale crash testing is intended to be representative of the contemporary passenger vehicle fleet. Researchers at the Midwest Roadside Safety Facility (MwRSF) investigated attributes of passenger vehicle sales to determine if the vehicle selection criteria shown in MASH should be revised to accommodate changes in the vehicle fleet. A methodology was considered to affordably re-analyze the vehicle fleet when necessary to ensure MASH vehicle selection criteria are reflective of vehicles currently on roadways.

Representative vehicles were documented using …

Thermal Modeling Of Additive Manufacturing Using Graph Theory: Validation With Directed Energy Deposition, Jordan Severson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Metal additive manufacturing (AM/3D printing) offers unparalleled advantages over conventional manufacturing, including greater design freedom and a lower lead time. However, the use of AM parts in safety-critical industries, such as aerospace and biomedical, is limited by the tendency of the process to create flaws that can lead to sudden failure during use. The root cause of flaw formation in metal AM parts, such as porosity and deformation, is linked to the temperature inside the part during the process, called the thermal history. The thermal history is a function of the process parameters and part design.

Consequently, the first step …

Quantifying Wicking In Functionlized Surfaces, Maureen Winter, Ryan Regan, Alfred Tsubaki, Craig Zuhlke, Dennis Alexander, George Gogos

UCARE: Research Products

Wicking remains the enigmatic key factor in many research areas. From boiling in power plants, to anti-icing on plane wings, to medical instruments, to heat pipes, efficiency and safety depend on how quickly a surface becomes wet. Yet wicking remains difficult to quantify and define as a property of the surface. This experiment strives to measure the wicking property by examining the rate that a liquid can be pulled out of a container. A superhydrophilic surface is placed in contact with the liquid at the bottom of a tube so that the volume flow rate across the surface can be …

Questaal: A Package Of Electronic Structure Methods Based On The Linear Muffin-Tin Orbital Technique, Dimitar Pashov, Swagata Acharya, Walter R.L. Lambrecht, Jerome Jackson, Kirill Belashchenko, Athanasios Chantis, Francois Jamet, Mark Van Schilfgaarde

Kirill Belashchenko Publications

This paper summarises the theory and functionality behind Questaal, an open-source suite of codes for calculating the electronic structure and related properties of materials from first principles. The formalism of the linearised muffin-tin orbital (LMTO) method is revisited in detail and developed further by the introduction of short-ranged tight-binding basis functions for full-potential calculations. The LMTO method is presented in both Green's function and wave function formulations for bulk and layered systems. The suite's full-potential LMTO code uses a sophisticated basis and augmentation method that allows an efficient and precise solution to the band problem at different levels of theory, …

Synthesis Of Sic Resin For 3d Printing Of Sic Ceramics By Digital Light Processing, Kevin Zhao, Bai Cui

UCARE: Research Products

Silicon carbide (SiC) resin is produced through shear mixing 0.1-1 μm SiC powders with Tethon’s high load Genesis resin base. Resins of varying SiC vol.% were synthesized to test the loading limit of the resin base; 10, 20, and 30 vol.% of SiC were made with the resin base handling the higher loads quite well. Several attempts were made at printing using the Tethon Bison 1000 DLP printer with higher loads of SiC showing better results even with lower intensity UV lights andtimes.

Effects Of Intrinsic Defects And Alloying With Fe On The Half-Metallicity Of Co2Mnsi, G. G. Baez Flores, Ivan A. Zhuravlev, Kirill Belashchenko

Kirill Belashchenko Publications

The electronic structure and half-metallic gap of Co2MnSi in the presence of crystallographic defects, partial Fe substitution for Mn, and thermal spin fluctuations are studied using the coherent potential approximation and the disordered local moment method. In the presence of 5% Co or Mn vacancies the Fermi level shifts down to the minority-spin valence-band maximum. In contrast to NiMnSb, both types of Mn antisite defects in Co2MnSi are strongly exchange coupled to the host magnetization, and thermal spin fluctuations do not strongly affect the half-metallic gap. Partial substitution of Mn by Fe results in considerable changes in the Bloch spectral …

