Materials Science and Engineering Commons^™

Pathways For Mitigating Thermal Losses In Solar Photovoltaics, Rodolphe Vaillon, Oliver Dupre, Raúl Bayoán Cal, Marc Calaf

Mechanical and Materials Engineering Faculty Publications and Presentations

To improve the performance of solar photovoltaic devices one should mitigate three types of losses: optical, electrical and thermal. However, further reducing the optical and electrical losses in modern photovoltaic devices is becoming increasingly costly. Therefore, there is a rising interest in minimizing the thermal losses. These correspond to the reduction in electrical power output resultant of working at temperatures above 25 °C and the associated accelerated aging. Here, we quantify the impact of all possible strategies to mitigate thermal losses in the case of the mainstream crystalline silicon technology. Results indicate that ensuring a minimum level of conductive/convective cooling …

Turbulence, Entrainment And Low-Order Description Of A Transitional Variable-Density Jet, Bianca Viggiano, Tamara S. Dib, N. Ali, L. G. Mastin, Raúl Bayoán Cal, S. A. Solovitz

Mechanical and Materials Engineering Faculty Publications and Presentations

Geophysical flows occur over a large range of scales, with Reynolds numbers and Richardson numbers varying over several orders of magnitude. For this study, jets of different densities were ejected vertically into a large ambient region, considering conditions relevant to some geophysical phenomena. Using particle image velocimetry, the velocity fields were measured for three different gases exhausting into air – specifically helium, air and argon. Measurements focused on both the jet core and the entrained ambient. Experiments considered relatively low Reynolds numbers from approximately 1500 to 10 000 with Richardson numbers near 0.001 in magnitude. These included a variety of …

Microstructure And Mechanical Properties Of Additive Manufacturing Titanium Alloys After Thermal Processing, Ahmet Alptug Tanrikulu

Dissertations and Theses

Titanium alloys are widely used for aerospace and biomaterial applications since their high specific strength, and high corrosion resistivity. Besides these properties, titanium is an excellent biocompatible material widely used for internal body implants. Because the products have complex geometries in both applications, Additive Manufacturing (AM) methods have been recently applied for production. AM methods can process a direct 3-D shape of the final product, decrease total production time and cost. However, high residual stress of the final product limits the application of AM components, especially the ones that are exposed to cyclic loading. In the present study, the initial …

Understanding Photovoltaic Properties Of Pbs Quantum Dot Solids Via Solution Contacting, Vitalii Dereviankin, Erik Johansson

Student Research Symposium

Photovoltaic (PV) devices based on PbS quantum dot (QD) solids demonstrate high photontoelectron conversion yields. However, record power conversion efficiency remain low, in part due to small photovoltages, which in turn are affected by both bulk and interfacial defects. Their relative impacts on limiting the photovoltaic performance of QD solids are not known. Interfacial defects can be formed when contacting a semiconductor and may dominate the semiconductor/metal or metaloxide junction properties. The objective of this study is to explore whether electrochemical contacting using liquid electrolytes provides means of contacting QD solids without introducing interfacial defects. We have initially focused on …

Flux Focusing Axial Magnetic Gear, Robert J. Rutherford

Undergraduate Research & Mentoring Program

Power transmission is traditionally achieved with a mechanical gear. These gears require maintenance, cause vibration, and have no overload protection. Magnetic gears (MGs) offer an innovative solution to these drawbacks as they do not require regular maintenance, have no need for lubrication, create very little acoustic noise, have built in overload protection and as a result of these advantages, have a longer lifetime of operation. The flux focusing axial magnetic gear (FFAMG) was assembled for future testing of power transmission, conversion, and generation applications.

