Materials Science and Engineering Commons^™

Structure Functions, Scaling Exponents And Intermittency In The Wake Of A Wind Turbine Array, Naseem Ali, Aleksandr Sergeyevich Aseyev, Raúl Bayoán Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Hot-wire measurements obtained in a 3 × 3 wind turbine array boundary layer are utilized to analyze high order structure functions, intermittency effects as well as the probability density functions of velocity increments at different scales within the energy cascade. The intermittency exponent is found to be greater in the far-wake region in comparison with the near-wake. At hub height, the intermittency exponent is found to be null. Extended self-similarity scaling exponents of the second, fourth, and fifth order structure functions remain relatively constant as a function of height in the far-wake; whereas in the near-wake, these are highly affected …

Engineered Mushing Cooker, Aimee Ritter

Undergraduate Research & Mentoring Program

This project revolves around building methanol cookers for dog mushers in the Iditarod and for the Denali Park Ranger Kennel in Denali National Park, Alaska. Traditional cookers are bulky, slow to burn, and use up a lot of fuel. Our goal has been to revolutionize the way mushing cookers look and perform. Our cookers are built to pack well in the sleds, heat up to 3 gallons of snowmelt, perform in arctic climates, use methanol (specifically HEET) for fuel, and be lightweight. A traditional cooker would use 3 to 4 bottles or more of HEET (36-48+oz.) and take at least …

Design For Fractal Grid Generated Turbulence, Moira Gion

Undergraduate Research & Mentoring Program

Fractal geometry can be used to find organization or order in something that appears to be in disorder, or chaos. Turbulence is viewed as one place where fractal geometry can be found in nature. The irregularity in fluid flow is dependent on the initial conditions. In the past, the idea of self-similarity has been used to develop statistical theories of energy cascade in a turbulent flow. Recent studies have done experiments on obstructing flows with fractal objects to observe intermittency, (or self-similarity) within a turbulent flow. Experiments on fractal grid generated turbulence has been performed by other research groups, so …

Complex Capillary Fluidic Phenomena For Passive Control Of Liquids In Low-Gravity Environments, Logan Torres

Undergraduate Research & Mentoring Program

In an effort to further apply the recent results of puddle jumping research, we seek to expand the oblique droplet impact studies of others by exploiting large liquid droplets in the near weightless environment of a drop tower. By using the spontaneous puddle jump mechanism, droplets of volumes 1 mL ≤ V ≤ 3 mL with corresponding Weber numbers of We ≈ 1 are impinged on surfaces inclined in the range 40° ≤ α ≤ 80° (measured from the horizontal plane). Impact surface wetting characteristics exhibit static contact angles θstatic = 165 ± 5°. All impacts result in complete rebound. …

Quantum Yield Optimization For Semiconductor Photocatalysis Systems, Ryan Catabay

Undergraduate Research & Mentoring Program

The utilization of photocatalysis has a well-known potential for mineralizing organic contaminants in water purification processes. A continuous flow photocatalytic reactor was developed in order to test the quantum yield of titanium dioxide, a semiconductor material well known for its photocatalytic properties. In order to build this reactor, multiple manufacturing methods were performed: manual and CNC machining, laser cutting, waterjet cutting, and chemical synthesis. A continuous flow reactor was particularly designed for a controlled, variable radiant flux of ultraviolet light. This continuous UV radiation excites the photocatalyst, generating electron hole pairs that form hydroxyl radicals, which in turn mineralize organic …

Real-Time Monitoring Of Personal Exposures To Carbon Dioxide, Elliott T. Gall, Toby Cheung, Irvan Luhung, Stefano Schiavon, William W. Nazaroff