Anomalous Eutectic Microstructures In Mg–Al Structural Alloy Prepared By Rapid Solidification, Soodabeh Azadehranjbar, Jian Wang, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Magnesium is the lightest engineering metal 1 However, conventional Mg alloys typically suffer from low strength and poor deformability due to very few slip systems and easy twinning 3 Alloying Mg with other materials and microstructural engineering are promising approaches to increase ductility and strength of Mg In the current work, non equilibrium solidification conditions were applied to induce a transition from regular to anomalous eutectic in Mg Al eutectic alloy such that four distinguished microstructures were acquired and the corresponding formation mechanisms were investigated

Experimental Study On The Characteristics Of Formation And Dissociation Of Co2 Hydrates In Porous Media, Amin Hosseini Zadeh, Ijung Kim, Seunghee Kim

Department of Civil and Environmental Engineering: Faculty Publications

Geologic carbon sequestration (GCS) has pursued as a feasible strategy to store the large amount of CO₂ to curb its emission to the atmosphere in an effort to mitigate the greenhouse effects. CO₂ hydrate, which can form when the pressure and temperature satisfy its stability condition, can provide a self-trapping mechanism for an offshore CO₂ geologic storage. For example, direct sequestration of CO₂ in the form of hydrate cystals an be achieved in the storage zone an potentially provide a secondary caprock. These application, however, require a thorough understanding of the formation and dissociation of CO …

On Geometric Design Rules And In-Process Build Quality Monitoring Of Thin-Wall Features Made Using Laser Powder Bed Fusion Additive Manufacturing Process, Aniruddha Gaikwad

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The goal of this thesis is to quantify the link between the design features (geometry), in-process signatures, and build quality of parts made using the laser powder bed fusion (LPBF) additive manufacturing (AM) process. This knowledge is the foundational basis for proposing design rules in AM, as well as for detecting the impending build failures using in-process sensor data.

As a step towards this goal, the objectives of this work are two-fold:

1) Quantify the effect of the geometry and orientation on the build quality of thin-wall features. To explain further, the geometry related factor is the ratio of the …

Multiscale Modeling Of Fracture In Quasi-Brittle Materials Using Bifurcation Analysis And Element Elimination Method, Keyvan Zare Rami

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Analyzing the fracture of heterogeneous materials is a complex problem, due to the fact that the mechanical behavior of a heterogeneous material is strongly dependent on a variety of factors, such as its microstructure, the properties of each constituent, and interactions between them. Therefore, these factors must be effectively taken into account for accurate analysis, for which the multiscale method has been widely used. In this scheme, the computational homogenization method is used to obtain the effective macroscopic properties of a heterogeneous material based on the response of a Representative Volume Element (RVE). The growth of damage in an RVE …

Bioresorbable Composite Stents For Enhanced Response Of Vascular Smooth Muscle Cells, Hozhabr Mozafari

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Formation of arterial plaque and stenosis is one of the main cardiovascular disease risk factors. Stenting is a popular approach to increase the inner diameter of the artery and provide an acceptable lumen gain. This is achieved by applying internal pressure to the arterial wall. Despite the desirable outcomes of this procedure, there are complexities and challenges that are being discussed among scholars in this area. Restenosis is one of these complications, in which smooth muscles cell start proliferation and remodeling in response of induced mechanical stresses. Another important issue is the placement of the stent and possible migration due …

Development Of A Mix Design Adjustment Method For Fiber Reinforced Concrete And Super High Performance Concrete Based On Excess Paste, Joe Malloy

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The main objective of this study was to develop a mix design adjustment method for Fiber Reinforced Concrete (FRC) that would maintain appropriate workability while improving hardened concrete performance. A literature review was conducted to examine existing methods for adjusting mix designs to account for fiber introduction. It was found that while increasing fine aggregate and cement paste content can make up for lost workability with the addition of fibers, no rational mix design adjustment method is available. Reference mix designs from the Nevada Department of Transportation and the Nebraska Department of Transportation were used, and this study focused on …

Nanothermomechanical Logic Gates For Thermal Computing, Ahmed Hamed

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Limited performance and reliability of electronic devices at extreme temperatures, intensive electromagnetic fields, and radiation found in space exploration missions (i.e., Venus & Jupiter planetary exploration, and heliophysics missions) and earth-based applications require the development of alternative computing technologies. Thermal computing, data processing based on heat instead of electricity, is proposed as a practical alternative and opens a new scientific area at the interface between thermal and computational sciences.

We successfully developed thermal AND, OR and NOT logic gates, achieved through the coupling between near-field thermal radiation and MEMS thermal actuation. In the process, we developed two novel non-linear thermal …