Gears are used to transmit power by converting low speed-high torque rotary motion into high speed-low …

The Effect Of Plasma On Graphene Quality In An Inductively Couple Plasma Chemical Vapor Deposition Reactor, Brendan Coyne

Undergraduate Research & Mentoring Program

Despite continued interest in research and application development, full scale graphene production is still limited by many factors including prohibitively high growth temperature requirements. Extremely high quality graphene growth is possible at high temperatures using chemical vapor deposition (CVD). Use of an inductively coupled plasma chemical vapor deposition (ICP CVD) reactor with the benefit of precursor gas decomposition through plasma generation, may provide possibility to reduce growth temperature. Herein, we report plasma’s effects on graphene growth by comparing growths of increasing power supplied to plasma generation and changes in precursor gas ratios. Plasma composition was characterized by ultraviolet and visible …

Jet Bounce In Low Gravity, Caleb Turner

Undergraduate Research & Mentoring Program

Liquid jets rebound (‘bounce’) from superhydrophobic surfaces when they impinge at oblique angles. We call this interesting phenomena ‘jet bounce’ and in this work we investigate the phenomena at large length scales in a reduced gravitational environment. For example, for water at Reynolds numbers 0 < Re < 3500 and surface normal Weber numbers 0 < We < 60 we characterize the response of the jets on the hydrophobic surface in the brief 2.1s micro-gravity environment achieved using a drop tower. It is observed that by varying jet velocity, flow rate, jet diameter, and incident angle we observe up to four distinct regimes of behavior. The various regimes may be targeted for specific applications and we demonstrate a variety of unique jet bounce behaviors for applications such as no-touch, no-contact fluid-thermal transport for spacecraft unit operations such as contaminated water processing, device cooling, and cryogenic fluids transport and management.

Stable jet bounce from small diameter jet ≈ 1 mm and low impact angle. Characterizing Reynolds number ≈ 900 and normal Weber number ≤ 10 allow jet bounce to rebound in non-destructive behavior.

Conditional Averaging And Classification In The Near Wake Of A Wind Turbine Array Boundary Layer, Sarah E. Smith

Undergraduate Research & Mentoring Program

Flow perturbation induced by interaction with a turbine rotor produces considerable turbulence which can alter the productivity of subsequent units within a wind farm. Previous methods have characterized near wake vorticity of a single turbine as well as recovery distance for various turbine array configurations. This study aims to build from previous methods of analysis from the perspective of the rotor well within a turbine array and develop a model to examine points of significant imposition in relation to rotational effects. Hot wire anemometry was employed downstream of a turbine located in the middle of the third row in a …

Deposition Velocity Dependence On Urban Morphology, Rawand Muzafar Rasheed

Undergraduate Research & Mentoring Program

Understanding the interactions between the atmospheric boundary layer and urban structures provides insights into emerging problems such as green building design as well as dispersion and deposition of pollutants on urban structures. Characterization of deposition velocity dependence through the naphthalene sublimation method on model urban structures is conducted herein where the analogous fundamental transport mechanisms of momentum and mass transport is obtained via mass of naphthalene transferred. Via wind tunnel experiments, results show that deposition velocity of naphthalene from urban structures increases with increased number of urban structures ahead of the point of investigation. This is attributed to the wakes …

The Effectiveness Of Sanitary Inspections As A Risk Assessment Tool For Thermotolerant Coliform Bacteria Contamination Of Rural Drinking Water: A Review Of Data From West Bengal, India, Christian Snoad, Corey L. Nagel, Animesh Bhattacharya, Evan A. Thomas

Mechanical and Materials Engineering Faculty Publications and Presentations

The use of sanitary inspections combined with periodic water quality testing has been recommended in some cases as screening tools for fecal contamination. We conducted sanitary inspections and tested for thermotolerant coliforms (TTCs), a fecal indicator bacteria, among 7,317 unique water sources in West Bengal, India. Our results indicate that the sanitary inspection score has poor ability to identify TTC-contaminated sources. Among deep and shallow hand pumps, the area under curve (AUC) for prediction of TTC > 0 was 0.58 (95% confidence interval [CI] = 0.53–0.61) and 0.58 (95% CI = 0.54–0.62), respectively, indicating that the sanitary inspection score was only …

Development And Training Of A Neural Controller For Hind Leg Walking In A Dog Robot, Alexander J. Hunt, Nicholas Szczecinski, Roger Quinn