Mechanical and Materials Engineering Faculty Publications and Presentations

Elevated indoor CO₂ levels are indicative of insufficient ventilation in occupied spaces and correlate with elevated concentrations of pollutants of indoor origin. Adverse health and well-being outcomes associated with elevated indoor CO₂ levels are based on CO₂ as a proxy, although some emerging evidence suggests CO₂ itself may impact human cognition. Using portable monitors, we conducted an exposure study with 16 subjects in Singapore to understand the levels, dynamics and influencing factors of personal exposure to CO₂. Participants carried a CO₂ monitor continuously for 7-day periods recording their exposure levels at 1-min intervals. …

Comparative Estimates Of Anthropogenic Heat Emission In Relation To Surface Energy Balance Of A Subtropical Urban Neighborhood, Changhyoun Park, Gunnar W. Schade, Nicholas D. Werner, David J. Sailor, Cheolhee Kim

Mechanical and Materials Engineering Faculty Publications and Presentations

Long-term eddy covariance measurements have been conducted in a subtropical urban area, an older neighborhood north of downtown Houston. The measured net radiation (Q*), sensible heat flux (H) and latent heat flux (LE) showed typical seasonal diurnal variations in urban areas: highest in summer; lowest in winter. From an analysis of a subset of the first two years of measurements, we find that approximately 42% of Q* is converted into H, and 22% into LE during daytime. The local anthropogenic heat emissions were estimated conventionally using the long-term residual method and the heat emission inventory approach. We also …

Effect Of Nano-Oxide Particle Size On Radiation Resistance Of Ironechromium Alloys, Weizong Xu, Lulu Li, James A. Valdez, Mostafa Saber, Yuntian Zhu, Carl C. Koch, Ronald O. Scattergood

Mechanical and Materials Engineering Faculty Publications and Presentations

Radiation resistance of Fe-14Cr alloys under 200 keV He irradiation at 500 ­*C was systematically investigated with varying sizes of nano oxide Zr, Hf and Cr particles. It is found that these nano oxide particles acted as effective sites for He bubble formation. By statistically analyzing 700-1500 He bubbles at the depth of about 150-700 nm from a series of HRTEM images for each sample, we established the variation of average He bubble size, He bubble density, and swelling percentage along the depth, and found them to be consistent with the He concentration profile calculated from the SIRM program. Oxide …

Ozone Reaction With Interior Building Materials: Influence Of Diurnal Ozone Variation, Temperature And Humidity, Donghyun Rim, Elliott T. Gall, Randy L. Maddalena, William W. Nazaroff

Mechanical and Materials Engineering Faculty Publications and Presentations

Elevated tropospheric ozone concentrations are associated with increased morbidity and mortality. Indoor ozone chemistry affects human exposure to ozone and reaction products that also may adversely affect health and comfort. Reactive uptake of ozone has been characterized for many building materials; however, scant information is available on how diurnal variation of ambient ozone influences ozone reaction with indoor surfaces. The primary objective of this study is to investigate ozone-surface reactions in response to a diurnally varying ozone exposure for three common building materials: ceiling tile, painted drywall, and carpet tile. A secondary objective is to examine the effects of air …

Long-Term Stability Of 14yt-4sc Alloy At High Temperature, Lulu Li, Weizong Xu, Mostafa Saber, Yuntian Zhu, Carl C. Koch, Ronald O. Scattergood

Mechanical and Materials Engineering Faculty Publications and Presentations

14YT alloy (Fe-14Cr-0.25wt.%Y2O3-0.4wt.%Ti) with 4 at.% Sc addition was previously reported to exhibit a nanoscale microstructure and high strength when annealed at temperatures up to 1000 °C (0.65Tm) for 1 hour. Here we report that the microstructure and mechanical behavior of 14YT-4Sc alloy after long-term annealing for up to 60 hours at 1000 °C. FIB analysis shows abnormal grain growth with annealing time, while a large fraction of the matrix still consists of nanoscale grains. TEM images reveal a slight growth of nano grains, with estimated grain growth exponent, n, to be 0.29. Sc-Ti-Y-O enriched nano oxide particles (nm) were …

Development Of A National Anthropogenic Heating Database With An Extrapolation For International Cities, David J. Sailor, Matei Georgescu, Jeffrey M. Milne, Melissa A. Hart

Mechanical and Materials Engineering Faculty Publications and Presentations

Given increasing utility of numerical models to examine urban impacts on meteorology and climate, there exists an urgent need for accurate representation of seasonally and diurnally varying anthropogenic heating data, an important component of the urban energy budget for cities across the world. Incorporation of anthropogenic heating data as inputs to existing climate modeling systems has direct societal implications ranging from improved prediction of energy demand to health assessment, but such data are lacking for most cities. To address this deficiency we have applied a standardized procedure to develop a national database of seasonally and diurnally varying anthropogenic heating profiles …

Capillary Channel Flow (Ccf) Eu2-02 On The International Space Station (Iss): An Experimental Investigation Of Passive Bubble Separations In An Open Capillary Channel, Mark M. Weislogel, Andrew P. Wollman, Ryan M. Jenson, John T. Geile, John F. Tucker, Brentley M. Wiles, Andy L. Trattner, Claire Devoe, Lauren M. Sharp, Peter J. Canfield, Jörg Klatte, Michael E. Dreyer

Mechanical and Materials Engineering Faculty Publications and Presentations

It would be signicantly easier to design fluid systems for spacecraft if the fluid phases behaved similarly to those on earth. In this research an open 15:8 degree wedge-sectioned channel is employed to separate bubbles from a two-phase flow in a microgravity environment. The bubbles appear to rise in the channel and coalesce with the free surface in much the same way as would bubbles in a terrestrial environment, only the combined effects of surface tension, wetting, and conduit geometry replace the role of buoyancy. The host liquid is drawn along the channel by a pump and noncondensible gas bubbles …

Constant Interface Temperature Reliability Assessment Method: An Alternative Method For Testing Thermal Interface Material In Products, Christian Amoah-Kusi

Dissertations and Theses

As electronic packages and their thermal solutions become more complex the reliability margins in the thermal solutions diminish and become less tolerant to errors in reliability predictions. The current method of thermally stress testing thermal solutions can be over or under predicting end of life thermal performance. Benefits of accurate testing and modeling are improved silicon yield in manufacturing, improved performance, lower cost thermal solutions, and shortened test times.

The current method of thermally stress testing is to place the entire unit in an elevated isothermal temperature and periodically measure thermal performance. Isothermally aging is not an accurate representation of …

Measuring The Effect Of Vegetated Roofs On The Performance Of Photovoltaic Panels In Combined Systems, Hamid Hawi Kadham Ogaili

Dissertations and Theses

Recent studies suggest that integration of photovoltaic panels with green roofs may improve the performance of both. While vegetation may provide a benefit by reducing the net radiation load on the underside of the photovoltaic (PV) panels, it may also affect convective cooling of panels, and consequently, panel efficiency. Both effects likely diminish with the height of the PV panel above the roof, although placing PV panels too close to the vegetation increases the risk of the plants growing over the edges of, and shading the PV panel. There is a gap in the literature with respect to evaluating these …

Thermodynamic Grain Size Stabilization Models: An Overview, Mostafa Saber, Carl C. Koch, Ronald O. Scattergood

Mechanical and Materials Engineering Faculty Publications and Presentations

Grain boundaries in a nanocrystalline microstructure produce an increase in the excess free energy of the system. Grain growth is a consequence of the thermodynamic driving force reducing this excess. Thermodynamic stabilization is an approach based on eliminating the driving force by suitable alloy additions that can produce a metastable equilibrium state at the nanoscale grain size, as opposed to kinetic stabilization where the grain growth mobility is restricted by pinning and/or drag mechanisms. The present paper reviews and compares various models proposed for thermodynamic stabilization.