Mechanical and Materials Engineering Faculty Publications and Presentations

Animals dynamically adapt to varying terrain and small perturbations with remarkable ease. These adaptations arise from complex interactions between the environment and biomechanical and neural components of the animal’s body and nervous system. Research into mammalian locomotion has resulted in several neural and neuro-mechanical models, some of which have been tested in simulation, but few “synthetic nervous systems” have been implemented in physical hardware models of animal systems. One reason is that the implementation into a physical system is not straightforward. For example, it is difficult to make robotic actuators and sensors that model those in the animal. Therefore, even …

Building Energy Model Calibration For Retrofit Decision Making, Nicolas R. Johnson

Dissertations and Theses

Accommodating the continued increase in energy demand in the face of global climate change has been a worldwide concern. With buildings in the US consuming nearly 40% of national energy, a concerted effort must be given to reduce building energy consumption. As new buildings continue to improve their efficiency through more restrictive energy codes, the other 76.9 billion square feet of current building stock falls further behind. The rate at which current buildings are being retrofit is not enough and better tools are needed to access the benefits of retrofits and the uncertainties associated with them. This study proposes a …

Reversible Control Of The Magnetization Of Fe₃O₄ Via Lithium Ions, Guodong Wei, Lin Wei, Dong Wang, Yufeng Tian, Yanxue Chen, Shishen Yan, Liangmo Mei, Jun Jiao

Mechanical and Materials Engineering Faculty Publications and Presentations

In this report, a reversible control of Fe₃O₄ saturated magnetization by Li ions is demonstrated. A miniature Li ion battery (LIB) was assembled using a Fe₃O₄ nanoparticle layer as the active cathode. A stable magnetism modulation is realized by a nondestructive electrochemical process in which the lithium insertion results in a valence change and partial redistribution of Fe cations in the crystal structure. The relation between the discharge voltage and the chemical phases were studied by ex situ X-ray diffraction and magnetic measurement. In a suitable discharge potential range, a reversible control of Fe₃O₄ saturated magnetization was obtained without structural …

Fifty-Plus-Year Postflight Analysis Of First Fluid Experiment Aboard A Spacecraft, Mark M. Weislogel, Yongkang Chen, William J. Masica, Fred J. Kohl, Robert D. Green

Mechanical and Materials Engineering Faculty Publications and Presentations

This year marks the 55th anniversary of the first fluid physics experiment performed aboard a spacecraft during the Mercury-Atlas 7 mission. Since then, NASA has conducted over 80 fluids physics experiments aboard a variety of spacecraft, many of which have enhanced the understanding of large-length-scale capillary phenomena relevant to liquid management in the weightless state. As both celebration and demonstration, the Mercury-Atlas 7 fluids experiment is revisited in light of the current understanding of large-length-scale capillary fluidics. Employing a modern numerical tool, a rich variety of experimental outcomes are discovered that were not observed during the flight experiment. Interestingly, experimental …

Reversible Control Of The Magnetization Of Spinel Ferrites Based Electrodes By Lithium-Ion Migration, Guodong Wei, Lin Wei, Dong Wang, Yanxue Chen, Yufeng Tian, Shishen Yan, Liangmo Mei, Jun Jiao

Mechanical and Materials Engineering Faculty Publications and Presentations

Lithium-ion (Li-ion) batteries based on spinel transition-metal oxide electrodes have exhibited excellent electrochemical performance. The reversible intercalation/deintercalation of Li-ions in spinel materials enables not only energy storage but also nondestructive control of the electrodes’ physical properties. This feature will beneft the fabrication of novel Li-ion controlled electronic devices. In this work, reversible control of ferromagnetism was realized by the guided motion of Li-ions in MnFe₂O₄ and γ-Fe₂O₃ utilizing miniature lithium-battery devices. The in-situ characterization of magnetization during the Li-ion intercalation/deintercalation process was conducted, and a reversible variation of saturation magnetization over 10% was observed …