Estimation Of Transient Temperature Distribution During Quenching, Via A Parabolic Model, Diego E. Lozano, Gabriela Martinez-Solis, Rafael David Mercado-Solis, Rafael Colás, George E. Totten

Mechanical and Materials Engineering Faculty Publications and Presentations

A material-independent model to estimate the transient temperature distribution in a test probe quenched by immersion is presented in this study. This model is based on the assumption that, under one-dimensional unsteady heat conduction, the radial temperature distribution at the end of an interval belongs to the equation of a parabola. The model was validated using AISI 304 stainless steel test probes (Φ8×40 mm and Φ12×60 mm) quenched from 850 to 900 °C in water and in water-based NaNO2 solutions at 25 °C and in canola oil at 50 °C. Additionally, square test probes (20×20×100 mm) were quenched from 550 …

Phase Transitions And In Situ Dynamics Of Crystal Grain Formation Of Alumina Nanotubes Templated By Vertically Aligned Carbon Nanotubes, L. F. Lampert, A. Barnum, S. W. Smith, J. F. Conley, Jun Jiao

Mechanical and Materials Engineering Faculty Publications and Presentations

Phase transitions of amorphous alumina (a-alumina) nanotubes grown by atomic layer deposition and templated by carbon nanotubes were investigated with thermal annealing, transmitted Kikuchi electron diffraction, electron-irradiation-induced crystallization, X-ray diffraction, and X-ray photoelectron spectroscopy. The resulting, engineered alumina nanotube arrays demonstrate a large range of tunable phases that are vital for understanding how alumina nanotube arrays can be applied for uses within biotechnology, catalysis, and other academic and industrial uses.

Anisotropy Of The Reynolds Stress Tensor In The Wakes Of Wind Turbine Arrays In Cartesian Arrangements With Counter-Rotating Rotors, Nicholas Hamilton, Raúl Bayoán Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

A 4 × 3 wind turbine array in a Cartesian arrangement was constructed in a wind tunnel setting with four configurations based on the rotational sense of the rotor blades. The fourth row of devices is considered to be in the fully developed turbine canopy for a Cartesian arrangement. Measurements of the flow field were made with stereo particle-image velocimetry immediately upstream and downstream of the selected model turbines. Rotational sense of the turbine blades is evident in the mean spanwise velocity W and the Reynolds shear stress −vw. The flux of kinetic energy is shown to be of greater …

Passive Phase Separation Of Microgravity Bubbly Flows Using Conduit Geometry, Ryan M. Jenson, Andrew Paul Wollman, Mark M. Weislogel, Lauren Sharp, Robert Green, Peter J. Canfield, Jörg Klatte, Michael E. Dreyer

Mechanical and Materials Engineering Faculty Publications and Presentations

The ability to separate liquid and gas phases in the absence of a gravitational acceleration has proven a challenge to engineers since the inception of space exploration. Due to our singular experience with terrestrial systems, artificial body forces are often imparted in multiphase fluid systems aboard spacecraft to reproduce the buoyancy effect. This approach tends to be inefficient, adding complexity, resources, and failure modes. Ever present in multiphase phenomena, the forces of surface tension can be exploited to aid passive phase separations where performance characteristics are determined solely by geometric design and system wettability. Said systems may be readily designed …

A Regression Approach For Estimation Of Anthropogenic Heat Flux Based On A Bottom-Up Air Pollutant Emission Database, Sanghyun Lee, Stuart A. Mckeen, David J. Sailor

Mechanical and Materials Engineering Faculty Publications and Presentations

A statistical regression method is presented for estimating hourly anthropogenic heat flux (AHF) using an anthropogenic pollutant emission inventory for use in mesoscale meteorological and air-quality modeling. Based on bottom-up AHF estimated from detailed energy consumption data and anthropogenic pollutant emissions of carbon monoxide (CO) and nitrogen oxides (NO_x) in the US National Emission Inventory year 2005 (NEI-2005), a robust regression relation between the AHF and the pollutant emissions is obtained for Houston. This relation is a combination of two power functions (Y = aX^b) relating CO and NO_x emissions to AHF, giving a determinant …