Anisotropic Character Of Low-Order Turbulent Flow Descriptions Through The Proper Orthogonal Decomposition, Nicholas Hamilton, Murat Tutkun, Raúl Bayoán Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Proper orthogonal decomposition (POD) is applied to distinct data sets in order to characterize the propagation of error arising from basis truncation in the description of turbulence. Experimental data from stereo particle image velocimetry measurements in a wind turbine array and direct numerical simulation data from a fully developed channel flow are used to illustrate dependence of the anisotropy tensor invariants as a function of POD modes used in low-order descriptions. In all cases, ensembles of snapshots illuminate a variety of anisotropic states of turbulence. In the near wake of a model wind turbine, the turbulence field reflects the periodic …

Investigating Co2 Removal By Ca- And Mg-Based Sorbents With Application To Indoor Air Treatment, Elliott T. Gall, Cem Sonat, William W. Nazaroff, Cise Unluer

Mechanical and Materials Engineering Faculty Publications and Presentations

Indoor carbon dioxide (CO 2 ) levels serve as an indicator of ventilation sufficiency in relation to metabolic effluents. Recent evidence suggests that elevated CO 2 exposure (with or without other bioeffluents) may cause adverse cognitive effects. In shelter-in-place (SIP) facilities, indoor CO 2 levels may become particularly elevated. This study evaluates four low-cost alkaline earth metal oxides and hydroxides as CO 2 sorbents for potential use in indoor air cleaning applications. Sorbents studied were MgO, Mg(OH) 2 , Ca(OH) 2 and commercially available soda lime. Uncarbonated sorbents characterized with nitrogen adsorption porosimetry showed BET surface areas in the 5.6–27 …

Focused-Based Multifractal Analysis Of The Wake In A Wind Turbine Array Utilizing Proper Orthogonal Decomposition, Naseem Ali, Hawwa Falih Kadum, Raúl Bayoán Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Hot-wire anemometry measurements have been performed in a 3×3 wind turbine array to study the multifractality of the turbulent kinetic energy dissipation. A multifractal spectrum and Hurst exponents are determined at nine locations downstream of the hub height, bottom and top tips. Higher multifractality is found at 0.5D and 1D downstream of the bottom tip and hub height. The second order of the Hurst exponent and combination factor shows the ability to predict the flow state in terms of its development. Snapshot proper orthogonal decomposition (POD) is used to identify the coherent and incoherent structures and to reconstruct the stochastic …

Bioaerosol Deposition On An Air-Conditioning Cooling Coil, Yan Wu, Ailu Chen, Irvan Luhung, Elliott T. Gall, Qingliang Cao, Victor Wei-Chung Chang, William W. Nazaroff

Mechanical and Materials Engineering Faculty Publications and Presentations

This study is concerned with the role of a fin-and-tube heat exchanger in modifying microbial indoor air quality. Specifically, depositional losses of ambient bioaerosols and particles onto dry (not cooled) and wet (cool) coil surfaces were measured for different airspeeds passing through the test coil. Total, bacterial and fungal DNA concentrations in condensate water produced by a wet coil were also quantified by means of fluorescent dsDNA-binding dye and qPCR assays. Results revealed that the deposition of bioaerosols and total particles is substantial on coil surfaces, especially when wet and cool. The average deposition fraction was 0.14 for total DNA, …

Distribution Of Mean Kinetic Energy Around An Isolated Wind Turbine And A Characteristic Wind Turbine Of A Very Large Wind Farm, Gerard Cortina, Marc Calaf, Raul Bayoan Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

An isolated wind turbine and a very large wind farm are introduced into large-eddy simulations of an atmospheric boundary layer. The atmospheric flow is forced with a constant geostrophic wind and a time-varying surface temperature extracted from a selected period of the CASES-99 field experiment. A control volume approach is used to directly compare the transfer of mean kinetic energy around a characteristic wind turbine throughout a diurnal cycle considering both scenarios. For the very large wind farm case, results illustrate that the recovery of mean kinetic energy around a wind turbine is dominated by the vertical flux, regardless of …

Effect Of Fiber Material On Ozone Removal And Carbonyl Production From Carpets, Omed A. Abbass, David J. Sailor, Elliott T. Gall

Mechanical and Materials Engineering Faculty Publications and Presentations

Indoor air quality is affected by indoor materials such as carpets that may act as sources and/or sinks of gas-phase air pollutants. Heterogeneous reactions of ozone with carpets may result in potentially harmful products. In this study, indoor residential carpets of varying fiber types were tested to evaluate their ability to remove ozone, and to assess their role in the production of carbonyls when exposed to elevated levels of ozone. Tests were conducted with six types of new unused carpets. Two sets of experiments were conducted, the first measured ozone removal and ozone deposition velocities, and the second measured primary …

Puddle Jumping: Spontaneous Ejection Of Large Liquid Droplets From Hydrophobic Surfaces During Drop Tower Tests, Babek Attari, Mark M. Weislogel, Andrew Paul Wollman, Yongkang Chen, Trevor Snyder

Mechanical and Materials Engineering Faculty Publications and Presentations

Large droplets and puddles jump spontaneously from sufficiently hydrophobicsurfaces during routine drop tower tests. The simple low-cost passive mechanism can in turn be used as an experimental device to investigate dynamic droplet phenomena for drops up to 104 times larger than their normal terrestrial counterparts. We provide and/or confirm quick and qualitative design guides for such “drop shooters” as employed in drop tower tests including relationships to predict droplet ejection durations and velocities as functions of drop volume, surface texture, surface contour, wettability pattern, and fluid properties including contact angle. The latter is determined via profile image comparisons with numerical …

Inverse Structure Functions In The Canonical Wind Turbine Array Boundary Layer, Bianca Viggiano, Moira Gion, Naseem Ali, Murat Tutkun, Raúl Bayoán Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Wind tunnel measurements for a 3×3 canonical wind turbine array boundary layer are obtained using hot-wire anemometer velocity signals. Two downstream locations are considered, referring to the near- and far-wake, and 21 vertical points are acquired per profile. Velocity increments and exit distances are used to quantify inverse structure functions at both downstream locations. Inverse structure functions in the near-wake show a similar profile for the main vertical locations, but diverge as the moment is increased. In the far-wake, inverse structure functions converge toward a single function for all vertical location and moments. The scaling exponents for inverse structure functions …

High-Performance Self-Powered Photodetectors Based On Zno/Zns Core-Shell Nanorod Arrays, Hailing Lin, Lin Wei, Cuncun Wu, Yanxue Chen, Shishen Yan, Liangmo Mei, Jun Jiao

Mechanical and Materials Engineering Faculty Publications and Presentations

In recent years, there is an urgent demand for high-performance ultraviolet photodetectors with high photosensitivity, fast responsivity, and excellent spectral selectivity. In this letter, we report a self-powered photoelectrochemical cell-type UV detector using the ZnO/ZnS core-shell nanorod array as the active photoanode and deionized water as the electrolyte. This photodetector demonstrates an excellent spectral selectivity and a rapid photoresponse time of about 0.04 s. And the maximum responsivity is more than 0.056 (A/W) at 340 nm, which shows an improvement of 180 % compared to detectors based on the bare ZnO nanorods. This improved photoresponsivity can be understood from the …

Study Design Of A Cluster-Randomized Controlled Trial To Evaluate A Large-Scale Distribution Of Cook Stoves And Water Filters In Western Province, Rwanda, Corey L. Nagel, Miles Kirby, Laura D. Zambrano, Ghislaine Rosa, Christina K. Barstow, Evan A. Thomas, Thomas Clasen

Mechanical and Materials Engineering Faculty Publications and Presentations

Background: In Rwanda, pneumonia and diarrhea are the first and second leading causes of death, respectively, among children under five. Household air pollution (HAP) resultant from cooking indoors with biomass fuels on traditional stoves is a significant risk factor for pneumonia, while consumption of contaminated drinking water is a primary cause of diarrheal disease. To date, there have been no largescale effectiveness trials of programmatic efforts to provide either improved cookstoves or household water filters at scale in a low-income country. In this paper we describe the design of a clusterrandomized trial to evaluate the impact of a national-level program …