Experimental Investigation Of Lateral Cyclic Behavior Of Wood-Based Screen-Grid Insulated Concrete Form Walls, John Stuart Garth

Dissertations and Theses

Insulated concrete forms (ICFs) are green building components that are primarily used for residential wall construction. Unlike most polystyrene based ICF variants, the Faswall ICFs used in these experiments were significantly denser because they were made from recycled wood particles and cement. The current design approach for structures constructed with this type of wall form only allows the designer to consider the contribution of the reinforced concrete cores. Previous research has shown that this approach may be conservative. This project experimentally evaluated the lateral structural response of these types of grid ICF walls under increasing amplitude of in-plane cyclic loading. …

Stress Analysis For Chip Scale Packages With Embedded Active Devices Under Thermal Cycling, Hyunwook Yeo

Dissertations and Theses

One of the main challenges in the electronics manufacturing and packaging development is how to integrate more functions inside the same or even smaller size. To meet the demand for higher integration, the interest toward passive and active component embedding has been increasing during the past few years. One of the main reasons for the growing interest toward embedded active components, in addition to demand for higher packaging density, is the need for better electrical performance of the component assemblies. However, it is little known how embedded IC and passives affect the reliability of IC packaging.

Solder joints have been …

Local Vibrational Modes Competitions In Mn-Doped Zno Epitaxial Films With Tunable Ferromagnetism, Qiang Cao, Maoxiang Fu, Guolei Liu, Huaijin Zhang, Shishen Yan, Yanxue Chen, Liangmo Mei, Jun Jiao

Mechanical and Materials Engineering Faculty Publications and Presentations

We reported spectroscopic investigations of high quality Mn-doped ZnO (ZnMnO) films grown by oxygen plasma-assisted molecular beam epitaxy. Raman scattering spectra revealed two local vibrational modes (LVMs) associated with Mn dopants at 523 and 712cm^-1. The LVMs and magnetic properties of ZnMnO films can be synchronously modulated by post annealing processing or by introducing tiny Co. The relative intensity of two LVMs clearly shows competitions arising from uncompensated acceptor and donor defects competition for ferromagnetic and nonmagnetic films. The experimental results indicated that LVM at 523 cm^-1 is attributed to Mn—(Zinc-vacancy) complexes, while LVM at 712 cm …

Zno Nanosheet Arrays Constructed On Weaved Titanium Wire For Cds-Sensitized Solar Cells, Cuncun Wu, Lin Wei, Yitan Li, Chang Liu, Jun Jiao, Yanxue Chen, Liangmo Mei

Mechanical and Materials Engineering Faculty Publications and Presentations

Ordered ZnO nanosheet arrays were grown on weaved titanium wires by a low-temperature hydrothermal method. CdS nanoparticles were deposited onto the ZnO nanosheet arrays using the successive ionic layer adsorption and reaction method to make a photoanode. Nanoparticle-sensitized solar cells were assembled using these CdS/ZnO nanostructured photoanodes, and their photovoltaic performance was studied systematically. The best light-to-electricity conversion efficiency was obtained to be 2.17% under 100 mW/cm/cm² illumination, and a remarkable shortcircuit photocurrent density of approximately 20.1 mA/cm² was recorded, which could attribute to the relatively direct pathways for transportation of electrons provided by ZnO nanosheet arrays as …

Cds Quantum Dot-Sensitized Solar Cells Based On Nano-Branched Tio2 Arrays, Chang Liu, Yitan Li, Lin Wei, Cuncun Wu, Yanxue Chen, Liangmo Mei, Jun Jiao

Mechanical and Materials Engineering Faculty Publications and Presentations

Nano-branched rutile TiO2 nanorod arrays were grown on F:SnO2 conductive glass (FTO) by a facile, two-step wet chemical synthesis process at low temperature. The length of the nanobranches was tailored by controlling the growth time, after which CdS quantum dots were deposited on the nano-branched TiO2 arrays using the successive ionic layer adsorption and reaction method to make a photoanode for quantum dot-sensitized solar cells (QDSCs). The photovoltaic properties of the CdS-sensitized nano-branched TiO2 solar cells were studied systematically. A short-circuit current intensity of approximately 7 mA/cm2 and a light-to-electricity conversion efficiency of 0.95% were recorded for cells based on …