Column-Grid-Array (Cga) Versus Ball-Grid-Array (Bga): Boardlevel Drop Test And The Expected Dynamic Stress In The Solder Material, Ephraim Suhir, Reza Ghaffarian

Mechanical and Materials Engineering Faculty Publications and Presentations

Board level drop test is considered with an objective to develop a physically meaningful analytical predictive model for the evaluation of the expected impactinduced dynamic stresses in the solder material. Ball-gridarray (BGA) and column-grid-array (CGA) designs are addressed. Intuitively it is felt that while the application of the CGA technology to relieve thermal stresses in the solder material might be quite effective (owing to the greater interfacial compliance of the CGA in comparison with the BGA), the situation might be quite different when the PCB/package experiences dynamic loading. This is because the mass of the CGA joints exceeds considerably that …

Stabilization Of Vegetable Oil-Based Quenchants To Thermal-Oxidative Degradation: Experimental Strategy And Effect Of Oxidation On Quenching Performance, Éder Cícero Adão Simêncio, Rosa Lúcia Simêncio Otero, Lauralice De Campos Franceschini Canale, George E. Totten

Mechanical and Materials Engineering Faculty Publications and Presentations

Although petroleum oils continue to be the dominant type of basestock for the formulation of vaporizable quenchants, there is increasing pressure to identify an alternative basestock to address the limitations to their continued use because they are not a renewable basestock and they possess generally poor toxicity and biodegradability properties. Currently the most often cited alternative basestocks are those based on seed oils since they are renewable and usually non-toxic but especially because they are typically readily biodegradable. However, they suffer a critically important deficiency in that they are also typically much less stable to thermal-oxidative degradation than petroleum oils. …

More Investigations In Capillary Fluidics Using A Drop Tower, Andrew Paul Wollman, Mark M. Weislogel, Brentley M. Wiles, Donald Pettit, Trevor Snyder

Mechanical and Materials Engineering Faculty Publications and Presentations

A variety of contemplative demonstrations concerning intermediate-to-large length scale capillary fluidic phenomena were made possible by the brief weightless environment of a drop tower (Wollman and Weislogel in Exp Fluids 54(4):1, 2013). In that work, capillarity-driven flows leading to unique spontaneous droplet ejections, bubble ingestions, and multiphase flows were introduced and discussed. Such efforts are continued herein. The spontaneous droplet ejection phenomena (auto-ejection) is reviewed and demonstrated on earth as well as aboard the International Space Station. This technique is then applied to novel low-g droplet combustion where soot tube structures are created in the wakes of burning drops. …

Semiconductor Film Grown On A Circular Substrate: Predictive Modeling Of Lattice-Misfit Stresses, Ephraim Suhir, Johann Nicolics, G. Khatibi, M. Lederer

Mechanical and Materials Engineering Faculty Publications and Presentations

effective and physically meaningful analytical predictive model is developed for the evaluation the lattice-misfit stresses (LMS) in a semiconductor film grown on a circular substrate (wafer). The two-dimensional (plane-stress) theory-of-elasticity approximation (TEA) is employed in the analysis. The addressed stresses include the interfacial shearing stress, responsible for the occurrence and growth of dislocations, as well as for possible delaminations and the cohesive strength of a buffering material, if any. Normal radial and circumferential (tangential) stresses acting in the film cross-sections and responsible for its short- and long-term strength (fracture toughness) are also addressed. The analysis is geared to the GaN …

One-Dimensional Nanostructure And Sensing Applications: Tin Dioxide Nanowires And Carbon Nanotubes, Hoang Anh Tran

Dissertations and Theses

The key challenge for a nanomaterial based sensor is how to synthesize in bulk quantity and fabricate an actual device with insightful understanding of operational mechanisms during performance. I report here effective, controllable methods that exploit the concepts of the "green approach" to synthesize two different one-dimensional nanostructures, including tin oxide nanowires and carbon nanotubes. The syntheses are followed by product characterization and sensing device fabrications as well as sensor performance understanding at the molecular level. Sensor-analyte response and recovery kinetics are also presented.

The first part of the thesis describes bulk-scale synthesis and characterization of tin oxide nanowires by …