Zno Nanoneedle/H2o Solid-Liquid Heterojunction-Based Self-Powered Ultraviolet Detector, Qinghao Li, Lin Wei, Yanru Xie, Kai Zhang, Lei Liu, Dapeng Zhu, Jun Jiao, Yanxue Chen, Shishen Yan, Guolei Liu, Liangmo Mei

Physics Faculty Publications and Presentations

ZnO nanoneedle arrays were grown vertically on a fluorine-doped tin oxide-coated glass by hydrothermal method at a relatively low temperature. A self-powered photoelectrochemical cell-type UV detector was fabricated using the ZnO nanoneedles as the active photoanode and H2O as the electrolyte. This solid-liquid heterojunction offers an enlarged ZnO/water contact area and a direct pathway for electron transport simultaneously. By connecting this UV photodetector to an ammeter, the intensity of UV light can be quantified using the output short-circuit photocurrent without a power source. High photosensitivity, excellent spectral selectivity, and fast photoresponse at zero bias are observed in this UV detector. …

Solid State Pre-Formed Electronics Adhesive (Spea), Alexander Randon Cope

Dissertations and Theses

In mobile and handheld consumer electronic markets, product use conditions drive the requirement for mechanical strength and device durability. The majority of relatively large form factor electronic components in a laptop, mobile internet device, PDA, or mobile phone use an adhesive as a stiffener to help protect the component from physical stresses imposed by daily wear and tear. Described herein is an innovative solution referred to as Solid State Pre-Formed Electronics Adhesive (SPEA), which enables a decrease in circuit board manufacturing throughput time while increasing mechanical durability with a consistent and characterized adhesive application process.

Today, many consumer electronic ODM's …

Remotely Accessible Instrumented Monitoring Of Global Development Programs: Technology Development And Validation, Evan A. Thomas, Zdenek Zumr, Jodi Graf, Carson A. Wick, James H. Mccellan, Zachary Imam, Christina Barstow, Kelly Spiller, Michael Fleming

Mechanical and Materials Engineering Faculty Publications and Presentations

Many global development agencies self-report their project outcomes, often relying on subjective data that is collected sporadically and communicated months later. These reports often highlight successes and downplay challenges. Instrumented monitoring via distributed data collection platforms may provide crucial evidence to help inform the sector and public on the effectiveness of aid, and the on-going challenges. This paper presents the process of designing and validating an integrated sensor platform with cellular-to-internet reporting purposely targeted at global development programs. The integrated hardware platform has been applied to water, sanitation, energy and infrastructure interventions and validated through laboratory calibration and field observations. …

Energy And Climate Interactions In The Urban Environment, David J. Sailor

Mechanical and Materials Engineering Faculty Publications and Presentations

This presentation focuses on sustainable design choices and characteristics

An In Situ Experimental Study Of Grain Growth In A Nanocrystalline Fe91ni8zr1 Alloy, Hasan Kotan, Kris A. Darling, Mostafa Saber, Ronald O. Scattergood, Carl C. Koch

Mechanical and Materials Engineering Faculty Publications and Presentations

Grain growth and microstructural evolution of thermally stabilized Fe91Ni8Zr1 were investigated by in situ and ex situ studies. Our investigations suggest that the microstructural evolution is fairly slow and the microstructure shows stabilization up to about 700 °C. Above this temperature, a certain fraction of grains grow abnormally into the nanocrystalline matrix, resulting in a bimodal microstructure and causing the complete loss of thermal stability. The reason for abnormal grain growth and the loss of thermal stability is identified as the appearance of the fcc γ-phase and consequent reduction in the total area of grain boundaries and the overall stored …